Search NASA⌕ Search

SEARCH · Search NASA

Results for “Infrared techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Structural and magnetic properties of Sm{sub 2−x}Mn{sub x}O{sub 3} nanoparticles

Graphical abstract: - Highlights: • C-type Sm{sub 2−x}Mn{sub x}O{sub 3} (0.0 ≤ x ≤0.20) is prepared by sol–gel method. • A maximum solubility of x = 0.15 is confirmed by X-ray diffraction, Raman and infrared techniques. • Samples with x > 0.05 exhibit weak ferromagnetic properties; for x ≤ 0.05 antiferromagnetic behaviors is obtained. • Correlation between magnetic behaviors and structural and microstructural parameters is discussed. - Abstract: Mixed oxide Sm{sub 2−x}Mn{sub x}O{sub 3} (SMO), x = 0.0, 0.05, 0.10, 0.15 and 0.20 were synthesized by a sol–gel process. A single phase solid solution is formed up to x = 0.15 which confirmed by using X-ray diffraction, Raman spectroscopy and infrared techniques. Crystal structure and microstructure analyses were performed by Rietveld refinement. Preferential cationic distribution, over the two crystallographic sites 8b and 24d of space group Ia3{sup ¯}, is found for doped samples but with different extent. The r.m.s. microstrain 〈ε{sub L}{sup 2}〉{sup 1/2} depends on composition x in a systematic way emphasizing the preferential distribution. Magnetization measurements show that samples with x ≤ 0.05 have antiferromagnetic behavior, while samples with x > 0.05 exhibit a weak ferromagnetic behavior with magnetic phase transformation at 15 and 16 K for x = 0.1 and x = 0.15, respectively.

36 MATERIALS SCIENCE↗

Improved fabrication techniques for infrared bolometers

Ion implantation and sputter metallization are used to produce ohmic electrical contacts to Ge:Ga chips. The method is shown to give a high yield of small monolithic bolometers with very little low-frequency noise. It is noted that when one of the chips is used as the thermometric element of a composite bolometer it must be bonded to a dielectric substrate. The thermal resistance of the conventional epoxy bond is measured and found to be undesirably large. A procedure for soldering the chip to a metallized portion of the substrate in such a way as to reduce this resistance is outlined. An evaluation is made of the contribution of the metal film absorber to the heat capacity of a composite bolometer. It is found that the heat capacity of a NiCr absorber at 1.3 K can dominate the bolometer performance. A Bi absorber possesses significantly lower heat capacity. A low-temperature blackbody calibrator is built to measure the optical responsivity of bolometers. A composite bolometer system with a throughput of approximately 0.1 sr sq cm is constructed using the new techniques. The noise in this bolometer is white above 2.5 Hz and is slightly below the value predicted by thermodynamic equilibrium theory.

Lange, A. E.↗

The continuous measurement of hydrogen chloride in the ambient atmosphere using the dual isotope infrared absorption technique

The results of a program to develop a prototype gas filter correlation NDIR analyzer capable of providing the required HCl measurement capability, while maintaining an adequate rejection of any other gases anticipated in the atmosphere are presented. Examples of the performance of the prototype analyzer are presented which show an rms noise equivalent concentration of 0.06 ppm of HCl was achieved while maintaining an electronically determined 10% to 90% time response to gas samples of about 2 seconds. No measureable response was observed to CO2, CO, and H2O while maintaining an adequate rejection of the hydrocarbons, for example CH4 and n-hexane. The experiments were performed which demonstrate that the span stability of the HCl gas filter correlation analyzer is unaffected by the presence of water vapor and which support the belief that the incorporation of a relatively open-volume, multiple path sample cell into the instrument would enable ground station as well as airborne measurements of trace quantities of HCl in the ambient atmosphere to be performed.

Williams, K. G.↗

Visual Alinement Technique for Infrared LIDAR

Visible He/Ne laser beam substituted for invisible CO2 beam during alinement. System accomplished visually by using low-power He/Ne laser previously adjusted to visible beam parallel to invisible infrared CO2 laser beam. Method used to aline adjacent telescopes in other optical systems.

Menzies, R. T.↗

Atmospheric studies and applications with infrared heterodyne detection techniques

With the advent of stable, cw infrared lasers with moderate output power capabilities in the mid 1960's came the idea of using heterodyne detection, a mature radio frequency technique, in the infrared. This technique was first applied in radar and communications applications; however, it became apparent that infrared lasers and heterodyne detection techniques would be useful in a number of atmospheric measurement applications. The level to which these techniques are being put to use in field measurements is shown using two developed flight instruments as examples.

Menzies, R. T.↗

Prepreg cure monitoring using diffuse reflectance-FTIR

An in situ diffuse reflectance-Fourier transform infrared technique was developed to determine infrared spectra of graphite fiber prepregs as they were being cured. A bismaleimide, an epoxy, and addition polyimide matrix resin prepregs were studied. An experimental polyimide adhesive was also examined. Samples were positioned on a small heater at the focal point of diffuse reflectance optics and programmed at 15 F/min while FTIR spectra were being scanned, averaged, and stored. An analysis of the resulting spectra provided basic insights into changes in matrix resin molecular structure which accompanied reactions such as imidization and crosslinking. An endo-exothermal isomerization involving reactive end-caps was confirmed for the addition polyimide prepregs. The results of this study contribute to a fundamental understanding of the processing of composites and adhesives. Such understanding will promote the development of more efficient cure cycles.

Young, P. R.↗

Feasibility Study of Radiometry for Airborne Detection of Aviation Hazards

Radiometric sensors for aviation hazards have the potential for widespread and inexpensive deployment on aircraft. This report contains discussions of three aviation hazards - icing, turbulence, and volcanic ash - as well as candidate radiometric detection techniques for each hazard. Dual-polarization microwave radiometry is the only viable radiometric technique for detection of icing conditions, but more research will be required to assess its usefulness to the aviation community. Passive infrared techniques are being developed for detection of turbulence and volcanic ash by researchers in this country and also in Australia. Further investigation of the infrared airborne radiometric hazard detection approaches will also be required in order to develop reliable detection/discrimination techniques. This report includes a description of a commercial hyperspectral imager for investigating the infrared detection techniques for turbulence and volcanic ash.

Gimmestad, Gary G.↗

Millimeter and Submillimeter Spectroscopy of Molecules of Atmospheric Importance

In our proposal we laid out work in three areas of relevance to atmospheric science: millimeter and submillimeter spectroscopy, variable temperature pressure broadening, and band and intensity measurements in the FIR. Below we will briefly discuss our progress during the second year of this project. In our millimeter and submillimeter (mm/submm) spectroscopic work, one of our goals has been to work towards the unification of the rotational (primarily obtained by mm/submm techniques) and rotational-vibrational (primarily obtained by infrared techniques) data sets in the context of theoretically well founded models which take advantage of the strengths of the data from each experimental technique. From the point of view of the development of the optimal data base for atmospheric observations, this is clearly a desirable goal. During the first year of this project we did an analysis of a weighted, mixed infrared and mm/submm data set of the n = 0, 1, and 2 torsional states of the ground vibrational state of HOOH. The purpose of this work is to provide a unified understanding of the spectrum, which is applicable in both the rotational and rotational - vibrational regimes. We have succeed in doing this in the context of a single weighted fit which accounts for both data sets to their respective experimental uncertainty (-0.1 and 10 MHz, respectively). Additionally, we have now done a similar analysis on the n = 0 torsional state of v(sub 3) and begun a similar analysis on v(sub 6). For several years we have been working on the mm/submm rotational spectra of the many excited vibrational states of HNO3, again with particular emphasis on the relationships between the mm/submm and infrared spectra. During the first year of this project we were able to use mm/submm spectroscopy to fully resolve the torsional splittings in 2 v(sub 9) and v(sub 5), establish a theoretically well founded quantitative relation between them, and show that both have their physical origin in the torsional motion of the v(sub 9) mode.This result has now been incorporated in a recent reanalysis of the infrared spectrum and has resulted in improved fits - eliminating what was in retrospect a systematic error associated with this previously unknown effect.

DeLucia, Frank C.↗

Ground evaluation of seeding an in-flight wingtip vortex using infrared imaging flow visualization technique

An experimental simulation of an in-flight wingtip vortical flow visualization technique uses infrared imaging to observe strong and concentrated vortices. This experiment is phase 1 of a two-phase infrared evaluation program. The system includes a vortex generator (model 320 Vortec Vortex Tube) which generates the required vortex. The mouth of the unit is mounted close to the free end of a half-inch diameter, sixteen and a half foot long stainless steel tubing (sized after tubing currently installed in the wings of an experimental Beechcraft Sundowner 180 aircraft). Dichloro difluoromethane (Freon-12) is entrained into the generated vortex. A breakdown of the vortices is indicated by the rapid diffusion and the resulting pattern is tracked using the infrared imager and video systems. Flow rates (volume and mass) are estimated at the laboratory and proposed flight conditions. The nominal flight altitude is expected to be 2500 feet.

Akinyanju, Ted↗

Passive optical and infrared meteorology

Applications of passive visible and infrared techniques to the study of meteorological parameters are presented. For the remote sensing of temperature and humidity profiles, infrared sounder improvements have proceeded with the narrow band-pass channels approach, and the partially scanned interferogram approach. Current and planned infrared and microwave sea-surface temperature sounders have an expected accuracy of approximately 2 K, and this can be improved by using three super window channels from the 3.7 micron window region, with narrow band passes away from principal water vapor absorption lines. Cloud data remote sensing is currently performed from satellites, and these visible and infrared images have been used to track weather patterns. In addition, a passive infrared correlation-spectroscopy technique has been proposed for wind measurements. Finally, these techniques have also been applied to monitor such parameters as the Solar Constant, aerosols, and minor gas constituents.

Chahine, M. T.↗

New techniques for far-infrared filters.

The techniques considered make it possible to construct high performance low-pass wide-band, and medium-band filters at wavelengths in the range from 25 to 300 micrometers. Short wavelength rejection without appreciable loss at long wavelengths is achieved by means of small particle scattering. Spectral definition in the far infrared is obtained by cooling one or more crystalline materials to liquid-He or liquid-nitrogen temperatures. The problem of reflection losses at the various surfaces is solved by a new antireflection coating technique.

Armstrong, K. R.↗

CO2 photodissociation and vibrational excitation in the planetary atmospheres

The principal subjects of investigation were the determination of the CO2 photodissociation quantum yields at the wavelengths from 1200 A to 1500 A, and the efficiency of electronic-to-vibrational energy transfer in the systems 0(1D) + CO, N2, CO2 yields 0(3P) + CO N2, CO2 vibrational energies. Measurements on the photodissociation quantum yield of CO2 in the 1200-1500 A region show that it is wavelength dependent, and for the six atomic line sources used, the quantum yield varied from 0.2 to 0.8. The data appear to fit the interpretation of stable CO2 bound states mixed with repulsive or predissociating states, since the low quantum yields coincide with the maximum structure in the CO2 absorption spectrum. The first reliable measurements were made on the efficiency of electronic-to-vibrational energy transfer in the systems 0(1D)-CO and 0(1D)-N2, using a uv resonance fluorescence technique. The 0(1D)-CO2 interaction was investigated by infrared techniques.

Slanger, T. G.↗

A Screening Method Using Pulsed-Power Combined with Infrared Imaging to Detect Pattern Defects in Bulk Metal Foil or Thin Film Resistors

Bulk metal foil and thin film resistors occasionally contain localized defects within the etched resistor pattern. Common defects of this type include in-line constrictions referred to as notches, unremoved resistor material bridges between adjacent pattern lines, and embedded non-conductive particles in the resistor material. Such defects are prone to fracture due to thermomechanical fatigue during powered operation, especially power cycling, resulting in positive resistance change and open circuit failure modes. Common screening methods of optical microscopy, short time overload power tests (e.g., 6.25x rated power for 5 seconds) and burn-in (e.g., 1.5x rated power for 100 hours) are useful, but they are not always effective at removing devices with such defects. An improved method has been developed to screen for localized resistor pattern defects. The method involves the application of brief, high power electrical pulses at a low duty cycle while inspecting the resistor with a high resolution, high speed infrared camera. The following test conditions were found to be suitable for this purpose: 6.25x rated power, 1 to 5 pulses, 50 ms pulse width and 10% duty cycle. During the power pulsing, localized constrictions in the resistor pattern are identifiable as hot spots via the infrared camera. Reject criteria can be established based on observations of hot spots. To assess its effectiveness, a total of two hundred eighty (280) surface mount foil resistors (40 each from 7 different lots) were screened using this infrared technique. The screening identified twenty-nine (29) resistors with significant hot spots in the resistor pattern. All 280 resistors were then subjected to an industry standard 10,000 hour life test at 1x rated power at 70°C with power cycled for 90 minutes on and 30 minutes off. During life testing, three resistors exhibited positive resistance change failure mode. All three failures were due to thermomechanical fatigue failure of localized bridge defects at the locations identified via infrared screening. The results of this evaluation illustrate the benefits of the pulsed-power infrared detection screening technique to identify reliability suspect foil or thin film resistors that may escape common screening methods.

screening↗

A Screening Method Using Pulsed-Power Combined with Infrared Imaging to Detect Pattern Defects in Bulk Metal Foil or Thin Film Resistors

Bulk metal foil and thin film resistors occasionally contain localized defects within the etched resistor pattern. Common defects of this type include in-line constrictions referred to as notches, unremoved resistor material bridges between adjacent pattern lines, and embedded non-conductive particles in the resistor material. Such defects are prone to fracture due to thermomechanical fatigue during powered operation, especially power cycling, resulting in positive resistance change and open circuit failure modes. Common screening methods of optical microscopy, short time overload power tests (e.g., 6.25x rated power for 5 seconds) and burn-in (e.g., 1.5x rated power for 100 hours) are useful, but they are not always effective at removing devices with such defects. An improved method has been developed to screen for localized resistor pattern defects. The method involves the application of brief, high power electrical pulses at a low duty cycle while inspecting the resistor with a high resolution, high speed infrared camera. The following test conditions were found to be suitable for this purpose: 6.25x rated power, 1 to 5 pulses, 50 ms pulse width and 10% duty cycle. During the power pulsing, localized constrictions in the resistor pattern are identifiable as hot spots via the infrared camera. Reject criteria can be established based on observations of hot spots. To assess its effectiveness, a total of two hundred eighty (280) surface mount foil resistors (40 each from 7 different lots) were screened using this infrared technique. The screening identified twenty-nine (29) resistors with significant hot spots in the resistor pattern. All 280 resistors were then subjected to an industry standard 10,000 hour life test at 1x rated power at 70°C with power cycled for 90 minutes on and 30 minutes off. During life testing, three resistors exhibited positive resistance change failure mode. All three failures were due to thermomechanical fatigue failure of localized bridge defects at the locations identified via infrared screening. The results of this evaluation illustrate the benefits of the pulsed-power infrared detection screening technique to identify reliability suspect foil or thin film resistors that may escape common screening methods.

screening↗