Search NASA⌕ Search

SEARCH · Search NASA

Results for “Spalling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Spall fracture in additive manufactured Ti-6Al-4V

Here, we present a study on the spall strength of additive manufactured (AM) Ti-6Al-4V. Samples were obtained from two pieces of selective laser melted (SLM, a powder bed fusion technique) Ti-6Al-4V such that the response to dynamic tensile loading could be investigated as a function of the orientation between the build layers and the loading direction. A sample of wrought bar-stock Ti-6Al-4V was also tested to act as a baseline representing the traditionally manufactured material response. A single-stage light gas-gun was used to launch a thin flyer plate into the samples, generating a region of intense tensile stress on a plane normal to the impact direction. The rear free surface velocity time history of each sample was recorded with laser-based velocimetry to allow the spall strength to be calculated. The samples were also soft recovered to enable post-mortem characterization of the spall damage evolution. Results showed that when the tensile load was applied normal to the interfaces between the build layers caused by the SLM fabrication process the spall strength was drastically reduced, dropping to 60% of that of the wrought material. However, when loaded parallel to the AM build layer interfaces the spall strength was found to remain at 95% of the wrought control, suggesting that when loading normal to the AM layer interfaces, void nucleation is facilitated more readily due to weaknesses along these boundaries. Quasi-static testing of the same sample orientations revealed a much lower degree of anisotropy, demonstrating the importance of rate-dependent studies for damage evolution in AM materials.

36 MATERIALS SCIENCE↗
DOE OSTI2018

GaAs Solar Cells Grown on Unpolished, Spalled Ge Substrates

We spalled 2-inch Ge wafers using a Ni stressor layer and grew GaAs solar cells by hydride vapor phase epitaxy on the spalled Ge surface without other surface treatments. The controlled spalling procedure leaves behind arrest lines, which are parallel surface striations, perpendicular to the crack front, caused by the crack propagation repeatedly halting and restarting during the fracture. We show that small arrest lines do not significantly affect device performance, but larger lines act as regions for carrier recombination. We demonstrate a 12.8% efficient single-junction device, without anti-reflection coating, grown on a spalled surface containing arrest lines. The quantum efficiency of this device is similar to devices grown on non-spalled GaAs and Ge substrates.

14 SOLAR ENERGY↗
DOE OSTI2019

Spall Strength of Shock-Heated Hafnium and the Equation of State of Its Polymorphic Modifications

We determined the spall strength of hafnium heated by a loading shock wave to thousands of degrees and subjected to transformations into denser polymorphic modifications. To achieve this goal, the following tasks were solved. The pressure profiles at the interface between the sample and soft buffer material in the spall experiments with flat, one-dimensional loading are measured. The equations of state of three polymorphic modifications of hafnium are constructed in the pressure range up to 100 GPa. The thermodynamic states of hafnium were calculated under the conditions of the performed experiments, which, together with the results of measurements of pressure profiles, made it possible to determine the spall strength of hafnium heated in a cycle of shock compression–unloading. The spall strength of hafnium was –4(1) GPa at a temperature of 1680(380) K. The spall experiments were mathematically simulated in the framework of a one-dimensional hydrocode.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

High‐Efficiency Solar Cells Grown on Spalled Germanium for Substrate Reuse without Polishing

Abstract Radical reduction of III–V device costs requires a multifaceted approach attacking both growth and substrate costs. Implementing device removal and substrate reuse provides an opportunity for substrate cost reduction. Controlled spalling allows removal of thin devices from the expensive substrate; however, the fracture‐based process currently generates surfaces with significant morphological changes compared to polished wafers. 49 single junction devices are fabricated across the spalled surface of full 50 mm germanium wafers without chemo‐mechanical polishing before epitaxial growth. Device defects are identified and related to morphological spalling defects—arrest lines, gull wings, and river lines—and their impact on cell performance using physical and functional characterization techniques. River line defects have the most consistent and detrimental effect on cell performance. Devices achieve a single junction efficiency above 23% and open‐circuit voltage of 1.01 V, demonstrating that spalled germanium does not need to be returned to a pristine, polished state to achieve high‐quality device performance.

14 SOLAR ENERGY↗
DOE OSTI2021

Facet Suppression in (100) GaAs Spalling via Use of a Nanoimprint Lithography Release Layer

Controlled spalling is an emerging technique developed for fast, scalable wafer reuse, but for the commonly used (100) GaAs substrate system, the process leaves large facets ranging from 5-10 µm on the wafer surface. Removing them for wafer reuse requires a costly re-polishing step that limits the cost savings that can be achieved with spalling as a wafer reuse technique. In this study, we investigate facet suppression in spalling of (100) GaAs by redirecting the fracture front along features created by buried nanoimprint lithography (NIL)-patterned SiO 2 . We show successful facet suppression using patterns that result in favorable fracture along the SiO 2 /GaAs interface. The results from this work show NIL patterned interlayers are a promising method for faceting suppression in (100) GaAs spalling.

controlled spalling↗
DOE OSTI2022

Effect of Grain Boundary Misorientation on Spall Strength in Ta via Shock-Free Simulations with Relatively Few Atoms

A suite of 37 molecular dynamics simulations is conducted at two system sizes to systematically characterize the role of grain boundary (GB) misorientation on spall strength in pure BCC tantalum (Ta). The systems studied consist of bicrystals with a single [110] symmetric tilt grain boundary. Two loading conditions are compared: (i) homogeneous extension under uniaxial strain simulated in this study and (ii) piston/flyer impact of sample, which induces heterogeneous deformation via shockwave propagation along the length of the sample. The piston/flyer impact is taken from the literature and run on the same set of GB misorientation angles using LAMMPS. The major finding here is that both methods result in similar spall strength predictions, but the homogeneous extension method generally requires two to three orders of magnitude fewer atoms and similar reductions in computational costs. Spall strength results systematically overpredict using this method, by about 10% for the dataset three orders of magnitude smaller than piston/flyer simulations, and 5% for the dataset two orders of magnitude smaller. Lastly, the effect of system size and pre-compression magnitude on spall strength is systematically characterized.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Correlations among void shape distributions, dynamic damage mode, and loading kinetics [Correlations among spall void shape distributions, damage mode and shock loading kinetics]

Here, three-dimensional x-ray tomography (XRT) provides a nondestructive technique to characterize the size, shape, and location of damage in dynamically loaded metals. A shape-fitting method comprising the inertia tensors of individual damage sites was applied to study differences of spall damage development in face-centered-cubic (FCC) and hexagonal-closed-packed (HCP) multicrystals and for a suite of experiments on high-purity copper to examine the influence of loading kinetics on the spall damage process. Applying a volume-weighted average to the best-fit ellipsoidal aspect-ratios allows a quantitative assessment for determining the extent of damage coalescence present in a shocked metal. It was found that incipient transgranular HCP spall damage nucleates in a lenticular shape and is heavily oriented along particular crystallographic slip directions. In polycrystalline materials, shape distributions indicate that a decrease in the tensile loading rate leads to a transition to coalesced damage dominance and that the plastic processes driving void growth are time dependent.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Orientation dependent spall strength of tantalum single crystals

We report that it is generally recognized that single crystals exhibit orientation-dependent elastic and plastic responses. However, it is less known how the dynamic tensile, or spall, strength depends on crystalline orientation, especially for BCC materials. It has been previously shown that the dynamic tensile strength of FCC materials is highly dependent on their plastic response under compression, with a direct correlation between plastic deformation and spall strength. In BCC materials like Ta, where the primary deformation mechanism at high strain rates is a combination of slip and twinning, the quantitative dependence of spall strength on these deformation mechanisms is less understood. To fill this gap in our knowledge, a series of non-equilibrium molecular dynamics simulations are completed for six tantalum single crystal orientations: <001>, <011>, <111>, <013>, <112>, <149>, to explore the role of directional anisotropy on ductile spallation. Our results show that due to the role of non-Schmid and release effects in BCC Ta, the evolution of plasticity follows a complex trajectory through shock compression, release, and tension. Orientations that contain residual twinning deformation have a reduced spall strength proportional to the amount of twinning present. Lastly, twins and their intersections function as regions of increased stress localization within the system due to compatibility requirements and their interactions with dislocations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Subgrain geometrically necessary dislocation density mapping in spalled Ta in three dimensions

Here, in this work, the intragranular distributions of the densities of geometrically necessary dislocations (GNDs) generated in a polycrystalline tantalum (Ta) sample loaded in shock compression to spall are investigated. The sample studied is a highly resolved three-dimensional (3D) map of the orientations, grain boundary morphology, and voids across a 0.276mm 3 (with sample dimensions of 688.5µm x 669µm x 600µm) region of the microstructure about the spall plane obtained by TriBeam tomography. We present a formulation for calculating the crystallographic screw and edge character GND densities at a material point within body centered cubic (BCC) crystals when provided any number of potential slip systems or modes. Combining the 3D characterization, GND formulation, and a sample containing ≈ 6000 grains, we sought statistically relevant correlations between GND density per grain with grain size, grain orientation, void formation, and proximity from the spall plane. We show that GND density per grain increases with decreasing distance from the spall plane. Most grains had heterogeneously distributed GND densities but were free of any detectable voids, at least within the ≈ 1.5µm resolution of the characterization technique. It is found that the GND density for most grains is insensitive to grain size and grain orientation. Only the fraction of grains with the highest GND densities tended to have a [001] parallel to shock-direction orientation. Intragranular 3D maps of GNDs reveals that grains that contain voids have high GND density concentrations in the intragranular region immediately surrounding the void. The local intragranular GND mapping also showed voids that are connected to grain boundaries preferred to grow into the grain with the larger size, regardless of orientation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of spatial distribution of polymer fibers on preventing spalling of UHPC at high temperatures

Polypropylene (PP) fibers are commonly used for the prevention of thermal spalling of ultra-high performance concrete (UHPC). In this work, the effect of fiber distribution on permeability and spalling resistance is investigated and an analytical model for permeability at 150 °C is proposed. This model, considering the parameters like fiber dimensions, dosage, and percolation, is based on Kozeny-Carman equation. It was found that the percolation of the interconnecting fiber network resulted in a significant increase in permeability of UHPC. X-ray tomography data on the three-dimensional spatial distribution of fibers reiterated that fiber aspect ratio and dosage (and fiber number density) were critical in increasing the fiber connectivity (percolation). It was also found that a vapor permeability of larger than 0.6 × 10{sup −16} m{sup 2} at 150 °C could eliminate spalling. Further, based on a semi-empirical approach, aspect ratio between 300 and 600 was recommended for spalling prevention with a fiber dosage of 0.3–0.4 vol%.

36 MATERIALS SCIENCE↗
DOE OSTI2023

GaAs solar cells grown on acoustically spalled GaAs substrates with 27% efficiency

Acoustic spalling presents a potentially low-cost reuse pathway for III–V epitaxial growth substrates via exfoliation of device layers with recovery and reuse of the substrate. However, surface features formed during spalling can reduce the performance of subsequently grown devices. Here, we develop an understanding of how the surface morphology of acoustically spalled substrates affects GaAs solar cell performance and develop strategies to mitigate these impacts. We demonstrate that minor planarization of the surface by wet chemical etching and/or epitaxial growth, or the redesign of the device structure to thicken critical layers, prevents performance degradation. Using these strategies, we demonstrate a 0.25 cm 2 single-junction GaAs device with 26.9% ± 0.2% photovoltaic conversion efficiency under the AM1.5G spectrum grown on an acoustically spalled substrate. These results enable the growth of high-performance III–V devices on non-traditional substrates with the potential for significantly reduced device costs.

14 SOLAR ENERGY↗
DOE OSTI2020

Shock recompaction of spall damage

Spall fracture is a high strain-rate damage phenomenon associated with shock or impulsive loading events. When a material that has been subjected to shock compression is allowed to release, rarefaction waves propagate into the sample and reduce the internal stress to zero. If multiple rarefaction waves intersect, they generate tension which, if sufficient, can nucleate voids in the material. It has been observed in several works investigating spall fracture that although the shock-wave profiles suggested spall occurred, imaging of the recovered sample revealed no voids or cracks. In this study, we aim to determine whether a second shock event could recompact existing spall damage, and if so, what form does the microstructure at the recompaction interface have? Through a series of gas-gun flyer-plate impact experiments, we demonstrate that modest shock stresses of 2 GPa–3 GPa are enough to both fully compact a damaged copper target back to a state of zero porosity and, furthermore, drive recrystallization of the interface such that there is a new bond formed where the free surfaces were brought together.

42 ENGINEERING↗
DOE OSTI2022

Constrained model calibration of grain structure dependent spall dynamics in shock-loaded tantalum

Here, we perform a gas gun experiment by shock loading tantalum samples of varying grain structures to assess the suitability of a numerical model for simulating spall behavior. The observed differences in spall strength, as well spallation and re-compression history, are not captured in uncalibrated hydrodynamic simulations. An optimization is performed on the Johnson spall model to determine the best parameters that fit the observed trends. Linear stability analysis is employed to motivate bounds on those parameters. Herein, optimized simulations agree well with the experimental results, reproducing pullback depth and recompression timescales across the different samples tested. Further, the observed pullback time of the single crystal sample was found to imply, via the stability analysis, a percolation threshold in good agreement with the theoretical value for a body centered cubic lattice. Therefore, the combined linear stability and percolation analysis shows promise and may be applied to other materials with diverse microstructures. Collectively, the findings demonstrate that the model is suitable for reproducing spall-induced free surface behavior across various microstructures, but also points to caution in using model coefficients for uncalibrated microstructures.

58 GEOSCIENCES↗
DOE OSTI2024

High-throughput quantification of quasistatic, dynamic and spall strength of materials across 10 orders of strain rates

Abstract The response of metals and their microstructures under extreme dynamic conditions can be markedly different from that under quasistatic conditions. Traditionally, high strain rates and shock stresses are achieved using cumbersome and expensive methods such as the Kolsky bar or large spall experiments. These methods are low throughput and do not facilitate high-fidelity microstructure–property linkages. In this work, we combine two powerful small-scale testing methods, custom nanoindentation, and laser-driven microflyer (LDMF) shock, to measure the dynamic and spall strength of metals. The nanoindentation system is configured to test samples from quasistatic to dynamic strain-rate regimes. The LDMF shock system can test samples through impact loading, triggering spall failure. The model material used for testing is magnesium alloys, which are lightweight, possess high-specific strengths, and have historically been challenging to design and strengthen due to their mechanical anisotropy. We adopt two distinct microstructures, solutionized (no precipitates) and peak-aged (with precipitates) to demonstrate interesting upticks in strain-rate sensitivity and evolution of dynamic strength. At high shock-loading rates, we unravel an interesting paradigm where the spall strength vs. strain rate of these materials converges, but the failure mechanisms are markedly different. Peak aging, considered to be a standard method to strengthen metallic alloys, causes catastrophic failure, faring much worse than solutionized alloys. Our high-throughput testing framework not only quantifies strength but also teases out unexplored failure mechanisms at extreme strain rates, providing valuable insights for the rapid design and improvement of materials for extreme environments.

Eswarappa Prameela, Suhas (ORCID:0000000334530184)↗
DOE OSTI2016

DRSPALL: Impact of the Modification of the Numerical Spallings Model on Waste Isolation Pilot Plant Performance Assessment.

The numerical code DRSPALL (from direct release spallings) is written to calculate the volume of Waste Isolation Pilot Plant (WIPP) solid waste subject to material failure and transport to the surface as a result of a hypothetical future inadvertent drilling intrusion. An error in the implementation of the DRSPALL finite difference equations was discovered as documented in Software Problem Report (SPR) 13-001. The modifications to DRSPALL to correct the finite difference equations are detailed, and verification and validation testing has been completed for the modified DRSPALL code. The complementary cumulative distribution function (CCDF) of spallings releases obtained using the modified DRSPALL is higher compared to that found in previous WIPP performance assessment (PA) calculations. Compared to previous PAs, there was an increase in the number of vectors that result in a nonzero spallings volume, which generally translates to an increase in spallings releases. The overall mean CCDFs for total releases using the modified DRSPALL are virtually unchanged, thus the modification to DRSPALL did not impact WIPP PA calculation results.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2019

Spall kinetics model description

Under high-rate loading in tension, metals can sustain much larger tensile stresses for sub-microsecond time periods than would be possible under quasi-static conditions. This type of failure, known as spall, is not adequately reproduced by hydrocodes with commonly used failure models. The Spall Kinetics Model treats spall by incorporating a time scale into the process of failure. Under sufficiently strong tensile states of stress, damage accumulates over this time scale, which can be thought of as an incubation time. The time scale depends on the previous loading history of the material, reflecting possible damage by a shock wave. The model acts by modifying the hydrostatic pressure that is predicted by any equation of state and is therefore simple to implement. Examples illustrate the ability of the model to reproduce the spall stress and resulting release waves in plate impact experiments on stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2023

MST-8 Colloquium: The Effect of Microstructure on the Spall Strength and Damage of 1045 Steel [Slides]

Three different microstructures of the same steel alloy were investigated to study the influence of microstructure on spall strength and damage. Microstructure influences spall behavior within the explored dynamic regime. Second phase morphology, interphase interface characteristics, and grain boundary character shown to influence spall behavior. Continued understanding of microstructure’s influence on spall and damage needed for targeted material design.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Spall damage mechanisms in laser powder bed fabricated stainless steel 316L

This paper reports on spall damage mechanisms in laser powder bed fusion (LPBF) fabricated stainless steel 316L (SS316L) subjected to uniaxial, strain plate-impact loading and explores failure evolution with increasing impact velocity and peak pressure. Analysis of velocimetry profiles reveals a heterogeneous failure response with several different failure mechanisms activated during impact and resulting spall. The analysis is supported by optical microscopy and electron backscattered diffraction (EBSD) observation of soft recovered impacted samples, which show evidence of localized nano-twinning, twin growth, severe grain rotation, and grain refinement along the spall plane, in addition to pore nucleation, coalescence, and growth. Furthermore, the observed failure mechanisms, including crack formation and propagation along high angle grain boundaries (HAGBs), are not consistently indicative of ductile fracture typical of wrought stainless steel.

36 MATERIALS SCIENCE↗