Search NASA⌕ Search

SEARCH · Search NASA

Results for “interdiffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Performance of Al-rich Oxidation Resistant Coatings for Fe-Base Alloys

Aluminum-rich coatings made by chemical vapor deposition and pack cementation on ferritic (e.g. Fe-9Cr-1Mo) and austenitic (Type 304L) substrates are being evaluated at 650-800 C. For oxidation testing, a humid air environment was used to quantify coating performance, as uncoated substrates experience rapid oxidation at these temperatures. A main goal of this work is to demonstrate the potential benefits and problems with alumina-forming coatings. The higher exposure temperatures were selected to accelerate the degradation of the coating by interdiffusion with the substrate. A general conclusion of this testing was that coatings with less Al and a ferritic Fe(Al) structure could be more durable than higher Al content aluminide coatings which have a large thermal expansion mismatch with these substrates. A lifetime model has been developed using diffusion and oxidation observations to predict coating performance as a function of temperature and initial coating composition. To test and improve the model, additional experiments are now being conducted to determine the effect of substrate composition (e.g. Cr content using Fe-12Cr and Fe-9Cr-2W substrates) and exposure temperature on the critical Al content for coating failure. Because of the unexpectedly low level of Al measured at coating failure ({approx}3.5 at.% at 700 C), exposures of specimens with thick ({approx}200 {micro}m) high Al content coatings were stopped after 10kh at 800 C and 20kh at 700 C because extremely long times to failure were predicted. Post-exposure Al concentration profiles for these specimens were measured using electron microprobe.

36 MATERIALS SCIENCE↗

Interfacial Widths of Conjugated Polymer Bilayers

The interfaces of conjugated polyelectrolyte (CPE)/poly[2-methoxy-5-(2{prime}-ethylhexyloxy)-p-phenylene vinylene] (MEH-PPV) bilayers cast from differential solvents are shown by resonant soft X-ray reflectivity (RSoXR) to be very smooth and sharp. The chemical interdiffusion due to casting is limited to less than 0.6 nm, and the interface created is thus nearly 'molecularly' sharp. These results demonstrate for the first time and with high precision that the nonpolar MEH-PPV layer is not much disturbed by casting the CPE layer from a polar solvent. A baseline is established for understanding the role of interfacial structure in determining the performance of CPE-based polymer light-emitting diodes. More broadly, we anticipate further applications of RSoXR as an important tool in achieving a deeper understanding of other multilayer organic optoelectronic devices, including multilayer photovoltaic devices.

36 MATERIALS SCIENCE↗

CdS/CdTe Solar Cells Containing Directly Deposited CdSxTe1-x Alloy Layers: Preprint

A CdSxTe1-x layer forms by interdiffusion of CdS and CdTe during the fabrication of thin-film CdTe photovoltaic (PV) devices. The CdSxTe1-x layer is thought to be important because it relieves strain at the CdS/CdTe interface that would otherwise exist due to the 10% lattice mismatch between these two materials. Our previous work [1] has indicated that the electrical junction is located in thisinterdiffused CdSxTe1-x region. Further understanding, however, is essential to predict the role of this CdSxTe1-x layer in the operation of CdS/CdTe devices. In this study, CdSxTe1-x alloy films were deposited by radio-frequency (RF) magnetron sputtering and co-evaporation from CdTe and CdS sources. Both RF-magnetron-sputtered and co-evaporated CdSxTe1-x films of lower S content (x<0.3) have acubic zincblende (ZB) structure akin to CdTe, whereas those of higher S content have a hexagonal wurtzite (WZ) structure like that of CdS. Films become less preferentially oriented as a result of a CdCl2 heat treatment (HT) at~400 degrees C for 5 min. Films sputtered in a 1% O2/Ar ambient are amorphous as deposited, but show CdTe ZB, CdS WZ, and CdTe oxide phases after a CdCl2 HT. Filmssputtered in O2 partial pressure have a much wider bandgap than expected. This may be explained by nanocrystalline size effects seen previously [2] for sputtered oxygenated CdS (CdS:O) films. Initial PV device results show that the introduction of a directly-deposited CdSxTe1-x alloy layer into the device structure produces devices of comparable performance to those without the alloy layer whena CdCl2 HT is performed. Further investigation is required to determine whether the CdCl2 heat treatment step can be altered or eliminated through direct deposition of the alloy layer.

14 SOLAR ENERGY↗

The Miscibility and Depth Profile of PCBM in P3HT: Thermodynamic Information to Improve Organic Photovoltaics

Recent work has shown that poly(3-hexylthiophene) (P3HT) and the surface functionalized fullerene 1-(3-methyloxycarbonyl)propy(1-phenyl [6,6]) C61 (PCBM) are much more miscible than originally thought, and the evidence of this miscibility requires a return to understanding the optimal morphology and structure of organic photovoltaic active layers. This manuscript describes the results of experiments that were designed to provide quantitative thermodynamic information on the miscibility, interdiffusion, and depth profile of P3HT:PCBM thin films that are formed by thermally annealing initial bilayers. It is found that the resultant thin films consist of a bulk layer that is not influenced by the air or substrate surface. The composition of PCBM in this bulk layer increases with increased PCBM loading in the original bilayer until the bulk layer contains 22 vol% PCBM. The introduction of additional PCBM into the sample does not increase the amount of PCBM dispersed in this bulk layer. This observation is interpreted to indicate that the miscibility limit of PCBM in P3HT is 22 vol%, while the precise characterization of the depth profiles in these films shows that the PCBM selectively segregates to the silicon and near air surface. The selective segregation of the PCBM near the air surface is ascribed to an entropic driving force.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Superconductivity in La1.56Sr0.44CuO4/La2CuO4 Superlattices

Superlattices of the repeated structure La{sub 1.56}Sr{sub 0.44}CuO{sub 4}/La{sub 2}CuO{sub 4} (LSCO-LCO), where none of the constituents is superconducting, show a superconducting transition of T{prime}{sub c} 25 K. In order to elucidate the nature of the superconducting state we have performed a low-energy {mu}SR study. By applying a magnetic field parallel (Meissner state) and perpendicular (vortex state) to the film planes, we could show that superconductivity is sheet like, resulting in a very anisotropic superconducting state. This result is consistent with a simple charge-transfer model, which takes into account the layered structure and the difference in the chemical potential between LCO and LSCO, as well as Sr interdiffusion. Using a pancake-vortex model we could estimate a strict upper limit of the London penetration depth to 380 nm in these superlattices. The temperature dependence of the muon depolarization rate in field cooling experiments is very similar to what is observed in intercalated BSCCO and suggests that vortex-vortex interaction is dominated by electromagnetic coupling but negligible Josephson interaction.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Magnetism reflectometer study shows LiF layers improve efficiency in spin valve devices

New, more efficient materials for spin valves - a device used in magnetic sensors, random access memories, and hard disk drives - may be on the way based on research using the magnetism reflectometer at Oak Ridge National Laboratory (ORNL). Spin valve devices work by means of two or more conducting magnetic material layers that alternate their electrical resistance depending on the layers alignment. Giant magnetoresistance is a quantum mechanical effect first observed in thin film structures about 20 years ago. The effect is observed as a significant change in electrical resistance, depending on whether the magnetization of adjacent ferromagnetic layers is in a parallel or an antiparallel magnetic alignment. 'What we are doing here is developing new materials. The search for new materials suitable for injecting and transferring carriers with a preferential spin orientation is most important for the development of spintronics,' said Valeria Lauter, lead instrument scientist on the magnetism reflectometer at the Spallation Neutron Source (SNS), who collaborated on the experiment. The researchers discovered that the conductivity of such materials is improved when an organic polymer semiconductor layer is placed between the magnetic materials. Organic semiconductors are now the material of choice for future spin valve devices because they preserve spin coherence over longer times and distances than conventional semiconductors. While research into spin valves has been ongoing, research into organic semiconductors is recent. Previous research has shown that a 'conductivity mismatch' exists in spin valve systems in which ferromagnetic metal electrodes interface with such organic semiconductors as Alq3 ({pi}-conjugated molecule tris(8-hydroxy-quinoline) aluminium). This mismatch limits the efficient injection of the electrons from the electrodes at the interface with the semiconductor material. However, lithium fluoride (LiF), commonly used in light-emitting diodes, has been found to enhance the injection of electrons through the semiconductor. Researchers from the University of Alabama and ORNL used polarized neutrons at the magnetism reflectometer at SNS to investigate the electronic, magnetic, and structural properties of the electrodes in a novel system. In this system, the magnetic layers cobalt and Ni{sub 80}Fe{sub 20} are interfaced with spacer layers composed of the organic semiconductor Alq3. A coupling layer of LiF is inserted to separate the magnetized layers from the semiconductor. 'ALQ3 is an organic semiconductor material,' said Lauter. 'Normally in these systems a first magnetic layer is grown on a hard substrate so that one can get the controlled magnetic parameters. Then you grow the organic semiconductor layer, followed by another magnetic material layer, such as cobalt.' In addition to determining the effect of the LiF layers on the efficiency of the electron injection, the researchers wanted to determine the magnetic properties of the cobalt and Ni{sub 80}Fe{sub 20} as well as the interfacial properties: whether there is interdiffusion of cobalt through the LiF layer to the semiconductor, for example. The researchers used polarized neutrons at beam line 4A to probe the entire, layer-by-layer assembly of the system. 'Reflectometry with polarized neutrons is a perfect method to study thin magnetic films,' Lauter said. 'These thin films - if you put one on a substrate, you see it just like a mirror. However, this mirror has a very complicated internal multilayer structure. The neutrons look inside this complicated structure and characterize each and every interface. Due to the depth sensitivity of the method, we measure the structural and magnetic properties of each layer with the resolution of 0.5 nm. The neutron scattering results found that inserting LiF as a barrier significantly improves the quality of the interface, increasing the injection of electrons from the magnetic layer through the organic semiconductor in the spin valve and enhancing the overall properties of the system. In related work the magnetic properties of the cobalt film and the permalloy Ni{sub 80}Fe{sub 20} were characterized. Cobalt in particular needed attention, as it cannot be grown epitaxially (i.e., deposited) on an organic semiconductor film. Cobalt becomes polycrystalline or amorphous, and this affects its magnetic properties. The data from the first experiment showed that the cobalt layer in the system 'did not have typical magnetic properties,' Lauter said. 'The results showed that the cobalt had low magnetization. To improve the efficiency, the cobalt magnetization should be much higher. So this experiment helped us to improve the growth conditions and to get a cobalt layer with better magnetic properties.' In a subsequent experiment the researchers increased the magnetization of the cobalt, and a follow-up paper is in progress.

36 MATERIALS SCIENCE↗

Full-length U-xPu-10Zr (x=0, 8, 19 wt%) Fast Reactor Fuel Test in FFTF

The Integral Fast Reactor-1 (IFR-1) experiment performed in the Fast Flux Test Facility (FFTF) was the only U-Pu-10Zr (Pu-0, 8 and 19 wt%) metallic fast reactor test with commercial-length (91.4 cm active fuel column length) conducted to date. With few remaining test reactors there is little opportunity for performing another test with a long active fuel column. The assembly was irradiated to the goal burnup of 10 at.%. The beginning of life (BOL) peak cladding temperature of the hottest pin was 608?C, cooling to 522?C at end of life (EOL). Selected fuel pins were examined non destructively using neutron radiography, precision axial gamma scanning, and both laser and spiral contact cladding profilometry. Destructive exams included plenum gas pressure, volume, and gas composition determinations on a number of pins followed by optical metallography, electron probe microanalysis (EPMA), and alpha and beta gamma autoradiography on a single U-19Pu-10Zr pin. The post-irradiation examinations (PIEs) showed very few differences compared to the short-pin (34.3 cm fuel column) testing performed on fuels of similar composition in Experimental Breeder Reactor-II (EBR-II). The fuel column grew axially slightly less than observed in the short pins, but with the same pattern of decreasing growth with increasing Pu content. There was a difference in the fuel-cladding chemical interaction (FCCI) in that the maximum cladding penetration by interdiffusion with fuel/fission products did not occur at the top of the fuel column where the cladding temperature is highest, as observed in EBR-II tests. Instead, the more exaggerated fission-rate profile of the FFTF pins resulted in a peak FCCI at ~0.7 X/L axial location along the fuel column. This resulted from a lower production of rare earth fission products higher in the fuel column as well as a much smaller delta-T between fuel center and cladding, and therefore less FCCI, despite the higher cladding temperature. This behavior could actually help extend the life of a fuel pin in a “long pin” reactor design to a higher peak fuel burnup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Nanocrystalline cerium oxide materials for solid fuel cell systems

Disclosed are solid fuel cells, including solid oxide fuel cells and PEM fuel cells that include nanocrystalline cerium oxide materials as a component of the fuel cells. A solid oxide fuel cell can include nanocrystalline cerium oxide as a cathode component and microcrystalline cerium oxide as an electrolyte component, which can prevent mechanical failure and interdiffusion common in other fuel cells. A solid oxide fuel cell can also include nanocrystalline cerium oxide in the anode. A PEM fuel cell can include cerium oxide as a catalyst support in the cathode and optionally also in the anode.

30 DIRECT ENERGY CONVERSION↗

Nuclear fuel development based on UMo alloys under irradiation evaluation of LEU U{sub 3}Si{sub 2} - 4.8 gU/cm{sup 3} test fuel

Latest irradiation reports on UMo dispersion fuel demand different solutions in order to stabilize an undesirable interaction layer zone produced by chemical reactions with the standard Al matrix. Among the different solutions, this paper addresses the evaluation of the additions of Si to the Al matrix and/or small amount of tetravalent elements (Si, Zr and Ti) to the fuel. The results of out-of-pile swelling tests applied to dispersion mini plates made of these modified constituents and interaction tests of interdiffusion couples are discussed. These results shows that the volume changes are directly related with the uranium density. The unmodified UMo/Al system exhibited swelling levels almost three times higher than those achieved with U{sub 3}Si{sub 2}, however for the system UMo/AlSi mix, these undesired behavior was reduced to values equivalent or slightly lower than U{sub 3}Si{sub 2}. Finally, details and specifications of a LEU U{sub 3}Si{sub 2} 4,8 gU/cm{sup 3} test fuel element, fabricated for under irradiation evaluation and design validation purposes at the RECH-1 research reactor, are reported in this paper. The planned follow-up program and initial irradiation results showing an appropriate performance that allows reaching the expected {sup 235}U burn up level, slightly over 50%, are detailed and discussed in next pages. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Two types of diffusions at the cathode/electrolyte interface in IT-SOFCs

Analytical transmission electron microscopy, in particular with the combination of energy dispersive X-ray spectroscopy (EDX) and electron energy-loss spectroscopy (EELS), has been performed to investigate the microstructure and microchemistry of the interfacial region between the cathode (La{sub 0.6}Sr{sub 0.4}Co{sub 0.8}Fe{sub 0.2}O{sub 3}, LSCF) and the electrolyte (Gd-doped ceria, GDC). Two types of diffusions, mutual diffusion between cathode and electrolyte as well as the diffusion along grain boundaries, have been clarified. These diffusions suggest that the chemical stability of LSCF and GDC are not as good as previously reported. The results are more noteworthy if we take into consideration the fact that such interdiffusions occur even during the sintering process of cell preparation. - Graphical Abstract: Two types of diffusions, the mutual diffusion and the diffusion along grain boundaries, occurred at the cathode/electrolyte interface of intermediate temperature solid state fuel cells, during cell preparation. The mutual diffusion is denoted by black arrows and the diffusion along grain boundaries assigned by pink arrows. Highlights: > All the cations in cathode (LSCF) and electrolyte (GDC) can mutually diffuse into each other. > Diffusing elements will segregate at grain boundaries or triple junctions around the cathode/electrolyte interface. > Two types of diffusions, the mutual diffusion and diffusion along grain boundaries, have been clarified thereafter.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Role of Electron and Atom Probe Tomography in Characterization of Nuclear Fuels

Dramatic advances in materials characterization capabilities over the last few years enabled microstructural and chemical 3D characterization of specimens at the atomic-scale with unprecedented quantitative precision and high data collection rates. These improvements allow for the transition of electron tomography (ET) and atom probe tomography (APT) techniques to a much broader research field and their implementation in the characterization of nuclear fuels and highly radioactive materials. Nanoscale characterization has been widely developed for non-nuclear applications, yet in the nuclear arena, particularly for fuels, these modern characterization techniques have not been applied in concert to elucidate fundamental material behavior in metal fuel. In this work, we present cross-correlated APT and ET data and provide atomic-scale representations of microstructure and chemistry of nuclear fuels, which is essential in the validation of current and future atomistic and meso-scale modeling efforts. A firm understanding of microstructural evolution in reactor materials is imperative and will lead to deeper understanding of in-reactor degradation behavior, creating a new generation of radiation-resistant materials and fuels with the potential for significant increases in burn-up. In summary, two complementary techniques were used to characterize phases formed as a result of interdiffusion between U-Pu-Zr metal fuel and cladding and fission gas bubbles produced in U-Mo fuel upon irradiation. Understanding in-reactor degradation behavior of these materials is critical to advancing nuclear energy technology. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TEM Characterization of U-Mo Irradiated with High-Energy Xe Ions

U-Mo alloys (with 7-10 wt.% Mo) with a low U-235 enrichment (< 20%) have been developed to be used in high-performance research and test reactors, replacing the current highly enriched uranium (HEU) fuels. A number of in-pile irradiation tests of U-Mo fuels show that drastic microstructural changes occurred during reactor irradiation, including the formation of U-Mo-Al interaction products and large gas-filled pores. These microstructural changes might lead to breakaway swelling and deterioration of plate mechanical integrity. Hence, it is critical to understand the underlying mechanisms of these microstructural changes in order to improve the irradiation behavior of UMo fuels. Heavy ion irradiation was employed in this study to investigate separate effects of the irradiation behavior of U-Mo fuels. 1.7 mm diameter disks punched out from UMo/ Al dispersion fuel mini-plates were irradiated with 84 MeV Xe ions at the ATLAS accelerator at Argonne National Laboratory (ANL). This particular ion source was selected for two reasons: (1) to simulate the irradiation response of the fuel to fission fragment bombardments, and (2) to study fission gas behavior, as fission gas bubble formation and growth is the primary cause of U-Mo fuel swelling. The ion-irradiated samples have been characterized with scanning electron microscopy (SEM). This study focuses on the characterization of the samples using transmission electron microscopy (TEM). With the high magnification details, microstructures in U-Mo along the ion penetration depth were revealed. The U-7Mo/Al dispersion fuel sample irradiated with 84 MeV Xe ions to a dose of 2.9 x 10{sup 17} ions/cm{sup 3} was characterized using TEM. The TEM results exhibit that the sample microstructure varies along the ion penetration depth. Near the sample surface (zone A) is a layer of nano-crystalline U-Mo-Al interdiffusion product. After passing through zone A, the Xe ions resided in zone B, where gas bubbles formed in U-Mo. TEM images of this region displayed that large gas bubbles formed on grain boundaries and high-density nano-bubbles lay inside grains. The random distribution of intragranular bubbles indicates that the irradiation conditions of this sample cannot lead to gas bubble superlattice formation. Outside of the Xe penetration depth (zone C), significant amount of α-uranium precipitates were identified. The fact that no α-uranium precipitates were found in zone B suggests that the dose rate in this irradiation is sufficient to facilitate a phase reversal by means of a displacement spike mechanism. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of Interaction Layer and U-Mo Size on Pore Growth in U-Mo/Al Fuel

U-Mo/Al dispersion fuel, composed of U-Mo alloy fuel particles embedded in the aluminum (Al) matrix, has been developed to convert high-enriched uranium fuel to low-enriched uranium for high-performance research reactors. The fueled zone, referred to as 'fuel meat,' is clad with aluminum alloy. Fuel meat and cladding are metallurgically bonded during fabrication. Irradiated U-Mo/Al dispersion fuel has shown stable performance in low fission rate and burnup ranges. However, excessive fuel meat swelling or breakaway swelling, which is believed an incipient failure, was observed at higher fission rate and burnup conditions. This breakaway swelling is believed to be a result from the combination of accelerated fuel swelling and interconnection of large pores formed outside of the UMo particles. These large pores were frequently found, particularly, at the interface between the Al and the fuel-matrix interaction layer (IL) that formed by irradiation-enhanced interdiffusion of U-Mo and Al. Kim et al. developed a model for pore growth using a mechanical equilibrium between gas pressure in the pore, interfacial energies, and the external stress at the pore surface. In this model, IL provides a path way for fission gas to reach the pores and also generates tensile stress fields. Hence, suppressing IL growth by applying a diffusion barrier, like a coating of the U-Mo particles, appears to be an effective method to prevent pore formation. Another remedy to prevent pore formation is to use large U-Mo fuel particles. Using larger U-Mo particles was thought advantageous because it reduces fission gas release. In this study, the effect of IL growth and U-Mo particle size on pore formation is examined using the model. The advantage was quantified in terms of porosity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Oxide-nitride heteroepitaxy for low-loss dielectrics in superconducting quantum circuits

Superconducting qubits show great promise for the realization of fault-tolerant quantum computing, but lossy, amorphous dielectrics limit current technology. Identifying highly crystalline and stoichiometric dielectrics with intrinsically low microwave loss is therefore a central materials challenge, yet experimentally validated platforms remain scarce. In this work, we integrate a crystalline dielectric into a heteroepitaxial TiN/$γ$-Al$_2$O$_3$/TiN trilayer grown via pulsed laser deposition. Correlative high-resolution imaging, diffraction, and spectroscopy measurements confirm the single-crystal quality and chemical integrity of all layers, with minimal defects and limited anion interdiffusion across the oxide-nitride interfaces. Using microwave lumped-element resonators with parallel-plate capacitors, we report the first direct measurement of the dielectric loss of epitaxial $γ$-Al$_2$O$_3$, for which we find a low intrinsic two-level system loss, $δ_{\text{TLS}}^0 = (2.8 \pm 0.1) \times 10^{-5}$. These results establish heteroepitaxial oxides on transition metal nitrides as an attractive materials platform for superconducting quantum circuits, particularly for integration into compact device architectures such as merged-element transmons and microwave kinetic inductance detectors.

Garcia-Wetten, David A. [Northwestern U.]↗

Liquid-liquid interfaces of semifluorinated alkane diblock copolymers with water, alkanes, and perfluorinated alkanes.

The liquid-liquid interface between semifluorinated alkane diblock copolymers of the form F3C(CF2)n-1-(CH2)m-1CH3 and water, protonated alkanes, and perfluorinated alkanes are studied by fully atomistic molecular dynamics simulations. A modified version of the OPLS-AA (Optimized Parameter for Liquid Simulation All-Atom) force field of Jorgensen et al. has been used to study the interfacial behavior of semifluorinated diblocks. Aqueous interfaces are found to be sharp, with correspondingly large values of the interfacial tension. Due to the reduced hydrophobicity of the protonated block compared to the fluorinated block, hydrogen enhancement is observed at the interface. Water dipoles in the interfacial region are found to be oriented nearly parallel to the liquid-liquid interface. A number of protonated alkanes and perfluorinated alkanes are found to be mutually miscible with the semifluorinated diblocks. For these liquids, interdiffusion follows the expected Fickian behavior, and concentration-dependent diffusivities are determined.

08 HYDROGEN↗

Development of membranes for hydrogen separation: Pd-coated V-10Pd

Numerous Group IVB and VB alloys were prepared and tested as potential membrane materials but most of these materials were brittle or exhibited cracking during hydrogen exposure. One of the more ductile alloys, V-10Pd (at. %), was fabricated into a thin (107-{micro}m thick) composite membrane coated with 100 nm of Pd on each side. The material was tested for hydrogen permeability, resistance to hydrogen embrittlement, and long term hydrogen flux stability. The hydrogen permeability, {phi}, of the V-10Pd membrane was 3.86 x 10{sup -8} mol H{sub 2} m{sup -1} s{sup -1} Pa{sup -0.5} (avg. of three different samples) at 400 C, which is slightly higher than the permeability of Pd-23Ag at that temperature. A 1400 h hydrogen flux test at 400 C demonstrated that the rate of metallic interdiffusion was slow between the V-10Pd foil and the 100-nm-thick Pd coating on the surface. However, at the end of testing the membrane cracked at 118 C because of hydrogen embrittlement.

08 HYDROGEN↗

Performance of Al-Rich Oxidation Resistant Coatings for Fe-Base Alloys

Aluminum-rich coatings made by chemical vapor deposition and pack cementation on ferritic (e.g. Fe-9Cr-1Mo) and austenitic (Type 304L) substrates are being evaluated at 650-800 C. For oxidation testing, a humid air environment was used to quantify coating performance, as uncoated substrates experience rapid oxidation at these temperatures. A main goal of this work is to demonstrate the potential benefits and problems with alumina-forming coatings. The higher exposure temperatures were selected to accelerate the degradation of the coating by interdiffusion with the substrate. A general conclusion of this testing was that coatings with less Al and a ferritic Fe(Al) structure could be more durable than higher Al content aluminide coatings which have a large thermal expansion mismatch with these substrates. A lifetime model has been developed using diffusion and oxidation observations to predict coating performance as a function of temperature and initial coating composition. To test and improve the model, additional experiments are now being conducted to determine the effect of substrate composition (e.g. Cr content using Fe-12Cr and Fe-9Cr-2W substrates) and exposure temperature on the critical Al content for coating failure. Because of the unexpectedly low level of Al measured at coating failure ({approx}3.5at.% at 700 C), exposures of specimens with thick ({approx}200 {micro}m) high Al content coatings were stopped after 10kh at 800 C and 20kh at 700 C because extremely long times to failure were predicted. Post-exposure Al concentration profiles for these specimens were measured using electron microprobe.

36 MATERIALS SCIENCE↗

Performance of Al-Rich Oxidation Resistant Coatings For Fe-Base Alloys

Aluminum-rich coatings made by chemical vapor deposition and pack cementation on ferritic (e.g. Fe-9Cr-1Mo) and austenitic (Type 304L) substrates are being evaluated at 650-800 C. For oxidation testing, a humid air environment was used to quantify coating performance, as uncoated substrates experience rapid oxidation at these temperatures. A main goal of this work is to demonstrate the potential benefits and problems with alumina-forming coatings. The higher exposure temperatures were selected to accelerate the degradation of the coating by interdiffusion with the substrate. A general conclusion of this testing was that coatings with less Al and a ferritic Fe(Al) structure could be more durable than higher Al content aluminide coatings which have a large thermal expansion mismatch with these substrates. A lifetime model has been developed using diffusion and oxidation observations to predict coating performance as a function of temperature and initial coating composition. To test and improve the model, additional experiments are now being conducted to determine the effect of substrate composition (e.g. Cr content using Fe-12Cr and Fe-9Cr-2W substrates) and exposure temperature on the critical Al content for coating failure. Because of the unexpectedly low level of Al measured at coating failure ({approx}3.5at.% at 700 C), exposures of specimens with thick ({approx}200 {mu}m) high Al content coatings were stopped after 10kh at 800 C and 20kh at 700 C because extremely long times to failure were predicted. Post-exposure Al concentration profiles for these specimens were measured using electron microprobe.

36 MATERIALS SCIENCE↗