Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fusion Energy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

An optimization approach for cryogenic distillation-based protium removal systems in magnetic fusion energy fuel cycles

Tritium inventory reduction for fusion power plants is central to the successful adoption of fusion energy. The advent of direct internal recycling in deuterium-tritium fusion fuel cycle design has led to significant reduction in startup tritium inventory estimates for fusion power plants but requires an isotope rebalancing and protium removal (IRPR) system to ensure acceptable isotopic fuel composition. Cryogenic distillation is a potential solution for near-term deployment in an IRPR system due to its demonstrated performance in similar operating regimes. Using protium removal in the fuel cycle as the primary performance metric, this paper presents an optimization methodology for a single-column continuous cryogenic distillation-based IRPR system for a 500 MW fus magnetic fusion device. Distillation column optimization was performed using the CryOgenic Distillation For Isotopic Separation of Hydrogen (CODFISH) code developed at Savannah River National Laboratory. The distillation column design presented maximizes direct recycling of hydrogen isotopes from the fusion chamber exhaust to the fueling system while minimizing IRPR system steady-state tritium inventory. The optimized IRPR distillation column presented achieves direct recycling of 60 % of the hydrogen isotopes in the fusion chamber exhaust with an estimated steady-state system tritium inventory <30 g. In conclusion, the optimized IRPR distillation column operation was then used to estimate the design requirements for a detritation column to treat the IRPR system effluent stream.

CryOgenic distillation↗
DOE OSTI2021

Lithium, a path to make fusion energy affordable

In this tutorial article, we review the technological, physics, and economic basis for a magnetic fusion device utilizing a flowing liquid lithium divertor (molten metal velocity in the range of cm/s) and operating in a low-recycling plasma regime. When extrapolated to magnetic fusion reactor scale, the observed effects of a liquid lithium boundary on recycling reduction, confinement increase, and anomalous heat transport mitigation may offer a fundamentally distinct and promising alternative route to fusion energy production. In addition, this lithium-driven low recycling regime could accelerate fusion’s commercial viability since such a device would be smaller, dramatically decreasing plant and electricity costs if all technological complexities are solved. First, the theoretical basis of the energy confinement and fusion performance as well as the related possibilities of low recycling regimes driven by flowing lithium plasma-facing components are reviewed. Then the paper emphasizes the technological obstacles that need to be overcome for developing the necessary systems for such a flowing liquid lithium solution at reactor scale and details how many of these have been overcome at laboratory and/or proof-of-concept scale. Finally, the current and planned scientific and engineering endeavors being performed at the University of Illinois at Urbana-Champaign regarding this alternative reactor option are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Fusion Energy Research at Idaho National Laboratory: Experimentation and Simulation to Support Safety and Rapid Technology Development

Research into fusion energy is growing rapidly, responding to a call for sustainable sources of energy to replace fossil fuels and mitigate climate change. Within the United States, at least, researchers are also responding to the “Bold Decadal Vision” proposed by the White House, seeking to have a commercially relevant fusion pilot plant deployed within a decade. Before this can become a reality, many Fusion Science & Technology (FS&T) gaps remain. For over 45 years, Idaho National Laboratory has been at the forefront of addressing these FS&T gaps in the context of fusion safety and technology via the operation of world-leading experimental facilities within the Safety and Tritium Applied Research (STAR) Facility. Here, INL focuses on the tritium fuel cycle, conceptual system design studies, risk assessment, waste management, and materials safety. Modeling and Simulation (M&S) has also been a component of this portfolio of research, but, early on, focused on individual systems. Since 2019, active development and research on integrated whole device modeling tools based on the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework has been undertaken. This has culminated in a MOOSE-based version of the Tritium Migration and Analysis Program (TMAP), an INL code historically focused on tritium permeation and trapping within fusion systems. More recently, INL Laboratory Directed Research and Development funds have been used to create the Fusion ENergy Integrated multiphys-X (FENIX) code focused on scrape-off layer plasma physics and the first wall of a magnetically confined fusion device. This talk will focus on an overview of INL activities in the FS&T research area, with a particular focus on recent M&S activities and results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Investigation of a gallium alloy liquid metal mirror for application in inertial fusion energy systems

The final optic in future inertial fusion energy plants must maintain high performance and survivability under gigashot laser irradiation while exposed to fusion byproducts. Although no practical solution has been demonstrated, a self-healing final turning mirror based on a grazing-incidence liquid metal mirror has been theoretically explored. This work investigates the suitability of a gallium alloy. The experimental system simulates key conditions, including vacuum exposure and 10-Hz, 355-nm, and 6-ns laser pulses. Experiments address reflectivity, damage, and response as a function of pressure. Results highlight the potential of liquid metal gallium alloys for robust final optics in laser-based fusion power plants and inform non-traditional optics for intense laser systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Calculating Reactivity and Fusion Energy Yield

During my time at Lawrence Livermore National Lab, I had the opportunity to intern at the HEDS (High Energy Density Science) Center and become an IFE (Inertial Fusion Energy) summer student for three weeks with Dr. Veronika Kruse as my mentor. Within this time frame, my research project’s goal was to develop an understanding of nuclear fusion while building technical skills in calculating and analyzing the required data. The following report outlines the process of calculating reactivity curves and energy yields of specific fusion reactions. For context, nuclear fusion is when two atomic nuclei combine, and energy is released. NIF (the National Ignition Facility), located at LLNL, uses laser-based inertial confinement fusion to achieve ignition. To simplify the process, NIF uses lasers to heat a small sphere or capsule, made up of primarily deuterium and tritium, to extremely high temperatures and densities to achieve fusion ignition, where more energy is released than the lasers introduced.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

The staged Z-pinch as a potential fusion energy source

A staged Z-pinch is a fusion concept where a high atomic number liner compresses a fusion fuel (deuterium–deuterium or deuterium–tritium) target. Here, we report new results from Lagrangian, Eulerian, and Arbitrary Lagrangian–Eulerian simulations, which confirm that, with proper treatment of the vacuum region outside from the pinch, fusion energy production >1 MJ can be expected without alpha heating and significantly higher if alpha heating is included. It is shown that shock waves play an important role in preheating the target plasma and in piling up liner mass at the liner/target interface. This results in higher ram pressure just before the pinch stagnation time and ultimately in higher energy density target plasma.

Ruskov, E. (ORCID:0000000336724580)↗
DOE OSTI2024

Extension of Virtual Test Bed Advanced Modeling and Simulation Capabilities for Fusion Energy

The National Reactor Innovation Center (NRIC) was established to accelerate the deployment of novel reactor concepts. This is achieved by providing physical and virtual spaces for building and testing reactor experiments. The Virtual Test Bed (VTB) represents the virtual counterpart to the physical test beds. It is a collaboration with the Department of Energy’s (DOE) Nuclear Energy Advanced Modeling and Simulation (NEAMS) program with the mission to accelerate the deployment of advanced reactors by facilitating the adoption of advanced modeling and simulation (M&S) tools developed by the DOE. This mission has been carried out by the VTB since 2020 by hosting and featuring dozens of advanced fission nuclear reactor models developed by national laboratories and academia. The charter of the NRIC’s definition of advanced reactors also includes fusion nuclear reactors. As the tools developed by the NEAMS program are increasingly used for modeling fusion energy devices, there is an increasing need to host fusion reactor models on the VTB repository. The VTB will be extended in 2024 to support fusion energy modeling and simulation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Laser driven inertial fusion energy technology development

The future of Laser-Based Inertial fusion energy requires the development of efficient diode-pumped laser drivers that can be scaled to megajoule class output operating at ≥ 10-Hz repetition rate. ARPA-E requested a study of the range of possibilities for a 100kJ/10-Hz laser system with >15% wall-plug efficiency operating below 360 nm. The conceptual design of a compact, 1 kJ class module is presented and analyzed for performance relative to the objectives along with a roadmap to demonstrate the technology.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Robustness of inertial fusion energy relevant implosions to low-mode asymmetries

Inertial confinement fusion implosions for power production need to be robust. Degradation sources need to be understood and considered for an economic power plant. In this work, the impact of low-mode asymmetries on yield is studied using 2D radiation hydrodynamics simulations for inertial fusion energy relevant implosions. First, a high-gain indirectly driven capsule design is developed. This design is subsequently degraded with low-mode drive asymmetries. The results show that yield is constant with increasing amounts of asymmetry until a cliff is reached where the yield quickly drops below ignition. Robustness arises because the degraded hotspot still has enough time to get to ignition before capsule decompression. This robustness occurs even though the asymmetry couples less energy to the hotspot and causes decompression to occur sooner. The robustness is linked to the generalized Lawson parameter, χ⁠. The value of χ steadily decreases with increasing asymmetry. Once χ is close to one, the hotspot is no longer able to ignite before the capsule decompresses. A simple piston model is used to predict where the robustness cliff is for any design. The trade-off between yield and robustness is also demonstrated.

Physics - Plasma physics↗
DOE OSTI2025

Determining the nanostructure of polymer foams using 3D ptycho-tomography for inertial fusion energy applications

Polymer foams play a critical role in contemporary inertial fusion energy (IFE) target designs by enhancing energy yield and optimizing implosion dynamics. However, the lack of high-resolution characterization of the nanostructure of these foams restricts progress in fusion science. In this work, we demonstrate the first high-resolution three-dimensional (3D) reconstruction of a low-density, Si-doped polymer foam fabricated via two-photon polymerization, using ptychographic x-ray computed tomography (PXCT) at an x-ray free electron laser (XFEL). This imaging method reconstructs two-dimensional (2D) attenuation and phase information at multiple sample angles that are combined into a 3D density map used to extract local mass density and determine structural dimensions. We achieve a 2D spatial resolution of 19 ± 3 nm on a high-contrast Ronchi pattern target and 78.7 ± 3 nm for low-contrast polymer foams, marking a significant advancement for XFEL-based ptychography of low-density materials. Furthermore, our experimental results reveal an average foam strut thickness of 1.17 ± 0.4 μm, consistent with fabrication expectations, and a reconstructed average mass density of 0.35 g/cc, aligning closely with the predicted density of 0.29 g/cc. These findings provide important insights for improving foam design and refining radiation hydrodynamics modeling in future IFE experiments. Our study establishes PXCT at an XFEL as a powerful tool for high-resolution characterization of fusion-relevant materials, paving the way for enhanced target performance in IFE research.

Hancock, Levi [Colorado State Univ., Fort Collins,↗
DOE OSTI2022

Physics-based model of irradiation creep for ferritic materials under fusion energy operation conditions

Irradiation creep is known to be an important process for structural materials in nuclear environments, potentially leading to creep failure at temperatures where thermal creep is generally negligible. While there is a great deal of data for irradiation creep in steels and zirconium alloys in light water reactor conditions, much less is known for first wall materials under fusion energy conditions. Lacking suitable fusion neutron sources for detailed experimentation, modeling, and simulation can help bridge the dose-rate and spectral-effects gap and produce quantifiable expectations for creep deformation of first wall materials under standard fusion conditions. In this paper, we develop a comprehensive model for irradiation creep created from merging a crystal plasticity representation of the dislocation microstructure and a defect evolution simulator that accounts for the entire cluster dimensionality space. Both approaches are linked by way of a climb velocity that captures dislocation-biased defect absorption and a dislocation strengthening term that reflects the accumulation of defect clusters in the system. Here, we carry out our study in Fe under first wall fusion reactor conditions, characterized by a fusion neutron spectrum with average recoil energies of 20 keV and a damage dose rate of ≈3×10 –7 dpa/s at temperatures between 300 and 800 K.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Directly driven magnetized fast-ignition targets with steep density gradients for inertial fusion energy

The development of advanced targets capable of achieving ignition with improved energy gain at lower driver energies is one of four key technical challenges to be solved in order to realize economical inertial fusion energy. We report the minimum energy necessary for a small hemispherical mass of fast-ignited high-density deuterium–tritium fuel to explosively ignite a significantly larger hemispherical mass of assembled cold fuel with much lower mass density, both with and without a flux-compressed magnetic field connecting the two regions. With the magnetic field, the burn rate improves, and lower energy states become more effective. The imploded fuel reservoir available in the lower-density, larger-mass region of the steep density gradient determines whether the fusion yield is several hundred MJ or up to a few GJ. We report a case wherein the cold reservoir ignited and produced high gain with the assistance of only ~700 kJ of hotspot yield, an amount that has already been demonstrated as feasible in laboratory experiments using indirect-drive targets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Fusion energy technology and design-specific safety considerations

Design of commercial fusion energy technology must be done in a manner safe to the general public. This presentation is intended to cover the major non-radiological categories which must be considered for adequate safety of fusion devices.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Fusion energy technology and design-specific safety considerations

Design of commercial fusion energy technology must be done in a manner safe to the general public. This presentation is intended to cover the major non-radiological categories which must be considered for adequate safety of fusion devices.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

DIII-D research advancing the physics basis for optimizing the tokamak approach to fusion energy

DIII-D physics research addresses critical challenges for the operation of ITER and the next generation of fusion energy devices. This is done through a focus on innovations to provide solutions for high performance long pulse operation, coupled with fundamental plasma physics understanding and model validation, to drive scenario development by integrating high performance core and boundary plasmas. Substantial increases in off-axis current drive efficiency from an innovative top launch system for EC power, and in pressure broadening for Alfven eigenmode control from a co-/counter-I p steerable off-axis neutral beam, all improve the prospects for optimization of future long pulse/steady state high performance tokamak operation. Fundamental studies into the modes that drive the evolution of the pedestal pressure profile and electron vs ion heat flux validate predictive models of pedestal recovery after ELMs. Understanding the physics mechanisms of ELM control and density pumpout by 3D magnetic perturbation fields leads to confident predictions for ITER and future devices. Validated modeling of high-Z shattered pellet injection for disruption mitigation, runaway electron dissipation, and techniques for disruption prediction and avoidance including machine learning, give confidence in handling disruptivity for future devices. For the non-nuclear phase of ITER, two actuators are identified to lower the L–H threshold power in hydrogen plasmas. With this physics understanding and suite of capabilities, a high poloidal beta optimized-core scenario with an internal transport barrier that projects nearly to Q = 10 in ITER at ~8 MA was coupled to a detached divertor, and a near super H-mode optimized-pedestal scenario with co-I p beam injection was coupled to a radiative divertor. The hybrid core scenario was achieved directly, without the need for anomalous current diffusion, using off-axis current drive actuators. Also, a controller to assess proximity to stability limits and regulate β N in the ITER baseline scenario, based on plasma response to probing 3D fields, was demonstrated. Finally, innovative tokamak operation using a negative triangularity shape showed many attractive features for future pilot plant operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Preliminary neutronic and thermal analysis of Inertial Fusion Energy systems with a focus on thick liquid wall concepts

This paper provides an assessment of the neutronic behavior of Inertial Fusion Energy systems using the Serpent 2 Monte Carlo code. The study explores different types of reactor concepts, including dry-wall and thick liquid wall systems. In particular, it characterizes the tritium breeding and energy multiplication performance, as well as the effect of long-term irradiation on structural materials. For this purpose, the displacement per atom (DPA) and the gas production rate in structural materials are calculated. A simplified geometry with varying geometrical parameters is used as a representation for the different kinds of devices. Additionally, the case of the HYLIFE-II concept is used to assess modeling inaccuracies arising from certain approximations. A comparison between the simplified geometry and a realistic one is performed, thanks to Serpent’s capability to run transport calculations on unstructured meshes. The study then addresses the impact of these discrepancies on the temperature distribution in the first wall using the GeN-Foam code for conjugate heat transfer analysis. The results highlight the necessity to consider the heterogeneous nature of the liquid wall, as simplified models tend to underestimate radiation damage metrics and heat loads.

Conjugate heat transfer↗