Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ice Accretion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Large-Drop Ice Accretion Test Results for a Large Scale Swept Wing Section

In-flight icing is an important consideration that affects aircraft design, performance and safety. Newer regulations combined with increasing demand to reduce fuel burn, emissions and noise are driving a need for improvements in icing simulation capability. To that end, this paper presents the results of ice accretion testing conducted in the NASA Icing Research Tunnel on a large swept wing typical of a modern commercial transport. The model was based upon a section of the Common Research Model wing at the 64% semispan station with a streamwise chord length of 136 in. The test conditions were developed with an icing scaling analysis to generate similar conditions for a small MVD = 25 μm and a large MVD = 110 μm. A series of tests were conducted over a range of total temperature from -23.8 ˚C to -1.4 ˚C with all other conditions held constant. The results for the small MVD cloud conditions were consistent with previous work and showed the changing ice morphology from rime ice at colder temperatures to highly 3D scallop ice in the range of -8.7 ˚C to -3.8 ˚C. The results for the large MVD cloud conditions exhibited some differences in the ice accretion morphology. Scallop-like ice features were observed at total temperature of -3.8˚C. The large MVD ice accretion at lower temperatures tended to be smoother than the corresponding ice accretion for small MVD. The thickness of the main ice shape tended to be larger for the small MVD conditions compared to the corresponding large MVD ice shape while the latter had more ice farther downstream. The measured ice mass was approximately equal between the corresponding small and large MVD ice shapes up to a freezing fraction of 0.6. For higher freezing fraction, the large MVD ice shapes weighed more. Cloud MVD variation from 50 μm to 230 μm while holding the scaling parameters constant resulted in very minor differences in the ice shapes, mostly in the upper and lower surface chordwise extents. Ice volume was computed from 3D scan data and used to calculate a ratio of ice mass to volume. The resulting values were in the range of 240 to 455 Kg/m3. While this is consistent with analogous values previously reported in the literature, more data are needed to determine a specific trend in this ratio as a function of freezing fraction and the corresponding governing physical phenomena. This work has resulted in a significant experimental database of ice accretion for small and large MVD conditions applicable to large-scale swept wings.

Icing↗
NASA NTRS1989

An experimental investigation of multi-element airfoil ice accretion and resulting performance degradation

An investigation of the ice accretion pattern and performance characteristics of a multi-element airfoil was undertaken in the NASA Lewis 6- by 9-Foot Icing Research Tunnel. Several configurations of main airfoil, slat, and flaps were employed to examine the effects of ice accretion and provide further experimental information for code validation purposes. The text matrix consisted of glaze, rime, and mixed icing conditions. Airflow and icing cloud conditions were set to correspond to those typical of the operating environment anticipated tor a commercial transport vehicle. Results obtained included ice profile tracings, photographs of the ice accretions, and force balance measurements obtained both during the accretion process and in a post-accretion evaluation over a range of angles of attack. The tracings and photographs indicated significant accretions on the slat leading edge, in gaps between slat or flaps and the main wing, on the flap leading-edge surfaces, and on flap lower surfaces. Force measurments indicate the possibility of severe performance degradation, especially near C sub Lmax, for both light and heavy ice accretion and performance analysis codes presently in use. The LEWICE code was used to evaluate the ice accretion shape developed during one of the rime ice tests. The actual ice shape was then evaluated, using a Navier-Strokes code, for changes in performance characteristics. These predicted results were compared to the measured results and indicate very good agreement.

Potapczuk, Mark G.↗
NASA NTRS1989

An experimental investigation of multi-element airfoil ice accretion and resulting performance degradation

An investigation of the ice accretion pattern and performance characteristics of a multi-element airfoil was undertaken in the NASA Lewis 6- by 9-Foot Icing Research Tunnel. Several configurations of main airfoil, slat, and flaps were employed to examine the effects of ice accretion and provide further experimental information for code validation purposes. The text matrix consisted of glaze, rime, and mixed icing conditions. Airflow and icing cloud conditions were set to correspond to those typical of the operating environment anticipated for a commercial transport vehicle. Results obtained included ice profile tracings, photographs of the ice accretions, and force balance measurements obtained both during the accretion process and in a past-accretion evaluation over a range of angles of attack. The tracings and photographs indicated significant accretions on the slat leading edge, in gaps between slat or flaps and the main wing, on the flap leading-edge surfaces, and on flap lower surfaces. Force measurements indicate the possibility of severe performance degradation, especially near C sub Lmax, for both light and heavy ice accretion and performance analysis codes presently in use. The LEWICE code was used to evaluate the ice accretion shape developed during one of the rime ice tests. The actual ice shape was then evaluated, using a Navier-Strokes code, for changes in performance characteristics. These predicted results were compared to the measured results and indicate very good agreement.

Potapczuk, Mark G.↗
NASA NTRS2000

Geometry Modeling and Grid Generation for "Icing Effects" and "Ice Accretion" Simulations on Airfoils

There are two distinct icing-related problems for airfoils that can be simulated. One is predicting the effects of ice on the aerodynamic performance of airfoils when ice geometry is known ("icing effects" study). The other is simulating ice accretion under specified icing conditions ("ice accretion" simulation). This paper will address development of two different software packages for two-dimensional geometry preparation and grid generation for both "icing effects" and "ice accretion" studies.

Choo, Yung↗
NASA NTRSDate not supplied

Large-Drop Ice Accretion Test Results for a Large Scale Swept Wing Model

In-flight icing is an important consideration that affects aircraft design, performance and safety. Newer regulations combined with increasing demand to reduce fuel burn, emissions and noise are driving a need for improvements in icing simulation capability. To that end, this paper presents the results of ice accretion testing conducted in the NASA Icing Research Tunnel on a large swept wing section typical of a modern commercial transport. The model was based upon a section of the Common Research Model wing at the 64% semispan station with a streamwise chord length of 136 in. The test conditions were developed with an icing scaling analysis to generate similar conditions for a small MVD = 25 μm and a large MVD = 110 μm. A series of tests were conducted over a range of total temperature from -23.8 ˚C to -1.4 ˚C with all other conditions held constant. The results for the small MVD cloud conditions were consistent with previous work and showed the changing ice morphology from rime ice at colder temperatures to highly 3D scallop ice in the range of -8.7 ˚C to -3.8 ˚C. The results for the large MVD cloud conditions exhibited some differences in the ice accretion morphology from the small MVD conditions. Scallop-like ice features were observed at total temperature of -3.8˚C. The large MVD ice accretion at lower temperatures tended to be smoother than the corresponding ice accretion for small MVD. The thickness of the main ice shape tended to be larger for the small MVD conditions compared to the corresponding large MVD ice shape while the latter had more ice farther downstream. The measured ice mass was approximately equal between the corresponding small and large MVD ice shapes up to a freezing fraction of 0.6. For higher freezing fraction, the large MVD ice shapes weighed more. Cloud MVD variation from 50 μm to 230 μm while holding the scaling parameters constant resulted in very minor differences in the ice shapes, mostly in the upper and lower surface chordwise extents. Ice volume was computed from 3D scan data and used to calculate a ratio of ice mass to volume. The resulting values were in the range of 240 to 455 Kg/m3. While this is consistent with analogous values previously reported in the literature, more data are needed to determine a specific trend in this ratio as a function of freezing fraction and the corresponding governing physical phenomena. This work has resulted in a significant experimental database of ice accretion for small and large MVD conditions applicable to large-scale swept wings.

Icing↗
NASA NTRS1983

Numerical simulation of airfoil ice accretion

A mathematical model of glaze and rime ice accretion on a two-dimensional airfoil is presented. The model employs standard methods for calculating the flow field and cloud droplet trajectories. This data is used as input to a thermodynamic analysis of the ice accretion process which includes liquid runback. The structure of the model allows for dynamic updating of the droplet collection efficiency and heat and mass transfer processes as the accreted ice shape changes. This results in the improved shape prediction over previously described methods. Simulations made with the model are compared to experimental results obtained for a NACA 0012 airfoil in the NASA/Lewis Icing Research Tunnel. The agreement with experiment is found to be generally satisfactory for some cases, but a need for improvements is indicated by others. Suggestions for improvements are made.

Macarthur, C. D.↗
NASA NTRS2000

Software Released by LEWICE 2.0 Ice Accretion Software Development Project

Computational icing simulation methods are making the transition from the realm of research to commonplace use in design and certification. As such, standards of software management, design, validation, and documentation must be adjusted to accommodate the increased expectations of the user community with respect to accuracy, reliability, capability, and usability. With this in mind, in collaboration with Glenn's Engineering Design and Analysis Division, the Icing Branch of the NASA Glenn Research Center at Lewis Field began a software improvement project focused on the two-dimensional ice accretion simulation tool LEWICE. This project is serving as an introduction to the concepts of software management and is intended to serve as a pilot project for future icing simulation code development. The LEWICE 2.0 Software Development Project consisted of two major elements: software management and software validation. The software management element consisted of identifying features of well-designed and well-managed software that are appropriate for an analytical prediction tool such as LEWICE and applying them to a revised version of the code. This element included tasks such as identification of software requirements, development and implementation of coding standards, and implementation of software revision control practices. With the application of these techniques, the LEWICE ice accretion code became a more stable and reliable software product. In addition, the lessons learned about software development and maintenance can be factored into future software projects at the outset. The software validation activity was an integral part of our effort to make LEWICE a more accurate and reliable analysis tool. Because of the efforts taken to extensively validate this software, LEWICE 2.0 is more robust than previous releases and can reproduce results accurately across several computing platforms. It also differs from previous versions in the extensive quantitative comparisons of its results with a data base of ice shapes that were generated in Glenn's Icing Research Tunnel. The results of the shape comparisons were analyzed to determine the range of meteorological conditions under which LEWICE 2.0 is within the repeatability found for ice shapes obtained from experiments. These comparisons show that the average variation of LEWICE 2.0 from experimental data is 7.2 percent, whereas the overall variability of the experimental data is 2.5 percent. The LEWICE 2.0 Software Development Project resulted in the release, at the recent Icing Branch LEWICE Workshop, of a more useful and robust analysis tool than was previously available to the icing community. The lessons learned from this project will be applied to the Icing Branch s future software development efforts.

Potapczuk, Mark G.↗
NASA NTRS2014

Implementation and Validation of 3-D Ice Accretion Measurement Methodology

A research program has been implemented to develop and validate the use of a commercial 3-D laser scanning system to record ice accretion geometry in the NASA Icing Research Tunnel. A main component of the program was the geometric assessment of the 3- D laser scanning system on a 2-D (straight wing) and a 3-D (swept wing) airfoil geometries. This exercise consisted of comparison of scanned ice accretion to castings of the same ice accretion. The scan data were also used to create rapid prototype artificial ice shapes that were scanned and compared to the original ice accretion. The results from geometric comparisons on the straight wing showed that the ice shape models generated through the scan/rapid prototype process compared reasonably well with the cast shapes. Similar results were obtained with the geometric comparisons on the swept wing. It was difficult to precisely compare the scans of the cast shapes to the original ice accretion scans because the cast shapes appear to have shrunk during the mold/casting process by as much as 0.10-inch. However the comparison of the local ice-shape features were possible and produced better results. The rapid prototype manufacturing process was shown to reproduce the original ice accretion scan normally within 0.01-inch.

Icing↗
NASA NTRS1990

Users Manual for the NASA Lewis Ice Accretion Prediction Code (LEWICE)

LEWICE is an ice accretion prediction code that applies a time-stepping procedure to calculate the shape of an ice accretion. The potential flow field is calculated in LEWICE using the Douglas Hess-Smith 2-D panel code (S24Y). This potential flow field is then used to calculate the trajectories of particles and the impingement points on the body. These calculations are performed to determine the distribution of liquid water impinging on the body, which then serves as input to the icing thermodynamic code. The icing thermodynamic model is based on the work of Messinger, but contains several major modifications and improvements. This model is used to calculate the ice growth rate at each point on the surface of the geometry. By specifying an icing time increment, the ice growth rate can be interpreted as an ice thickness which is added to the body, resulting in the generation of new coordinates. This procedure is repeated, beginning with the potential flow calculations, until the desired icing time is reached. The operation of LEWICE is illustrated through the use of five examples. These examples are representative of the types of applications expected for LEWICE. All input and output is discussed, along with many of the diagnostic messages contained in the code. Several error conditions that may occur in the code for certain icing conditions are identified, and a course of action is recommended. LEWICE has been used to calculate a variety of ice shapes, but should still be considered a research code. The code should be exercised further to identify any shortcomings and inadequacies. Any modifications identified as a result of these cases, or of additional experimental results, should be incorporated into the model. Using it as a test bed for improvements to the ice accretion model is one important application of LEWICE.

Ruff, Gary A.↗
NASA NTRS1984

Measurement of local connective heat transfer coefficients of four ice accretion shapes

In the analytical study of ice accretions that form on aerodynamic surfaces (airfoils, engine inlets, etc.) it is often necessary to be able to calculate convective heat transfer rates. In order to do this, local convective heat transfer coefficients for the ice accretion shapes must be known. In the past, coefficients obtained for circular cylinders were used as an approximation to the actual coefficients since no better information existed. The purpose of this experimental study was to provide local convective heat transfer coefficients for four shapes that represent ice accretions. The shapes were tested with smooth and rough surfaces. The experimental method chosen was the thin-skin heat rate technique. Using this method local Nusselt numbers were determined for the ice shapes. In general it was found that the convective heat transfer was higher in regions where the model's surfaces were convex and lower in regions where the model's surfaces were concave. The effect of roughness was to increase the heat transfer in the high heat transfer regions by approximately 100% while little change was apparent in the low heat transfer regions.

Smith, M. E.↗
NASA NTRS1987

Structural properties of impact ices accreted on aircraft structures

The structural properties of ice accretions formed on aircraft surfaces are studied. The overall objectives are to measure basic structural properties of impact ices and to develop finite element analytical procedures for use in the design of all deicing systems. The Icing Research Tunnel (IRT) was used to produce simulated natural ice accretion over a wide range of icing conditions. Two different test apparatus were used to measure each of the three basic mechanical properties: tensile, shear, and peeling. Data was obtained on both adhesive shear strength of impact ices and peeling forces for various icing conditions. The influences of various icing parameters such as tunnel air temperature and velocity, icing cloud drop size, material substrate, surface temperature at ice/material interface, and ice thickness were studied. A finite element analysis of the shear test apparatus was developed in order to gain more insight in the evaluation of the test data. A comparison with other investigators was made. The result shows that the adhesive shear strength of impact ice typically varies between 40 and 50 psi, with peak strength reaching 120 psi and is not dependent on the kind of substrate used, the thickness of accreted ice, and tunnel temperature below 4 C.

Scavuzzo, R. J.↗
NASA NTRS2019

Experimental Aerodynamic Simulation of Glaze Ice Accretion on a Swept Wing

Aerodynamic assessment of icing effects on swept wings is an important component of a larger effort to improve three-dimensional icing simulation capabilities. An understanding of ice-shape geometric fidelity and Reynolds and Mach number effects on iced-wing aerodynamics is needed to guide the development and validation of ice-accretion simulation tools. To this end, wind-tunnel testing was carried out for 8.9% and 13.3% scale semispan wing models based upon the Common Research Model airplane configuration. Various levels of geometric fidelity of an artificial ice shape representing a realistic glaze-ice accretion on a swept wing were investigated. The highest fidelity artificial ice shape reproduced all of the three-dimensional features associated with the glaze ice accretion. The lowest fidelity artificial ice shapes were simple, spanwise-varying horn ice geometries intended to represent the maximum ice thickness on the wing upper surface. The results presented in this paper show that changes in Reynolds and Mach number have only a small effect on the iced-wing aerodynamics relative to the clean-wing configuration. Furthermore, the addition of grit roughness to some lower-fidelity artificial ice shapes resulted in favorable lift and pitching moment comparisons to the wing with the highest fidelity artificial ice shape. For the wing with simple horn ice shapes, the dependence of maximum lift coefficient on horn height and angle are generally consistent with the trends observed for similar experiments conducted on iced airfoils in past research. In terms of usable lift however, the horn height did have a significant effect even for lower horn angles. This could be an important finding since usable lift may be more indicative of the impending iced-swept wing stall and need for additional pitch control than maximum lift coefficient.

Broeren, Andy P.↗
NASA NTRS1989

The influence of ice accretion physics on the forecasting of aircraft icing conditions

The physics which control aircraft ice accretion are reviewed in the context of identifying and forecasting hazardous icing conditions. The severity of aircraft icing is found to be extremely sensitive to temperature, liquid water content and droplet size distribution particularly near the transition between rime and mixed icing. The difficulty in measurement and the variability of these factors with altitude, position and time coupled with variable aircraft sensitivity make forecasting and identifying icing conditions difficult. Automated Pilot Reports (PIREPS) are suggested as one mechanism for improving the data base necessary to forecast icing conditions.

Hansman, R. John, Jr.↗
NASA NTRS1990

The influence of ice accretion physics on the forecasting of aircraft icing conditions

The physics which control aircraft ice accretion are reviewed in the context of identifying and forecasting hazardous icing conditions. The severity of aircraft icing is found to be extremely sensitive to temperature, liquid water content and droplet size distribution particularly near the transition between rime and mixed icing. The difficulty in measurement and the variability of these factors with altitude, position and time coupled with variable aircraft sensitivity make forecasting and identifying icing conditions difficult. Automated Pilot Reports (PIREPS) are suggested as one mechanism for improving the data base necessary to forecast icing conditions.

Hansman, R. John, Jr.↗
NASA NTRS2018

Evaluation of a Thermodynamic Ice Crystal Icing Model Using Experimental Ice Accretion Data

This paper presents the evaluation of a thermodynamic ice crystal icing model, previously presented to describe the possible mechanisms of icing within the core of a turbofan jet engine. It has been proposed that there are two types of distinct ice accretions based on a surface energy balance: freeze-dominated icing and melt-dominated icing. In the former, ice accretion occurs where a freeze fraction (0 to 1) of melted ice crystals freezes on a surface, along with the existing ice of the impinging water and ice mass. This freeze-dominated icing is characterized by having strong adhesion to the surface. In the latter, icing occurs from accumulated unmelted ice on a surface, where a melt fraction (0 to 1) dictates the amount of unmelted impinged ice. This melt-dominated icing is characterized by weakly bonded surface adhesion. The experimentally observed ice growth rates suggest that only a small fraction of the impinging ice remains on the surface, implying a mass loss mechanism such as splash, runback, bounce, or erosion. This mass loss parameter must be determined in conjunction with the fraction of freezing liquid water or fraction of melting ice on an icing surface. This loss parameter, however, along with the freeze and melt fraction, are the only experimental parameters that are currently not measured directly. Using reported icing growth rates from published ice crystal icing experiments, a methodology is proposed to determine these unknown parameters. This work takes reported ice accretion data from tests conducted by the National Aeronautics and Space Administration (NASA) in 2016 and tests NASA collaborated on with the National Research Council (NRC) of Canada in 2012 that examined the fundamental physics of ice crystal icing. Those research efforts sought to generate icing conditions representative of those that occur inside a jet engine when ingesting ice crystals. This paper presents the fundamental equations of the thermodynamic model, the methodology used to determine the aforementioned unknown icing parameters, and results from model evaluation using experimental data. In addition, this paper builds on the previously proposed model by adding a transient conduction term to explain ice growth behavior at the onset of experimental tests that was observed to be different from steady-state ice growth that occurred later in the test run.With the addition of this energy term, this becomes a quasi-steady model. A key finding from this work suggests that mass loss fractions can exceed 0.90 for steady ice growth periods. In addition, due to conductive heat fluxes when using a warmer-than-freezing airfoil, lower mass loss fraction values were calculated during the initial transient period.

Ice-Crystal Ice Accretion↗
NASA NTRS2017

Ice Accretion Roughness Measurements and Modeling

Roughness on aircraft ice accretions is very important to the overall ice accretion process and to the resulting degradation in aircraft aerodynamic performance. Roughness enhances the local convection leading to more rapid ice accumulation rates, and roughness generates local flow perturbations that lead to higher skin friction. This paper presents 1) a review of the developments in ice shape three-dimensional laser scanning developed at NASA Glenn, 2) a review of the approach of McClain and Kreeger employed to characterize ice roughness evolution on an airfoil surface, and 3) a review of the experimental efforts that have been performed over the last five years to characterize, scale, and model ice roughness evolution physics.

SLD↗
NASA NTRS2016

Ice Accretion Test Results for Three Large-Scale Swept-Wing Models in the NASA Icing Research Tunnel

The design and certification of modern transport airplanes for flight in icing conditions increasing relies on three-dimensional numerical simulation tools for ice accretion prediction. There is currently no publically available, high-quality, ice accretion database upon which to evaluate the performance of icing simulation tools for large-scale swept wings that are representative of modern commercial transport airplanes. The purpose of this presentation is to present the results of a series of icing wind tunnel test campaigns whose aim was to provide an ice accretion database for large-scale, swept wings.

Wind-Tunnel Tests↗