Search NASA⌕ Search

SEARCH · Search NASA

Results for “TRT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Effect of ground and ceiling planes on shape of energized wakes

Results are presented from an investigation of the structure of energized wakes in the presence of ground or ceiling planes when powered-lift devices are tested at zero and low wind tunnel velocities. Solutions are presented to indicate how the presence of a nearby ground plane causes the energized wake to constrict less than when in free space. In contrast, another set of solutions indicate that the presence of a ceiling plane enhances wake construction so that the wake width is even smaller than when in free space. Hence, a ground plane tends to reduce the chance for interaction between the wake and the energizing elements, while a nearby ceiling plane tends to increase the likelihood for interference.

TRT-EXPERIMENTAL↗
NASA NTRS1994

Multiblock analysis for Shuttle Orbiter reentry heating from Mach 24 to Mach 12

A multiblock, laminar heating analysis for the shuttle orbiter at three trajectory points ranging from Mach 24.3 to Mach 12.86 on reentry is described. The analysis is performed using the Langley Aerothermodynamic Upwind Relaxation Algorithm with a seven species chemical nonequilibrium model. A finite-catalytic-wall model appropriate for shuttle tiles at a radiative equilibrium wall temperature is applied. Computed heating levels are generally in good agreement with the flight data, although a few rather large discrepancies remain unexplained. The multiblock relaxation strategy partitions the flowfield into manageable blocks requiring a fraction of the computational resources (time and memory) required by a full domain approach. In fact, the computational cost for a solution at even a single trajectory point would be prohibitively expensive at the given resolution without the multiblock approach. Converged blocks are reassembled to enable a fully coupled converged solution over the entire vehicle, starting from a nearly converged initial condition.

LANGLEY AEROTHERMODYNAMIC UPWI↗
NASA NTRS1994

Propulsion requirements for reusable single-stage-to-orbit rocket vehicles

The conceptual design of a single-stage-to-orbit (SSTO) vehicle using a wide variety of evolutionary technologies has recently been completed as a part of NASA's Advanced Manned Launch System (AMLS) study. The employment of new propulsion system technologies is critical to the design of a reasonably sized, operationally efficient SSTO vehicle. This paper presents the propulsion system requirements identified for this near-term AMLS SSTO vehicle. Sensitivities of the vehicle to changes in specific impulse and sea-level thrust-to-weight ratio are examined. The results of a variety of vehicle/propulsion system trades performed on the near-term AMLS SSTO vehicle are also presented.

SEA LEVEL THRUST TO WEIGHT RAT↗
NASA NTRS1994

Trajectory-based heating analysis for the European Space Agency/Rosetta Earth Return Vehicle

A coupled, trajectory-based flowfield and material thermal-response analysis is presented for the European Space Agency proposed Rosetta comet nucleus sample return vehicle. The probe returns to earth along a hyperbolic trajectory with an entry velocity of 16.5 km/s and requires an ablative heat shield on the forebody. Combined radiative and convective ablating flowfield analyses were performed for the significant heating portion of the shallow ballistic entry trajectory. Both quasisteady ablation and fully transient analyses were performed for a heat shield composed of carbon-phenolic ablative material. Quasisteady analysis was performed using the two-dimensional axisymmetric codes RASLE and BLIMPK. Transient computational results were obtained from the one-dimensional ablation/conduction code CMA. Results are presented for heating, temperature, and ablation rate distributions over the probe forebody for various trajectory points. Comparison of transient and quasisteady results indicates that, for the heating pulse encountered by this probe, the quasisteady approach is conservative from the standpoint of predicted surface recession.

RADIATIVE ABLATING FLOWFIELD A↗
NASA NTRS1994

Lunar missions using advanced chemical propulsion: System design issues

To provide the transportation of lunar base elements to the moon, large high-energy propulsion systems will be required. Advanced propulsion systems for lunar missions can provide significant launch mass reductions and payload increases. These mass reductions and added payload masses can be translated into significant launch cost savings for the lunar base missions. The masses in low Earth orbit (LEO) were compared for several propulsion systems: nitrogen tetroxide/monomethyl hydrazine (NTO/MMH), oxygen/methane (O2/CH4), oxygen/hydrogen (O2/H2), and metallized O2/H2/Al propellants. Also, the payload mass increases enabled with O2/H2 and O2/H2/Al systems were addressed. In addition, many system design issues involving the engine thrust levels, engine commonality between the transfer vehicle and the excursion vehicle, and the number of launches to place the lunar mission vehicles into LEO will be discussed. Analyses of small lunar missions launched from a single STS-C flight are also presented.

TRT-THEORETICAL↗
NASA NTRS1994

Probabilistic progressive buckling of trusses

A three-bay, space, cantilever truss is probabilistically evaluated to describe progressive buckling and truss collapse in view of the numerous uncertainties associated with the structural, material, and load variables that describe the truss. Initially, the truss is deterministically analyzed for member forces, and members in which the axial force exceeds the Euler buckling load are identified. These members are then discretized with several intermediate nodes, and a probabilistic buckling analysis is performed on the truss to obtain its probabilistic buckling loads and the respective mode shapes. Furthermore, sensitivities associated with the uncertainties in the primitive variables are investigated, margin of safety values for the truss are determined, and truss end node displacements are noted. These steps are repeated by sequentially removing buckled members until onset of truss collapse is reached. Results show that this procedure yields an optimum truss configuration for a given loading and for a specified reliability.

PROBABILISTIC BUCKLING ANALYSI↗
NASA NTRS1994

Intelsat solar array coupon atomic oxygen flight experiment

A Hughes communications satellite (INTELSAT series) belonging to the INTELSAT Organization was marooned in low-Earth orbit (LEO) on March 14, 1990, following failure of the Titan launch vehicle third stage to separate properly. The satellite, INTELSAT 6, was designed for service in geosynchronous orbit and contains several materials that are potentially susceptible to attack by atomic oxygen. Analysis showed that direct exposure of the silver interconnects in the satellite photovoltaic array to atomic oxygen in LEO was the key materials issue. Available data on atomic oxygen degradation of silver are limited and show high variance, so solar array configurations of the INTELSAT 6 type and individual interconnects were tested in ground-based facilities and during STS-41 (Space Shuttle Discovery, October 1990) as part of the ISAC flight experiment. Several materials for which little or no flight data exist were also tested for atomic oxygen reactivity. Dry lubricants, elastomers, and polymeric and inorganic materials were exposed to an oxygen atom fluence of 1.1 x 10(exp 20) atoms cm(exp 2). Many of the samples were selected to support Space Station Freedom design and decision making. This paper provides an overview of the ISAC flight experiment and a brief summary of results. In addition to new data on materials not before flown, ISAC provided data supporting the decision to rescue INTELSAT 6, which was successfully undertaken in May 1992.

TRT-GENERAL REVIEW↗
NASA NTRS1994

Recent studies of rotorcraft blade-vortex interaction noise

Recent results are presented from several research efforts aimed at the understanding of rotorcraft blade-vortex interaction (BVI) in terms of the noise generation, directivity, and control. The results are based on work performed by NASA Langley Research Center researchers, both alone and in collaboration with other research organizations. Based on analysis of a simplified physical model, the critical parameters controlling BVI noise generation have been identified. The detailed mapping of the acoustic radiation field of a model rotor in a wind tunnel has revealed the extreme sensitivity of directivity to rotor advance ratio and disk attitude. The control and reduction of BVI noise through the use of higher harmonic pitch control is discussed.

BLADE VORTEX INTERACTION↗
NASA NTRS1994

Flight experience with lightweight, low-power miniaturized instrumentation systems

Engineers at the NASA Dryden Flight Research Facility (NASA-Dryden) have conducted two flight research programs with lightweight, low-power miniaturized instrumentation systems built around commercial data loggers. One program quantified the performance of a radio-controlled model airplane. The other program was a laminar boundary-layer transition experiment on a manned sailplane. The purpose of this article is to report NASA-Dryden personnel's flight experience with the miniaturized instrumentation systems used on these two programs. This article will describe the data loggers, the sensors, and the hardware and software developed to complete the systems. It also describes how the systems were used and covers the challenges encountered to make them work. Examples of raw data and derived results will be shown as well. For some flight research applications where miniaturized instrumentation is a requirement, the authors conclude that commercially available data loggers and sensors are viable alternatives. In fact, the data loggers and sensors make it possible to gather research-quality data in a timely and cost-effective manner.

LOW POWER MINIATURIZED INSTRUM↗
NASA NTRS1994

Numerical simulation of incidence and sweep effects on delta wing vortex breakdown

The structure of the vortical flowfield over delta wings at high angles of attack was investigated. Three-dimensional Navier-Stokes numerical simulations were carried out to predict the complex leeward-side flowfield characteristics, including leading-edge separation, secondary separation, and vortex breakdown. Flows over a 75- and a 63-deg sweep delta wing with sharp leading edges were investigated and compared with available experimental data. The effect of variation of circumferential grid resolution grid resolution in the vicinity of the wing leading edge on the accuracy of the solutions was addressed. Furthermore, the effect of turbulence modeling on the solutions was investigated. The effects of variation of angle of attack on the computed vortical flow structure for the 75-deg sweep delta wing were examined. At moderate angles of attack no vortex breakdown was observed. When a critical angle of attack was reached, bubble-type vortex breakdown was found. With further increase in angle of attack, a change from bubble-type breakdown to spiral-type vortex breakdown was predicted by the numerical solution. The effects of variation of sweep angle and freestream Mach number were addressed with the solutions on a 63-deg sweep delta wing.

INCIDENCE↗
NASA NTRS1994

Repeatability of ice shapes in the NASA Lewis icing research tunnel

Tests were conducted in the Icing Research Tunnel (IRT) at the NASA Lewis Research Center to document the current capability of the IRT, focused mainly on the repeatability of the ice shape over a range of icing conditions. Measurements of drag increase due to the ice accretion were also made to document the repeatability of drag. The repeatability of the ice shape was very good at low temperatures, but only fair at near freezing temperatures. In general, drag data shows good repeatability.

SHAPE REPEATABILITY↗
NASA NTRS1994

Model ducted propulsor noise characteristics at takeoff conditions

A model Advanced Ducted Propulsor (ADP) was tested in the NASA Lewis Low-Speed Anechoic Wind Tunnel at a simulated takeoff velocity of Mach 0.2. The model was designed and manufactured by Pratt & Whitney. The 16-blade rotor ADP was tested with 22- and 40-vane stators to achieve cut-on and cut-off criterion with respect to propagation of the fundamental rotor-stator interaction tone. Additional test parameters included three inlet lengths, three nozzle sizes, two spinner configurations, and two rotor rub strip configurations. The model was tested over a range of rotor blade setting angles and inlet angles of attack. Acoustic data were taken with a sideline translating microphone probe and with a unique inlet microphone probe that identified inlet rotating acoustic modes. The beneficial acoustic effects of cut-off were clearly demonstrated. A 10-dB fundamental tone reduction was associated with the long inlet and 40-vane stator. The fundamental tone level was essentially unaffected by inlet angle of attack at rotor speeds of above 96% design.

TRT-EXPERIMENTAL↗
NASA NTRS1994

Simulation and flight test evaluation of head-up-display guidance for harrier approach transitions

Position and speed guidance displays for STOVL aircraft curved, decelerating approaches to hover and vertical landing have been evaluated for their effectiveness in reducing pilot workload and improving performance. The NASA V/STOL Systems Research Aircraft, a modified YAV-8B Harrier prototype, was used to evaluate the displays in flight, whereas the NASA Ames Vertical Motion Simulator was used to extend the flight test results to instrument meteorological conditions (IMC) and to examine performance in various conditions of wind and turbulence. The simulation data showed close correlation with the flight test data, and both demonstrated the feasibility of the displays. With the exception of the hover task in zero visibility, which was level-3, averaged Copper-Harper handling qualities ratings given during simulation were level-2 for both the approach task and the hover task in all conditions. During flight tests in calm and clear conditions, the displays also gave rise to level-2 handling qualities ratings. Pilot opinion showed that the guidance displays would be useful in visual flight, especially at night, as well as in IMC.

HARRIER APPROACH↗
NASA NTRS1994

Interpretation of waverider performance data using computational fluid dynamics

A computational study was conducted to better understand experimental results obtained from wind-tunnel tests of a Mach 4 conical-flow-derived waverider and a comparative reference configuration, which showed that the aerodynamic performance of the reference configuration was slightly better than that of the waverider. The computational results showed that the predicted surface pressure values and the integrated lift and drag coefficients were much lower for the reference model because the reference model bottom is an expansion surface. However, the lift-drag ratios for the reference model were higher due to a relatively low drag for a comparable amount of lift. The results also showed that the reference model exhibited the same shock attachment characteristics as the conical-flow-derived waverider, and is therefore also a waverider. The shock attachment characteristic gives the waverider a performance advantage over conventional hypersonic vehicles, and the results suggest that altering the bottom surface does not cause significant performance degradation. Flowfield solutions also show that the conical-flow waverider model has better propulsion/airframe integration characteristics than the reference configuration. The results also suggest that generating flowfields other than conical ones may be used to design waveriders with improved aerodynamic performance.

COMPUTATIONAL FLUID DYNAMICS↗
NASA NTRS1994

Development and flight test of a deployable precision landing system

A joint NASA Dryden Flight Research Facility and Johnson Space Center program was conducted to determine the feasibility of the autonomous recovery of a spacecraft using a ram-air parafoil system for the final stages of entry from space that included a precision landing. The feasibility of this system was studied using a flight model of a spacecraft in the generic shape of a flattened biconic that weighed approximately 150 lb and was flown under a commercially available, ram-air parachute. Key elements of the vehicle included the Global Positioning System guidance for navigation, flight control computer, ultrasonic sensing for terminal altitude, electronic compass, and onboard data recording. A flight test program was used to develop and refine the vehicle. This vehicle completed an autonomous flight from an altitude of 10,000 ft and a lateral offset of 1.7 miles that resulted in a precision flare and landing into the wind at a predetermined location. At times, the autonomous flight was conducted in the presence of winds approximately equal to vehicle airspeed. Several novel techniques for computing the winds postflight were evaluated. Future program objectives are also presented.

TRT-EXPERIMENTAL↗
NASA NTRS1994

Response of a grounded dielectric slab to an impulse line source using leaky modes

This paper describes how expansions in leaky (or improper) modes may be used to represent the continuous spectrum in an open radiating waveguide. The technique requires a thorough knowledge of the life history of the improper modes as they migrate from improper to proper Riemann surfaces. The method is illustrated by finding the electric field resulting from an impulsively forced current located in the free space above a grounded dielectric slab.

DIELECTRIC SLABS↗
NASA NTRS1994

Ampoule failure sensor development for semiconductor crystal growth experiments

Currently there are no devices to detect an ampoule failure in semiconductor crystal growth experiments. If an ampoule fails, it will go undetected until the containing cartridge is breached due to chemical degradation. The experiment will then be terminated resulting in a failed experiment and a loss of data. The objective of this research was to develop a reliable failure sensor that would detect a specific liquid or vapor material before the metallic cartridge is degraded and the processing furnace contaminated. The sensor is a chemical fuse made from a metal with which the semiconductor material reacts more rapidly than it does with the containing cartridge. Upon ampoule failure, the sensor is exposed to the vapor or liquid semiconductor and the chemical reaction causes a resistance change in the sensor material. The sensor shows a step change in resistance on the order of megohms when exposed to mercury zinc telluride (HgZnTe), mercury cadmium telluride (HgCdTe), or gallium arsenide (GaAs). This ampoule failure sensor is being tested for possible use on the second United States Microgravity Mission (USML-2) and is the subject of a NASA patent application.

CHEMICAL FUSE↗
NASA NTRS1994

Aerothermodynamic methods for a Mars environmental survey Mars entry

Computational fluid dynamics models for the thermodynamics and transport properties used in an equilibrium version of the Langley aerothermodynamics upwind relaxation algorithm (LAURA) for Mars atmospheric entries are described. In addition, the physical models used in a nonequilibrium version of LAURA for Mars-entry flows are described. Uncertainties exist in defining constants used in the transport properties for the equilibrium model and in many of the physical models for the nonequilibrium version. Solutions from the two codes using the best available constants are examined at the Mars-entry conditions characteristics of the Mars environmental survey mission. While the flowfields are near thermal equilibrium, chemical nonequilibrium effects are present in the entry cases examined. Convective heating at the stagnation point for these flows (assuming fully catalytic wall boundary conditions) is approximately 100 W/cm(exp 2). Radiative heating is negligible.

AEROTHERMODYNAMIC METHODS↗