Results for “hover” — Page 28

NASA NTRS1998

Application of Pressure-Sensitive Paint to Rotorcraft

In this presentation, a plan to develop methods for applying pressure-sensitive paint to rotorcraft will be described. These methods are needed because flows over rotor blades are typically very complex and poorly understood and because conventional methods for measuring unsteady pressures on rotor blades (using unsteady pressure transducers provide grossly inadequate spatial resolution. Since PSP is a surface, rather than a point, measurement technique, it has the potential to significantly increase the spatial resolution )f pressure measurements on rotor blades. PSP techniques currently in use at Ames were developed for measuring steady pressures on rigid, complex airplane configurations in large, production wind tunnels. Applying PSP to rotorcraft requires a significant departure from these techniques. First and most importantly new, fast-responding and self-referencing pressure paints are required. The paints must be fast (98% response in 1-5 msec) to resolve flow unsteadiness; they must be self-referencing (or "binary") to account for changes in incident light intensity due to deflection of flexible rotors. Self-referencing paints have been used at Ames for some time; however, these paints have response times that are far too long for unsteady applications. Flash illumination is required to resolve flow unsteadiness and to minimize image blurring due to relative motion between the model and the camera. Current practice at Ames is to use continuous illumination Finally, "in situ" paint calibration versus measurements by pressure transducers, which is current Ames practice, is not practical because of the difficulty and expense of installing transducers in rotor blades. Instead, the paint must be calibrated "a priori" in a calibration chamber. A sequence of five experiments that systematically isolates and addresses the problems involved in making PSP measurements on rotor blades has been planned. These are: (1) measurements on a rigid rotor in hover; (2) measurements on a flexible rotor in hover; measurements of paint response time in a calibration apparatus; (4) measurements on a rigid, two-dimensional oscillating airfoil; and (5) measurements on a flexible rotor in forward flight. Experiments were recently conducted at Ames where PSP measurements were made on a rigid oscillating airfoil (experiment type 4) and on a flexible rotor in hover (experiment type 2). Preliminary results from these experiments will be discussed.

Schairer, Edward T.↗

NASA NTRS2002

Piloted Evaluation of a UH-60 Mixer Equivalent Turbulence Simulation Model

A simulation study of a recently developed hover/low speed Mixer Equivalent Turbulence Simulation (METS) model for the UH-60 Black Hawk helicopter was conducted in the NASA Ames Research Center Vertical Motion Simulator (VMS). The experiment was a continuation of previous work to develop a simple, but validated, turbulence model for hovering rotorcraft. To validate the METS model, two experienced test pilots replicated precision hover tasks that had been conducted in an instrumented UH-60 helicopter in turbulence. Objective simulation data were collected for comparison with flight test data, and subjective data were collected that included handling qualities ratings and pilot comments for increasing levels of turbulence. Analyses of the simulation results show good analytic agreement between the METS model and flight test data, with favorable pilot perception of the simulated turbulence. Precision hover tasks were also repeated using the more complex rotating-frame SORBET (Simulation Of Rotor Blade Element Turbulence) model to generate turbulence. Comparisons of the empirically derived METS model with the theoretical SORBET model show good agreement providing validation of the more complex blade element method of simulating turbulence.

Lusardi, Jeff A.↗

NASA NTRS1957

Concluding Report of Free-Spinning, Tumbling, and Recovery Characteristics of a 1/18-Scale Model of the Ryan X-13 Airplane, Coord. No. AF-199

An investigation has been completed in the Langley 20-foot free-spinning tunnel on a l/18-scale model of the Ryan X-13 airplane to determine its spin, recovery, and tumbling characteristics, and to determine the minimum altitude from which a belly landing could be made in case of power failure in hovering flight. Model spin tests were conducted with and without simulated engine rotation. Tests without simulated engine rotation indicated two types of spins: one, a slightly oscillatory flat spin; and the other, a violently oscillatory spin. Tests with simulated engine rotation indicated that spins to the left were fast rotating and steep and those to the right were slow rotating and flat. The optimum technique for recovery is reversal of the rudder to against the spin and simultaneous movement of the ailerons to full with the spin followed by movement of the elevators to neutral after the spin rotation ceases. Tumbling tests made on the model indicated that although the Ryan X-13 airplane will not tumble in the ordinary sense (end-over-end pitching motion), it may instead tend to enter a wild gyrating'motion. Tests made to simulate power failure in hovering flight by dropping the model indicated that the model entered what appeared to be a right spin. An attempt should be made to stop this motion immediately by moving the rudder to oppose the rotation (left pedal), moving the ailerons to with the spin (stick right), and moving the stick forward after the spin rotation ceases to obtain flying speed for pullout. The minimum altitude required for a belly landing in case of power failure in hovering flight was indicated to be about 4,200 feet.

Bowman, James S., Jr.↗

NASA NTRS2006

Comanche Helmet-Mounted Display Heading-Tape Simulation

The Aeroflightdynamics Directorate (AMRDEC) conducted a simulation to assess the performance associated with a Contact Analog, world-referenced heading tape as implemented on the Comanche Helmet Integrated Display Sight System (HIDSS) when compared with a Compressed heading tape similar to that specified by the former Military Standard (MIL-STD) 1295. Six experienced pilots flew three modified Aeronautical Design Standards (ADS)-33 maneuvers (Hover Turn, Bob-up, Transient Turn) and a precision traffic pattern in the NASA Vertical Motion Simulator (VMS). Analysis of the pilot objective performance data and subjective handling qualities ratings (HQRs) showed the following: Compressed symbology in the Velocity Stabilization (VelStab) flight mode generally produced the most precise performances over Contact Analog symbology with respect to the heading, altitude, position, and time criteria specified for the maneuvers tested. VelStab outperformed the Automatic Flight Control System (AFCS) on all maneuvers achieving desired performance on most maneuvers for both symbol sets. Performance in the AFCS mode was generally desirable to adequate for heading and altitude and did not meet adequate standards for hover position and time for the Hover Turn and Bob-up maneuvers. VelStab and AFCS performance were nearly the same for the Transient Turn. Pilot comments concerning the Contact Analog heading-tape implementation were generally unfavorable in spite of the achieved levels of performance. HQRs showed Compressed symbology in the VelStab flight mode produced the lowest mean HQR, encompassing mixed ratings of satisfactory handling and needing improvement. All other symbology/flight-mode combinations yielded higher HQRs, which characterized opinions that deficiencies in aircraft handling due to HMD symbology would need improvement. Contact Analog heading tape and other symbology require improvement, especially when operating in the AFCS mode. NASA-TLX rated Compressed symbology in the VelStab flight mode as the least demanding on resources, closely followed by ratings for Contact Analog in the VelStab mode. In a similar pattern, TLX ratings for maneuvers completed in the AFCS mode yielded a higher level of resource demand with even slighter differences between Contact Analog and Compressed symbology sets. Further research should be conducted where objective data and subjective HQR ratings indicate a need for improvement. The areas requiring attention are those where the symbology implementation, the flight control system, or a combination of both caused workload to reach an objectionable level where adequate performance was either difficult to achieve or unachievable. These areas are clearly identified in this report. Symbology that received negative HQR comments by a majority of pilots should also be examined. The summary of pilot comments can be found in appendix A. Additional simulation trials should be considered to address the identified issues.

Turpin, Terry↗

NASA NTRS2006

Comanche Helmet-Mounted Display Symbology Simulation

The Aeroflightdynamics Directorate (AMRDEC) conducted a simulation to examine the performance of the Comanche Contact Analog world-referenced symbology displayed on the Comanche HIDSS when compared with a compressed symbology design similar to that specified by the former MIL-STD 1295. Six experimental test pilots flew one modified ADS-33 maneuver (hover turn, bob-up), an unusual attitude recovery, and two terrain flight tactical tasks in the NASA Vertical Motion Simulator (VMS). Analysis of the pilot objective performance data and subjective data showed the following results. Objective test results showed that 1295 symbology yielded more rapid maneuvering in the hover turn bob-up than Contact Analog symbology. The average margin of difference in the time to complete the maneuver was approximately two seconds, which was statistically significant. There were no significant differences measured between symbology sets with respect to altitude or position performance measures for all other maneuvers. The NOE target ID task data showed improved accuracy in determining heading to target when using Contact Analog over MIL-STD-1295. Subjective test results, including handling qualities ratings (HQRs) and NASA-TLX workload ratings, showed small but consistent advantages of 1295 symbology over Contact Analog for most parameters. For the bob-up maneuver, 1295 symbology handling qualities were rated Desired for lateral position error and time to complete whereas Contact Analog was rated adequate. The average HQRs for all other maneuvers were rated the same for both symbology sets. Pilot comments and the results of an online questionnaire more strongly favored 1295 over Contact Analog. Repeated comments from all six pilots led to a focus on design issues with six Contact Analog symbols. Those symbols were the heading tape, horizon line, radar altitude six-second predictor, the position of the torque symbol, the absence of a hover position cue, and the widespread positioning of the symbology to the outer edges of the display field-of-view. Pilots rated the present design of three of the six symbols as having safety-of-flight implications. Those symbols were the heading tape, horizon line, and six-second predictor. To summarize, test results showed no objective data that would warrant restricting experimental test pilots from flying constrained tasks. Small but consistent advantages were recorded for the MILSTD-1295 symbology design when executing ADS-33 constrained tasks. No general performance differences were recorded for the operational maneuvers (NOE, contour flight modes) except for the azimuth-to-target task, which favored the Contact Analog heading tape design. There were consistent and strong pilot comments supporting the MIL-STD-1295 design over Contact Analog in both this current simulation and in Comanche Sim I. Three Contact Analog symbols warrant modification and further evaluation to mitigate safety-of-flight implications noted by participating test pilots. A plan for symbology redesign and testing was developed. However, the Comanche program was cancelled by Department of Army in February 2004.

Turpin, Terry S.↗

NASA NTRS1995

Wingtip mounted, counter-rotating proprotor for tiltwing aircraft

A tiltwing aircraft, capable of in-flight conversion between a hover and forward cruise mode, employs a counter-rotating proprotor arrangement which permits a significantly increased cruise efficiency without sacrificing either the size of the conversion envelope or the wing efficiency. A benefit in hover is also provided because of the lower effective disk loading for the counter-rotating proprotor, as opposed to a single rotation proprotor of the same diameter. At least one proprotor is provided on each wing section, preferably mounted on the wingtip, with each proprotor having two counter-rotating blade rows. Each blade row has a plurality of blades which are relatively stiff-in-plane and are mounted such that cyclic pitch adjustments may be made for hover control during flight.

Wechsler, James K.↗

NASA NTRS2012

Detached Eddy Simulation of the UH-60 Rotor Wake Using Adaptive Mesh Refinement

Time-dependent Navier-Stokes flow simulations have been carried out for a UH-60 rotor with simplified hub in forward flight and hover flight conditions. Flexible rotor blades and flight trim conditions are modeled and established by loosely coupling the OVERFLOW Computational Fluid Dynamics (CFD) code with the CAMRAD II helicopter comprehensive code. High order spatial differences, Adaptive Mesh Refinement (AMR), and Detached Eddy Simulation (DES) are used to obtain highly resolved vortex wakes, where the largest turbulent structures are captured. Special attention is directed towards ensuring the dual time accuracy is within the asymptotic range, and verifying the loose coupling convergence process using AMR. The AMR/DES simulation produced vortical worms for forward flight and hover conditions, similar to previous results obtained for the TRAM rotor in hover. AMR proved to be an efficient means to capture a rotor wake without a priori knowledge of the wake shape.

Chaderjian, Neal M.↗

NASA NTRS2014

Aeromechanical Evaluation of Smart-Twisting Active Rotor

An investigation of Smart-Twisting Active Rotor (STAR) was made to assess potential benefits of the current active twist rotor concept for performance improvement, vibration reduction, and noise alleviation. The STAR rotor is a 40% Mach-scaled, Bo105 rotor with an articulated flap-lag hinge at 3.5%R and no pre-cone. The 0-5 per rev active twist harmonic inputs were applied for various flight conditions including hover, descent, moderate to high speed level flights, and slowed rotor high advance ratio. For the analysis, the STAR partners used multiple codes including CAMRAD II, S4, HOST, rFlow3D, elsA, and their associated software. At the high thrust level in hover, the 0 per rev active twist with 80% amplitude increased figure of merit (FM) by 0.01-0.02 relative to the baseline. In descent, the largest BVI noise reduction was on the order of 2 to 5 dB at the 3 per rev active twist. In the high speed case (mu = 0.35), the 2 per rev actuation was found to be the most effective in achieving a power reduction as well as a vibration reduction. At the 2 per rev active twist, total power was reduced by 0.65% at the 60 deg active twist phase, and vibration was reduced by 47.6% at the 45 deg active twist phase. The use of the 2 per rev active twist appears effective for vibration reduction. In the high advance ratio case (mu = 0.70), the 0 per rev actuation appeared to have negligible impact on performance improvement. In summary, computational simulations successfully demonstrated that the current active twist concept provided a significant reduction of the maximum BVI noise in descent, a significant reduction of the vibration in the high speed case, a small improvement on rotor performance in hover, and a negligible impact on rotor performance in forward flight.

Lim, Joon W.↗

NASA NTRS2016

Range and Endurance Tradeoffs on Personal Rotorcraft Design

Rotorcraft design has always been a challenging tradeoff among overall size, capabilities, complexity, and other factors based on available technology and customer requirements. Advancements in propulsion, energy systems and other technologies have enabled new vehicles and missions; complementary advances in analysis methods and tools enable exploration of these enhanced vehicles and the evolving mission design space. A system study was performed to better understand the interdependency between vehicle design and propulsion system capabilities versus hover / loiter requirements and range capability. Three representative vertical lift vehicles were developed to explore the tradeoff in capability between hover efficiency versus range and endurance capability. The vehicles were a single-main rotor helicopter, a tilt rotor, and a vertical take-off and landing (VTOL) aircraft. Vehicle capability was limited to two or three people (including pilot or crew) and maximum range within one hour of flight (100-200 miles, depending on vehicle). Two types of propulsion and energy storage systems were used in this study. First was traditional hydrocarbon-fueled cycles (such as Otto, diesel or gas turbine cycles). Second was an all-electric system using electric motors, power management and distribution, assuming batteries for energy storage, with the possibility of hydrocarbon-fueled range extenders. The high power requirements for hover significantly reduced mission radius capability. Loiter was less power intensive, resulting in about 1/2 the equivalent mission radius penalty. With so many design variables, the VTOL aircraft has the potential to perform well for a variety of missions. This vehicle is a good candidate for additional study; component model development is also required to adequately assess performance over the design space of interest.

systems analysis↗

NASA NTRS2016

Range and Endurance Tradeoffs on Personal Rotorcraft Design

Rotorcraft design has always been a challenging tradeoff among overall size, capabilities, complexity, and other factors based on available technology and customer requirements. Advancements in propulsion, energy systems and other technologies have enabled new vehicles and missions; complementary advances in analysis methods and tools enable exploration of these enhanced vehicles and the evolving mission design space. A system study was performed to better understand the interdependency between vehicle design and propulsion system capabilities versus hover loiter requirements and range capability. Three representative vertical lift vehicles were developed to explore the tradeoff in capability between hover efficiency versus range and endurance capability. The vehicles were a single-main rotor helicopter, a tilt rotor, and a vertical take-off and landing (VTOL) aircraft. Vehicle capability was limited to two or three people (including pilot or crew) and maximum range within one hour of flight (100-200 miles, depending on vehicle). Two types of propulsion and energy storage systems were used in this study. First was traditional hydrocarbon-fueled cycles (such as Otto, diesel or gas turbine cycles). Second was an all-electric system using electric motors, power management and distribution, assuming batteries for energy storage, with the possibility of hydrocarbon-fueled range extenders. The high power requirements for hover significantly reduced mission radius capability. Loiter was less power intensive, resulting in about 12 the equivalent mission radius penalty. With so many design variables, the VTOL aircraft has the potential to perform well for a variety of missions. This vehicle is a good candidate for additional study; component model development is also required to adequately assess performance over the design space of interest.

systems analysis↗

NASA NTRSDate not supplied

A Data-Driven Reduced Order Model of an Isolated Rotor

There are numerous conceptual design stage rotorcraft analysis tasks which demand a high-fidelity and low cost method for rotor load distribution predictions. Considering Urban Air Mobility (UAM) vehicles aim to operate in close proximity to buildings and with unique rotor configurations, there is a significant challenge in quickly and accurately modeling rotors operating in complex, turbulent flow fields. One potential path for deriving a high-fidelity, low cost rotor model is with data-driven surrogate modeling. In this study, an initial investigation is taken to apply a proper orthogonal decomposition (POD) based reduced order model (ROM) for the purpose of pressure distribution prediction. In this study, a POD ROM was derived to produce distributed pressure predictions on rotor blades subjected to topology change due to variation in twist and taper ratio. Rotor twist was varied between 0◦, 10◦, 20◦, and 30◦ while taper ratio was varied between 1.0, 0.9, 0.8, and 0.7. All rotors consisted of a single blade. The POD ROM was validated for three demonstration cases; a high thrust rotor in hover, a low thrust rotor in hover, and a rotor in forward flight with a flight speed of M = 0.1. Results showed highly accurate distributed load predictions could be achieved at minimal computational cost. Computational cost for hovering blade surface pressure modeling was reduced from 12 hours on 440 cores to 10−5 seconds on a single core. For blade in forward flight cost was reduced from 20 hours on 440 cores to 0.6 seconds on a single core. For cases of high thrust and low thrust rotors, POD ROM was used to undergo a design optimization of the rotor such that figure of merit was maximized. Total optimization time for each case was 1 minute.

Data-Driven↗

NASA NTRSDate not supplied

Novel Tilting Ducted-Fan Aerial Vehicle Configurations

There has been recent renewed interested in ducted-fan, powered-lift vertical takeoff and landing aircraft vehicles for uninhabited aerial vehicle and urban aerial mobility aerial applications. Early work was conducted in the 1950’s to the late 1980’s into ducted-fan vehicles, especially at the time for military missions. The focus of ducted-fan research began to shift to UAV’s and personal air transportation in the 2000’s. Work in the early 2000’s fostered interest into ducted-fan aerial vehicles for vertical lift planetary aerial vehicle missions, especially for missions to Titan, a moon of Saturn. For example, early work at NASA Ames conducted the first known investigation into oval ducts (with internal tandem fans) to be used for these aerial vehicles. The use of twin oval ducts (with internal tandem fans) allowed the use of quadrotor-style rotor rpm control for vehicle trim (in hover, for transition to high-speed forward flight the addition of a tilt-actuator to pitch the twin oval ducts forward to be aligned with the freestream needed to be added to the control approach. This current study explores open-rotor, single isolated ducted-fan, and full vehicle configuration aerodynamic performance for hover, transition, and cruise regimes for novel tilting ducted-fan aerial vehicle configurations. The objective of this study is to better understand the design aerodynamics trade space for noncircular tilting ducted-fans. The primary analysis tool used in this paper is the mid-fidelity computational fluid dynamics RotCFD tool. Several interesting and largely unexplored rotor-on-rotor (or fan-on-fan), duct-on-rotor, rotor- on-duct, and duct-on-airframe are examined in this paper. Many of these aerodynamic interactions are the key to overall aerial vehicle performance. Limited parametric sweeps of rotor-to-rotor spacing (and, therefore, sizing and shape of the enveloping ducts) for the various duct configurations will also be performed. The trade-offs between duct thrust augmentation in hover versus improved transition controllability versus improved cruise L/D will be discussed for various novel duct configurations. These ducted-fan configurations include oval ducts, ‘figure-eight’ ducts, and ‘B-shaped’ ducts, among others.

Ducted-Fan↗

NASA NTRSDate not supplied

Assessing Helicopter Pilots’ Detect and Avoid and Collision Avoidance Performance With ACAS Xr

The latest variant of the Federal Aviation Administration’s Airborne Collision Avoidance System (ACAS X) is being designed for both crewed and uncrewed rotorcraft. Referred to as ACAS Xr, the system joins a suite of other ACAS X variants poised to replace the Traffic Alert and Collision Avoidance System (TCAS II). ACAS Xr is tuned to support current-day helicopter platforms as well as electric Vertical Takeoff and Landing (eVTOL) vehicles that are still under development. Given this flexibility, ACAS Xr may be used by helicopter crews currently in operation or by remotely-operated eVTOL aircraft in the emerging Advanced Air Mobility (AAM) market. To cover the range of potential uses, two distinct configurations are being proposed for ACAS Xr: Collision Avoidance System (CAS) and Detect and Avoid (DAA). Under the CAS configuration, ACAS Xr provides minimal caution-level alerting but issues directive warning-level alerting and guidance. The DAA configuration, by contrast, provides caution-level alerting and guidance, in addition to the warning-level alerting and guidance. The current study was performed as part of the National Aeronautics and Space Administration’s AAM project. Six helicopter pilots were recruited to fly a variety of scripted traffic scenarios in a full-motion, crewed eVTOL simulator. Participants flew 60 encounters over two days, reacting to pre-recorded intruder aircraft that were scripted to fly into the participant’s aircraft from different approach angles, relative altitudes, and during different phases of flight. The pilots flew half of the encounters with the CAS configuration and half with the DAA configuration. Within each block of 30 encounters, pilots experienced 10 conflicts while in cruise, 10 in hover, and 10 while on approach to a heliport. Results showed that pilot response times were consistently under 5 seconds for RAs and under 10 seconds for DAA alerts, when present, during all three phases of flight. Unsurprisingly, the DAA configuration was associated with lower rates of en-route and high-severity losses of DAA well clear compared to the CAS configuration in all phases of flight except for the terminal area. Rates of losses of DAA well clear were found to be substantially higher in the Hover scenario, compared to Cruise. Pilots failed to fully comply with RAs at a rate of 0.10-0.18 in all conditions except for the DAA configuration in the Hover scenario, which was associated with a higher non-compliance rate of 0.4 due to Descend RAs issued at low altitudes. The implications of these results with regards to the ongoing development of ACAS Xr is discussed.

air taxis↗

NASA NTRSDate not supplied

Assessing Helicopter Pilots’ Detect and Avoid and Collision Avoidance Performance with ACAS Xr

The latest variant of the Federal Aviation Administration’s Airborne Collision Avoidance System (ACAS X) is being designed for both crewed and uncrewed rotorcraft. Referred to as ACAS Xr, the system joins a suite of other ACAS X variants poised to replace the Traffic Alert and Collision Avoidance System (TCAS II). ACAS Xr is tuned to support current-day helicopter platforms as well as electric Vertical Takeoff and Landing (eVTOL) vehicles that are still under development. Given this flexibility, ACAS Xr may be used by helicopter crews currently in operation or by remotely-operated eVTOL aircraft in the emerging Advanced Air Mobility (AAM) market. To cover the range of potential uses, two distinct configurations are being proposed for ACAS Xr: Collision Avoidance System (CAS) and Detect and Avoid (DAA). Under the CAS configuration, ACAS Xr provides minimal caution-level alerting but issues directive warning-level alerting and guidance. The DAA configuration, by contrast, provides caution-level alerting and guidance, in addition to the warning-level alerting and guidance. The current study was performed as part of the National Aeronautics and Space Administration’s AAM project. Six helicopter pilots were recruited to fly a variety of scripted traffic scenarios in a full-motion, crewed eVTOL simulator. Participants flew 60 encounters over two days, reacting to pre-recorded intruder aircraft that were scripted to fly into the participant’s aircraft from different approach angles, relative altitudes, and during different phases of flight. The pilots flew half of the encounters with the CAS configuration and half with the DAA configuration. Within each block of 30 encounters, pilots experienced 10 conflicts while in cruise, 10 in hover, and 10 while on approach to a heliport. Results showed that pilot response times were consistently under 5 seconds for RAs and under 10 seconds for DAA alerts, when present, during all three phases of flight. Unsurprisingly, the DAA configuration was associated with lower rates of en-route and high-severity losses of DAA well clear compared to the CAS configuration in all phases of flight except for the terminal area. Rates of losses of DAA well clear were found to be substantially higher in the Hover scenario, compared to Cruise. Pilots failed to fully comply with RAs at a rate of 0.10-0.18 in all conditions except for the DAA configuration in the Hover scenario, which was associated with a higher non-compliance rate of 0.4 due to Descend RAs issued at low altitudes. The implications of these results with regards to the ongoing development of ACAS Xr is discussed.

air taxis↗

NASA NTRSDate not supplied

Helicopter Pilot Evaluations of the Airborne Collision Avoidance System Xr in a High-Fidelity Motion Simulation

New aircraft and aerial Urban Air Mobility operations require updated technologies to maintain vehicle separation during flight. Specifically, higher-density airspace will need more than traditional air traffic control to keep vehicles well clear of each other and avoid Near Midair Collisions. In response, the Federal Aviation Administration is currently developing the Airborne Collision Avoidance System X (ACAS X) for next-generation air traffic deconfliction, which provides caution-level and warning-level alerts in response to multiple aircraft types. This study recruited six helicopter pilots to fly an electric vertical takeoff and landing vehicle model in simulated operations under Visual Flight Rules (VFR). Flights were accomplished using the high-fidelity Vertical Motion Simulator at the NASA Ames Research Center. Participants controlled the vehicle using two side inceptors and foot rudders. The rotorcraft variant of ACAS X (ACAS Xr) was provided for alerting and guidance during traffic conflicts. Pilots used this system while giving feedback to the researchers through questionnaires, debriefs, and other discussions. Variables of interest to the study were phases of flight (i.e., Cruise, Hover, and Approach) and ACAS Xr configurations: The Collision Avoidance System configuration behaves similarly to current commercial traffic systems used for tactical deconfliction in crewed vehicles, and the Detect and Avoid configuration was developed to provide extra, corrective-level guidance for unmanned aircraft systems. Results showed that pilots found the alerting and guidance from ACAS Xr useful, effective, and acceptable for VFR operations. Certain elements, like speed guidance and text banners, were found to be of no use to the pilots. Hover and Approach scenarios were considered the most difficult for ACAS Xr alerting. Reasons for this difficulty were partially due to learning interference (i.e., overcoming previously learned behavior) and partially due to the vehicle model (i.e., NASA’s Lift Plus Cruise design). Still, alerting-based confounds reveal the need for more development for ACAS Xr during these Hover and Approach flight phases. Study caveats and future projects are discussed.

air taxis↗

NASA NTRSDate not supplied

Helicopter Pilot Evaluations of the Airborne Collision Avoidance System Xr in a High-Fidelity Motion Simulation

New aircraft and aerial Urban Air Mobility operations require updated technologies to maintain vehicle separation during flight. Specifically, higher-density airspace will need more than traditional air traffic control to keep vehicles well clear of each other and avoid Near Midair Collisions. In response, the Federal Aviation Administration is currently developing the Airborne Collision Avoidance System X (ACAS X) for next-generation air traffic deconfliction, which provides caution-level and warning-level alerts in response to multiple aircraft types. This study recruited six helicopter pilots to fly an electric vertical takeoff and landing vehicle model in simulated operations under Visual Flight Rules (VFR). Flights were accomplished using the high-fidelity Vertical Motion Simulator at the NASA Ames Research Center. Participants controlled the vehicle using two side inceptors and foot rudders. The rotorcraft variant of ACAS X (ACAS Xr) was provided for alerting and guidance during traffic conflicts. Pilots used this system while giving feedback to the researchers through questionnaires, debriefs, and other discussions. Variables of interest to the study were phases of flight (i.e., Cruise, Hover, and Approach) and ACAS Xr configurations: The Collision Avoidance System configuration behaves similarly to current commercial traffic systems used for tactical deconfliction in crewed vehicles, and the Detect and Avoid configuration was developed to provide extra, corrective-level guidance for unmanned aircraft systems. Results showed that pilots found the alerting and guidance from ACAS Xr useful, effective, and acceptable for VFR operations. Certain elements, like speed guidance and text banners, were found to be of no use to the pilots. Hover and Approach scenarios were considered the most difficult for ACAS Xr alerting. Reasons for this difficulty were partially due to learning interference (i.e., overcoming previously learned behavior) and partially due to the vehicle model (i.e., NASA’s Lift Plus Cruise design). Still, alerting-based confounds reveal the need for more development for ACAS Xr during these Hover and Approach flight phases. Study caveats and future projects are discussed.

air taxis↗

NASA NTRSDate not supplied

Analytical Flight Dynamic Model Development for eVTOL Aircraft

This paper presents an analytical flight dynamic model development method for a multi- rotor eVTOL aircraft in hover and transition flight. The method captures the analytical stability and control sensitivities of rotor unsteady aerodynamic loads about a trim solution generated by a rotorcraft aeromechanics comprehensive analysis tool. The rotor aerody- namic forces include circulatory and non-circulatory components to account for unsteady aerodynamics. The circulatory forces are corrected for unsteady aerodynamics using the time-domain approximation of Theodorsen’s function. The integrated flight dynamic model includes the rigid-body aircraft flight dynamics, inflow dynamics, unsteady aerodynamics, and blade pitch and rotor actuator dynamics. Stability analyses shows that the Lift+Cruise aircraft is statically unstable in roll and yaw axes and also dynamically unstable in hover. Closed-loop feedback control is necessary for stable hover flight.

rotorcraft↗

DOE OSTI2017

Purpose-Built UAVs for Physical Sampling of Trace Contamination at the Portsmouth Gaseous Diffusion Plant - 17331

The sampling of trace amounts of contamination, particularly of low-energy byproducts such as americium, presents a challenge for non-contact sensing. In many cases, such as determining the need for cleaning inside the exhaust shaft of the Waste Isolation Pilot Plant or sampling the walls of the enormous Gaseous Diffusion Plant at Portsmouth, it may be desirable to take physical swab samples at carefully distributed sample locations for analysis by mass spectrometry. Because of the danger posed to human workers in such scenarios, including risk of falls from lethal heights and exposure to low levels of radiation and the hassle of donning and doffing PPE, a low-cost robotic solution is desired. The inaccessibility of the heights involved suggest Unmanned Aerial Vehicle (UAV) solutions, rather than Unmanned Ground Vehicle (UGV) solutions, but conventional quadrotor UAVs are ill-suited to precise physical interaction with their surroundings. Quadrotors are under-actuated, rendering them non-holonomic and preventing the dexterous application of arbitrary generalized force/torques in interaction with the environment. At Purdue University, the authors have developed a number of novel UAV platforms suitable for dexterous interaction with the environment, making them ideal for such applications. These platforms can independently control forces in all directions, allowing for controlled application of the swab to the surface. Because of the scale of these structures (over 2 km in the case of the Gaseous Diffusion Plant), flight efficiency is of supreme importance. The Purdue team is took a variety of vehicles to the Gaseous Diffusion Plant for field trials on site in August, 2016. (With results available prior to the meeting.) The Purdue Dexterous Hexrotor is a fully-actuated Hexrotor capable of exerting forces in all six directions of force and torque. Operating alone or in swarms, the Dexterous Hexrotor can fly in free space, transition to contact through impact control, and sample the surface through force control. The Purdue I-BoomCopter is a tri-copter with an extra horizontal propeller that enables long-distance flight without pitching and the ability to apply closed-loop forces horizontally. Finally, the Purdue Tiltrotor VTOL is an under-actuated hybrid UAV that combines tilting rotors for vertical takeoff and landing, with a fixed-wing, flying-body design that is ultra-efficient for long-distance flight. The Dexterous Hexrotor provided two demonstrations of physical sampling of walls and crane rails. In sampling the large open sections of the inside of the plant, a small swarm of three UAVs is commanded to sample three distinct points on an internal map of the building. Human-supervised autonomy permits the UAVs to take off by themselves, find a clear elevation at which to fly through uncluttered space, navigate to their designated sampling points, and pause for confirmation by the human supervisor. The supervisor is presented with a video image of the intended sampling spot, which, if confirmed, the UAV will automatically approach and sample. The UAVs then autonomously return to the take-off spot. The second demo involved a single UAV searching upwards, then transitioning into 3-D SLAM mode to wait for a safe sampling spot on the 3-D scan to acquire the sample from the crane rail. The human supervisor, in this case, is responsible for ensuring the absence of cables and other obstacles. I-BoomCopter demonstrated its high-speed, long-distance coverage ability by making a few fast passes before homing in on a mock-up electrical panel with door, which it opened and closed. The dexterity of the I-BoomCopter results from its large propellers, which allow for controlled hovering and the horizontal thruster for applying forces of significant magnitude. Finally, the Tiltrotor VTOL is highly efficient in fixed-wing mode, but the tilt-rotor is under-actuated in hover. The tilt-rotor will take off vertically, then transition to high-speed, long-distance flight to make a number of passes inside the facility. The significance of these demos is the low-cost implementation of physical sampling over prescribable locations in difficult-to-reach areas of potentially contaminate facilities. To make this tractable over very large facilities, the demonstration of combinations of dexterous hovering ability and long-distance/high-speed flight is also in evidence. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗