Search NASA⌕ Search

SEARCH · Search NASA

Results for “ZINC ALLOYS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

The effect of zinc additions on the environmental stability of Alloy 8090 (Al-Li-Cu-Mg-Zr)

Stress corrosion cracking (SCC) remains a problem in both Al-Li and conventional Al heat treatable alloys. It has recently been found that relatively small additions (less than or approximately 1 wt-percent) of Zn can dramatically improve the SCC performance of alloy 8090 (Al-Li-Cu-Mg-Zr). Constant load time to failure experiments using cylindrical tensile samples loaded between 30 and 85 percent of TYS indicate improvements of orders of magnitude over the baseline 8090 for the Zn-containing alloys under certain aging conditions. However, the toughnesses of the alloys were noticeably degraded due to the formation of second phase particles which primarily reside on grain and subgrain boundaries. EDS revealed that these intermetallic particles were Cu and Zn rich. The particles were present in the T3 condition and were not found to be the result of quench rate, though their size and distribution were. At 5 hours at 160 C, the alloys displayed the greatest susceptibility to SCC but by 20 hours at 160 C the alloys demonstrated markedly improved TTF lifetimes. Aging past this time did not provide separable TTF results, however, the alloy toughnesses continued to worsen. Initial examination of the alloys microstructures at 5 and 20 hours indicated some changes most notably the S' and delta' distributions. A possible model by which this may occur will be explored. Polarization experiments indicated a change in the trend of E(sub BR) and passive current density at peak aging as compared to the baseline 8090. Initial pitting experiments indicated that the primary pitting mechanism in chloride environments is one occurring at constituent (Al-Fe-Cu) particles and that the Cu and Zn rich boundary precipitates posses a breakaway potential similar to that of the matrix acting neither anodic or cathodic in the first set of aerated 3.5 w/o NaCl experiments. Future work will focus on the identification of the second phase particles, evaluation of K(sub 1SCC) and plateau da/dt via both DCB and slow strain rate techniques. A lower Zn content variant will be examined in the near future in hopes of optimizing toughness, density and SCC performance.

Kilmer, Raymond J.↗
NASA NTRS1966

Use of steel and tantalum apparatus for molten Cd-Mg-Zn alloys

Steel and tantalum apparatus contains various ternary alloys of cadmium, zinc, and magnesium used in pyrochemical processes for the recovery of uranium-base reactor fuels. These materials exhibit good corrosion resistance at the high temperatures necessary for fuel separation in liquid metal-molten salt solvents.

Bennett, G. A.↗
NASA NTRS1974

Skylab experiments on metals

The Skylab Materials Processing Facility is described. Eight experiments on metal processing under near-zero-gravity conditions were performed in this facility. Three of these involved metals and procedures of potential application to fabrication in space. A Multipurpose electric furnace within the Materials Processing Facility was employed to heat three ampoules of samples for each of the other five experiments. These five investigations cover diffusion versus convection rates in molten zinc, several immiscible alloy compositions, a whisker-reinforced silver-based composite, heat treating of porous silver samples, and a copper-aluminum eutectic.

Lundquist, C. A.↗
NASA NTRS1999

Orbital Processing of High-Quality Zn-Alloyed CdTe Compound Semiconductors

The objective of this research is to investigate the influences of gravitationally-dependent phenomena (hydrostatic and buoyant) on the growth and quality of doped and alloyed Cadmium-Zinc-Telluride (CdZnTe) crystals grown by the modified seeded Bridgman-Stockbarger technique. It is hypothesized that the damping of the gravitationally-dependent buoyancy convection will substantially enhance chemical homogeneity and the near-elimination of hydrostatic pressure will enable significant reduction in defect (dislocations and twins) density.

Larson, David J., Jr.↗
DOE OSTI2024

AP-XPS Study of the Reaction of O 2 and CO 2 with Zn–Au(111) Surface Alloys: Activation of O–O/C–O Bonds and the Formation of ZnO

Synchrotron-based ambient-pressure X-ray photoelectron spectroscopy (AP-XPS) was used to study the dissociation of O 2 and CO 2 on Zn-Au(111) alloys which contained 0.2-0.3 monolayers of zinc. Although Au(111) is inert, the alloys displayed a high activity for the cleavages of O-O and C-O bonds at room temperature with the formation of ZnO x species. Dissociative adsorption of O 2 at 300 K destroyed the alloys and the results of AP-XPS pointed to the co-existence of two types of oxygen species on the surface: ZnO x and chemisorbed O atoms (O chem ) on Au or the Au-ZnO interface. Annealing from room temperature to 600 K induced a O chem → ZnO x transformation that reflected the poor stability of O atoms on Au(111). The Zn-Au(111) systems exhibited a reactivity towards CO 2 that was much larger than that seen for Au(111), Cu(111) or surfaces of late transition metals like, Ni, Pd or Pt. At 300 K, CO 2 underwent partial dissociation depositing large amounts of O chem on the surface with minor formation of ZnO x . In addition, the deposited O chem reacted with CO 2 to form surface carbonate groups. Dosing of CO 2 at 500-600 K mainly led to the formation of ZnO x and the surface carbonate almost disappeared. In the presence of hydrogen, i.e. reaction feeds with a CO 2 to H 2 ratio of 1:3, the surface chemistry at 300 K was very similar to that seen for pure CO 2 with the formation of ZnO x and carbonate groups. In contrast, at 500-600 K, reaction with hydrogen induced the removal of ZnO x and CO 3 /HCOO species. Finally, our AP-XPS results are consistent with the idea that CO 2 hydrogenation on AuZn alloys involves a redox process where there is sequential oxidation by CO 2 and reduction by H 2 to yield methanol.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Cationic Copper Species Stabilized by Zinc during the Electrocatalytic Reduction of CO 2 Revealed by In Situ X‐Ray Spectroscopy

Abstract Advanced in situ X‐ray absorption spectroscopy characterization of electrochemically co‐electrodeposited bi‐element copper alloy electrodes shows that zinc yields the formation of a stable cationic Cu species during the electroreduction of CO 2 at high cathodic polarization. In contrast, the formation/stabilization of cationic Cu species in copper oxides, or doping Cu with another element, like Ni, is not possible. It is found that the pure and mixed Cu:Zn electrodes behave similarly in term of electrocatalytic selectivity to multi‐carbon products. At higher Zn concentrations the electrode behaves like the pure Zn catalyst, which indicates that the Cu cationic species do not have a significant influence on the selectivity to multi‐carbon products. It is found that in the non‐monotonically distribution of products is dominated in term of surface energy in which copper prefers the surface. Otherwise, this work highlights the importance of in situ characterization to uncover the mechanisms mediating the catalytic reactions in contrast to ex situ or post mortem analysis, which can be a source of misinterpretation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Comparative Study of Zinc Cold-Spray Coating and Pre-treatments for Magnesium Alloys

Magnesium (Mg) alloys are appealing for automotive lightweighting owing to their high specific strength. However, their susceptibility to corrosion in harsh environments remains a major challenge. Conventional industrial pre-treatment coatings, including zinc phosphate, chromate conversion, and non-chromate conversion, often exhibit discontinuities and microcracks, leading to localized corrosion near fasteners and parting lines. Here, this study investigates cold-sprayed zinc (Zn) coatings as a novel pre-treatment alternative for high-pressure die cast (HPDC) AZ91 Mg alloys, demonstrating significant improvements in wear and corrosion performance. Cold spray produces uniform and robust coatings, reducing wear rate by over 50% and reducing corrosion rate by over 99.3%, as measured by evolved hydrogen release, compared to traditional pre-treatments. Multimodal corrosion testing reveals that Zn cold-spray coatings form a protective layer during exposure, minimizing general and filiform corrosion, and exhibiting corrosion potential (E corr ) that is nobler by ~ 400 mV than the surfaces of both pre-treated and uncoated AZ91. Scalability of cold spray for selective application around multimaterial joints further strengthens their industrial viability. This work establishes Zn cold-spray coatings as highly effective pre-treatment solutions for the advancement of corrosion resistant Mg alloy components in automotive applications.

multimodal corrosion↗
DOE OSTI2022

Investigation on the AgPt and AgPd hybrid alloy nanoparticles (HANPs) for the hybrid MoS 2 /ZnO/HANP UV photodetector application

We report hybrid photodetectors made of two or more nanomaterial components can offer the high potential for advanced photodetection applications with enhanced light absorption, improved efficiency and structural tunability. A hybrid UV photodetector (PD) configuration incorporating the plasmonic hybrid alloy nanoparticles (HANP), ZnO quantum dots (QDs) and MoS 2 nanoflakes, namely MoS2/ZnO/HANP PD, is demonstrated. The optimized MoS 2 /ZnO/HANP PD exhibits a high photocurrent of 5.66 mA at 0.34 mW/mm 2 under 385 nm illumination with two orders of improvement from the bare ZnO, which is one of the highest photocurrents by the ZnO-based PDs. It also demonstrates high figure-of-merits with the responsivity of 14,523 mA/W, detectivity of 8.13 x 10 11 jones, and external quantum efficiency (EQE) of 4,680 %, outperforming most of the ZnO-based hybrid architectures. The enhanced photoresponse is primarily attributed to the significantly enhanced hot electron generation by the AgPd HANPs and photocarrier collection through the ZnO QD layer. MoS 2 nanoflakes also provide additional photon absorption sites and boost the photo-carrier transfer process. HANPs are grown by adapting a dual-step solid-state dewetting process (SSD) approach and the superiority of AgPd HANPs is confirmed by systematic investigation, FDTD simulation and comparison of AgPt and AgPd HANPs.

MoS2↗
DOE OSTI2026

Synthesis and Evaluation of Cu@ZnO Core@Shell Nanowires for Use in the Carbon Dioxide Thermal Reduction Reaction

Copper-based core@shell nanomaterials are of interest for the catalytic hydrogenation of carbon dioxide toward value-added products. In this context, we have developed a facile, microwave-based procedure for the reliable and reproducible synthesis of Cu@ZnO core@shell nanowires. A systematic assessment of the effect of rationally varying various reaction conditions on this protocol was completed in order to better evaluate the growth process of these core–shell motifs. We determined that among different reaction parameters, it was the critical role of reaction time which enabled the quantitatively reliable growth of external shells with tunable thicknesses of up to 20 nm. As a demonstration of the material’s practical viability, catalytic testing was subsequently performed for the reverse water–gas shift reaction (CO 2 + H 2 → CO + H 2 O), with the evolution of the process followed with in situ X-ray diffraction and X-ray absorption spectroscopy in order to probe structural changes and gauge stability. These tests found the catalysts to be effective at converting CO 2 to CO, with notable stability detected in the shell layer and no observed alloying between copper and zinc. Furthermore, our studies support the idea that the Cu–ZnO and CuO x –ZnO interfaces are essential for the effective activation of CO 2 and H 2 .

36 MATERIALS SCIENCE↗
NASA NTRS1965

Galvanic corrosion reduced in aluminum fabrications

Titanium alloy fasteners dipped at zinc chromate primer are installed while wet in protective coated aluminum panels to reduce galvanic corrosion. Moisture tight seals at fastener points are also provided.

Source record↗
NASA NTRS1981

InGaAsP/InP laser development for single-mode, high-data-rate communications

Materials studies as well as general and specific device development were carried out in the InGaAsP system. A comparison was made of three standard methods of evaluating substrate quality by means of dislocation studies. A cause of reduced yield of good wafers, the pullover of melt from one bin to the next, has been analyzed. Difficulties with reproducible zinc acceptor doping have been traced to segregation of zinc in the In/Zn alloy used for the doping source. Using EBIC measurments, the pn junction was shown to drift in location depending on factors not always under control. An analysis of contact structures by SIMS showed that the depth to which the sintered Au/Zn contact penetrates into the structure is typically 0.13 microns, or well within the cap layer and out of the p-type cladding and thus not deleterious to laser prformance. The problem of single-mode laser development was investigated and it was shown to be related to the growth habit over four different possible substrate configurations. The fabrication of constricted double heterojunctions, mesa stripe buried heterostructures, and buried heterostructures was discussed, and measurements were presented on the device properties of single-mode buried heterostructure lasers. Results include single spectral line emission at 3 mW and a threshold current of 60 mA.

Ladany, I.↗
NASA NTRS1990

The effects of zinc addition on the environmental stability of Al-Li alloys

It was found that relatively small addition of Zn can improve the stress corrosion cracking (SCC) resistance of Al-Li alloys. However, the mechanism by which this is accomplished is unclear. The role that Zn plays in altering the behavior of Alloy 8090 is investigated. Early results suggest that Zn additions increase the volume fraction of delta(Al3Li) precipitation and differential scanning calorimetry (DSC) on these alloys confirms this. The four alloys studied each had initial compositions lying in the 8090 window and had varying amounts of Zn added to them. Alloy 8090, like other Al-Li alloys, displays a delta' precipitate free zone (PFZ) upon artificial aging along the grain and subgrain boundaries. However Zn additions greatly decreased or eliminated a delta' PFZ after 100 hours at 160 C. This implies that the subgrain boundary precipitation kinetics are being altered and suppressed. Furthermore, there appears to be a window of Zn concentration above which a delta ' PFZ can reappear with the nucleation and growth of a currently unidentified precipitate on the boundaries. Polarization experiments were performed and the results presented. The experiments were performed in deaerated 3.5 w/o NaCl in both as received (T3) condition and at peak aging of 100 hours at 160 C. The aging profile was determined via Vickers Hardness tests.

Kilmer, Raymond J.↗
DOE OSTI2021

Stable bismuth-antimony alloy cathode with a conversion-dissolution/deposition mechanism for high-performance zinc batteries

Although a large number of intercalation cathode materials for aqueous Zn batteries have been reported, limited intercalation capacity precludes achieving a higher energy density. Here, for this work, we develop a high-performance aqueous Zn battery based on BiSb alloy (Bi 0.5 Sb 0.5 ) using a high-concentrated strong-basic polyelectrolyte. We demonstrate that a conversion-dissolution/deposition electrochemical mechanism (BiSb ↔ Bi + SbO 2 – ↔ Bi + SbO 3 – ↔ Bi 2 O 3 ) through in situ X-ray diffraction (XRD), Raman, and ex-situ X-ray photoelectron spectrometry (XPS) characterizations with the help of density functional theory calculations. The BiSb cathode delivers large capacity of 512 mAh g –1 at 0.3 Ag –1 and superior rate capability of 90 mAh g –1 even at 20 Ag –1 , and long-term cyclability with capacity retentions of 184 mAh g –1 after 600 cycles at 0.5 Ag –1 and 130 mAh g –1 after 1300 cycles at 1 Ag –1 . Remarkably, even at temperatures as low as –10 and –20 °C, capacities of 210 and 197 mAh g –1 are reserved at 1 Ag –1 , respectively. Moreover, the prepared pouch Zn//BiSb battery delivers a high energy density of 303 Wh kg –1 BiSb at 0.3 Ag –1 . When coupled with a high concentration polyelectrolyte, the Zn/BiSb battery exhibits an excellent performance over a wide temperature range (–40 to 40 °C). Our research reveals the metal cathode is promising for Zn batteries to achieve a high performance with the unique mechanism and alloys can be an effective approach to stabilize metal electrodes for cycling.

25 ENERGY STORAGE↗
NASA NTRS1991

Electrodeposited Zinc-Nickel as an Alternative to Cadmium Plating for Aerospace Application

Corrosion evaluation studies were conducted on 4130 alloy steel samples coated with electrodeposited zinc-nickel and samples coated with electrodeposited cadmium. The zinc nickel was deposited by the selection electrochemical metallizing process. These coated samples were exposed to a 5-percent salt fog environment at 35 plus or minus 2 C for a period ranging from 96 to 240 hours. An evaluation of the effect of dichromate coatings on the performance of each plating was conducted. The protection afforded by platings with a dichromate seal was compared to platings without the seal. During the later stages of testing, deposit adhesion and the potential for hydrogen entrapment were also evaluated.

Mcmillan, V. C.↗
DOE OSTI2024

Upcycled high-strength aluminum alloys from scrap through solid-phase alloying

Although recycling secondary aluminum can lead to energy consumption reduction compared to primary aluminum manufacturing, products produced by traditional melt-based recycling processes are inherently limited in terms of alloy composition and microstructure, and thus final properties. To overcome the constraints associated with melting, we have developed a solid-phase recycling and simultaneous alloying method. This innovative process enables the alloying of 6063 aluminum scrap with copper, zinc, and magnesium to form a nanocluster-strengthened high-performance aluminum alloy with a composition and properties akin to 7075 aluminum alloy. The unique nanostructure with a high density of Guinier-Preston zones and uniformly precipitated nanoscale η‘/Mg(CuZn) 2 strengthening phases enhances both yield and ultimate tensile strength by >200%. By delivering high-performance products from scrap that are not just recycled but upcycled , this scalable manufacturing approach provides a model for metal reuse, with the option for on-demand upcycling of a variety of metallic materials from scrap sources.

36 MATERIALS SCIENCE↗