SEARCH · Search NASA

Results for “CAST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Radiochronometric discordance in cast uranium metal: a multi-laboratory intercomparison exercise

Here, the model age of a nuclear material is crucial in nuclear forensic analysis. Uranium metals with complex production histories often exhibit discordant model ages from the 230 Th– 234 U and 231 Pa– 235 U chronometers. Recent studies involving targeted uranium metal castings have enhanced our understanding of decay product behavior during casting, aiding nuclear forensic interpretation. Building on this prior work, forensics laboratories at Atomic Weapons Establishment (AWE), Lawrence Livermore National Laboratory (LLNL), and Los Alamos National Laboratory (LANL) conducted an interlaboratory comparison to investigate spatial heterogeneity in uranium metal cast under controlled conditions. Each laboratory measured samples of a mixed feedstock and its corresponding cast product. This work furthers our understanding of discordant model ages and the use of discordance as a signature to enhance confidence in interpretations of radiochronometric data for nuclear forensics.

230Th/234U↗

DOE OSTI2024

Effect of Si impurities on microstructure and tensile properties of a cast Al-Mg-Fe alloy

Al-Mg alloys are attractive for structural castings owing to their superior strength and ductility in the as-cast state. However, given the tight tolerance for impurities, Al-Mg alloys produced from secondary sources still face multiple challenges. Here, we report the effect of increased Si impurity (0.05–1.6 wt%), which is commonly found in secondary Al sources, on microstructure and tensile properties of a cast Al-4.3Mg-1.6Fe (wt%) alloy, commercially referred to as Castaduct-42 alloy. Microstructural characterization revealed that Si addition increased the volume fraction, size, and aspect ratio of primary Al13Fe4 intermetallic particles as well as the volume fraction of other binary and ternary eutectic phases. Tensile testing results demonstrated that increasing Si impurities from 0.05 to 1.6 wt% reduced ductility from 14.3 ± 1.4 % to 2.2 ± 1.0 %. A particle cracking damage accumulation model coupled with failure analysis indicated primary Al13Fe4 intermetallic particles to be the major contributing factor to the deterioration in ductility with increasing Si content. Additionally, the stabilizing effect of Si on primary Al 13 Fe 4 was inconsistent with the CALPHAD calculation results based on existing CALPHAD databases which predict a slightly decreasing primary Al13Fe4 phase fraction with increasing Si concentration. This work provides new insights into the phase stability and mechanical behavior of the lesser studied Al-Mg-Fe-Si alloy system that will contribute to the development of sustainable cast Al-Mg based alloys.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Additively manufactured and cast high-temperature aluminum alloys for electric vehicle brake rotor application

Electric vehicle brake rotors demand lightweight, high thermal conductivity materials with good resistance to wear, creep, salt corrosion, and thermal fade, all of which present challenges to the traditionally used cast iron. In this work, we investigated the braking performance of recently developed high-temperature aluminum alloys in both cast and 3D printed forms, that possess excellent microstructural and mechanical stability at elevated temperatures. Three aluminum alloys, Al-6Cu-Mn-Zr, Al-9Cu-Mn-Zr, and Al-Ce-Ni-Mn-Zr and a reference cast iron were tested on a sub-scale brake tester against a commercial brake pad material over a range of sliding speeds between 2 and 15 m/s. The performance of these alloys was evaluated for wear resistance, friction behavior, temperature elevation, and surface morphological change. Although all three candidate alloys had lower wear-resistance than cast iron, Al-Ce-Ni-Mn-Zr showed a significantly reduced wear rate in comparison to the Al-Cu-Mn-Zr alloys. Moreover, Al-Ce-Ni-Mn-Zr alloy had the most consistent friction behavior at all sliding speeds and good fade resistance, as the coefficient of friction did not dramatically decrease with temperature rise but stayed within a desirable range of 0.35–0.50 instead. The superior wear resistance and braking performance of the Al-Ce-Ni-Mn-Zr alloy were attributed to its higher hardness, and high temperature yield strength and creep resistance compared with the Al-Cu-Mn-Zr alloys. In conclusion, the results suggest that the braking performance of these aluminum alloys could be further enhanced by increasing the hardness and forming a more stable transfer layer on the sliding surface.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Center for Alternate Synchronization and Timing (CAST) PTP Network Monitoring Report

The Oak Ridge National Laboratory Center for Alternative Synchronization and Timing (CAST) performs research, development, testing, and evaluation of alternative terrestrial-based timing and synchronization infrastructure for the US power grid and other critical infrastructures. Alternative timing options reduce reliance on GPS and enhance the overall resilience of critical infrastructures. CAST infrastructure uses Precision Time Protocol (PTP) as the primary conduit for delivery of synchronization packets. CAST deploys PTP over long terrestrial links to synchronize a multitude of remote boundary clocks and downstream power grid components with the authoritative grand master clocks. Network traffic issues can severely degrade PTP accuracy. This report focuses on examining network traffic anomalies and their effects on PTP operation as well as the potential implications to CAST’s high-precision remote synchronization operations.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2026

Additive Manufacturing Evaporative Casting

Traditional lost foam casting has been around for decades. The process uses foam forms blown by an injection molding like process or CNC milled into the desired shape, then pouring molten metal over the foam pattern to create a metallic object. Additive Manufacturing Evaporative Casting (AMEC) is a new process that eliminates foam forms by using additive manufacturing to 3D print the desired cast geometry. This not only saves time and money but allows for more advanced and complex designs that can’t be achieved by carving foam. Additionally, AMEC doesn’t require molds and tooling like other casting and foundry options. Because the AMEC process is new, extensive testing is needed to develop a better understanding of the process to minimize defects, quantify material properties, and start computer modeling for the process. This CRADA (collaborative research and development agreement) between ORNL and Skuld seeks to improve the process, develop a computational model, characterize material properties, and explore new applications.

36 MATERIALS SCIENCE↗

NASA NTRS1980

A silicon sheet casting experiment

The casting of silicon blanks for solar cells directly without slicing is an exciting concept. An experiment was performed to investigate the feasibility of developing a machine that casts wafers directly. A Czochralski furnace was modified to accept a graphite ingot-simulating fixture. Silicon was melted in the middle of the ingot simulator in a boron nitride mold. Sample castings showed reasonable crystal size. Solar cells were made from the cast blanks. The performance is reported.

Bickler, D. B.↗

NASA NTRS1982

Alterations in mitochondria and sarcoplasmic reticulum from heart and skeletal muscle of horizontally casted primates

Horizontally body-casted rhesus monkeys are used as an animal model in order to study the physiological changes known as cardiovascular deconditioning which occur during weightless conditions. No difference was found between the experimental and control animals in heart mitochondrial oxidative phosphorylation which indicates that no apparent changes occurred in the primary energy-producing system of the heart. A marked increase in cytochrome oxidase activity was observed in the casted primate heart mitochondria compared to controls, while a 25% decrease in respiratory substrate-supported calcium uptake was found in casted primate heart mitochondria compared to controls. Sacroplasmic reticulum isolated from the primate hearts revealed marked changes in calcium transport activities. It is concluded that the marked depression in cardiac sarcoplasmic reticulum functions indicates altered calcium homeostasis in the casted-primate heart which could be a factor in cardiovascular deconditioning.

Sordahl, L. A.↗

NASA NTRS1984

Effect of mild atherosclerosis on flow resistance in a coronary artery casting of man

An in-vitro flow study was conducted in a mildly atherosclerotic main coronary artery casting of man using sugar-water solutions simulating blood viscosity. Steady flow results indicated substantial increases in pressure drop, and thus flow resistance at the same Reynolds number, above those for Poiseuille flow by 30 to 100 percent in the physiological Reynolds number range from about 100 to 400. Time-averaged pulsatile flow data showed additional 5 percent increases in flow resistance above the steady flow results. Both pulsatile and steady flow data from the casting were found to be nearly equal to those from a straight, axisymmetric model of the casting up to a Reynolds number of about 200, above which the flow resistance of the casting became gradually larger than the corresponding values from the axisymmetric model.

Back, L. H.↗

NASA NTRS1983

Steps toward 8 m honeycomb mirror blanks. II - Experiments with waffleplate and honeycomb casting

A technique for fabricating large low-cost light-weight borosilicate-glass mirrors for ground and space-based astronomy is described. This technique involves the remelting of glass into complex molds for vacuum-formed ceramic fiber and is used to cast in one piece either waffleplate or full honeycomb sandwich blanks. The construction of molds and the cycle for melting and annealing are described in detail. A 1.1-m square blank with a 22.4-cm-thick face and 1.6-cm ribs, 15-cm deep on 15-cm squares, has been cast, and a 1.8-m circular blank of full honeycomb construction is scheduled for production. The casting of blanks of up to 8-m in diameter is anticipated, with densities of 200 kg/sq m (like that of the ST mirror) being typical of casting.

Hill, J. M.↗

NASA NTRS1985

Graphite Formation in Cast Iron

In the first phase of the project it was proven that by changing the ratio between the thermal gradient and the growth rate for commercial cast iron samples solidifying in a Bridgman type furnace, it is possible to produce all types of graphite structures, from flake to spheroidal, and all types of matrices, from ferritic to white at a certain given level of cerium. KC-135 flight experiments have shown that in a low-gravity environment, no flotation occurs even in spheroidal graphite cast irons with carbon equivalent as high as 5%, while extensive graphite flotation occurred in both flake and spheroidal graphite cast irons, in high carbon samples solidified in a high gravity environment. This opens the way for production of iron-carbon composite materials, with high carbon content (e.g., 10%) in a low gravity environment. By using KC-135 flights, the influence of some basic elements on the solidification of cast iron will be studied. The mechanism of flake to spheroidal graphite transition will be studied, by using quenching experiments at both low and one gravity for different G/R ratios.

Stefanescu, D. M.↗

NASA NTRS1987

High-Density-Tape Casting System

Centrifuge packs solids from slurry into uniform, dense layer. New system produces tapes of nearly theoretical packing density. Centrifugal system used to cast thin tapes for capacitors, fuel cells, and filters. Cylindrical rotary casting chamber mounted on high-speed bearings and connected to motor. Liquid for vapor-pressure control and casting slurry introduced from syringes through rotary seal. During drying step, liquid and vapor vented through feed tubes or other openings. Laminated tapes produced by adding more syringes to cast additional layers of different materials.

Collins, Earl R., Jr.↗

NASA NTRS1988

The influence of high thermal gradient casting, hot isostatic pressing and alternate heat treatment on the structure and properties of a single crystal nickel base superalloy

A development program has been conducted to improve the cyclic properties of the PWA 1480 single-crystal superalloy by reducing or entirely eliminating casting porosity at fatigue-initiation sites, through the use of improved casting process parameters and HIPing; potential mechanical property improvements in a high-pressure hydrogen environment were also sought in alternatives to the standard coating and heat-treatment cycle. High thermal gradient casting was found to yield a reduction in overall casting porosity density and pore sizes. The most dramatic mechanical property improvement resulted from HIPing.

Fritzemeier, L. G.↗

NASA NTRS1991

Casting Of Multilayer Ceramic Tapes

Procedure for casting thin, multilayer ceramic membranes, commonly called tapes, involves centrifugal casting at accelerations of 1,800 to 2,000 times normal gravitational acceleration. Layers of tape cast one at a time on top of any previous layer or layers. Each layer cast from slurry of ground ceramic suspended in mixture of solvents, binders, and other components. Used in capacitors, fuel cells, and electrolytic separation of oxygen from air.

Collins, Earl R., Jr.↗

NASA NTRS1986

Composite ingot casting

A method and system for continuously or semicontinuously casting a composite metal article, such as a structurally composite ingot or the like, wherein one of the principal structural components of the ingot comprises an aluminum-lithium alloy. During such casting by a D.C. (direct chill) conventional tubular mold or electromagnetic process, the aluminum-lithium structural component of a structurally composite ingot is encircled or peripherally encased by a· further outer metal cladding component that can be cast simultaneously with the aluminum-lithium component such as another outer aluminous alloy from which lithium is absent as a constituent or impurity, although it may be present and tolerated as a trace element. In this arrangement the aluminum-lithium structural component is prevented during casting from coming into direct contact with the chilling coolant, normally water, with which lithium can react violently. Only the outer aluminous alloy envelope is subjected to the direct contact of a liquid coolant whereby as it solidifies, this outer envelope or . peripheral sheath acts as an impervious secondary mold for and protects the inner aluminum--lithium alloy structural component which is then directly controllably chilled and solidified.

George J Binczewski↗

NASA NTRS1993

Interfacial Shear Strength of Cast and Directionally Solidified Nial-Sapphire Fiber Composites

The feasibility of fabricating intermetallic NiAl-sapphire fiber composites by casting and zone directional solidification has been examined. The fiber-matrix interfacial shear strengths measured using a fiber push-out technique in both cast and directionally solidified composites are greater than the strengths reported for composites fabricated by powder cloth process using organic binders. Microscopic examination of fibers extracted from cast, directionally solidified (DS), and thermally cycled composites, and the high values of interfacial shear strengths suggest that the fiber-matrix interface does not degrade due to casting and directional solidification. Sapphire fibers do not pin grain boundaries during directional solidification, suggesting that this technique can be used to fabricate sapphire fiber reinforced NiAl composites with single crystal matrices.

Tewari, S. N.↗

NASA NTRS1995

Improved Net-Level Filling And Finishing Of Large Castings

Improved method of vacuum casting of large, generally cylindrical objects to net sizes and shapes reduces amount of direct manual labor by workers in proximity to cast material. Original application for which method devised is fabrication of solid rocket-motor segments containing solid propellant, wherein need to minimize exposure of workers to propellant material being cast. Improved method adaptable to other applications involving large castings of toxic, flammable, or otherwise hazardous materials.

Johnson, Erik P.↗

NASA NTRS1996

Adhesion Casting In Low Gravity

Adhesion casting in low gravity proposed as technique for making new and improved materials. Advantages of low-gravity adhesion casting, in comparison with adhesion casting in normal Earth gravity, comes from better control over, and greater uniformity of, thicknesses of liquid films that form on and adhere to solid surfaces during casting.

Noever, David A.↗

NASA NTRS2000

Application of Rapid Prototyping to the Investment Casting of Test Hardware (MSFC Center Director's Discretionary Fund Final Report, Project No. 98-08)

Investment casting masters of a selected propulsion hardware component, a fuel pump housing, were rapid prototyped on the several processes in-house, along with the new Z-Corp process acquired through this project. Also, tensile samples were prototyped and cast using the same significant parameters. The models were then shelled in-house using a commercial grade zircon-based slurry and stucco technique. Next, the shelled models were fired and cast by our in-house foundry contractor (IITRI), with NASA-23, a commonly used test hardware metal. The cast models are compared by their surface finish and overall appearance (i.e., the occurrence of pitting, warping, etc.), as well as dimensional accuracy.

Cooper, K. G.↗