Search NASA⌕ Search

SEARCH · Search NASA

Results for “burn window”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Fire-Resistant Belt Panel for Airplane Windows

Window-belt panel for airplanes fire resistant and generates little smoke when exposed to flames. Panel incorporates fire-shield layer adding minimal weight but delays or prevents fire from burning through. Structural core of panel is Nomex or equivalent polyamide paper honeycomb. Fire shield, made of fluororubber sheet, incorporated in multiple-ply facing bonded to core. Outer layers of multiple-ply facing and back face of panel consist of biwoven carbon-cloth impregnated with phenolic resin.

Trabold, E. L.↗

Atlas/Centaur-29 Intelsat IV (F5) flash flight report

ATLAS/CENTAUR-29 was launched from ETR Complex 36B, June 13, 1972, at a flight azimuth of 101 degrees. The ETR test number was 1240. The launch vehicle consisted of an ATLAS SLV-3C first stage and a CENTAUR second stage. The spacecraft was INTELSAT 4 (F-5). The launch occurred at the opening of the window. Indications are that the spacecraft was injected into the required transfer orbit and has achieved it's final orbit. All orbital parameters were extremely close to nominal. A nominal apogee motor burn took place at 2101 EDT on June 14, 1972 at 124 degrees East longitude and the final duty station of the spacecraft will be at 62 degrees East longitude. A two week communications checkout was started on or about June 15, 1972.

Source record↗

LADEE Preparations for Contingency Operations for the Lunar Orbit Insertion Maneuver

The Lunar Atmosphere and Dust Environment Explorer (LADEE) spacecraft was launched on September 6, 2013, and completed its mission on April 17, 2014 with a directed impact to the Lunar Surface. Its primary goals were to examine the lunar atmosphere, measure lunar dust, and to demonstrate high rate laser communications. The LADEE mission was a resounding success, achieving all mission objectives, much of which can be attributed to careful planning and preparation. This paper discusses the specific preparations for fault conditions that could occur during a highly-critical phase of the mission. To get to the Moon, the spacecraft traversed multiple phasing loops around the Earth, and then executed a breaking maneuver to achieve lunar orbit. This Lunar Orbit Insertion (LOI) maneuver was perhaps the most time-critical phase of the entire mission. The LOI maneuver had to occur within a twenty minute window in order to achieve lunar orbit with an acceptable amount of propellant remaining. Missing this window would have likely resulted in a loss of the entire mission. An additional challenge of the maneuver was that spacecraft was out of view for approximately one hour prior to the main thruster burn, with the burn needing to occur within five minutes after coming into view. These conditions resulted in unique challenges for ground operations and the fault management system. Early in the planning stages of the mission, the criticality and challenges of this maneuver were evident to the system designers. The major concern was that any triggering of the on-board fault management system, whether it is in response to a true fault or a false positive, would result in an unacceptable delay to the burn. Therefore the flight software was designed with a flexible fault management system, such that any or all of the fault management responses could be disabled for the lead up and execution of the maneuver. Later, a triage was conducted to develop a list of fault responses, mapped to various parts of the timeline of the maneuver. Some of these contingency responses were solely ground-based if the time to detect, diagnose, and respond were adequate. Other responses were automated on-board if the response time from the ground would have been inadequate. For instance, in order to recover from a system reboot, on-board automation would have automatically reconfigured the spacecraft for the burn and reoriented the spacecraft to the burn attitude.These contingency responses were practiced, over and over, during numerous rehearsals. Although the LOI maneuver was executed without having to use any of these contingencies, the LADEE team was adequately prepared for this highly critical phase of the mission.

Cannon, Howard↗

Timing the Flames: Geostationary Satellite Detection of Diurnally Shifting Stubble Burning in Northwestern India

Post-monsoon open-field stubble burning in northwestern (NW) India—a key agricultural region known as the “breadbasket”—is a longstanding practice used to clear fields. Satellite observations spanning over two decades have revealed significant upward trends in crop production, vegetative greenness, and the frequency of post-harvest fires, with this last contributing to hazardous air quality during the peak burning season (mid-October to mid-November). Since 2022, thermal anomaly data from Aqua-MODIS and SNPP-VIIRS sensors have shown a sharp decline in reported fire events—an observation that contrasts starkly with the concurrent rise in regional aerosol loading detected from space. This apparent discrepancy became particularly pronounced in 2024–2025, prompting a closer examination using high-temporal-resolution imagery from the Advanced Meteorological Imager (AMI) on the geostationary satellite GEO-KOMPSAT-2A. These observations revealed a clear spike in fire-related signals occurring around and after 4:00 p.m. local time, i.e., outside the typical noon to 2:00 p.m. detection window of the MODIS and VIIRS. A fire detection algorithm exploiting the fire-sensitive shortwave-infrared 3.8 μm signal and its contrast to 11.2 μm infrared observations is designed to adopt AMI observations and applied to its multi-year observations (2019–2025). The resulting fire dataset unambiguously shows a gradual shift in stubble burning activity toward the late afternoon hours beginning in 2022 which is underreported by polar-orbiting satellites. The orbital drift of NASA’s MODIS sensor on the Aqua platform allows detection of some of the gradually shifting fires during afternoon hours, but the MODIS still misses a large number of fires occurring around and after 4 p.m. The AMI’s relatively coarse spatial resolution (~4 km), a consequence of its slant viewing geometry over NW India, imposes inherent limitations on quantifying the full extent of fire occurrences. The operational air quality forecasting models currently assimilate satellite fire detections predominantly captured during early afternoon overpasses of the MODIS and VIIRS. The temporal shift in fire activity complicates such forecast, leading to a substantial underestimation of emissions. Intense stubble burning and the resulting air pollution highlight the need for effective crop residue management practices for mitigating the frequency of open biomass burning and thereby reducing episodic degradation of air quality and its associated public health and economic impacts.

post-monsoon stubble burning; northwestern India;↗

Imaging Fluorescent Combustion Species in Gas Turbine Flame Tubes: On Complexities in Real Systems

Planar laser-induced fluorescence (PLIF) is used to visualize the flame structure via OH, NO, and fuel imaging in kerosene- burning gas turbine combustor flame tubes. When compared to simple gaseous hydrocarbon flames and hydrogen flames, flame tube testing complexities include spectral interferences from large fuel fragments, unknown turbulence interactions, high pressure operation, and the concomitant need for windows and remote operation. Complications of these and other factors as they apply to image analysis are considered. Because both OH and gas turbine engine fuels (commercial and military) can be excited and detected using OH transition lines, a narrowband and a broadband detection scheme are compared and the benefits and drawbacks of each method are examined.

Hicks, Y. R.↗

Predictive binder jet additive manufacturing enabled by clean burn-off binder design

Binder jet additive manufacturing (BJAM) presents an avenue for advanced manufacturing of various high-value materials due to high deposition rates, scalability, and geometric flexibility. However, conventional organic binders in BJAM introduce residual carbon upon pyrolysis, often leading to imprecise alloy composition in the final sintered part. The undesirable residual carbon from binder burn-off limits the application of BJAM for high-performance alloys due to their high sensitivity to carbon addition. In this study, we have designed poly(vinylpyrrolidone-co-vinyl acetate) (PVP-VAc) as a clean burn-off binder for BJAM, where excess oxygen groups in VAc enable cleaner burn-off and reduce residual carbon retention. Compared to a widely used commercial binder, the optimized PVP-VAc binder reduced residual carbon retention by over 90% in H13 tool steel. The significant reduction in residual carbon enables predictable printing and subsequent sintering of complex H13 tool steel geometries, an alloy known to have substantial challenges around distortion due to the sintering window shifting from carbon addition. The design of a clean burnout binder provides a major path forward for BJAM by enabling new AM designs and applications for composition-sensitive high-performance alloys, such as nickel-based superalloys, titanium alloys, and high alloyed steels.

36 MATERIALS SCIENCE↗

NASA GRC's High Pressure Burner Rig Facility and Materials Test Capabilities

The High Pressure Burner Rig (HPBR) at NASA Glenn Research Center is a high-velocity. pressurized combustion test rig used for high-temperature environmental durability studies of advanced materials and components. The facility burns jet fuel and air in controlled ratios, simulating combustion gas chemistries and temperatures that are realistic to those in gas turbine engines. In addition, the test section is capable of simulating the pressures and gas velocities representative of today's aircraft. The HPBR provides a relatively inexpensive. yet sophisticated means for researchers to study the high-temperature oxidation of advanced materials. The facility has the unique capability of operating under both fuel-lean and fuel-rich gas mixtures. using a fume incinerator to eliminate any harmful byproduct emissions (CO, H2S) of rich-burn operation. Test samples are easily accessible for ongoing inspection and documentation of weight change, thickness, cracking, and other metrics. Temperature measurement is available in the form of both thermocouples and optical pyrometery. and the facility is equipped with quartz windows for observation and video taping. Operating conditions include: (1) 1.0 kg/sec (2.0 lbm/sec) combustion and secondary cooling airflow capability: (2) Equivalence ratios of 0.5- 1.0 (lean) to 1.5-2.0 (rich), with typically 10% H2O vapor pressure: (3) Gas temperatures ranging 700-1650 C (1300-3000 F): (4) Test pressures ranging 4-12 atmospheres: (5) Gas flow velocities ranging 10-30 m/s (50-100) ft/sec.: and (6) Cyclic and steady-state exposure capabilities. The facility has historically been used to test coupon-size materials. including metals and ceramics. However complex-shaped components have also been tested including cylinders, airfoils, and film-cooled end walls. The facility has also been used to develop thin-film temperature measurement sensors.

Robinson, R. Craig↗

Empire. a study of early manned interplanetary missions final report, may 26 - nov. 25, 1962

This report summarizes the investigations and results of the EMPIRE Study Program undertaken by Aeronutronic Division of Ford Motor Company for the Future Projects Office, Marshall Space Flight Center, under Contract NAS8-5025. The dual planet flyby missions of the Crocco and Symmetric trajectory classes are discussed. The Crocco mission with an August 1971 launch window requires an interplanetary injection velocity increment of i0.i km/sec, has a return velocity of 13.5 km/sec, and takes approximately 400 days. The Symmetric mission with a July 1970 launch window has an injection velocity increment of 5.3 km/sec, a return velocity of 15.8 km/sec, and takes approximately 630 days. Additional results of the trajectory studies and abort trajectories are reported. The guidance and navigation subsystem, midcourse corrections, and planetary approach corrections are discussed. A detailed analysis of the reentry phase of EMPIRE includes consideration of an Apollo-type, a Drag Brake, and a lifting-type reentry vehicle to return the six-man crew at mission completion or in an aborted condition. The High L/D reentry vehicle is used in the missions considered. The various technological areas required for design criteria are developed and several spacecraft designs are considered. The all chemical propulsion Crocco system is discarded due to weight, complexity, and cost. The nuclear injected Crocco is treated in a similar manner. The lower energy injection for the Symmetric Mission leads to the feasibility of a nuclear injected vehicle with an Earth orbit weight of about 180,000 kilograms (400,000 pounds) before interplanetary transit. In addition, two chemical symmetric vehicles are treated. Conservative radiation exposures are derived, for the 630 day mission, of less than 200 REM and a polyethelene radiation shelter is designed. Scientific aspects of the missions are discussed. Mission Success Probabilities are presented for the various missions considered and for Saturn C-5, Nova, and Super-Nova Earth launch vehicles in light of possible development. The need for acceleration of nuclear rocket engine developments and auxiliary power developments is indicated. Definition of a larger nuclear engine of the order of 200,000 pounds thrust and about 800 seconds burning time or 50,000 pound thrust and 3600 seconds burning time is indicated for the Symmetric Mission in 1970 (energy requirements are higher in 1972 and for later launch due to the less favorable position of Mars)_ Immediate development of this advanced nuclear propulsion capability is recommended. A Development Plan and Funding Schedule is given for the 1970 launch window pinpointing the critical development areas and indicating a total program cost of $12.6 billion independent of other programmed R&D costs. In conclusion, technological feasibility for an early manned dual planet Mars-Venus flyby is believed to be demonstrated in this study. Several areas of accelerated development and experimental confirmation of theory are pinpointed. The necessary funding and development of Nova or orbital operations capability with Saturn C-5's is required. The 1970 launch window appears to offer the least expensive Symmetric Mission for several years into the 1980's.

F. P. Dixon↗

Effect of fuel molecular structure on soot formation in gas turbine combustion

The effect of fuel variations at the same hydrogen content on the formation of soot in a gas turbine combustor was studied. Six fuels were burned to a combustor over a matrix of about 50 test conditions with test conditions ranging over 500-1800 kPa (5-18 atm) pressure and 500-1000 K burner inlet temperature; fuel-air ratios were varied from 0.008-0.024. Flame radiation measurements were made through a sapphire window toward the end of the primary zone. The hydrogen content of the six test fuels ranged from 12.80 to 12.88%. Five fuels emphasized hydrocarbon types: (mono, di, and tricyclic), naphthenes (decalin) and partially hydrogenated aromatics (tetralin); the sixth fuel emphasized final boiling point.

Naegeli, D. W.↗

Development of a Pulsed Combustion Actuator For High-Speed Flow Control

This paper describes the flow within a prototype actuator, energized by pulsed combustion or detonations, that provides a pulsed jet suitable for flow control in high-speed applications. A high-speed valve, capable of delivering a pulsed stream of reactants a mixture of H2 and air at rates of up to 1500 pulses per second, has been constructed. The reactants burn in a resonant chamber, and the products exit the device as a pulsed jet. High frequency pressure transducers have been used to monitor the pressure fluctuations in the device at various reactant injection frequencies, including both resonant and off-resonant conditions. The combustion chamber has been constructed with windows, and the flow inside it has been visualized using Planar Laser-Induced Fluorescence (PLIF). The pulsed jet at the exit of the device has been observed using schlieren.

Cutler, Andrew D.↗

Noachian Impact Breccias on the Rim of Endeavour Crater, Mars: Opportunity APXS Results

Mars Exploration Rover Opportunity has been investigating the geology of Meridiani Planum since January 2004, and is currently approx. 3830% into its primary mission. Opportunity reached the rim of 22 km diameter Endeavor crater at Spirit Point on the south end of Cape York on sol 2681 and began exploring the geology of Endeavour rim. She left Cape York on sol 3316 and arrived at the next rim remnant to the south, Solander Point, on sol 3387 to begin geological investigations at the contact and up onto Murray Ridge. The Burns fm. of Meridiani Planum lies near the top of the plains-forming unit of western Sinus Meridiani and onlaps onto the Endeavour rim rocks (hereafter rim rocks). Endeavour crater would have excavated approx. 4 km into the existing stratigraphy. Thus, the ejecta that form the rim rocks offer windows into the deeper lithologies of Sinus Meridiani. Here we discuss the polymict breccias of the Shoemaker fm. on Cape York and the breccias from Murray Ridge, with a focus on compositions determined by the Alpha Particle X-Ray Spectrometer (APXS).

Mittlefehldt, D. W.↗

Aeroassisted orbit transfer window opens on missions

Studies of aeroassisted spacecraft orbit transfer conducted over the last two decades have produced an extensive literature and a well developed technology base, which suggest the obtainability of substantial performance improvements over all-propulsive spacecraft maneuvers. In such cases as that of multipass aerobraking, in which the vehicle is transferred from its approach velocity to a highly elliptic orbit about the planet by means of a rocket burn, followed by the circularization of the orbit through many high altitude atmospheric passes, the technology appears to be ready for application. In most other areas of aeroassisted orbit transfer, further work is required to reduce design risks to acceptable levels.

Walberg, G. D.↗

Fabrication, oxidation, and combustion of nanoscale magnesium diboride and tetraboride

The difficult ignition of boron decreases the combustion efficiency of boron-loaded, fuel-rich propellants. One approach to solving this problem involves the use of magnesium diboride (MgB2), which ignites easier than boron. Magnesium tetraboride (MgB4) offers greater energy density owing to its higher boron content. However, the effect of B/Mg ratio on the ignition and combustion is unknown. Additionally, while nanoscale MgB₂ particles and quasi-2D structures were recently recognized as promising energetic additives, the oxidation and combustion properties of nanoscale MgB₄ have not been explored. The objectives of the present work included synthesis, purification, and high-energy ball milling of MgB2 and MgB4 powders as well as investigation of their thermal decomposition, oxidation, and combustion. The MgB2 and MgB4 powders were fabricated by combustion synthesis in the chemical oven mode and by heating Mg/B mixtures in a tube furnace. The latter method was superior in the synthesis of MgB4. Oxide impurities in the synthesized powders were removed by acid leaching. Nanoscale powders were obtained by high-energy ball milling. Thermal decomposition and oxidation of the obtained MgB₂ and MgB₄ powders were investigated by conducting non-isothermal thermogravimetric analysis (TGA) at temperatures up to 1550 °C in argon and oxygen flows. Combustion of B, MgB₂, and MgB₄ powders with oxygen at atmospheric pressure was studied in a windowed chamber using laser ignition and high-speed video recording. The TGA has shown multi-step decomposition of both magnesium borides in an argon environment. The maximum oxidation rate of MgB4 in oxygen was observed at a much lower temperature than in the case of MgB2. In the combustion experiments, both magnesium borides burned much faster than submicron boron. Ball milling of the borides further increased their burning rates. It has been concluded that nanoscale magnesium tetraboride is a promising ingredient for fuel-rich propellants owing to its high energy density, efficient oxidation, and rapid combustion.

Molina, Andre [The University of Texas at El Paso]↗

Detecting Layer Height of Smoke Aerosols over Vegetated Land and Water Surfaces via Oxygen Absorption Bands: Hourly Results from EPIC/DSCOVR in Deep Space

We present an algorithm for retrieving aerosol layer height (ALH) and aerosol optical depth (AOD) for smoke over vegetated land and water surfaces from measurements of the Earth Polychromatic Imaging Camera (EPIC) onboard the Deep Space Climate Observatory (DSCOVR). The algorithm uses Earth-reflected radiances in six EPIC bands in the visible and near-infrared and incorporates flexible spectral fitting that accounts for specifics of land and water surface reflectivity. The fitting procedure first determines AOD using EPIC atmospheric window bands (443 nm, 551 nm, 680nm, and 780 nm), then uses oxygen (O2) A and B bands (688 nm and 764 nm) to derive ALH, which represents an optical centroid altitude. ALH retrieval over vegetated surface primarily takes advantage of measurements in the O2B band. We applied the algorithm to EPIC observations of several biomass burning events over the United States and Canada in August 2017. We found that the algorithm can be used to obtain AOD and ALH multiple times daily over water and vegetated land surface. Validation is performed against aerosol extinction profiles detected by the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) and against AOD observed at nine Aerosol Robotic Network (AERONET) sites, showing, on average, an error of 0.58 km and a bias of -0.13 km in retrieved ALH and an error of 0.05 and a bias of 0.03 in retrieved AOD. Additionally, we show that the aerosol height information retrieved by the present algorithm can potentially benefit the retrieval of aerosol properties from EPIC’s ultraviolet (UV) bands.

Cloud–Aerosol Lidar with Orthogonal Polarization (↗

Constant propellant use rendezvous scenario across a launch window for refueling missions

Active rendezvous of an unmanned spacecraft with the Space Transportation System (STS) Shuttle for refueling missions is investigated. The operational constraints facing both the maneuvering spacecraft and the Shuttle during a rendezvous sequence are presented. For example, the user spacecraft must arrive in the generic Shuttle control box at a specified time after Shuttle launch. In addition, the spacecraft must be able to initiate the transfer sequence from any point in its orbit. The standard four-burn rendezvous sequence, consisting of two Hohmann transfers and an intermediate phasing orbit, is presented as a low-energy solution for rendezvous and retrieval missions. However, for refueling missions, the Shuttle must completely refuel the spacecraft and return to Earth with no excess fuel. This additional constraint is not satisfied by the standard four-burn sequence. Therefore, a variation of the four-burn rendezvous, the constant delta-V scenario, was developed to satisfy the added requirement.

Hametz, M. E.↗

Superfluid Helium On-Orbit Transfer (SHOOT) flight demonstration

The Superfluid Helium On-Orbit Transfer (SHOOT) Flight Demonstration was an attached Shuttle payload mounted on a Hitchhiker cross-bay carrier which flew on STS-57 in June of 1993. SHOOT successfully demonstrated the handling and transfer of superfluid helium between two containers, called dewars, in low gravity. SHOOT was a class C payload and for the STS-57 mission was termed a complex secondary payload. The primaries were the retrieval of the EURECA carrier and a collection of modular experiments contained in SPACEHAB. Because the liquid helium was continuously boiling off, SHOOT's activities were scheduled for the first three days of the mission, concurrent with some SPACEHAB experiments, but well before the EURECA retrieval. Control of the SHOOT experiment was highly interactive and originated primarily from the Goddard Payload Operations and Control Center (POCC). Transfer and calibration activities required continuous command windows of up to 50 minutes duration and up to 80 minutes out of each orbit. Occasionally the crew controlled the experiment using the Payload General Support Computer (PGSC) when near-real time control and monitoring was required. SHOOT also placed considerable demands on the orbiter, including a pitch rotation of 3 deg./sec for 15 minutes, and translational burns using both the aft and forward RCS jets to generate accelerations up to 7 milli-g. The basis for these and other requirements are discussed. Interacion with the crew and timing of crew activity during the mission will be detailed. The processing flow of SHOOT at KSC is described with emphasis on the tradeoffs for vertical, as opposed to horizontal, installation in the orbiter. Finally, some lessons learned are presented that are relevant to future cryogenic and Hitchhiker payloads.

Shirron, Peter↗

Human Factors Impact of Different Ramp Controller Scheduling Advisories for ATD-2 Surface Metering in a Human-in-the-Loop Simulation

A human-in-the-loop (HITL) simulation took place in 2019 at NASA Ames Research Center’s Future Flight Central, an airport simulator with a full-scale 360-degree view that showed real-time airport operations at Dallas/Fort Worth International Airport (DFW). The HITL was part of the NASA/FAA Airspace Technology Demonstration 2 (ATD-2) project which involves an on-going field demonstration at Charlotte Douglas International Airport (CLT). In the field demonstration, metering on the airport surface takes place with one of the goals being to reduce runway queue length by holding aircraft at the gate during busy times, thereby reducing fuel burn and CO2 emissions. This goal has been successfully accomplished at CLT by showing Ramp Controllers when to release aircraft at the gate so as to reduce aircraft waiting in the queue. Among the questions that the current simulation at DFW was designed to address were, "Which types of advisories to the Ramp Controllers work best, those that show a ±2 minute window for a release time from the gate, or a ±5 minute window for an arrival time at the spot (where Air Traffic Control takes over) or both?" and "How do these different types of advisories affect Ramp Controller workload and situation awareness?" Another question was, “Does a ramp that is less restrictive than the one at CLT affect compliance with these advisories?”

Bonny K Parke↗

Test System to Study the Ignition of Metals by Polymers in Oxygen

A new test system that uses Laser energy to ignite a polymer promoter has been developed at the NASA White Sands Test Facility. It will facilitate the study of the spread of fire from a burning polymer material to the metal surrounding it. The system can be used to answer questions regarding the effects of configuration on ignition and combustion. The data obtained from this test could also be used to develop mathematical models for analyzing the effects of configuration on ignition and combustion. The system features a 10,000-psi (69-MPa) test chamber with sight glass windows on either end and a 25-watt carbon dioxide Laser for an ignition source. The test system can be used with gaseous oxygen, nitrogen or any mixture of the two gases. To minimize the effect of preheating the metallic, the polymer is ignited with a minimal amount of Laser energy. Igniting the polymer in this fashion also simplifies the thermodynamic analysis of the ignition and propagation reactions. The system is very robust, versatile and straightforward to use. Depending on the test pressure and configuration, the test system operator can perform as many as 20 tests per day. Test results verify that ignition and combustion of the metallic sample is not only dependent on pressure, material type and temperature, but configuration of both the polymer promoter and metallic sample. Both 6061 aluminum and 316 stainless steel 0.25-inch (6.35-mm) diameter rods with a standard 0-ring groove were tested with Buna-N, Silicone, Teflon and Viton 0-rings. The system ignited all four types of 0-rings in oxygen at pressures ranging from ambient to 10,000 psi (69 MPa). However, neither the stainless steel nor the aluminum rods on which the O-rings were mounted ignited in any test conditions. Future testing may be done on the 0.25-inch (6.35-mm) rod and O-ring configuration to evaluate the lack of ignition in these tests. Future configurations may include a plug of polymer in the base of the sample and replicas of fire-damaged components. Furthermore, the test system may be used in the future to analyze the oxidation rate of Laser-heated metals in gaseous oxygen.

Shoffstall, Michael S.↗