Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS AND LOAD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Buckling analysis of fully anisotropic plates containing cutouts and elastically restrained edges

An analysis is developed which combines the Ritz and collocation methods for the stability solution of an anisotropic plate with a cutout and elastically restrained edges. Results are presented which agree closely with experiment for isotropic and orthotropic materials. Results are also given for restrained anisotropic plates with circular holes loaded in compression and shear. Difference is noted in the critical buckling loads between displacement and stress loaded panels as hole size is increased. Clamping is also seen to affect the trends in buckling associated with hole size.

Jones, Kevin M.↗
NASA NTRS2014

Optimal Topology of Aircraft Rib and Spar Structures under Aeroelastic Loads

Several topology optimization problems are conducted within the ribs and spars of a wing box. It is desired to locate the best position of lightening holes, truss/cross-bracing, etc. A variety of aeroelastic metrics are isolated for each of these problems: elastic wing compliance under trim loads and taxi loads, stress distribution, and crushing loads. Aileron effectiveness under a constant roll rate is considered, as are dynamic metrics: natural vibration frequency and flutter. This approach helps uncover the relationship between topology and aeroelasticity in subsonic transport wings, and can therefore aid in understanding the complex aircraft design process which must eventually consider all these metrics and load cases simultaneously.

Stanford, Bret K.↗
NASA NTRS1997

Stressed Oxidation of C/SiC Composites

Constant load, stressed oxidation testing was performed on T-300 C/SiC composites with a SiC seal coat. Test conditions included temperatures ranging from 350 C to 1500 C at stresses of 69 MPa and 172 MPa (10 and 25 ksi). The coupon subjected to stressed oxidation at 550 C/69 MPa for 25 hours had a room temperature residual strength one-half that of the as-received coupons. The coupon tested at the higher stress and all coupons tested at higher temperatures failed in less than 25 hr. Microstructural analysis of the fracture surfaces, using SEM (scanning electron microscopy), revealed the formation of reduced cross-sectional fibers with pointed tips. Analysis of composite cross-sections show pathways for oxygen ingress. The discussion will focus on fiber/matrix interphase oxidation and debonding as well as the formation and implications of the fiber tip morphology.

Halbig, Michael C.↗
NASA NTRS1993

Ratchetting behavior in viscoplasticity - A technical note

Viscoplastic models that use the Armstrong and Frederick (1966) kinematic hardening relationship are known to generally overpredict the observed accumulation of ratchet strains. The reason for this behavior is a consequence of the mathematics used to describe Hooke's law and the evolution equations for plastic strain and back stress. Conditions for ratchetting exist whenever there is a cycle-averaged mean stress present over a cyclic loading path. Two types of controlled loading paths are often studied: cyclic relaxation is the ratchet mechanism associated with displacement (strain) control, while cyclic creep is the ratchet mechanism associated with load (stress) control. Overcoming the possible adverse trends in predicted ratchetting behavior is a difficult task, and how one ought to go about doing this is not yet completely clear. We therefore choose to discuss the mathematical cause of ratchetting and how it has been dealt with to date, but make no attempt to correct this flaw.

Freed, Alan D.↗
NASA NTRS1980

Use of two-dimensional transmission photoelastic models to study stresses in double-lap bolted joints: Load transfer and stresses in the inner lap

The determination of the stress distribution in the inner lap of double-lap, double-bolt joints using photoelastic models of the joint is discussed. The principal idea is to fabricate the inner lap of a photoelastic material and to use a photoelastically sensitive material for the two outer laps. With this setup, polarized light transmitted through the stressed model responds principally to the stressed inner lap. The model geometry, the procedures for making and testing the model, and test results are described.

Hyer, M. W.↗
NASA NTRS1984

Fatigue Testing of Heat-Exchanger Tubes

Acclerated fatigue-life testing of heat-exchanger tubes simplified by technique that substitutes mechanical side load for thermally-generated axisymmetric stress. Load amplitudes adjusted to produce strains equivalent to those produced by anticipated thermal stress.

Ackerman, P.↗
NASA NTRS1971

Evaluation of nondestructive tensile testing

The results of a series of experiments performed in the evaluation of nondestructive tensile testing of chip and wire bonds are presented. Semiconductor devices were subjected to time-temperature excursions, static-load life testing and multiple pre-stressing loads to determine the feasibility of a nondestructive tensile testing approach. The report emphasizes the importance of the breaking angle in determining the ultimate tensile strength of a wire bond, a factor not generally recognized nor implemented in such determinations.

Bowe, J. J.↗
NASA NTRS2006

Maximum von Mises Stress in the Loading Environment of Mass Acceleration Curve

Method for calculating stress due to acceleration loading: 1) Part has been designed by FEA and hand calculation in one critical loading direction judged by the analyst; 2) Maximum stress can be due to loading in another direction; 3) Analysis procedure to be presented determines: a) The maximum Mises stress at any point; and b) The direction of maximum loading associated with the "stress". Concept of Mass Acceleration Curves (MAC): 1) Developed by JPL to perform preliminary structural sizing (i.e. Mariners, Voyager, Galileo, Pathfinder, MER,...MSL); 2) Acceleration of physical masses are bounded by a curve; 3) G-levels of vibro-acoustic and transient environments; 4) Convergent process before the couple loads cycle; and 5) Semi-empirical method to effectively bound the loads, not a simulation of the actual response.

von Mises stress↗
NASA NTRS2002

Influence of Crack-Tip Configurations on the Fracture Response of 0.04-Inch Thick 2024-T3 Aluminum Alloy Sheet

A series of fracture tests were conducted on Middle-crack tension M(T) and compact tension C(T) specimens to determine the effects of specimen type, specimen width, notch tip sharpness and buckling on the fracture behavior of cracked thin sheet (0.04 inch thick) 2024-T3 aluminum alloy material. A series of M(T) specimens were tested with three notch tip configurations: (1) a fatigue pre-cracked notch, (2) a 0.010-inch-diameter wire electrical discharge machined (EDM) notch, and (3) a EDM notch sharpened with a razor blade. The test procedures are discussed and the experimental results for failure stress, load vs. crack extension and the material stress-strain response are reported.

Johnston, William M.↗
NASA NTRSDate not supplied

Structural Analysis of Load-Bearing Components in Mars Science Helicopter

The successful demonstration of powered flight on Mars by Ingenuity has led to the development of next generation Martian rotorcraft. As technology advances from a technology demonstrator to possible expanded planetary science investigations, the potential to fly a high payload carrying rotorcraft relies on the capability to analyze and validate the structural integrity of the vehicle in addition to the rotor aerodynamic performance. The Mars Science Helicopter (MSH), a next generation hexacopter concept, is one example of a proposed vehicle that would perform science independently of a land-based vehicle. To ensure the feasibility and viability of MSH mission performance, it is critical to mature the structural design for these vehicle concepts to bridge the gap between the best practices of the spacecraft and aircraft communities. MSH was analyzed under operational and 26G quasi-static launch loads with different rotor arm and fuselage designs. Structural analysis results showed that rotor arms could be stiffened for significantly improved structural performance with minimal mass penalty, while the rotorcraft frame exhibited a more complex relationship between mass and launch load stresses due to the mass-dependent launch loads.

Load-Bearing↗
NASA NTRS2025

Structural Analysis of Load-Bearing Components in Mars Science Helicopter

The successful demonstration of powered flight on Mars by Ingenuity has led to the development of next generation Martian rotorcraft. As technology advances from a technology demonstrator to possible expanded planetary science investigations, the potential to fly a high payload carrying rotorcraft relies on the capability to analyze and validate the structural integrity of the vehicle in addition to the rotor aerodynamic performance. The Mars Science Helicopter (MSH), a next generation hexacopter concept, is an example of a proposed vehicle that would perform science investigations independent of a land-based vehicle. To ensure the feasibility and viability of MSH mission performance, it is critical to mature the structural design of vehicle concepts to bridge the gap between the best practices of the spacecraft and aircraft communities. MSH was analyzed under operational and 26G quasi-static launch loads with different rotor arm and frame designs. Structural analysis results showed that rotor arms could be stiffened for significantly improved structural performance with minimal mass penalty, while the rotorcraft frame exhibited a more complex relationship between mass and launch load stresses due to the mass-dependent launch loads.

Vehicle↗
NASA NTRS1978

The viscoelastic stiffness model of seismicity

A viscoelastic stiffness model of seismicity is developed by introducing a viscoelastic element into the stiffness model for fault dynamics. The introduction of this element permits modeling of transient anelastic deformations in response to stress loading and relaxation and provides a mechanism for partial stress recovery following an earthquake. As a consequence, several phenomena not present in elastic stiffness theory emerge. These include postseismic creep, foreshocks, and aftershocks. Numerical simulations of fault motion also reveal episodes of stable sliding, tertiary creep preceeding earthquakes, and long-term aseismic creep.

Cohen, S. C.↗
NASA NTRS2004

Eccentric loading of microtensile specimens

Ceramic materials have a lower density than most metals and are capable of performing at extremely high temperatures. The utility of these materials is obvious; however, the fracture strength of brittle materials is not easily predicted and often varies greatly. Characteristically, brittle materials lack ductility and do not yield as other materials. Ceramics materials are naturally populated with microscopic cracks due to fabrication techniques. Upon application of a load, stress concentration occurs at the root of these cracks and fracture will eventually occur at some not easily predicted strength. In order to use ceramics in any application some design methodology must exist from which a component can be placed into service. This design methodology is CARES/LIFE (Ceramics Analysis and Reliability Evaluation of Structures) which has been developed and refined at NASA over the last several decades. The CARES/LIFE computer program predicts the probability of failure of a ceramic component over its service life. CARES combines finite element results from a commercial FE (finite element) package such as ANSYS and experimental results to compute the abovementioned probability of failure. Over the course of several tests CARES has had great success in predicting the life of various ceramic components and has been used throughout industry. The latest challenge is to verify that CARES is valid for MEMS (Micro-Electro Mechanical Systems). To investigate a series of microtensile specimens were fractured in the laboratory. From this data, material parameters were determined and used to predict a distribution of strength for other specimens that exhibit a known stress concentration. If the prediction matches the experimental results then these parameters can be applied to a desired component outside of the laboratory. During testing nearly half of the tensile Specimens fractured at a location that was not expected and hence not captured in the FE model. It has been my duty to investigate the nature of this phenomenon in hopes of finding a better correlation between theory and empirical results. To investigate I built complete FE models of all of the tensile specimens using ANSYS. It is suspected that some misalignment naturally occurs during testing and thus additional bending stresses are present in the specimens. I modeled this eccentric loading and ran several FE trials using ANSYS/PDS (a probabilistic design system in ANSYS). My objective this summer has been familiarize myself with the CARES/LIFE program in hopes of using it in conjunction with ANSYS to help verify that CARES is applicable to MEMS-scale (greater that 1 micron, less than 1 millimeter) components.

Trapp, Mark A.↗
NASA NTRS1997

Wing Weight Optimization Under Aeroelastic Loads Subject to Stress Constraints

A minimum weight optimization of the wing under aeroelastic loads subject to stress constraints is carried out. The loads for the optimization are based on aeroelastic trim. The design variables are the thickness of the wing skins and planform variables. The composite plate structural model incorporates first-order shear deformation theory, the wing deflections are expressed using Chebyshev polynomials and a Rayleigh-Ritz procedure is adopted for the structural formulation. The aerodynamic pressures provided by the aerodynamic code at a discrete number of grid points is represented as a bilinear distribution on the composite plate code to solve for the deflections and stresses in the wing. The lifting-surface aerodynamic code FAST is presently being used to generate the pressure distribution over the wing. The envisioned ENSAERO/Plate is an aeroelastic analysis code which combines ENSAERO version 3.0 (for analysis of wing-body configurations) with the composite plate code.

Kapania, Rakesh K.↗
NASA NTRS1987

On dynamic loads in parallel shaft transmissions. 1: Modelling and analysis

A model of a simple parallel-shaft, spur-gear transmission is presented. The model is developed to simulate dynamic loads in power transmissions. Factors affecting these loads are identified. Included are shaft stiffness, local compliance due to contact stress, load sharing, and friction. Governing differential equations are developed and a solution procedure is outlined. A parameter study of the solutions is presented in NASA TM-100181 (AVSCOM TM-87-C-3).

Lin, Edward Hsiang-Hsi↗