SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Electron diffraction patterns and electron micrographs of molybdenum disulfide films sputtered on single-NaCl-crystal and electropolished-aluminum substrates are presented as evidence that crystalline MoS2 films can be sputtered onto various substrates in thicknesses up to 2 microns. Applied to Falex test pins and V-blocks, some of these films exhibited a wear life as long as 65 minutes at 1000 lb jaw load.
Solid film lubricants of radio frequency sputtered molybdenum disulfide (MoS2) were applied to silver, gold, copper, and bronze surfaces that had various pretreatments (mechanical polishing, sputter etching, oxidation, and sulfurization). Optical and electron transmission micrographs and electron diffraction patterns were used to interpret the film formation characteristics and to evaluate the sputtering conditions in regard to the film and substrate compatibility. Sputtered MoS2 films flaked and peeled on silver, copper, and bronze surfaces except when the surfaces had been specially oxidized. The flaking and peeling was a result of sulfide compound formation and the corresponding grain growth of the sulfide film. Sputtered MoS2 films showed no peeling and flaking on gold surfaces regardless of surface pretreatment.
Discussion of the physical and mathematical fundamentals, performance capabilities and potential applications of image deblurring by holography. It is shown that a blurred photograph may be deblurred and a sharpened image extracted from it because the 'blurring' in the original photograph did not irretrievably lose the imaging information, notably in the spatial-frequency regions required for faithful imaging and for high resolution. The principles of optical image deblurring are highly mathematical in nature. One of the most important applications of holographic image deblurring is shown to be the sharpening of electron micrographs of biological specimens beyond the ultimate that can be achieved with even the most powerful instruments available.
The speed of the holographic image deblurring method has recently been further enhanced by a new speed in the realization of the powerful holographic image-deblurring filter. The filter makes it possible to carry out the deblurring, in the optical computer used, in times of the order of one second. The experimental achievements using the holographic image-enhancement method are illustrated with examples ranging from out-of-focus or motion-blurred photographs, including 'amateur' photos recorded on Polaroid film, to the sharpening of the best available electron micrographs of viruses. Images recorded with X-rays, notably from rocket-borne photos of the sun, and out-of-focus photographs from cameras in NASA satellites have been similarly deblurred.
Results of a survey of a variety of environments in the dry valleys of Antarctica, ranging from mountain crests to valley floors. The main purpose of the investigation was the determination of active microbial multiplication in the soil. A series of techniques was employed which permitted the detection of bacterial growth in situ. All evidence points to an active growth of micro-organisms in the Antarctic soil in all locations examined. The measurements were supported by electron micrographs of soil films which showed colonial growth covering soil particles. These findings suggest that Antarctica does not serve as a useful model for the Martian environment in evaluating quarantine standards.
Experimental results on the problem of reducing aerodynamic heating on space shuttle orbiter surfaces are presented. Data include: (1) development of a laboratory flow reactor technique for measuring gamma sub O and gamma sub N on candidate materials at surfaces, T sub w, in the nominal range 1000 to 2000, (2) measurements of gamma sub O and gamma sub N above 1000 K for both the glass coating of a reusable surface insulation material and the siliconized surface of a reinforced pyrolyzed plastic material, (3) measurement of the ablation behavior of the coated RPP material at T sub w is greater than or equal to 2150 K, (4) X-ray photoelectron spectral studies of the chemical constituents on these surfaces before and after dissociated gas exposure, (5) scanning electron micrograph examination of as-received and reacted specimens, and (6) development and exploitation of a method of predicting the aerodynamic heating consquences of these gamma sub O(T sub w) and gamma sub N(T sub w) measurements for critical locations on a radiation cooled orbiter vehicle.
Scanning electron micrographic studies on trapped particles collected shortly after the Leonid meteor shower exhibit surface ablation and spherical formation.
Quantitative efforts to assess the surface properties of lunar fines, particularly water induced porosity are discussed. Data show that: (1) changes induced in lunar fines are not visible in high energy electron micrographs, (2) scanning micrographs show no change in particle size distribution as a result of reaction with water, (3) water induced changes are internal to the particles themselves, (4) normal laboratory atmosphere blocks alteration reaction with water, and (5) surface properties of mature lunar soils appear to be almost independent of chemical composition and mineralogy, but there are some variations in their reactivity toward water.
Results of Auger electron spectroscopy (AES) studies of fracture surfaces in a series of ceramic materials, including Al2O3, MgO, and Si3N4, which were formed using different processing techniques. AES on the fractured surface of a lunar sample is also discussed. Scanning electron micrograph fractography is used to relate the surface chemistry to the failure mode. Combined argon ion sputtering and AES studies demonstrate the local variations in chemistry near the fracture surface. The problems associated with doing AES in insulators are also discussed, and the experimental techniques directed toward solving them are described.
The high-temperature oxidation behavior of thoriated nickel and chromium superalloys is discussed on the basis of scanning electron micrographs and other experimental data. The beneficial effects of dispersed oxide particles are identified as a lower chromium content needed for the formation of external scale, an increased adhesion of scale, and lower growth rates of chromia as compared with those in alloys without dispersed oxide particles.
Graphite-epoxy laminates were thermally cycled to determine the effects of thermal cycles on tensile properties and thermal expansion coefficients of the laminates. Three 12-ply laminate configurations were subjected to up to 5,000 thermal cycles. The cumulative effect of the thermal cycles was determined by destructive inspection (electron micrographs and tensile tests) of samples after progressively larger numbers of cycles. After thermal cycling, the materials' tensile strengths, moduli, and thermal expansion coefficients were significantly lower than for the materials as fabricated. Most of the degradation of properties occurred after only a few cycles. The property degradation was attributed primarily to the progressive development of matrix cracks whose locations depended upon the layup orientation of the laminate.
Petroleum pitch carbon microspheres were prepared by flash heating emulsified pitch and carbonizing the resulting microspheres in an inert atmosphere. Microsphere composites were obtained from a mixture of microspheres and tetraester precursor pyrrone powder. Scanning electron micrographs of the composite showed that it was an aggregate of microspheres bonded together by the pyrrone at the sphere contact points, with voids in and among the microspheres. Physical, thermal, and sorption properties of the composite are described. Composite applications could include use as a honeycomb filler in elevated-temperature load-bearing sandwich boards or in patient-treatment tables for radiation treatment of tumors.
Results are presented for high-temperature (1370, 1430, 1540, 1590 C) slow-strain-rate compression tests on cylindrical specimens of hot-pressed Si3N4 of the HS-130 brand under various compressive loads. The results are presented in terms of number of longitudinal cracks, percent increase in diameter, percent decrease in length, and percent loss in weight. Scanning electron micrographs are presented of cylindrical surfaces of compression specimens tested at 1430 C for 640 MN/sq m and at 1590 C for 220 MN/sq m. As compared to results obtained by other investigators, it appears more likely that the cracks resulting from compressive loading are due to subcritical crack growth caused by circumferential tensile stresses acting across grain boundaries that contain a viscous silicate glass phase.
Current and potential sputtering technology is reviewed as it applies primarily to the deposition of MoS2, though such lubricants as WS2 and PTFE are also considered. It is shown by electron microscopy and surface sensitive analytical techniques that the lubricating properties of sputtered MoS2 films are directly influenced by the sputtering parameters selected (i.e., power density, pressure, sputter etching, dc-biasing, etc.), substrate temperature, chemistry, topography, and environmental conditions during the friction test. Electron micrographs and diffractograms of sputtered MoS2 films clearly show the resultant changes in film morphology which affect film adherence and frictional properties.
A discussion is presented relating the observed pore structures (sizes) to the reaction mechanisms in reaction-bonded silicon nitride (alpha- and beta-Si3N4) on the basis of information available from the literature. While the techniques for reducing the residual macroporosity are quite well-developed for reaction-bonded Si3N4 (RBSN), it is important to be aware of three other orders of magnitude for porosity present in RBSN as a result of the nitriding process itself, and how these types of nitridation-induced porosity can be controlled. For ease of description, these types of nitridation-induced porosity are called micropores, nanopores, and picopores in order of their decreasing size. A scanning electron micrograph is presented, showing nanopores isolated in the unreacted Si and picopores in the alpha-matte Si3N4. The assumption that an alpha-matte growth mechanism is active explains the occurrence of nanopores and their partial filling with alpha-Si3N4, leaving behind very fine-grained alpha-matte and picopores.
A water sampling program was accomplished at Lake Powell, Utah, during June 1975 for correlation to multispectral data obtained with a 500-channel airborne spectroradiometer. Field measurements were taken of percentage of light transmittance, surface temperature, pH and Secchi disk depth. Percentage of light transmittance was also measured in the laboratory for the water samples. Analyses of electron micrographs and suspended sediment concentration data for four water samples located at Hite Bridge, Mile 168, Mile 150 and Bullfrog Bay indicated differences in the composition and concentration of the particulate matter. Airborne spectroradiometer multispectral data were analyzed for the four sampling locations. The results showed that: (1) as the percentage of light transmittance of the water samples decreased, the reflected radiance increased; and (2) as the suspended sediment concentration (mg/l) increased, the reflected radiance increased in the 1-80 mg/l range. In conclusion, valuable qualitative information was obtained on surface turbidity for the Lake Powell water spectra. Also, the reflected radiance measured at a wavelength of 0.58 micron was directly correlated to the suspended sediment concentration.
The cavitation erosion behavior including the initiation, dynamics and mechanism of damage process on perspex and epoxy resin specimens tested in a rotating disk device were discussed with respect to exposure time. The inception of erosion always took place at the location nearest to the center of rotation of the disk. Subsequently, as exposure time increased, erosion initiated at other locations as well. Light optical photographs and scanning electron micrographs clearly indicate that most of the material loss appears to occur form the networks of cracks due to their interaction and pits indicate particle debris. The optical degradation (loss of transmittance) on perspex was observed to be more on the rear side than on the front side.
Gases from Mount St. Helens were collected from the eruption clouds using an airplane during the period April 2 to April 8, 1980, and were analyzed for CO2, H2, CH4, and COS. The results were of similar magnitude to those obtained from magmatic eruptions in Central America. Thus, although the eruptions were evidently largely phreatic, magmatic gases may have played a larger role in these early small eruptions than has generally been believed. Electron micrographs of ash particles collected from the Mount St. Helens eruption clouds showed that the particles were for the most part much larger than those from the Central American eruptions.