Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Single molecule tunneling spectroscopy investigation of reversibly switched dipolar vanadyl phthalocyanine on graphite

We report a spatially resolved scanning tunneling spectroscopy (STS) investigation of reversibly switchable dipolar vanadyl phthalocyanine (VOPc) on graphite by using low temperature scanning tunneling microscopy. VOPc molecule can be switched between O-up and O-down configurations by changing the polarity of the pulse voltage applied to the tip, actuated by the inelastic tunneling electrons. The spatially resolved STS measurements allow the identification of the electronic structures of VOPc with different dipole orientation. The present approach provides geometry images and electronic characterization of a molecular switch on surface spontaneously.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Deuteron irradiation of W and WO 3 for production of high specific activity 186 Re: Challenges associated with thick target preparation

This investigation evaluated target fabrication and beam parameters for scale-up production of high specific activity 186 Re using deuteron irradiation of enriched 186 W via the 186 W(d,2n) 186 Re reaction. Thick W and WO 3 targets were prepared, characterized and evaluated in deuteron irradiations. Full-thickness targets, as determined using SRIM, were prepared by uniaxi-ally pressing powdered natural abundance W and WO 3 , or 96.86% enriched 186 W, into Al target supports. Alternatively, thick targets were prepared by pressing 186 W between two layers of graphite powder or by placing pre-sintered (1105°C, 12 hours) natural abundance WO 3 pellets into an Al target support. Assessments of structural integrity were made on each target pre-pared. Prior to irradiation, material composition analyses were conducted using SEM, XRD, and Raman spectroscopy. With-in a minimum of 24 hours post irradiation, gamma-ray spectroscopy was performed on all targets to assess production yields and radionuclidic byproducts. Problems were encountered with the structural integrity of some pressed W and WO 3 pellets before and during irradiation, and target material characterization results could be correlated with the structural integrity of the pressed target pellets. Under the conditions studied, the findings suggest that all WO 3 targets prepared and studied were unacceptable. By contrast, 186W metal was found to be a viable target material for 186 Re production. Lastly, thick targets prepared with powdered 186W pressed between layers of graphite provided a particularly robust target configuration.

43 PARTICLE ACCELERATORS↗

Nitrogen-doped mesoporous carbon for energy storage in vanadium redox flow batteries

We demonstrate a novel electrode material-nitrogen-doped mesoporous carbon (NMC)-for vanadium redox flow batteries. Mesoporous carbon (MC) is prepared using a soft-template method and doped with nitrogen by heat-treating MC in NH 3 . NMC is characterized with X-ray photoelectron spectroscopy and transmission electron microscopy. The redox reaction of [VO] 2+ /[VO 2 ] + is characterized with cyclic voltammetry and electrochemical impedance spectroscopy. The electrocatalytic kinetics of the redox couple [VO] 2+ /[VO 2 ] + is significantly enhanced on NMC electrode compared with MC and graphite electrodes. The reversibility of the redox couple [VO] 2+ /[VO 2 ] + is greatly improved on NMC (0.61 for NMC vs. 0.34 for graphite). Nitrogen doping facilitates the electron transfer on the electrode/electrolyte interface for both oxidation and reduction processes. NMC is a promising electrode material for redox flow batteries.

25 ENERGY STORAGE↗

Targeted masking enables stable cycling of LiNi 0.6 Co 0.2 Mn 0.2 O 2 at 4.6V

Layered LiNi x Co y Mn 1–x-y O 2 (NCM, or NCMxy(1-x-y)) is a dominant family of cathode materials for lithium-ion batteries (LIBs) due to its high energy density. Among all NCM cathode materials, NCM622 possess the optimal energy density at high potential (≥ 4.6 V vs. Li/Li + ). However, the practical application of NCM622 at high voltage (≥ 4.6 V) is limited by its parasitic reactions and associated safety concerns. Completely physical isolation has been considered as the main approach to mitigate the parasitic reaction. It has also been previously demonstrated that the interface reaction has active site selectivity, and that the reactivity of the active sites can effectively suppressed by blocking the chemically active sites. Herein, a targeted masking by LiFePO 4 @C nanoplates is reported to unlock the stable performance of NCM622 up to 4.6 V vs. Li/Li + . The (targeted masked-NCM622)|graphite pouch cell shows 86.5% capacity retention after 1000 cycles and its maximum temperature during thermal runaway is dramatically reduced from 570 °C to 415 °C. Systematic in/ex situ characterizations, first-principles calculations and half/pouch targeted LiFePO 4 @C covers the surface of NCM partcell evaluation prove that PO 4 3- is preferentially adsorbed on transition metal sites, stabilizing both the transition metal ions and oxygen ions on the surface against the ethylene carbonate-containing traditional electrolyte even under high voltage (≥ 4.6 V vs. Li/Li + ). Furthermore, this work opens up new venue for rational design of high-performance cathode materials through a low-cost and scalable decoration process, and reveal a new understanding of interfacial activity of materials.

25 ENERGY STORAGE↗

The Evolution of LiNi 0.5 Mn 0.3 Co 0.2 O 2 Particle Damage from Fast Charging in Optimized, Full Li-Ion Cells

Fast charging batteries are critical to the widespread adoption of electric vehicles to compete with refueling times of combustion-based vehicles. In the near term, adapting current commercial battery technologies to perform better under fast charging conditions through engineering optimizations will greatly expedite the process while exploratory fast-charging electrode materials are being pursued. To do so, the degradation modes in optimized Li-ion batteries need to be completely explored to understand fast charging limits while maintaining a high energy density and a long cycle life. While lithium plating on graphite still remains a challenge, cathode degradation also plays a key role in battery performance. In this work, we used nano- and micro-X-ray computed tomography to characterize the mechanical degradation of LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532) in optimized Li-ion batteries cycled at three rates, 1C, 6C, and 9C, and at different stages of cycle life, 225 and 600 cycles. We report despite using a conservative upper voltage cutoff limit aimed to minimize extensive cathode degradation, higher charging rates and increased cycling caused the polycrystalline NMC532 particles to fracture and pulverize, which likely drives cathode capacity fade and contributes to the decrease in overall cell performance.

25 ENERGY STORAGE↗

Graphitizable Pitch from Microwave Plasma Pyrolysis of Natural Gas

An innovative approach of microwave plasma was utilized to convert natural gas into tar, from which a highly graphitizable pitch was derived using fractional distillation. The natural gas-derived pitch (NGDP) was thoroughly characterized, and the graphitizability of the carbonized NGDP was assessed using polarized light microscopy. The NGDP and, for comparison, needle coke, petroleum coke, and shot coke were subjected to graphitization heat treatment (GR) at 2500 °C. Results indicate that the graphitizability of the NGDP exceeds those of all industrial standard cokes. The GR-NGDP showed the highest degree of graphitization and crystallite size among all samples.

03 NATURAL GAS↗

Boosting the cycling stability of Ni-rich layered oxide cathode by dry coating of ultrastable Li 3 V 2 (PO 4 ) 3 nanoparticles

Nickel (Ni)-rich layered oxides such as LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622) represent one of the most promising candidates for next-generation high-energy lithium-ion batteries (LIBs). However, the pristine Ni-rich cathode materials usually suffer from poor structural stability during cycling. In this work, we demonstrate a simple but effective approach to improve the cycling stability of the NCM622 cathode by dry coating of ultrastable Li 3 V 2 (PO 4 ) 3 -carbon (LVP-C) nanoparticles, which leads to a robust composite cathode (NCM622/LVP-C) without sacrificing the specific energy density compared with pristine NCM622. The optimal NCM622/LVP-C composite presents a high specific capacity of 162 mA h g -1 at 0.5 C and excellent cycling performance with 85.0% capacity retention after 200 cycles at 2 C, higher than that of the pristine NCM622 (67.6%). Systematic characterization confirms that the LVP-C protective layer can effectively reduce the side reactions, restrict the cation mixing of NCM622 and improve its structural stability. Moreover, the NCM622/LVP-C||graphite full cells also show a commercial-level capacity of 3.2 mA h cm -2 and much improved cycling stability compared with NCM622/LVP-C||graphite full cells, indicating the great promise for low-cost, high-capacity and long-life LIBs.

36 MATERIALS SCIENCE↗

Development of Lithium Dimethyl Phosphate as an Electrolyte Additive for Lithium Ion Batteries

The novel electrolyte additive lithium dimethyl phosphate (LiDMP) has been synthesized and characterized. Incorporation of LiDMP (0.1% wt) into LiPF 6 in ethylene carbonate (EC) / ethyl methyl carbonate (EMC) (3:7 wt) results in improved rate performance and reduced impedance for graphite / LiNi 1/3 Mn 1/3 Co 1/3 O 2 cells. Ex-situ surface analysis of the electrodes suggests that incorporation of LiDMP results in a modification of the solid electrolyte interphase (SEI) on the anode. A decrease in the concentration of lithium alkyl carbonates and an increase in the concentration of lithium fluoro phosphates are observed. The change in the anode SEI structure is responsible for the increased rate performance and decreased cell impedance.

25 ENERGY STORAGE↗

Status and Update of the RaDIATE Collaboration R&D Program

The Radiation Damage In Accelerator Target Environments (RaDIATE) collaboration was founded in 2012 and currently consists of over 50 participants and 11 institutions globally. Due to the increasing power of future proton accelerator sources on target facilities, there is a critical need to further the understanding of the physical and thermo-mechanical radiation response of target facility materials. Thus, the primary objective of the RaDIATE collaboration is to draw on existing expertise in the nuclear materials and accelerator targets fields to generate new and useful materials data for application within the accelerator and fission/fusion communities. Current research activities of the collaboration include post irradiation examination (PIE) of decommissioned components from existing beamlines such as the NuMI beryllium beam window and graphite NT-02 target material. PIE of these components includes advanced microstructural analyses (SEM/TEM, EBSD, EDS) and micro-mechanic s technique such as nano-indentation, to help characterize any microstructural radiation damage incurred during operation. New irradiation campaigns of various candidate materials at both low and high energy beam facilities are also being pursued. Beryllium helium implantation studies at the University of Surrey as well as high energy proton irradiation of various materials at Brookhaven National Laboratory’s BLIP facility have been initiated. The program also extends to beam-induced thermal shock experiments using high intensity beam pulses at CERN’s HiRadMat facility, followed by advanced PIE activities to evaluate thermal shock resistance of the materials. The continuing research activities with preliminary results, as well as the future plans of the RaDIATE Collaboration R&D program will be discussed.

43 PARTICLE ACCELERATORS↗

DOE Award No. DE-FC36-03GO13108 NOVEL NON-PRECIOUS METAL CATALYSTS FOR PEMFC: CATALYST SELECTION THROUGH MOLECULAR MODELING AND DURABILITY STUDIES Final Report (September 2003 – October 2008)

The objective of this project is to develop novel non-precious metal electrocatalysts for oxygen reduction reaction (ORR), and demonstrate the potential of the catalysts to perform at least as good as conventional Pt catalysts currently in use in polymer electrolyte membrane fuel cell (PEMFC) with a cost at least 50 % less than a target of 0.2 g (Pt loading)/peak kW and with durability > 2,000 h operation with less than 10 % power degradation. A novel nitrogen-modified carbon-based catalyst was obtained by modifying carbon black with nitrogen-containing organic precursor in the absence of transition metal precursor. The catalyst shows the onset potential of approximately 0.76 V (NHE) for ORR and the amount of H2O2 of approximately 3% at 0.5 V (NHE). Furthermore, a carbon composite catalyst was achieved through the high-temperature pyrolysis of the precursors of transition metal (Co and Fe) and nitrogen supported on the nitrogen-modified carbon-based catalyst, followed by chemical post-treatment. This catalyst showed an onset potential for ORR as high as 0.87 V (NHE), and generated less than 1 % of H2O2. The PEM fuel cell exhibited a current density of 2.3 A cm-2 at 0.2 V for a catalyst loading of 6.0 mg cm-2. No significant performance degradation was observed for 480 h continuous operation. The characterization studies indicated that the metal-nitrogen chelate complexes decompose at the temperatures above 800 oC. During the pyrolysis, the transition metals facilitate the incorporation of pyridinic and graphitic nitrogen groups into the carbon matrix, and the carbon surface modified with nitrogen is active for ORR. In order to elucidate the role of transition metal precursor played in the formation of active sites in the non-precious metal catalysts, a novel ruthenium-based chelate (RuNx) catalyst was synthesized by using RuCl3 and propylene diammine as the Ru and N precursors, respectively, followed by high-temperature pyrolysis. This catalyst exhibited comparable catalytic activity and selectivity for ORR as the Pt catalyst. A theoretical analysis is made of the four-electron reduction reaction of oxygen to water over the mixed anion and cation (202) surface of pentlandite structure Co9Se8, one of several selenide phases. Reversible potentials for forming adsorbed reaction intermediates in acid are predicted using adsorption energies calculated with the Vienna ab initio simulation program (VASP) and the known bulk solution values together in a linear Gibbs energy relationship. The effect of hydrophobic and structural properties of a single/dual-layer cathode gas diffusion layer on mass transport in PEM fuel cells was studied using an analytical expression. The simulations indicated that liquid water transport at the cathode is controlled by the fraction of hydrophilic surface and the average pore diameter in the cathode gas diffusion layer. The optimized hydrophobicity and pore geometry in a dual-layer cathode GDL leads to an effective water management, and enhances the oxygen diffusion kinetics.

08 HYDROGEN↗

DOE Award No. DE-FC36-03GO13108 NOVEL NON-PRECIOUS METAL CATALYSTS FOR PEMFC: CATALYST SELECTION THROUGH MOLECULAR MODELING AND DURABILITY STUDIES Final Report (September 2003 – October 2008)

The objective of this project is to develop novel non-precious metal electrocatalysts for oxygen reduction reaction (ORR), and demonstrate the potential of the catalysts to perform at least as good as conventional Pt catalysts currently in use in polymer electrolyte membrane fuel cell (PEMFC) with a cost at least 50 % less than a target of 0.2 g (Pt loading)/peak kW and with durability > 2,000 h operation with less than 10 % power degradation. A novel nitrogen-modified carbon-based catalyst was obtained by modifying carbon black with nitrogen-containing organic precursor in the absence of transition metal precursor. The catalyst shows the onset potential of approximately 0.76 V (NHE) for ORR and the amount of H2O2 of approximately 3% at 0.5 V (NHE). Furthermore, a carbon composite catalyst was achieved through the high-temperature pyrolysis of the precursors of transition metal (Co and Fe) and nitrogen supported on the nitrogen-modified carbon-based catalyst, followed by chemical post-treatment. This catalyst showed an onset potential for ORR as high as 0.87 V (NHE), and generated less than 1 % of H2O2. The PEM fuel cell exhibited a current density of 2.3 A cm-2 at 0.2 V for a catalyst loading of 6.0 mg cm-2. No significant performance degradation was observed for 480 h continuous operation. The characterization studies indicated that the metal-nitrogen chelate complexes decompose at the temperatures above 800 oC. During the pyrolysis, the transition metals facilitate the incorporation of pyridinic and graphitic nitrogen groups into the carbon matrix, and the carbon surface modified with nitrogen is active for ORR. In order to elucidate the role of transition metal precursor played in the formation of active sites in the non-precious metal catalysts, a novel ruthenium-based chelate (RuNx) catalyst was synthesized by using RuCl3 and propylene diammine as the Ru and N precursors, respectively, followed by high-temperature pyrolysis. This catalyst exhibited comparable catalytic activity and selectivity for ORR as the Pt catalyst. A theoretical analysis is made of the four-electron reduction reaction of oxygen to water over the mixed anion and cation (202) surface of pentlandite structure Co9Se8, one of several selenide phases. Reversible potentials for forming adsorbed reaction intermediates in acid are predicted using adsorption energies calculated with the Vienna ab initio simulation program (VASP) and the known bulk solution values together in a linear Gibbs energy relationship. The effect of hydrophobic and structural properties of a single/dual-layer cathode gas diffusion layer on mass transport in PEM fuel cells was studied using an analytical expression. The simulations indicated that liquid water transport at the cathode is controlled by the fraction of hydrophilic surface and the average pore diameter in the cathode gas diffusion layer. The optimized hydrophobicity and pore geometry in a dual-layer cathode GDL leads to an effective water management, and enhances the oxygen diffusion kinetics.

08 HYDROGEN↗

Two types of carbon nanocomposites: Graphite encapsulated iron nanoparticles and thin carbon nanotubes supported on thick carbon nanotubes, synthesized using PECVD

In this work, graphite encapsulated Fe nanoparticles and thin carbon nanotubes (CNTs) supported on the pristine CNTs, respectively, were synthesized using plasma enhanced chemical vapor deposition via efficiently controlling the flow rate of discharging CH{sub 4} and H{sub 2} gas. The properties of the obtained hybrid materials were characterized with superconducting quantum interference and field emission measurements. The results showed that the encapsulated Fe nanoparticles had diameters ranging from 1 to 30 nm, and this hybrid nanocomposite exhibited a ferromagnetic behavior at room temperature. Thin CNTs with an average diameter of 6 nm were attached to the surface of the prepared CNTs, which exhibited a lower turn-on field and higher emission current density than the pristine CNTs. The Fe nanoparticles either encapsulated with graphite or used as catalyst for thin CNTs growth were all originated from the pyrolysis of ferrocene. - Graphical abstract: Graphite encapsulated Fe nanoparticles and thin carbon nanotubes supported on the pristine carbon nanotubes, respectively, were synthesized using plasma enhanced chemical vapor deposition.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Multiscale modeling of polyisoprene on graphite

The local dynamics and the conformational properties of polyisoprene next to a smooth graphite surface constructed by graphene layers are studied by a multiscale methodology. First, fully atomistic molecular dynamics simulations of oligomers next to the surface are performed. Subsequently, Monte Carlo simulations of a systematically derived coarse-grained model generate numerous uncorrelated structures for polymer systems. A new reverse backmapping strategy is presented that reintroduces atomistic detail. Finally, multiple extensive fully atomistic simulations with large systems of long macromolecules are employed to examine local dynamics in proximity to graphite. Polyisoprene repeat units arrange close to a parallel configuration with chains exhibiting a distribution of contact lengths. Efficient Monte Carlo algorithms with the coarse-grain model are capable of sampling these distributions for any molecular weight in quantitative agreement with predictions from atomistic models. Furthermore, molecular dynamics simulations with well-equilibrated systems at all length-scales support an increased dynamic heterogeneity that is emerging from both intermolecular interactions with the flat surface and intramolecular cooperativity. This study provides a detailed comprehensive picture of polyisoprene on a flat surface and consists of an effort to characterize such systems in atomistic detail.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

ANS MiNES 2023 Poster

The dynamic mechanical properties of four varieties of high purity graphite as well as the depth of penetration (DoP) of a small-scale shaped charge into these grades was experimentally determined. The grades chosen were PCEA, NBG-18, and NBG-25. These grades provide a wide range of physical properties: in density from 1.80 – 1.85 g/cc, in maximum particle size from 10s to 1000s of µm, and in porosity from 18% to 20%. The quasistatic and dynamic compressive strengths of each grade were determined and correlated to their physical properties. The split Hopkinson pressure bar experiments showed both the dynamic strength and dominant shear failure mechanisms. A small scale shaped charge was used to compare the resistance of graphite to hypervelocity jet impacts: the Teledyne RP-4. The RP-4 has a 1.01” outer diameter and 3.44 g of RDX with an RP-80 booster (86 mg PETN + 123 mg RDX). A select number of samples were analyzed using X-Ray Computed Tomography (XCT), allowing for the full characterization of the undisturbed wound channel. A selection of other samples were physically sectioned and wound channels mapped from the sections. In addition to DoP, the wound geometry was characterized in terms of total volume and diameter at different depths. The wound channel characteristics for each grade were correlated to the compressive strengths and physical properties. In several of the test samples, the wound channel diameter was smaller than the diameter of the shaped charge slug just behind where the slug had penetrated the sample. These results indicated that the wound geometry was dependent on the compressive hysteresis behavior of graphite.

36 MATERIALS SCIENCE↗

Small Specimen Data from a High Temperature HFIR Irradiation Experiment

The HTV capsule is a High Flux Isotope Reactor (HFIR) target-rod capsule designed to operate at very high temperatures. The graphite containing section of the capsule (in core) is approximately 18 inches (457.2 mm) long and is separated into eight temperature zones. The specimen diameters within each zone are set to achieve the desired gas gap and hence design temperature (900 C, 1200 C or 1500 C). The capsule has five zones containing 0.400 inch (10.16 mm) diameter specimens, two zones containing 0.350 inch (8.89 mm) diameter specimens and one zone containing 0.300 inch (7.62 mm) diameter specimens. The zones have been distributed within the experiment to optimize the gamma heating from the HFIR core as well as minimize the axial heat flow in the capsule. Consequently, there are two 900 C zones, three 1200 C zones, and three 1500 C zones within the HTV capsule. Each zone contains nine specimens 0.210 0.002 inches (5.334 mm) in length. The capsule will be irradiated to a peak dose of 3.17 displacements per atom. The HTV specimens include samples of the following graphite grades: SGL Carbon s NBG-17 and NBG-18, GrafTech s PCEA, Toyo Tanso s IG-110, Mersen s 2114 and the reference grade H-451 (SGL Carbon). As part of the pre-irradiation program the specimens were characterized using ASTM Standards C559 for bulk density, and ASTM C769 for approximate Young s modulus from the sonic velocity. The probe frequency used for the determination of time of flight of the ultrasonic signal was 2.25 MHz. Marked volume (specimen diameter) effects were noted for both bulk density (increased with increasing specimen volume or diameter) and Dynamic Young s modulus (decreased with increasing specimen volume or diameter). These trends are extended by adding the property vs. diameter data for unirradiated AGC-1 creep specimens (nominally 12.5 mm-diameter x 25.4 mm-length). The relatively large reduction in Dynamic Young s Modulus was surprising given the trend for increasing density with increasing volume. The graphite-filler particle size was noted to be influential in the volume dependency data, with finer grained graphites showing the least specimen volume/diameter effect. Here the volume dependency trends are discussed in terms of the graphite s filler-particle size and texture.

graphite↗

Pulse laser induced graphite-to-diamond phase transition: the role of quantum electronic stress

First-principles calculations show that the pulse laser induced graphite-to-diamond phase transition is related to the lattice stress generated by the excited carriers, termed as “quantum electronic stress (QES)”. We found that the excited carriers in graphite generate a large anisotropic QES that increases linearly with the increasing carrier density. Using the QES as a guiding parameter, structural relaxation spontaneously transforms the graphite phase into the diamond phase, as the QES is reduced and minimized. Our results suggest that the concept of QES can be generally applied as a good measure to characterize the pulse laser induced phase transitions, in analogy to pressure induced phase transitions.

Wang, ZhengFei↗

A simple centrifuge cell method for ex situ quantification of electrical conductivity of slurry electrode materials

We present the design, experimental procedure, and experimental evaluation of a system for fast, simple, and ex situ characterization of electrical conductivity of slurry electrode materials. The system uses a custom-designed electrochemical cell compatible with centrifugation in a swing-bucket centrifuge. The cell features cylindrical graphite electrodes that are partially sheathed so as to expose only 2 mm of the electrode surface to the bottom region of the packed particulate pellet. Also presented is a conduction model that provides a shape factor for estimating effective conductivity. We tested aqueous solutions of carbon black (CB), activated carbon (AC), and mixtures thereof. These particles were dispersed in 0.0 and 0.5 M NaCl solutions. Measurements show that the effective conductivity initially increases linearly with pellet mass and then saturates at higher masses. Notably, CB exhibited a fivefold increase in conductivity than AC at equal pellet masses. CB/AC mixtures at a fixed pellet mass were tested with CB mass fractions of 0 to 100%. Interestingly, the mixture conductivity was found to be a non-monotonic function of CB mass fraction, with a maximum conductivity at about 60 % CB mass fraction. At this maximum, the mixture conductivity is approximately 30 % higher than pure CB. NaCl concentration in the slurry solution had no effects on conductivity. These results highlight the interactions between slurry electrode composition and compaction, offering insights for optimizing slurry electrodes. Furthermore, the system and results may also be applicable to evaluation of particulate materials (including slurries) used for Li-ion batteries, capacitive deionization, fuel cells, and flow electrodes.

Capacitive deionization↗

Self-healing SEI enables full-cell cycling of a silicon-majority anode with a coulombic efficiency exceeding 99.9%

Despite active developments, full-cell cycling of Li-battery anodes with >50 wt% Si (a Si-majority anode, SiMA) is rare. The main challenge lies in the solid electrolyte interphase (SEI), which when formed naturally (nSEI), is fragile and cannot tolerate the large volume changes of Si during lithiation/delithiation. An artificial SEI (aSEI) with a specific set of mechanical characteristics is henceforth designed; we enclose Si within a TiO 2 shell thinner than 15 nm, which may or may not be completely hermetic at the beginning. In situ TEM experiments show that the TiO 2 shell exhibits 5× greater strength than an amorphous carbon shell. Void-padded compartmentalization of Si can survive the huge volume changes and electrolyte ingression, with a self-healing aSEI + nSEI. The half-cell capacity exceeds 990 mA h g -1 after 1500 cycles. To improve the volumetric capacity, we further compress SiMA 3-fold from its tap density (0.4 g cm -3 ) to 1.4 g cm -3 , and then run the full-cell battery tests against a 3 mA h cm -2 LiCoO 2 cathode. Despite some TiO 2 enclosures being inevitably broken, 2× the volumetric capacity (1100 mA h cm -3 ) and 2× the gravimetric capacity (762 mA h g -1 ) of commercial graphite anode is achieved in stable full-cell battery cycling, with a stabilized areal capacity of 1.6 mA h cm -2 at the 100th cycle. The initial lithium loss, characterized by the coulombic inefficiency (CI), is carefully tallied on a logarithmic scale and compared with the actual full-cell capacity loss. In conclusion, it is shown that a strong, non-adherent aSEI, even if partially cracked, facilitates an adaptive self-repair mechanism that enables full-cell cycling of a SiMA, leading to a stabilized coulombic efficiency exceeding 99.9%.

25 ENERGY STORAGE↗