Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Overview of Additively Manufactured TPS Proposed Flight Test and Earth Re-Entry Capsule Design

A flight mechanics overview is presented of an Earth flight test designed to investigate a novel, 3D printed thermal protection system (TPS) that is currently in development at NASA as part of the Additive Manufacturing of Thermal Protection Systems project. The project is pioneering a method to print a thermal protection system onto an entry vehicle forebody one layer at a time. This method reduces labor and complexity as compared to traditional manufacturing methods while increasing mission-dependent customization of through-depth materials properties. The flight test has three objectives. First, subject the forebody stagnation point of a capsule equipped with additively manufactured TPS (AMTPS) material to peak heat fluxes in excess of 100 $W/cm^2$. Second, capture in-flight data to enable flight reconstruction and AMTPS material thermal response model improvement. Third, recover the capsule with data storage and forebody AMTPS intact to enable post-flight inspection and analysis of AMTPS performance. The flight test trajectory is designed to achieve a peak stagnation point, cold-wall, entry heat flux of 135~$W/cm^2$. Flight mechanics simulations are performed using the Program to Optimize Simulated Trajectories II (POST2) and Monte-Carlo analysis yields statistical percentiles on vehicle performance at key points along the trajectory. Based on the flight mechanics analysis presented in this paper, a prototype capsule was designed, partially fabricated, and underwent preliminary component stress testing in preparation for fabrication of the flight unit capsule. The capsule outer mold line is a modified version of the heritage Mars Microprobe geometry. The capsule has a 0.356~m diameter, a 30~kg mass, and a hypersonic ballistic coefficient of 300~$kg/m^2$. Sensor selection is guided by flight dynamics simulations with the goal of resolving the re-entry heating pulse. On-board instrumentation include forebody and aftbody pressure sensors and thermocouples, a 9-axis IMU, a GPS receiver, and an Iridium satellite modem, all of which collect and store data throughout flight via on-board avionics systems. A two-stage parachute system is designed to decelerate the capsule to touchdown velocities that will not result in significant fracture or deformation of the charred AMTPS material at ground impact.

Flight Mechanics↗
NASA NTRSDate not supplied

Thermal Modelling of the in-Situ Consolidation of Automated Fiber Placement of Thermoplastic Composites

NASA is developing carbon fiber reinforced thermoplastic composites processing methods under the Hi-rate Composites Aircraft Manufacturing (HiCAM) project. The in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process has high potential to increase manufacturing throughput and lower costs as it combines the repeatability and fast lay down rates of AFP with the thermoformability of thermoplastic materials to achieve part consolidation out of the autoclave. Physics-based process models are employed in the ICAT process development to understand, fundamentally, the thermal response of the carbon fiber (CF)/polyaryletherketone (PAEK) material during the rapid heating and cooling associated with laser-assisted AFP. A one-dimensional (1-D) closed-form model was developed capable of predicting the temperature profile through-the-thickness of the tape material. In addition, a two-dimensional (2-D) model was developed to predict the heat transfer through-the-thickness and in the laydown x-direction of the AFP head motion. The solution of the Fourier heat-transfer equations in the 2-D model is approximated using the explicit finite difference numerical method. The temperature profile during placement of PAEK slit-tape materials at various laser target temperatures and placement speeds were measured during ICAT process development trials at Electroimpact®, Inc. †† and the resulting experimental data is compared with the predictions of the 1-D and 2-D models.

Thermoplastics↗
NASA NTRSDate not supplied

LOFTID Surface Heating Reconstruction

On November 10, 2022, the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) reentry vehicle launched to low-Earth orbit aboard a United Launch Alliance Atlas V rocket out of Vandenberg Air Force Base. The aeroshell, the largest Hypersonic Inflatable Aerodynamic Decelerator (HIAD) ever flown, was inflated to its full 6-meter diameter before successful re-entry into the atmosphere. The aeroshell was heavily instrumented in order to understand its behavior during entry. There were 82 thermocouples (TCs) distributed across the aeroshell, with 22 integrated into the flexible thermal protection system (FTPS) on the rigid nose, 36 in the FTPS on the deployable structure, and 24 on the inflatable structure. TCs were placed at different depths throughout the FTPS. Those nearest to the surface were located just beneath the two SiC outer fabric layers. The near-surface TCs on the rigid nose were Type R with flame spray alumina insulation, while those on the flank were Type N with mica/ceramic insulation. Additionally, a radiometer was placed at the center of the nose surrounded by four total heat flux gauges in a cruciform configuration at a radius of 0.41 m. The nose instrumentation is shown in Fig. 1 and a cross-section of the aeroshell with all TC locations is shown in Fig. 2. The objective of this work was to use the temperatures measured by the TCs during flight to estimate the surface heat rate across the aeroshell throughout the period of re-entry by inverse analysis methodology. The results were used to evaluate the fidelity of measurements from the total heat flux gauges on the nose, determine the surface heat flux at aeroshell locations where gauges were not present, and compare to pre-flight CFD-based heating predictions. Inversely estimated surface heat flux continues to be used to correlate FTPS thermal models to reconstruct in-flight thermal response.

H S Alpert↗
NASA NTRSDate not supplied

Thermal Modelling of the In-Situ Consolidation of Automated Fiber Placement Of Thermoplastic Composites

NASA is developing carbon fiber reinforced thermoplastic composites processing methods under the Hi-rate Composites Aircraft Manufacturing (HiCAM) project. The in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process has high potential to increase manufacturing throughput and lower costs as it combines the repeatability and fast lay down rates of AFP with the thermoformability of thermoplastic materials to achieve part consolidation out of the autoclave. Physics-based process models are employed in the ICAT process development to understand, fundamentally, the thermal response of the carbon fiber (CF)/polyaryletherketone (PAEK) material during the rapid heating and cooling associated with laser-assisted AFP. A one-dimensional (1-D) closed-form model was developed capable of predicting the temperature profile through-the-thickness of the tape material. In addition, a two-dimensional (2-D) model was developed to predict the heat transfer through-the-thickness and in the laydown x-direction of the AFP head motion. The solution of the Fourier heat-transfer equations in the 2-D model is approximated using the explicit finite difference numerical method. The temperature profile during placement of PAEK slit-tape materials at various laser target temperatures and placement speeds were measured during ICAT process development trials at Electroimpact®, Inc. †† and the resulting experimental data is compared with the predictions of the 1-D and 2-D models.

Christopher J. Stelter↗
NASA NTRSDate not supplied

LOFTID Surface Heating Reconstruction

On November 10, 2022, the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) reentry vehicle launched to low-Earth orbit aboard a United Launch Alliance Atlas V rocket out of Vandenberg Air Force Base. The aeroshell, the largest Hypersonic Inflatable Aerodynamic Decelerator (HIAD) ever flown, was inflated to its full 6-meter diameter before successful re-entry into the atmosphere. The aeroshell was heavily instrumented in order to understand its behavior during entry. There were 82 thermocouples (TCs) distributed across the aeroshell, with 22 integrated into the flexible thermal protection system (FTPS) on the rigid nose, 36 in the FTPS on the deployable structure, and 24 on the inflatable structure. TCs were placed at different depths throughout the FTPS. Those nearest to the surface were located just beneath the two SiC outer fabric layers. The near-surface TCs on the rigid nose were Type R with flame spray alumina insulation, while those on the flank were Type N with mica/ceramic insulation. Additionally, a radiometer was placed at the center of the nose surrounded by four total heat flux gauges in a cruciform configuration at a radius of 0.41 m. The nose instrumentation is shown in Fig. 1 and a cross-section of the aeroshell with all TC locations is shown in Fig. 2. The objective of this work was to use the temperatures measured by the TCs during flight to estimate the surface heat rate across the aeroshell throughout the period of re-entry by inverse analysis methodology. The results were used to evaluate the fidelity of measurements from the total heat flux gauges on the nose, determine the surface heat flux at aeroshell locations where gauges were not present, and compare to pre-flight CFD-based heating predictions. Inversely estimated surface heat flux continues to be used to correlate FTPS thermal models to reconstruct in-flight thermal response.

LOFTID↗
NASA NTRSDate not supplied

Three Dimensionally Woven Mid-Density Carbon Phenolic (3MDCP) is a Novel Single Piece Ablative TPS for Extreme Entry Environments

Three Dimensionally Woven Mid-Density Carbon Phenolic (3MDCP) is robust, single piece, carbon phenolic ablative thermal protection system under development at NASA Ames Research Center initially for the Mars Sample Return Earth Entry System (MSR EES). The MSR EES requirements drove the need for TPS with no seams, capable of surviving the highest entry conditions for any NASA Earth return capsule with heat fluxes >2000 W/cm2 and pressures >1.5 atmospheres. To produce 3MDCP required development of new weaving infrastructure to enable weaving of preforms large enough to form into a single piece heatshield. It required development of forming techniques to transform a flat woven panel into a sphere cone shape and enhanced infusion processes to support larger scale infusion of resin into the formed preforms. A rigorous performance testing campaign was conducted to develop and validate the materials thermal response model used to determine the required material thickness and to demonstrate the material can survive the extreme entry conditions. The end of the development effort (end of FY26) will result in a TPS at Technical Readiness Level (TRL) 6 and Manufacturing Readiness Level (MRL) 6+ for the MSR EES mission and a mature system ready to support other missions. This poster will provide a snapshot of where 3MDCP is in its development phase.

Ablator↗
NASA NTRSDate not supplied

Artemis II Mission Performance of the Orion Active Thermal Control System

The Orion spacecraft has recently completed Artemis II, the first crewed mission around the moon in 54 years. This test flight demonstrated vehicle capability as the foundation for all future missions under the Artemis program. As a major system of Orion, the Active Thermal Control System (ATCS) successfully managed crew and vehicle heat loads to provide adequate cooling and thermal comfort for the duration of the Artemis II mission. Thermal control on the Orion vehicle is managed through two redundant cooling loops in the Crew Module (CM) that absorb heat loads from the cabin and Air Revitalization System (ARS) heat exchangers, the Liquid Cooling Garment (LCG) heat exchanger, and the avionics cold plates, and then transfer those heat loads to the Service Module (SM) radiator loops and/or the Phase Change Material (PCM) and ammonia boilers when required through thermal configuration or mission phase. During Artemis II, Orion did not necessitate any supplemental cooling from ammonia boilers until service module separation, allowing the maximum availability of ammonia cooling prior to entry. This presentation will provide an overview of the Orion ATCS major subsystems, highlight the performance during key mission phases, and comment on the applicability of the observed thermal response to future Artemis missions.

Ellie Thurston↗
NASA NTRS1998

Thermal Characteristics of Urban Landscapes

Although satellite data are very useful for analysis of the urban heat island effect at a coarse scale, they do not lend themselves to developing a better understanding of which surfaces across the city contribute or drive the development of the urban heat island effect. Analysis of thermal energy responses for specific or discrete surfaces typical of the urban landscape (e.g., asphalt, building rooftops, vegetation) requires measurements at a very fine spatial scale (i.e., less than 15 m) to adequately resolve these surfaces and their attendant thermal energy regimes. Additionally, very fine scale spatial resolution thermal infrared data, such as that obtained from aircraft, are very useful for demonstrating to planning officials, policy makers, and the general populace the benefits of the urban forest. These benefits include mitigating the urban heat island effect, making cities more aesthetically pleasing and more habitable environments, and aid in overall cooling of the community. High spatial resolution thermal data are required to quantify how artificial surfaces within the city contribute to an increase in urban heating and the benefit of cool surfaces (e.g., surface coatings that reflect much of the incoming solar radiation as opposed to absorbing it thereby lowering urban temperatures). The TRN (thermal response number) is a technique using aircraft remotely sensed surface temperatures to quantify the thermal response of urban surfaces. The TRN was used to quantify the thermal response of various urban surface types ranging from completely vegetated surfaces to asphalt and concrete parking lots for Huntsville, AL.

Luvall, Jeffrey C.↗
NASA NTRS2021

Matrix Microcracking Effect on the Structural Response of a Thermal Protection System

The effect of microcracking in the phenolic matrix of a three-dimensional woven thermal protection system (TPS) and resulting material stiffness reduction was studied via a comparison of finite element results from linear and iterative linear analyses. A dual-layer continuous dry weave material with a low-density phenolic resin matrix has been developed for use in extreme environments. Due to high stresses in the through-the-thickness direction, microcracks may form in the matrix. The matrix does not have structural load transfer requirements, and testing has shown that microcracked phenolic resin satisfies thermal requirements. Microcracks in the matrix would result in a reduction of stiffness, which could alter the structural performance. A study was conducted to determine if reduction in material stiffness would change the load paths or structural margins. A linear finite element analysis that did not account for microcracking and an iterative linear finite element analysis that accounted for propagation microcracks were compared. Four subcases were analyzed with results indicating that the assumed propagation strength for the microcracking is the critical parameter for determining the extent of microcracking. Phenolic microcracking does not appear to have an adverse effect on the structural response and is not a critical failure for the modeled TPS.

Thermal Protection System↗
NASA NTRS1962

Numerical Analysis of the Transient Response of Advanced Thermal Protection Systems for Atmospheric Entry

Equations for the transfer of heat through thermal protection shields are derived in finite difference form. These equations are applicable to charring ablators, impregnated ceramics, subliming ablators, heat sinks, and insulating materials and have been programed for solution on a high-speed digital computer. In the program, thermal properties can be functions of temperature. Provision is made for analysis of heat shields subjected to simultaneous convective and radiative heat inputs. Some typical results are presented. Limited comparisons with experimental results are made.

THERMAL PROTECTION↗
NASA NTRS1993

Mars: The initial emplacement of ground ice in response to the thermal evolution of its early crust

Given the geomorphic evidence for the widespread occurrence of water and ice in the early martian crust, and the difficulty involved in accounting for this distribution given the present climate, it has been suggested that the planet's early climate was originally more Earth-like, permitting the global emplacement of crustal H2O by direct precipitation as snow or rain. The resemblance of the martian valley networks to terrestrial runoff channels, and their almost exclusive occurrence in the planet's ancient (approximately 4 billion year old) heavily cratered terrain, is often cited as evidence of just such a period. An alternative school of thought suggests that the early climate did not differ substantially from that of today. Advocates of this view find no compelling reason to invoke a warmer, wetter period to explain the origin of the valley networks. Rather, they cite evidence that the primary mechanism of valley formation was ground water sapping, a process that does not require that surface water exist in equilibrium with the atmosphere. However, while sapping may successfully explain the origin of the small valleys, it fails to address how the crust was initially charged with ice as the climate evolved towards its present state. Therefore, given the uncertainty regarding the environmental conditions that prevailed on early Mars, the initial emplacement of ground ice is considered from two perspectives: (1) that the early climate started warm and wet, but gradually cooled with time; and (2) that it never differed substantially from that of today.

Clifford, Stephen M.↗
NASA NTRS1990

Studies of the thermal and optical responses of H atoms in solid H2

It was the goal of this reserch project to model both the storage of energy in solid hydrogen in the form of atoms and the conversion of this stored energy into other forms of useful energy. The basic ideas of rocket propulsion originate in classical physics and they remain unchanged. To escape a strong gravitational field, the 'burn time' must be minimized but in negligible force fields, the burn time is unimportant and only the relative masses of rocket to fuel determine a specific exhaust velocity. It is in this latter case that low mass fuels such as hydrogen become very important. The burning of hydrogen in oxygen is a 'benchmark' fuel today providing a specific impulse of 400 seconds or better. More exotic fuels will be needed for many of the interesting explorations of the future but they still must have large energy releases per unit mass. It is in this context that propulsion based on hydrogen atom recombination receives attention and these studies will serve as engineering guides.

Gaines, James R.↗
NASA NTRS2013

Post-flight Analysis of Mars Science Laboratory Entry Aerothermal Environment and Thermal Protection System Response

The Mars Science Laboratory successfully landed on the Martian surface on August 5th, 2012. The rover was protected from the extreme heating environments of atmospheric entry by an ablative heatshield. This Phenolic Impregnated Carbon Ablator heatshield was instrumented with a suite of embedded thermocouples, isotherm sensors, and pressure transducers. The sensors monitored the in-depth ablator response, as well as the surface pressure at discrete locations throughout the hypersonic deceleration. This paper presents a comparison of the flight data with post-entry estimates. An assessment of the aerothermal environments, as well as the in-depth response of the heatshield material is made, and conclusions regarding the overall performance of the ablator at the suite locations are presented.

mars science laboratory↗
NASA NTRSDate not supplied

Response of Ablative Thermal Protection Materials to Degradation in Low Earth Orbit –Characterization of Specimens from MISSE-13

The environment of low Earth orbit presents unique material interactions due to the presence of atomic oxygen and solar spectrum UV. A variety of degradation mechanisms can occur depending, inlarge part, on the specific material system involved. This talk will review the characterization of two ablative materials, PICA-D and HEEET, as well as relevant adhesive joints and coatings. PICA-D is a variant of the phenolic impregnated carbon ablator (PICA) and is the baseline thermal protection system (TPS) on Dragonfly and the lander for Mars Sample Return (MSR). HEEET is a 3D woven system from which MSR’s Earth entry TPS is derived. The samples for these materials were flown in orbit during the Materials International Space Station Experiment-13 (MISSE-13) which launched on March 6, 2020 and returned to Earth on January 13, 2021. Changes to surface microstructure and reflectivity will be presented along with tomographic analysis. The effect of differential erosion rates on the composites and the impacts of the orbit environment on coating performances will be discussed in the context of TPS performance and mission design aspects.

MISSE↗
NASA NTRSDate not supplied

Response of Ablative Thermal Protection Materials to Degradation in Low Earth Orbit – Characterization of Specimens from MISSE-13

The environment of low Earth orbit presents unique material interactions due to the presence of atomic oxygen and solar spectrum UV. A variety of degradation mechanisms can occur depending, in large part, on the specific material system involved. This talk will review the characterization of two ablative materials, PICA-D and HEEET, as well as relevant adhesive joints and coatings. PICA-D is a variant of the phenolic impregnated carbon ablator (PICA) and is the baseline thermal protection system (TPS) on Dragonfly and the lander for Mars Sample Return (MSR). HEEET is a 3D woven system from which MSR’s Earth entry TPS is derived. The samples for these materials were flown in orbit during the Materials International Space Station Experiment-13 (MISSE-13) which launched on March 6, 2020 and returned to Earth on January 13, 2021. Changes to surface microstructure and reflectivity will be presented along with tomographic analysis. The effect of differential erosion rates on the composites and the impacts of the orbit environment on coating performances will be discussed in the context of TPS performance and mission design aspects.

MISSE↗