Search NASA⌕ Search

SEARCH · Search NASA

Results for “HVPE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

49 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

X-ray topography characterization of gallium nitride substrates for power device development

Gallium nitride substrates grown by the hydride vapor phase epitaxy (HVPE) method using a patterned growth process have been characterized by synchrotron monochromatic beam X-ray topography in the grazing incidence geometry. Images reveal a starkly heterogeneous distribution of dislocations with areas as large as 0 3 mm 2 containing threading dislocation densities below 10 3 cm -2 in between a grid of strain centers with higher threading dislocation densities (> 10 4 cm -2 ). Basal plane dislocation densities in these areas are as low as 104 cm -2 . By comparing the recorded images of dislocations with ray tracing simulations of expected dislocations in GaN, the Burgers vectors of the dislocations have been determined. The distribution of threading screw/mixed dislocations (TSDs/TMDs), threading edge dislocations (TEDs) and basal plane dislocations (BPDs) is discussed with implications for fabrication of power devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Large area vertical Ga 2 O 3 Schottky diodes for X-ray detection

In this work, the Schottky barrier diodes were fabricated from a bulk Sn-doped (001) n-type Ga 2 O 3 substrate with a Si-doped epitaxial layer grown by hydride vapor phase epitaxy (HVPE), which demonstrate a good response to X-rays. Circular metal contacts with diameters ranging from 50 to 1500 um and square metal contacts ranging from 100 X 100 to 1600 X 1600 um 2 were deposited on the wafer. The devices were characterized for their electrical performance including forward current–voltage (FIV), reverse current–voltage (RIV), and capacitance-voltage (CV) measurements. The best device showed a breakdown voltage of –804 V and the devices tested had an average ideality of 1.12. The devices exhibited a clear response to X-rays even at zero bias with an experimentally observed response time 1.03 s and a linear response of detector signal to the X-ray dose rate. The experimentally observed device response time improved to 0.25 s when bias voltage is applied. The device also survived a long-term stability test of over 2 h under a constant X-ray irradiation. The sensitivity and the lower limit of detection for X-ray by Ga2O3 epitaxial Schottky detectors were discussed and determined as 43.5 C/mGy cm –2 at –200 V and 8.31 nGy Air /s, respectively.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Control of Surface Morphology during the Growth of (110)-Oriented GaAs by Hydride Vapor Phase Epitaxy

We present a study of the effect of hydride vapor phase epitaxy (HVPE) growth conditions on the morphology of GaAs grown on vicinal and nominally exact (110) GaAs substrates. We evaluate epilayer surfaces using a combination of Nomarski microscopy and atomic force microscopy. The surface morphology strongly depends on the growth conditions employed, as well as the substrate orientation. On substrates offcut 3° toward (111)A, faceting generally develops under conditions in which the growth is Ga-limited, although Ga-limited growth is not the only requirement for faceting. Low growth temperatures lead to a faceted morphology, while higher growth temperatures favor smooth growth and facet-free morphology. We show that the surface morphology is kinetically controlled and that the tendency to facet correlates with the growth rate. 3D growth occurs on nominally exact substrates, resulting in hillock formation, but reduction of the group V precursor partial pressure results in smooth morphology. Overall, our results are consistent with models for step-bunching-induced surface faceting that invoke a negative Ehrlich–Schwoebel step-edge barrier.

(110) oriented GaAs↗
DOE OSTI2023

Plasma-assisted deposition and characterization of Al 2 O 3 dielectric layers on (001) β -Ga 2 O 3

In this work, we have investigated plasma-assisted deposition of Al 2 O 3 on HVPE (001) β-Ga 2 O 3 and evaluated the dielectric quality from electrical measurements on fabricated metal-oxide-semiconductor (MOS) capacitors. The interface structure and crystallinity of the films were investigated as a function of the growth temperature. The dielectric/semiconductor interfaces were found to have reverse breakdown electric fields up to 5.3 MV/cm in the β-Ga 2 O 3 , with relatively low hysteresis in capacitance–voltage and low leakage current. We determined a negative fixed interface charge density at the interface from analysis of thickness-dependent capacitance voltage data. In conclusion, this study shows the advantage of using plasma-assisted deposition to achieve high breakdown strength Al 2 O 3 /β-Ga 2 O 3 MOS structures for device application purposes.

42 ENGINEERING↗
DOE OSTI2020

A study on the impact of mid-gap defects on vertical GaN diodes

GaN is a favorable martial for future efficient high voltage power switches. GaN has not dominated the power electronics market due to immature substrate, homoepitaxial growth, and immature processing technology. Understanding the impact of the substrate and homoepitaxial growth on the device performance is crucial for boosting the performance of GaN. Here, we studied vertical GaN PiN diodes that were fabricated on non-homogenous Hydride Vapor Phase Epitaxy (HVPE) substrates from two different vendors. We show that defects which stemmed from growth techniques manifest themselves as leakage hubs. Different non-homogenous substrates showed different distribution of those defects spatially with the lesser quality substrates clustering those defects in clusters that causes pre-mature breakdown. Energetically these defects are mostly mid-gap around 1.8Ev with light emission spans from 450nm to 700nm. Photon emission spectrometry and hyperspectral electroluminescence were used to locate these defects spatially and energetically.

42 ENGINEERING↗
DOE OSTI2023

Adroit Materials Final Scientific/Technical Report kV-class GaN-based Junction Barrier Schottky diodes using ion implantation

The primary aim of this research was to develop GaN-based Junction Barrier Schottky (JBS) diodes using an innovative ion implantation process previously established in ARPA-E funded projects. The central focus of our proposed technology revolves around selective area p-type doping, accomplished through the implantation of Mg ions. This approach builds upon our successes in the ARPA-E PNDIODES program, advancing towards commercial device integration. Selective area p-doping plays a pivotal role in realizing the next generation of GaN-based power devices, capable of significantly reducing the carbon footprint in the United States by several million tons. While ion implantation is a well-established technique for achieving selective area doping in SiC and Si materials, its feasibility in GaN had not been demonstrated until now. To fabricate high voltage GaN JBS diodes, we initially created thick n-type drift layers with high carrier concentrations ranging from 5×1015 cm-3 to 2×1016 cm-3 and very high mobilities. Subsequently, Mg ions were selectively implanted to form p-type islands within the n-type drift layer. To reduce electric field crowding at the edge of the diode and to achieve high breakdown voltage, junction edge termination (JTE) and floating field rings (FFRs) were formed using Mg implantation. A high temperature, high-pressure post-implantation annealing process was carried out to activate the implanted Mg ions. As a result, we were able to demonstrate GaN JBS diodes with a breakdown voltage of 915 V and an on-resistance of 0.6 mΩ·cm2. These diodes exhibited a forward bias current density of 1 kA/cm2 at 1.5 V. Subsequently, we achieved GaN JBS diodes with a remarkable breakdown voltage of 1900 V and an on-resistance of 1.9 mΩ·cm2, capable of sustaining a forward bias current density of 0.5 kA/cm2 at 1.5 V. Importantly, the ON and OFF state performance of these GaN JBS diodes surpassed that of Si and SiC-based power diodes reported in existing literature. Lastly, we successfully grew 60 μm thick GaN:Si layers using HVPE with a carrier concentration of approximately 3 to 5×1015 cm-3. Based on simulation and empirical data these devices represent 5 kV GaN JBS power diodes, leveraging the developed processes in this project.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Epitaxial Growth of Ga2O3: A Review

Beta-phase gallium oxide (β-Ga2O3) is a cutting-edge ultrawide bandgap (UWBG) semiconductor, featuring a bandgap energy of around 4.8 eV and a highly critical electric field strength of about 8 MV/cm. These properties make it highly suitable for next-generation power electronics and deep ultraviolet optoelectronics. Key advantages of β-Ga2O3 include the availability of large-size single-crystal bulk native substrates produced from melt and the precise control of n-type doping during both bulk growth and thin-film epitaxy. A comprehensive understanding of the fundamental growth processes, control parameters, and underlying mechanisms is essential to enable scalable manufacturing of high-performance epitaxial structures. This review highlights recent advancements in the epitaxial growth of β-Ga2O3 through various techniques, including Molecular Beam Epitaxy (MBE), Metal-Organic Chemical Vapor Deposition (MOCVD), Hydride Vapor Phase Epitaxy (HVPE), Mist Chemical Vapor Deposition (Mist CVD), Pulsed Laser Deposition (PLD), and Low-Pressure Chemical Vapor Deposition (LPCVD). This review concentrates on the progress of Ga2O3 growth in achieving high growth rates, low defect densities, excellent crystalline quality, and high carrier mobilities through different approaches. It aims to advance the development of device-grade epitaxial Ga2O3 thin films and serves as a crucial resource for researchers and engineers focused on UWBG semiconductors and the future of power electronics.

Chemistry↗
DOE OSTI2025

Halide Vapor Phase Epitaxy of Ge from an Elemental Source

Halide vapor phase epitaxy shows promise for low-cost photovoltaic device manufacturing because of its high growth rates and lower cost elemental precursors but previously has not been used to deposit epitaxial Ge. Here, we demonstrate Ge deposition by generating GeCl 2 in situ from solid Ge and HCl in a N 2 ambient. To achieve Ge growth, we inject AsH 3 and PH 3 as sources of active hydrogen to the growth surface to create a driving force for growth. We do not observe Ge growth unless a supply of hydrogen is added, consistent with thermodynamic calculations. Furthermore, we show the hydrogen source must crack readily on the substrate surface to enable growth; relatively stable sources such as H 2 do not cause growth. Unintentional group V doping is one drawback of using AsH 3 and PH 3 to drive the Ge reaction. We observed As or P concentrations in the Ge films ranging from 4 x 10 17 to 1 x 10 18 atoms/cm 3 , concentrations that can drastically influence device characteristics. However, we note there are numerous other "helper molecule" options that can provide active hydrogen without doping or etching the material. This work provides a path forward for Ge deposition for optoelectronic devices from an elemental source.

14 SOLAR ENERGY↗
DOE OSTI2020

GaAs growth rates of 528 μm/h using dynamic-hydride vapor phase epitaxy with a nitrogen carrier gas

Herein we demonstrate record GaAs growth rates approaching 530 μm/h using nitrogen carrier gas and 400 μm/h using hydrogen carrier gas in a dynamic-hydride vapor phase epitaxy reactor. We measured root mean square surface roughness below 1 nm using a 1 μm × 1 μm atomic force microscopy scan for GaAs growth rates up to 483 μm/h using a nitrogen carrier gas and 400 μm/h using a hydrogen carrier gas. We performed computational fluid dynamics modeling to study the effect of the carrier gas choice on the thermal profile within the reactor and how that influences the degree of AsH 3 decomposition. The modeling suggests that the lower thermal conductivity of the nitrogen carrier gas minimizes the amount of AsH 3 that thermally decomposes before reaching the wafer surface and the heavier atomic mass decreases the likelihood that AsH 3 will reach the heated reactor walls, leading to a growth rate enhancement relative to the hydrogen carrier case in a hydride-enhanced growth regime.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Ultrawide bandgap semiconductor h-BN for direct detection of fast neutrons

III-nitride wide bandgap semiconductors have contributed on the grandest scale to many technological advances in lighting, displays, and power electronics. Among III-nitrides, BN has another unique application as a solid-state neutron detector material because the isotope B-10 is among a few elements that have an unusually large interaction cross section with thermal neutrons. A record high thermal neutron detection efficiency of 60% has been achieved by B-10 enriched h-BN detectors of 100 μm in thickness in our group. However, direct detection of fast neutrons with energies above 1 MeV is highly challenging due to the extremely low interaction cross section of fast neutrons with matter. We report the successful attainment of 0.4 mm thick freestanding h-BN 4"-diameter wafers, which enabled the demonstration of h-BN fast neutron detectors capable of delivering a detection efficiency of 2.2% in response to a bare AmBe neutron source. Furthermore, it was shown that the energy information of incoming fast neutrons is retained in the neutron pulse-height spectra. A comparison of characteristics between h-BN fast and thermal neutron detectors is summarized. Neutron detectors are vital diagnostic instruments for nuclear and fusion reactor power and safety monitoring, oil field exploration, neutron imaging and therapy, as well as for plasma and material science research. With the outstanding attributes resulting from its ultrawide bandgap (UWBG), including the ability to operate at extreme conditions of high power, voltage, and temperature, the availability of h-BN UWBG semiconductor detectors with the capability of simultaneously detecting thermal and fast neutrons with high efficiencies is expected to open unprecedented applications that are not possible to attain by any other types of neutron detectors.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of Doping Density on the Performance of Metamorphic GaInAs Solar Cells Grown by Dynamic Hydride Vapor Phase Epitaxy

We study the effect of doping density on the performance of inverted metamorphic ~1 eV GaInAs solar cells grown by dynamic hydride vapor phase epitaxy. We find that the doping efficiency of Se in this material is extremely high, with 5x10 17 cm -3 being the lowest controlled value we could achieve with our present Se source. We compared rear heterojunction devices grown with intentional n-doping of 5x10 17 cm -3 and unintentional n-doping of 5x10 15 cm -3 . The intentionally doped sample exhibited an open circuit voltage ~80 mV higher than the unintentionally doped sample due to reduced dark current, and a bandgap voltage offset, or W OC , of 0.407 V. We believe that future doping optimization will improve carrier collection and W OC in these devices.

GaAs↗