Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrostatic effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Electrostatic modulation of the lateral carrier density profile in field effect devices with nonlinear dielectrics

The properties of two-dimensional (2D) electronic systems are often effectively controlled using electrostatic gating. The geometry of such field effect devices influences the effectiveness of the gate and the carrier density profile in the 2D device. Here, in this work, we analyze the gate-induced spatial variations in the lateral carrier density in patterned LaAlO 3 /SrTiO 3 devices. We model the electrostatics of the 2D interface using the Thomas-Fermi approximation and compute the gate-induced charge distribution at the interface. We show that the electric field lines generated by the gate are focused at the edges of the device, causing an increased depletion near its edges. This effect is accentuated in LaAlO 3 /SrTiO 3 due to the large, nonlinear dielectric constant of the substrate, and the large distance between the gate electrode and the interface. We experimentally demonstrate one consequence of this effect by directly imaging current distributions in gated heterostructures, finding that insulating regions nucleate at the edges of the device due to the gate. Our results suggest that device geometry and choice of dielectric materials control the charge distribution in 2D systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Effects of Non-Electrostatic Intermolecular Interactions on the Phase Behavior of pH-Sensitive Polyelectrolyte Complexes

Polyelectrolyte complexes (PECs) offer enormous material tunability and desirable functionalities, and consequently have found broad utility in biomedical and material industries. While poly(acrylic acid) (PAA) and poly( allylamine hydrochloride) (PAH) are a commonly used pairing, various aspects of the phase behavior of PAA-PAH complexes have not been sufficiently quantified. In this work, we present a comprehensive experimental study depicting the binodal phase boundaries for the PAA-PAH complexes prepared under acidic, neutral, and basic conditions using thermogravimetric analysis, turbidimetry, and optical microscopy. Under neutral and basic conditions, phase behaviors of the complexes were largely similar to one another and followed general expectations of PEC phase behavior, except for unusually high resistance to disruption of the complex with added salt. Stable complexes are observed up to 4 M NaCl concentrations. Under acidic conditions, strikingly different phase behaviors of the PAA-PAH complexes were observed. The polymer content in the complex phase increased initially, followed by an expected decrease as salt was added to the complexes. This behavior may result from a combination of associative phase separation of PAA and PAH chains, influenced by electrostatic interactions, and segregative phase separation, which can be ascribed to the influence of a combination of the hydrophobic interactions of the aliphatic polymer backbone and the interpolymer hydrogen bonding of unionized acrylic monomer units. Our systematic investigations over a range of pH detailing these discrepancies in the PAA-PAH phase behavior are expected to clarify the inconsistencies among the reports in the literature and provide the material design strategies for practical use of the PAA-PAH complexes and multilayer assemblies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Effect of Approach Speed and Electrode Geometry on Electrostatic Discharges Off Floating Dielectrics

With the damaging effects of electrostatic discharges (ESDs), it is important to study them within various parameter regimes relevant to real-world scenarios. One such scenario studied here is a floating dielectric with no nearby ground plane with a grounded object approaching at a high rate of speed. One may encounter this scenario when moving objects by hand. Discharge current and radiated fields are captured for discharges drawn from polytetrafluoroethylene (PTFE) and poly methyl methacrylate (PMMA) with approach speeds ranging from 20 to 100 mm/s. Previous studies have shown that at lower speeds in metal-to-metal or metal-to-ground backed dielectric geometries, the peak current and discharge distance decrease with increasing speed. However, in the speed range studied here, an increase in distance and current are observed for increasing speed. Namely, the highest speeds coincide with the highest peak currents and discharge distances of approximately 800 mA and up to 24 mm. Further, with no grounded backing, as opposed to setups in other ESD studies, the electric field between the dielectric and an approaching electrode has a more uniform distribution with highest fields at the electrode, which is elucidated to be the driving factor in the differences revealed in this study. Two spheres of differing diameters and a conical electrode are used to draw discharges off the dielectric surfaces. Captured radiated fields via B-dot sensor, plasma imagery via intesified charge-coupled device (ICCD), and mapping of surface potential reveal that a majority of the energy lost during a discharge goes to gas losses and radiated fields.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Protein Electric Fields Enable Faster and Longer-Lasting Covalent Inhibition of β-Lactamases

The widespread design of covalent drugs has focused on crafting reactive groups of proper electrophilicity and positioning towards targeted amino-acid nucleophiles. In this work, we found that environmental electric fields projected onto a reactive chemical bond, an overlooked design element, play essential roles in the covalent inhibition of TEM-1 beta-lactamase by avibactam. Using the vibrational Stark effect, the magnitudes of the electric fields that are exerted by TEM active sites onto avibactam’s reactive C=O were measured and demonstrate an electrostatic gating effect that promotes bond formation yet relatively suppresses the reverse dissociation. These results suggest new principles of covalent drug design and off-target site prediction. Unlike shape and electrostatic complementary which address binding constants, electrostatic catalysis drives reaction rates, essential for covalent inhibition, and deepens our understanding of chemical reactivity, selectivity, and stability in complex systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Acetonitrile Transition Metal Interfaces from First Principles

Acetonitrile is among the most commonly used nonaqueous solvents in catalysis and electrochemistry. Here, we study its interfaces with multiple facets of the metals Ag, Cu, Pt, and Rh using density functional theory calculations; the structures reported shed new light on experimental observations and underscore the importance of solvent–solvent interactions at high coverage. We investigate the relationship of potential of zero charge (PZC) to metal work function, reporting results in agreement with experimental measurements. We develop a model to explain the effects of solvent chemisorption and orientation on the PZC to within a mean absolute deviation of 0.08–0.12 V for all facets studied. Our electrostatic field dependent phase diagram agrees with spectroscopic observations and sheds new light on electrostatic field effects. This work provides new insight into experimental observations on acetonitrile metal interfaces and provides guidance for future studies of acetonitrile and other nonaqueous solvent interfaces with transition metals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Controlling protein adsorption modes electrostatically

Protein adsorption on surfaces is ubiquitous in biology and in biotechnology. There are various forces required for controlling protein adsorption. Here, we introduce an explicit ion coarse-grained molecular dynamics simulation approach for studying the effects of electrostatics on protein adsorption, and 2D protein assembly on charged surfaces. Our model accounts for the spatial distribution of protein charges. We use catalase as our model protein. We find that the preferential adsorption mode of proteins at low protein concentration on a charged surface is “standing up”. When the protein concentration in a solution increases to reach a critical density on the surface, the adsorption mode switches from “standing up” to a mixed state “flat on” and “standing up”, which increases the lateral correlations among the adsorbed proteins. As such, the changes in the adsorption mode arise from the protein adsorption that cancel the surface charge and the protein–protein repulsion. This correlated surface structure melts as the salt concentration increases because the charged surface is cancelled by the salt ions and the proteins de-adsorb. For the case of strongly charged surfaces the “standing up” conformation remains more favorable even at high protein adsorption at low salt concentrations since in that conformation the surface charge is cancelled more effectively, generating an even more laterally correlated structure. We elucidate the effects of parameters such as surface charge density, salt concentration, and protein charges on the different adsorption modes and the structure and organization of proteins on the charged surfaces. Finally, this study provides a guide for controlling protein assembly on surfaces.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Long-Term Aging in Miscible Polymer Nanocomposites

Here we find that the initial, solvent-cast state of nanoparticles (NPs) in a polymer matrix temporally evolves during thermal annealing such that, at steady state, NPs maximize their distance from each other subject to mass balance constraints. The observed timescales for this unexpected structural reorganization, as probed by small-angle X-ray scattering, are temperature-dependent and can be prohibitively large, especially at temperatures around and below 1.2Tg. X-ray photon correlation spectroscopy measurements during reorganization reveal that the collective NP dynamics slow down with annealing at constant temperature; this is accompanied by changes in the low-frequency regime in macroscopic viscoelastic measurements in equilibrated materials. By ruling out other potential sources for these effects (i.e., electrostatic interactions, adsorbed layers), we attribute these results to a long-ranged repulsive force between the NPs caused by fluctuations in the polymer phase, i.e., the "anti-Casimir" effect proposed by Obhukhov and Semenov [Long-range interactions in polymer melts: The anti-Casimir effect. Phys Rev Lett 2005, 95 (3), 038305]. Thus, our results highlight the important role of long-term, slow NP reorganization on the structure and, subsequently, the properties of polymer nanocomposites (PNCs), even in the case of nominally miscible polymer nanoparticle hybrids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Electromechanics of lipid-modulated gating of potassium channels

Experimental studies reveal that the anionic lipid phosphatidic acid (POPA), non-phospholipid cholesterol, and cationic lipid DOTAP inhibit the gating of voltage-sensitive potassium (Kv) channels. In this work, we develop a continuum electromechanical model to investigate the interaction of these lipids with the ion channel. Our model suggests that: (i) POPA lipids may restrict the vertical motion of the voltage-sensor domain through direct electrostatic interactions; (ii) cholesterol may oppose the radial motion of the pore domain of the channel by increasing the mechanical rigidity of the membrane; and (iii) DOTAP can reduce the effect of electrostatic forces by regulating the dielectric constant at the channel–lipid interface. The electromechanical model predictions for the three lipid types match well with the experimental observations and provide mechanistic insights into lipid-dependent gating of Kv channels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Thermodynamic Model and Initial Experimental Investigation of Air Dehumidification through Electrically Charged Vapor Capturing Electrostatic Droplets

The removal of water vapor from the air to reduce relative humidity is a well known indoor environmental comfort requirement. Common dehumidification approaches require a substantial amount of energy and usually involve the cooling of atmospheric humid air below its dew point or the use of absorbent/adsorbent materials to extract water vapor out of the air. More recently, researchers investigated the effect of electrostatic forces for enhancing water vapor condensation with the goal to reduce the energy consumption associated with dehumidification. However, the studies are limited, and there is a lack of correlations that can predict the dehumidification rate. In this thesis, a broad theoretical investigation to study the electrostatically enhanced condensation processes was carried out. These processes consist of the use of highly charged particles, preferably highly charged water droplets to attract polar water vapor molecules to their surfaces and promote condensation, a phenomenon known as dielectrophoresis. The electrical charge promotes the reduction of the vapor pressure on the droplets' surface with respect to the saturated pressure predicted by the Kelvin equation on curved surfaces and, consequently, the equilibrium between evaporation and condensation is shifted towards condensation. This investigation resulted in the development of a thermodynamics model, which was able to predict an effective size range of the charged droplets for optimal dehumidification, under ideal conditions. The range resulted in about 2 to 4 m in diameter, while the electrical charge was kept to the maximum limit predicted by the Rayleigh model. A sensitivity analysis on the variation of the size and the charge of the charged droplets was also performed. In terms of dehumidification rates, when six electrospray heads, i.e. the maximum number of heads tested in the experimental campaign, were considered, the model predicted very limited rates, way lower than the target of this research, i.e. a dehumidification rate in terms of relative humidity of 5 % with an air flow rate of 5 cfm. While ways to increase this rate existed, their implementation proved difficult for this initial investigation. According to the requirements predicted by the model, the use of electrosprays appeared the most suitable solution for the production of small but highly charged droplets. The electrospray features and operational modes were studied in detail and an electrospray assembly was designed to be tested in this initial experimental investigation. For this initial investigation, an experimental system was designed and built to validate the thermodynamics model and with the goal to achieve a dehumidification rate of 5 % in terms of relative humidity with an air flow rate of 5 cfm. The experimental system consisted of a wind tunnel test apparatus, dew point sensors, thermocouples for temperature measurements, pressure sensors and other devices. The experimental system was equipped with a computerized data acquisition and storage system. The system was suitable to evaluate the air water content differential before and after the test section where the electrospray heads were installed. The air water content differential was evaluated in terms of the ∆ω/ω_1 ratio, to eliminate the dependence on the dry bulb temperature along the test apparatus. This work presented initial experimental data for electrostatically enhanced dehumidification processes. Working parameters, such as air and water flow rates, high voltage potentials and polarity, deionized water types with different electrical conductivity, were varied to find the best combination for an improved dehumidification. With the set up used and the conditions considered, it was never possible to achieve a 5 % dehumidification rate with 5 cfm. In general, the dehumidification rate was always limited and lower than 1 % for all the air flow rates considered and mainly within the uncertainty of the dew point sensors. These results confirmed the already limited predictions of the thermodynamics model, for ideal conditions and the interesting and promising results obtained in some experimental investigations available in the open literature were not achievable in this thesis. The more probable reasons were the higher air flow rates considered and the complete absence of the use of cooling power, which was mainly implemented to facilitate the vapor condensation.

Morcelli, Stefano↗
DOE OSTI2021

Analysis of Electro-static Assisted Air Dehumidification

The removal of water vapor from the air to reduce relative humidity is a well-known indoor environmental comfort requirement. Common dehumidification approaches require a substantial amount of energy and usually involve the cooling of atmospheric humid air below its dew point or the use of absorbent/adsorbent materials to extract water vapor out of the air. More recently, researchers investigated the effect of electrostatic forces for enhancing water vapor condensation. However, the studies are limited, and there is a lack of correlations that can predict the dehumidification rate. Also, the findings from the literature focused mainly on small flow rates on the order of one to two cfm. Electrically-enhanced condensation consists of the use of highly charged particles, preferably highly charged water droplets, that attract polar water vapor molecules to their surfaces and promote condensation, a phenomenon known as dielectrophoresis. An effect of the electric charge is the reduction of the vapor pressure on the droplets' surface with respect to the saturated pressure predicted by the Kelvin equation. Consequently, the equilibrium between evaporation and condensation is shifted towards condensation. Following the application of the modified Kelvin-Thomson theory, we developed a preliminary physics-based model to predict an effective size range of the charged droplets for optimal dehumidification. The range resulted in about 2 to 4 μm in diameter, under few simplifying assumptions. The effect of the size and the charge of the electrosprayed droplets on the overall dehumidification rate was briefly discussed. The use of electrosprays to produce small but highly charged droplets was broadly discussed in this paper. The cone-jet mode was identified as the most suitable electrospray operational mode, and it generated droplets of small size and high electrical charge. The cone-jet stability was also analyzed in detail. The preliminary data of the present work and the model results indicated that several electrospray heads were required to achieve a 5% dehumidification rate for airflow rates of about 5 cfm.

Morcelli, Stefano↗
DOE OSTI2021

Analysis of New Data of Electro-static Assisted Air Dehumidification Processes

The removal of water vapor from the air to reduce relative humidity is a well-known indoor environmental comfort requirement. Common dehumidification approaches require a substantial amount of energy and usually involve the cooling of atmospheric humid air below its dew point or the use of absorbent/adsorbent materials to extract water vapor out of the air. More recently, researchers investigated the effect of electrostatic forces for enhancing water vapor condensation. However, the studies are limited, and there is a lack of correlations that can predict the dehumidification rate. Also, the findings from the literature focused mainly on small flow rates on the order of one to two cfm. Electrically-enhanced condensation consists of the use of highly charged particles, preferably highly charged water droplets, that attract polar water vapor molecules to their surfaces and promote condensation, a phenomenon known as dielectrophoresis. An effect of the electric charge is the reduction of the vapor pressure on the droplets' surface with respect to the saturated pressure predicted by the Kelvin equation. Consequently, the equilibrium between evaporation and condensation is shifted towards condensation. Following the application of the modified Kelvin-Thomson theory, we developed a preliminary physics-based model to predict an effective size range of the charged droplets for optimal dehumidification. The range resulted in about 2 to 4 m in diameter, under few simplifying assumptions. The effect of the size and the charge of the electrosprayed droplets on the overall dehumidification rate was briefly discussed. The use of electrosprays to produce small but highly charged droplets was broadly discussed in this paper. The cone-jet mode was identified as the most suitable electrospray operational mode, and it generated droplets of small size and high electrical charge. The cone-jet stability was also analyzed in detail. The preliminary data of the present work and the model results indicated that several electrospray heads were required to achieve a 5% dehumidification rate for airflow rates of about 5 cfm.

Morcelli, Stefano↗
DOE OSTI2022

First direct observations of gear-changing in a collider

In this work we perform the first demonstration of gear-changing in a real world collider. Gear-changing refers to a collision scheme where each ring of a collider stores a different harmonic number of bunches. These bunches are kept synchronized using different velocities. Such a system has been theorized, but has now been demonstrated using the Double ElectroStatic Ion Ring ExpEriment (DESIREE) in Stockholm Sweden. The experiment was able to demonstrate a gear-changing system, with both four on three bunches and five on four bunches. We determined a measurable parameter that shows a gear-changing system out to $37500$ turns of the slow beam (1 second). We were also able to detect a measurable longitudinal beam-beam interaction. We developed insights into how to control this type of system, opening up new possibilities, and showing that DESIREE can be used for gear-changing research.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Hybrid Quantum Mechanical, Molecular Mechanical, and Machine Learning Potential for Computing Aqueous-Phase Adsorption Free Energies on Metal Surfaces

Performing reliable computer simulations of elementary processes occurring at metal–water interfaces is pivotal for novel catalyst design in sustainable energy applications. Computational catalyst design hinges on the ability to reliably and efficiently compute the potential energy surface (PES) of the system. Here, due to the large system sizes needed for studying processes at liquid water–metal interfaces, these systems can currently not be described using density functional theory (DFT). In this work, we used a hybrid quantum mechanical, molecular mechanical, and machine learning potential for studying the adsorption behavior of phenol, atomic hydrogen, 2-butanol, and 2-butanone on the (0001) facet of Ru under reducing conditions when Ru is not oxidized. Specifically, we describe the adsorbate and the surrounding metal atoms at the DFT level of theory. Here, we also considered the electrostatic field effect of the water molecules on adsorbate–metal interactions. Next, for the water–water and water–adsorbate interactions, we used established classical force fields. Finally, for the water–Ru surface interaction, for which no reliable force fields have been published, we used Behler–Parrinello high-dimensional neural network potentials (HDNNPs). Employing this setup, we used our explicit solvation for metal surface (eSMS) approach to compute the aqueous-phase effect on the low-coverage adsorption of selected molecules and atoms on the (0001) facet of Ru. In agreement with previous experimental and computational studies of oxygenated molecules over transition metal facets, we found that liquid water destabilizes the tested adsorbates on Ru(0001). Interestingly, our findings indicate that adsorbates on Ru are less affected by the presence of an aqueous phase than on other transition metals (e.g., Pt), highlighting the necessity of experimental investigations of Ru-based catalytic systems in liquid water.

Adsorption↗
DOE OSTI2024

Modulation of Electrostatic Potential in 2D Crystal Engineered by an Array of Alternating Polar Molecules

The moiré potential in rotationally misfit two-dimensional (2D) heterostructures has been used to build artificial exciton and electron lattices, which have become platforms for realizing exotic electronic phases. Here, we demonstrate a different approach to create a superlattice potential in 2D crystals by using the near field of an array of polar molecules. Here, a bilayer of titanyl phthalocyanine (TiOPc), consisting of alternating out-of-plane dipoles, is deposited on monolayer MoS 2 . Time-resolved two-photon photoemission spectroscopy reveals a pair of interlayer exciton states with an energy difference of ~0.1 eV, which is consistent with the electrostatic potential modulation induced by the TiOPc bilayer as determined by density functional theory calculations. Because the symmetry and the period of this potential superlattice can be changed readily by using molecules of different shapes and sizes, molecule/2D heterostructures can be promising platforms for designing artificial exciton and electron lattices.

2D heterostructures↗
DOE OSTI2020

Phase diagrams of single-layer two-dimensional transition metal dichalcogenides: Landau theory

We report single layer (SL) two-dimensional transition metal dichalcogenides (TMDs), such as MoS 2 , ReS 2 , WSe 2 , and MoTe 2 have now become the focus of intensive fundamental and applied research due to their intriguing and tunable physical properties. These materials exhibit a broad range of structural phases that can be induced via elastic strain, chemical doping, and electrostatic field effect. These transformations, in turn, can open and close the band gap of SL-TMDs, leading to metal-insulator transitions, and lead to emergence of more complex quantum phenomena. These considerations necessitate detailed understanding of the mesoscopic mechanisms of these structural phase transitions. Here we develop a Landau-type thermodynamic description of SL-TMDs on a sample of the SL-(MoS 2 ) 1-x -(ReS 2 ) x system and analyze the free energy surfaces, phase diagrams, and order parameter behavior. Our results predict the existence of multiple structural phases with two-, six- and 12-fold degenerated energy minima for in-plane and out-of-plane order parameters. This analysis suggests that out-of-plane ferroelectricity can exist in many of these phases, with the switchable polarization being proportional to the out-of-plane order parameter. We further predict that the domain walls in SL-(MoS 2 ) 1-x -(ReS 2 ) x should become conductive above a certain strain threshold.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Density functionals combined with van der Waals corrections for graphene adsorbed on layered materials

Standard density functionals like Perdew-Burke-Ernzerhof (PBE) or Strongly Constrained and Appropriately Normed (SCAN) need a correction to account for long-range van der Waals (vdW) interaction. The damped Zaremba-Kohn model (dZK) starts from a formula for the vdW interaction of a distant atom with a solid surface, both with known dielectric properties, damps this formula at short range, and then treats an adsorbed molecule or atomic layer as a collection of renormalized atoms. Here, we extend this model to graphene adsorbed on semiconducting layered materials [bulk graphite and hBN, and multilayer transition metal dichalcogenides (TMD)] by including the C 4 asymptotic term and multiple electrostatic image effects due to the two surfaces of the substrate slabs in the vdW calculations. The resulting SCAN-vdW-dZK and PBE-vdW-dZK give approximately the same results for the systems considered here, in agreement with available reference values. The predicted binding energies are roughly 25% lower than those from SCAN+rVV10 (revised Vydrov and Van Voorhis 2010), and ~15% lower than those from PBE+rVV10. Since SCAN+rVV10 usually overbinds, the predicted binding energies by SCAN-vdW-dZK and PBE-vdW-dZK are expected to be closer to the true values. The predicted equilibrium binding distances from SCAN-vdW-dZK and PBE-vdW-dZK are slightly larger (~ 0.1 Å) than those from SCAN+rVV10, and close to those from SCAN. The binding energy depends upon the number of substrate layers more strongly in vdW-dZK than in rVV10. The C 4 -term contributions can be 40% of the total vdW interactions, and the C 5 term contributes about 10%. The effects of images and the back surfaces of slabs can contribute about 4–10%. The vdW interaction energy power laws from the vdW-dZK model for graphene adsorbed on multilayer MoS 2 show slowly varying decay to the pairwise exponent –4 with increasing separation $\textit{D}$, very similar to those obtained from the random-phase approximation and renormalization group approaches by Ambrosetti et al. Both the PBE-vdW-dZK and SCAN-vdW-dZK give a greater increase in interlayer binding energy when the TMD substrate changes from monolayer to four-layer for the graphene/TMD adsorption systems. This is consistent with the relevant electron-energy-loss spectroscopy experimental results showing increased dielectric response from the substrate with increasing substrate layer number.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Electrostatic Barriers to Nanoparticle Accessibility of a Porous Matrix

Translocation from one cavity to another through a narrow constriction (i.e., a “hole”) represents the fundamental elementary process underlying hindered mass transport of nanoparticles and macromolecules within many natural and synthetic porous materials, including intracellular environments. This process is complex and may be influenced by long-range (e.g., electrostatic) particle–wall interactions, transient adsorption/desorption, surface diffusion, and hydrodynamic effects. In this study, we used a three-dimensional (3D) tracking method to explicitly visualize the process of nanoparticle diffusion within periodic porous nanostructures, where electrostatic interactions were mediated via ionic strength. The effects of electrostatic interactions on nanoparticle transport were surprisingly large. For example, an increase in the Debye length of only a few nanometers (in a material with a hole diameter of ~100 nm) increased the mean cavity escape time 3-fold. A combination of computational and experimental analyses indicated that this hindered cavity escape was due to an electrostatic energy barrier in the region of the hole, which was quantitatively explained using DLVO theory. These findings explicitly demonstrate that the cavity escape process was barrier-limited and dominated by electrostatic effects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Nonvolatile Memristive Effect in Few-Layer CrI 3 Driven by Electrostatic Gating

The potential of memristive devices for applications in nonvolatile memory and neuromorphic computing has sparked considerable interest, particularly in exploring memristive effects in two-dimensional (2D) magnetic materials. However, the progress in developing nonvolatile, magnetic field-free memristive devices using 2D magnets has been limited. In this work, we report an electrostatic-gating-induced nonvolatile memristive effect in CrI 3 -based tunnel junctions. The few-layer CrI 3 -based tunnel junction manifests notable hysteresis in its tunneling resistance as a function of gate voltage. We further engineered a nonvolatile memristor using the CrI 3 tunneling junction with low writing power and at zero magnetic field. We show that the hysteretic transport observed is not a result of trivial effects or inherent magnetic properties of CrI 3 . We propose a potential association between the memristive effect and the newly predicted ferroelectricity in CrI 3 via gating-induced Jahn–Teller distortion. Furthermore, our work illuminates the potential of 2D magnets in developing next-generation advanced computing technologies.

2D magnet↗