Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solar Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Study to determine and improve design for lithium-doped solar cells

Solar cell experiments show that a single lithium density parameter, the lithium density gradient, calculated from nondestructive capacitance measurements, provides the basis for accurate predictions of lithium cell behavior in a 1-MeV electron environment for fluences ranging between 3 X 10 to the 13th power e/sq cm and 3 X 10 to the 15th power/e sq cm. The oxygen-rich (quartz crucible) lithium cell with phosphorous starting dopant and lithium gradient between approximately 5 X 10 to the 18th power and 1.5 x 10 to the 19th power/cm to the 4th power was found superior in performance to the commercial 10 ohm-cm n/p control cells. Post-recovery stability of oxygen-rich cells was satisfactory. An average post-recovery current drop of approximately 1 mA was observed for 70 crucible cells after 1 year-equivalent storage time at 80 C. In contrast the oxygen-poor (float zone and Lopex) lithium cells displayed spotty initial performance and stability problems at room temperature.

Brucker, G.↗

Breakdown phenomena in reverse biased silicon solar cells.

Solar cell reverse current-voltage characteristics have been found to vary widely and to be generally unstable. At reverse voltages greater than approximately 20 V and at cell power dissipations of more than 4 W, the probability of permanent breakdown, resulting in cell short-circuit failure, was found to increase with increasing voltage and exposure time. Shorted cells showed evidence of cell contact material and silicon melting in very localized areas with lava-like flow patterns and channels bridging the p and n contacts.

Rauschenbach, H. S.↗

Uniform solar cells

Solar cells used in radiation sensors can be efficiently matched by individual trimming. Strip of aluminized Mylar is used to adjust cell output to within required tolerances. Method is faster than individual selection of matched cells.

Source record↗

Low cost processes for fabricating silicon solar cells

Solar cell fabrication processes, in particular junction formation and metallization, are evaluated in terms of cell efficiencies, process yields, module packing factors, and energy cost effectiveness. It is shown that for junction formation, the diffusion processes provide a relatively low-cost approach. The costs per unit cell area can be further reduced by increased wafer area and mechanized wafer handling. The costs for a large number of metallization processes, excluding the costs of the metal, are roughly comparable. However, their varying influence on cell performance leads to a significant spread in the allowable process costs.

Goldman, H.↗

Diagnostic study of BSF silicon solar cells

Solar cells equipped with back surface fields (BSF) were fabricated by means of an aluminum alloy, boron diffusion, and boron ion implantation. The importance of initial thickness, resistivity, orientation, and the crystal growth method were examined. Aluminum in paste form was screen printed on the cell, followed by alloy formation at 800 C for a minute. Application of the BSFs resulted in open circuit voltage improvements dependent on the substrate resistivity, ranging from 10 mV at 0.3 ohm-cm to 50 mV at 15 ohm-cm. The gains in performance were attributed to a longer penetration depth, a heightened concentration profile at the interface, and higher concentrations in the p+ layer.

Yoo, H.↗

Advances in high output voltage silicon solar cells

Solar cells have been fabricated from 0.1 ohm-cm, p-type silicon by means of a two-step diffusion process of emitter formation in order to delineate the factors limiting V(oc) in conventionally structured cells with the goal of achieving 700 mV. The cells are 200 microns thick and 2 x 2 cm in area with a planar front surface that has an anti-reflection coating of tantalum oxide, as well as Cr-Au-Ag contact metallization on both sides of the cell. The Cr-Au-Ag is applied over an aluminum diffused layer on the back, while it is applied through small holes in the anti-reflection coating on the front. Results show that the best of these cells exhibits an open-circuit voltage of 654 mV under AMO illumination.

Arndt, R. A.↗

Development of technique for air coating and nickel and copper metalization of solar cells

Solar cells were made with a variety of base metal screen printing inks applied over silicon nitride AR coating and copper electroplated. Fritted and fritless nickel and fritless tin base printing inks were evaluated. Conversion efficiencies as high as 9% were observed with fritted nickel ink contacts, however, curve shapes were generally poor, reflecting high series resistance. Problems encountered in addition to high series reistance included loss of adhesion of the nickel contacts during plating and poor adhesion, oxidation and inferior curve shapes with the tin base contacts.

Source record↗

Radiation resistance of Ge, Ge0.93Si0.07, GaAs and Al0.08Ga0.92 as solar cells

Solar cells made of Ge, Ge(0.93)Si(0.07) alloys, GaAs and Al(0.08)Ga(0.92)As were irradiated in two experiments with 1-meV electrons at fluences as great as 1 x 10(exp 16) cm(exp-2). Several general trends have emerged. Low-band-gap Ge and Ge(0.93)Si(0.07) cells show substantial resistance to radiation-induced damage. The two experiments showed that degradation is less for Al(0.08)Ga(0.92)As cells than for similarly irradiated GaAs cells. Compared to homojunctions, cells with graded-band-gap emitters did not show the additional resistance to damage in the second experiment that had been seen in the first. The thickness of the emitter is a key parameter to limit the degradation in GaAs devices.

Timmons, M. L.↗

Scalable fabrication and coating methods for perovskite solar cells and solar modules

Since the report in 2012 of a solid-state perovskite solar cell (PSC) with a power-conversion efficiency (PCE) of 9.7% and a stability of 500 h, intensive efforts have been made to increase the certified PCE, reaching 25.2% in 2019. The PCE of PSCs now exceeds that of conventional thin-film solar-cell technologies, and the rate at which this increase has been achieved is unprecedented in the history of photovoltaics. Moreover, the development of moisture-stable and heat-stable materials has increased the stability of PSCs. Small-area devices (<1 cm2) are typically fabricated using a spin-coating method; however, this approach may not be suitable for the preparation of the large-area (>100 cm2) substrates required for commercialization. Thus, materials and methods need to be developed for coating large-area PSCs. In this Review, we discuss solution-based and vapour-phase coating methods for the fabrication of large-area perovskite films, examine the progress in performance and the parameters affecting the properties of large-area coatings, and provide an overview of the methodologies for achieving high-efficiency perovskite solar modules.

14 SOLAR ENERGY↗

Recent HVPE Grown Solar Cells at NREL: Preprint

In this work we present solar cells grown via hydride vapor phase epitaxy (HVPE) in NREL's dynamic HVPE reactor. We show single junction GaAs and GaInP solar cells with efficiencies as high as 25.5% and 15.2% respectively, and dual junction solar cells with an efficiency of 24.9%.

GaAs↗

Four-cell solar tracker

Forty cm Sun tracker, consisting of optical telescope and four solar cells, stays pointed at Sun throughout day for maximum energy collection. Each solar cell generates voltage proportional to part of solar image it receives; voltages drive servomotors that keep image centered. Mirrored portion of cylinder extends acquisition angle of device by reflecting Sun image back onto solar cells.

Berdahl, C. M.↗

Emitter/absorber interface of CdTe solar cells

The performance of CdTe solar cells can be very sensitive to the emitter/absorber interface, especially for high-efficiency cells with high bulk lifetime. Performance losses from acceptor-type interface defects can be significant when interface defect states are located near mid-gap energies. Numerical simulations show that the emitter/absorber band alignment, the emitter doping and thickness, and the defect properties of the interface (i.e., defect density, defect type, and defect energy) can all play significant roles in the interface recombination. In particular, a type I heterojunction with small conduction-band offset (0.1 eV ≤ ΔE{sub C} ≤ 0.3 eV) can help maintain good cell efficiency in spite of high interface defect density, much like with Cu(In,Ga)Se{sub 2} (CIGS) cells. The basic principle is that positive ΔE{sub C}, often referred to as a “spike,” creates an absorber inversion and hence a large hole barrier adjacent to the interface. As a result, the electron-hole recombination is suppressed due to an insufficient hole supply at the interface. A large spike (ΔE{sub C} ≥ 0.4 eV), however, can impede electron transport and lead to a reduction of photocurrent and fill-factor. In contrast to the spike, a “cliff” (ΔE{sub C} < 0 eV) allows high hole concentration in the vicinity of the interface, which will assist interface recombination and result in a reduced open-circuit voltage. Another way to mitigate performance losses due to interface defects is to use a thin and highly doped emitter, which can invert the absorber and form a large hole barrier at the interface. CdS is the most common emitter material used in CdTe solar cells, but the CdS/CdTe interface is in the cliff category and is not favorable from the band-offset perspective. The ΔE{sub C} of other n-type emitter choices, such as (Mg,Zn)O, Cd(S,O), or (Cd,Mg)Te, can be tuned by varying the elemental ratio for an optimal positive value of ΔE{sub C}. These materials are predicted to yield higher voltages and would therefore be better candidates for the CdTe-cell emitter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗