Search NASA⌕ Search

SEARCH · Search NASA

Results for “BOLT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Limited Characterization of Wind Turbine Adhesives [EPIKOTE Resin MGS BPR 135G3/EPIKURE Curing Agent MGS RIMH 134 (H134i) and MGS BP20/EPIKURE Curing Agent MGS BPH 20 (rework adhesive)] and Root Insert Exterior Surface.

The National Rotor Testbed (NRT) is a wind turbine blade research program in the Sandia National Laboratories (SNL) Wind Department that has developed a new blade design. Each blade includes bonded-in, threaded metal root inserts that enable the blades to be bolted onto the wind turbine hub. Prior to installing the flight blades on the turbine, root insert strength verification tests exhibited a subset of failures below the design load on one (NRT-02) of four blades. As part of a root cause analysis for the failures, this work analyzes "scraps" of the epoxy adhesive used to bond the metal inserts into the blade and uses surface topography and x-ray fluorescence (XRF) measurements to characterize the exterior surface of the root insert. Samples were taken from inserts that exhibited both high and low loads at failure, as well as some "control inserts" to monitor the state of the surface throughout the manufacturing process. Differences in the calorimetric response of the adhesive from the separate root inserts are apparent but none of them appear to relate to the pull load required to dislodge the inserts. Two takeaways of note include: In the way that the adhesive is processed, it does not reach full cure; and, Something occurred to sample#10 such that the fully-cured adhesive has a significantly lower T g .

17 WIND ENERGY↗
DOE OSTI2021

Replaceable Paddle Tip Fabrication and Testing for Saltstone Production Facility (SPF) Mixer (FY2020 Update)

Details of the operations and issues related to the paddles used in the Saltstone Production Facility (SPF) employing the 10-inch READCO ™ -Kurimoto co-rotating dual shaft continuous mixer are provided in SRNL-ST1-2019-00142, Based on a recent effort performed by the Savannah River National Laboratory (SRNL) and funded by Savannah River Remediation (SRR), eight different replaceable paddle designs were proposed and the angled notched design was selected for this study. This design was selected over the other designs due to its simplicity and its ability to meet the fitness of duty requirements. There are two types of angled notched replaceable tip designs, one being flat and the other helical. Either of these designs can be used for blending the premix with the salt solution. Stress calculations performed on this design (the use of the bolts and connections) are documented in M-CLC-Z-00137 showing it was suitable for use.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

A simple levelset contact algorithm for large overlap removal and robust preloads

A simple approach to simulate contact between deformable objects is presented which relies on levelset descriptions of the Lagrangian geometry and an optimization-based solver. Modeling contact between objects remains a significant challenge for computational mechanics simulations. Common approaches are either plagued by lack of robustness or are exceedingly complex and require a significant number of heuristics. In contrast, the levelset contact approach presented herein is essentially heuristic free. Furthermore, the presented algorithm enables resolving and enforcing contact between objects with a significant amount of initial overlap. Examples demonstrating the feasibility of this approach are shown, including the standard Hertz contact problem, the robust removal of overlap between two overlapping blocks, and overlap-removal and pre-load for a bolted configuration.

42 ENGINEERING↗
DOE OSTI2022

PORFLOW Implementation of Vadose Zone Conceptual Model for Naval Reactor Component Disposal Area in the E-Area Low Level Waste Facility Performance Assessment

PORFLOW models have been developed to implement the proposed conceptual models for the two Naval Reactor Component Disposal Areas (NRCDAs), 643-7E and 643-26E, for the purpose of evaluating dose impacts and producing disposal limits for the E-Area Low-Level Facility (LLWF). New NRCDA conceptual models were proposed by Wohlwend and Butcher (2019) for two areas within/adjacent to the E-Area LLWF used as storage/disposal sites for reactor components from the U.S. Navy since 1987. Naval Reactor (NR) waste is comprised of highly radioactive components consisting of activated corrosion-resistant metal alloy contained within welded thick-walled steel casks, and auxiliary equipment primarily contaminated with lower levels of Activated Corrosion Products (ACPs) residing on the metal surfaces and contained within thinner-walled bolted containers.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

8 Ft Vessel Refinishing Contract Introduction [Slides]

LANL utilizes spherical vessels for numerous basic science, materials, and system performance experiments. The 8 ft vessel was fabricated in the early 2000s to ASME B&PVC Section VIII Division 1 using HSLA-100 material. This vessel was not used operationally due to programmatic change in direction. Years of improper maintenance and storage has resulted in deterioration of sealing surfaces and bolt hole threads. New mission needs call for expanded capabilities in terms of vessel sizes, therefore refinishing the 8ft vessel is crucial.

42 ENGINEERING↗
DOE OSTI2021

Surplus Plutonium Disposition Sphincter Seal Development & Testing

The Surplus Plutonium Disposition Project (SPD, Project Y744) requested the Savannah River National Laboratory (SRNL) to perform a series of leak and durability tests on sphincter seals that were designed to process blend cans and shield cans into an SPD glovebox. Each sphincter seal assembly consisted of a stainless-steel outer sleeve weldment that was bolted onto the test enclosure and an aluminum inner sleeve that housed seven to nine Neoprene seals. All tests were executed to determine long term effects from processing approximately a year’s worth of blend and shield cans through the sphincter seals.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Assessment of Additive Manufacturing of Particle Accelerator [Slides]

Metal additive manufacturing of copper components has been commercialized on multiple printing modalities; including Bound Metal Deposition (BMD), Laser Powder Bed Fusion (LPBF), and Electron Beam Melting (EBM). BMD was selected at the primary printing modality for this TED because of the availability of the Markforged Metal X machine within the LANL E-2 AM research lab. Linear accelerator (LINAC) structures are similarly demonstrated technology. Accelerator structures are typically made of high purity oxygen-free electronic copper owing to the material’s high electrical and thermal conductivity. Conventionally machined and brazed, welded, or bolted designs are difficult to manufacture and require long lead times.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Contactless Position Measurement System for Remote Alignment of Highly Reflective Objects

The Contactless Position Measurement System (CPMS) permits automatic alignment of highly-reflecting components that cannot or should not be touched by human hands, such as those used in SRF cavities. CPMS also has application during maintenance of fusion reactors, when the components in the reactor are radioactive. The length of time for which humans can handle the components in order to carry out maintenance or repairs is limited. We would like to measure the relative positions of such objects so we can bring them into alignment with motorized stages, thus eliminating the need for human contact. The CPMS is a computer vision system that measures the location of highly reflective components to within a fraction of a millimeter by finding the edges of silhouette images. This is done by placing a uniform, infrared backlight behind the components, and viewing each component with two low-aberration, infrared cameras. Each of these stereoscopic cameras are located within a coordinate system we set up with reference platforms, light sources, and survey cameras distributed around the perimeter of the string assembly room, or fusion reactor. We obtain stereoscopic silhouette images of each component, and we use these to determine the position of the component within our string assembly coordinate system. The CPMS combines the silhouette images with knowledge of the dimensions of the objects to obtain the relative positions of components in its field of view. These position measurements then allow us to mechanically maneuver the components into contact. Once we know where they are, we can move the components to where they are supposed to be with motorized stages or other mechanical means, check they are in the right place, and bolt them together. In Phase I, we built a prototype infrared backlights and cameras, tested it, wrote an analysis program to fit the images. At a range of 50 cm, we are able to measure the relative positions of two stainless steel flanges with an accuracy of 150 μm rms. The next steps are to test the analysis program with motorized stages, build a full-size prototype, and implement it in an cleanroom with SRF cavity assembly. This can be done in a cost effective way given the materials with which the system is designed. As Open Source Instruments achieved more in Phase I than anticipated, despite not receiving a Phase II SBIR grant, we hope to move forward with product development and sales with a testing partner.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

ECAR-6584 MARVEL Reactor Support Frame Analysis

Idaho National Laboratory (INL) is developing a small microreactor to produce electrical power utilizing a small nuclear core and Stirling engines for power output under the Microreactor Application Research Validation and Evaluation (MARVEL) program. The MARVEL Reactor will be installed in the Transient Reactor Test (TREAT) Facility. Walsh Engineering Services, PC (WES) has contracted with the INL to support the completion of the final design. There are six main systems in the MARVEL, one of which is the MARVEL Reactor System (MRS). The MRS contains a subsystem – the Reactor Support Frame (RSF) – that supports and orients nearly all the MRS and the RSF will be bolted to the TREAT Facility. The subject of this Engineering Calculations and Analysis Report (ECAR) is the frame weldment (see Figure 1), which is the only item that is contained in the RSF subsystem and will be called herein “RSF”.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Uncertainty Quantification for Component Modeling Using the Discrete-Direct Approach

Threaded fastener behavior can be an important aspect of complex component and system behavior, but there is no one-size-fits-all finite element analysis technique. Proper modeling of threaded fastener joints requires careful consideration of many details, from test setup and data acquisition to constitutive modeling and uncertainty quantification approaches. This report details analysis of a “mini-radax” bolted-joint exemplar where a Discrete-Direct uncertainty quantification approach is employed to evaluate margin of the component. The mini-radax geometry is tested to failure on a drop table, and single-coupon tests of individual fasteners serve as foundational data for the analysis. Analysis predictions complement the test data well and provide additional context for engineering decision-making.

42 ENGINEERING↗
DOE OSTI2023

Pragmatic Uncertainty Quantification and Propagation in Inverse Estimation of Structural Dynamics Parameters given Material Property Uncertainties and Limited Sensor Data

In this report we demonstrate some relatively simple and inexpensive methods to effectively account for various sources of epistemic lack-of-knowledge type uncertainty in inverse problems. The demonstration problem involves inverse estimation of six parameters of a bolted joint that attaches a kettlebell shaped object to a thick plate. The parameters are efficiently inverted in a modal-based model calibration using gradient-based optimization. Two material properties of the kettlebell are treated as uncertain to within given epistemic uncertainty bounds. We apply and test interval and sparse-sample probabilistic approaches to account for uncertainty in the estimated parameters (and various scalar functionals of the parameters as generic quantities of interest, QOIs) due to uncertainties in the material properties. We also investigate the error effects of limited numbers of vibration sensors (accelerometers) on the kettlebell and plate, and therefore abbreviated excitation/response information in the parameter inversions. We propose and demonstrate a Leave-K-Sensors-Out “cross-prediction” UQ approach to estimate related uncertainties on the parameters and QOI functionals. We indicate how uncertainties from material properties and limited sensors are treated in a combined manner. The economical combined UQ approach involves just three to five samples (i.e. three to five inverse simulations), with no added complication or error/uncertainty from use of surrogate models for affordability. Finally, we describe a related economical UQ approach for handling potential parameter solution non-uniqueness and numerical optimization related precision uncertainties in the estimated parameter values. Indicated further research is identified.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Extending Ultrasonic Welding Techniques to New Material Pairs (FY 2023 Annual Progress Report)

Modern multimaterial vehicles require joining of various lightweight materials, such as aluminum (Al) and magnesium (Mg) alloys and carbon fiber reinforced polymers (CFRP), with advanced high-strength steels together to form a high-performance and lightweight body structure. A variety of joining methodologies (e.g., resistance spot welding, adhesive bonding, linear fusion welding, hemming, clinching, bolting, riveting) have been attempted by the automotive industry to join different materials. Often, these joining techniques are limited to only certain material combinations. For capital and operational cost, automobile original equipment manufacturers need to limit the number of joining technologies implemented on an assembly line.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solar Photovoltaic (PV) Damage Assessment After Typhoon Mawar: Findings and Recommendations for Resilient PV on Guam

A team from the National Renewable Energy Laboratory (NREL) visited Guam in August 2023 to assess failure modes of solar photovoltaic (PV) systems after Typhoon Mawar and to provide recommendations to increase the resilience of PV systems on Guam. The team visited 30 systems: commercial and utility scale, and rooftop and ground-mounted. The team observed systems with no apparent damage, as well as systems that were completely lost. Systems fared very well overall. The average failure rate of rooftop systems was 18%, with a median failure rate of 2%, meaning the few systems that suffered total loss pulled up the average. Only eight 8 of the 25 rooftop systems suffered more than 5% damage. All ground-mounted systems suffered less than 0.5% damage, aside from a carport that lost 16% of its modules. PV systems at Andersen Air Force Base suffered 5% damage on average, with a median system failure of 0.6%. In almost all cases, failures were the result of: (1) Inadequate clamping of the module frame to the mount, (2) Module mounting clamps rotating out of underlying support rail (i.e., T-bolt that rotates free at less than 60 degrees of rotation), (3) An object hitting the panel resulting in a fracture, and in some cases leading to a cascading failure of several more panels, and (4) Excessive tilt angle (in Guam, greater than 5 degrees can be a risk due to wind speed, and power production trade-offs are insignificant).

14 SOLAR ENERGY↗
DOE OSTI2024

An Advanced Pretreatment/Anaerobic Digestion (APAD) Technology for Increased Conversion of Sewage Sludge to Bio-natural Gas in Small-scale Wastewater Plants of less than Five tons Sewage Sludge a Day

The problem today of energy production from sewage sludge at small-scale is that conventional Anaerobic Digestion (AD) as used today at Wastewater Treatment Facilities (WWTF) produces too little energy for warrant use of the biogas. It further leaves 50% or more of the waste behind after the treatment. To overcome this problem, we proposed a novel concept based on Advanced Wet Oxidation & Steam Explosion (AWOEx) of the recalcitrant parts of sewage sludge left behind after AD. We further suggest upgrading biogas to renewable natural gas (RNG) using gaseous fermentation of biogas with hydrogen added by a new methanogen. Overall, the DOE funded Advanced Pretreatment & Anaerobic digestion (APAD) project showed significant improvements over current practice. The project demonstrated that AWOEx followed by AD significantly enhanced the carbon conversion efficiency from 37% to 62%, an increase of 68%. This is far higher than the metric for the specific FOA of an increase of 50%. Besides, the project showed high efficiency of our biological conversion of biogas into RNG when using a new isolate of Methanothermobacter wolfeii resulting in a 100% increased production of a refined biogas with maximum 5% CO2. With both AWOEx pretreatment and biogas upgrading, the project showed a CCE of ca. 83%, far higher than any previous work on sewage sludge. Besides over 200% higher amount of energy in the form of RNG, the APAD concept will reduce disposal cost due to significant reduction in the concentration of final sludge product after APAD. The APAD technology can operate as a bolt-on to a conventional AD plant for improving conversion of the residual organics after AD as done in this DOE project. It can further be implemented as a stand-alone process with AWOEx followed by AD for WWTF’s currently operating without AD.

09 BIOMASS FUELS↗
DOE OSTI2025

Characterization and Damping Control of Mechanical Connections to Improve Performance of Horn Stripline

Magnetic focusing horns are critical components for creating a stable beam of neutrinos for neutrino facilities, such as the Long Baseline Neutrino Facility (LBNF) and the Neutrinos and Main Injector (NuMI) beam lines at Fermilab. The pulsed magnetic horns are powered by high current electricity through long striplines, which must survive in a harsh radiation environment for the operational life of the component. Each stripline assembly consists of four layers of Al 6101-T6. As an electro-mechanical system, the stripline layers are bolted together with ceramic isolators for electrical insulation and to facilitate passive cooling and mechanical stability. The striplines experience vibrational force in addition to clamping force, repetitive thermal and electro-magnetic loading. The holes of stripline plates for ceramic joints represent one of the weak links for potential failure. Damping can be achieved by adding damp material to the joint. By characterizing behavior of the joint and optimizing their damping properties through FEA and EMA, the stripline performance and longevity can be improved. Appropriate damp materials are the key.

Liu, Zunping [Fermilab]↗
DOE OSTI2026

High Yield nTOF Spec A and NP Filter Holders Static and Seismic Analysis

The Neutron Time-of-Flight (nTOF) detectors located in the Alcove and at the North Pole (Spec A and Spec NP respectively) need filtering in the beam path to enable them to take data at NIF yields above 5MJ. The filtering consists of 12cm of filter material divided into four, 3cm thick “pucks.” The pucks are 7cm in diameter. Each puck is mounted into a rotatable stage, also called a Filter Flipper, that can bring it into and out of the beam path, see Figure 1-1. These stages are bolted onto a plate that connects the filter stages to the mounting hardware used to position them in the NIF Target Bay. The top-level filter mount assemblies will be permanently mounted in the facility; removal is possible if needed for NIF maintenance, but the design intent is for the assemblies to remain in their locations after alignment is completed.

42 ENGINEERING↗
DOE OSTI2026

Redesign of Nuclear Material Storage Container with Additive Manufacturing

The goal of this project is to reduce worker dose and improve criticality safety by improving nuclear material storage containers. The current method of medium to long term (up to 15 years) storage of small amounts of nuclear material is to store it in a stainless-steel flat tube with a copper crush gasket. These containers use 10 bolts to fasten the lid, and the crush gasket must be replaced after every use. Stainless-steel acts as a gamma shield, but there is not any material to account for neutron dose. A redesign of this container should prioritize reducing radiation doses to handlers of the container by reducing the amount of time handlers are exposed to the container and introducing material with effective neutron and gamma shielding mechanics.

42 ENGINEERING↗
DOE OSTI2019

Response of Jointed-Structures in a Shock Tube: Simultaneous PSP and DIC with Comparison to Modeling

Experiments, modeling and simulation were used to study the nonlinear dynamics of a jointed-structure in a shock tube. The structure was a full-span square cylinder with internal bolted connections excited by fluid loading. The width-based Reynolds number was ≈10 5 . The cylinder was exposed to an impulsive force associated with the incident shock followed by transverse loading imposed by vortex shedding. In the experiment, aerodynamic loading was characterized with high-speed pressure sensitive paint (PSP). Digital image correlation (DIC) concurrently measured the structural response. The maximum displacement occurred when the vortex shedding frequency most closely matched the structural mode of the beam associated with a rocking motion at the joint. A finite element model was developed using Abaqus, where the nonlinear contact dynamics of the joint were simulated using Coulomb friction. The PSP data loaded the model and the interaction was treated as one-way coupled. The simulations well-matched the trends observed in the experiment. Overall, the root-mean-square values of the transverse displacement agreed to within 24% of the experiment. The modeling showed rocking about the joint during vortex shedding was critical to the nonlinear damping and energy dissipation in the structure. We conclude this campaign highlights the importance of jointed-connections to energy dissipation in structures under aerodynamic loading.

42 ENGINEERING↗