Search NASA⌕ Search

SEARCH · Search NASA

Results for “manufacturing rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Thermal Response of Thermoplastic Composite Tape During In-situ Consolidation Automated Fiber Placement Using a Laser Heat Source

Composite materials have tremendous potential in the design and manufacture of commercial aircraft due to their high strength-to-weight and stiffness-to-weight properties. However, the use of composite materials is currently limited by high cost and long manufacturing time. The National Aeronautics and Space Administration (NASA) initiated the Hi-rate Composite Aircraft Manufacturing (HiCAM) project to investigate promising composite processing technologies with a goal of vastly improving composite commercial aircraft manufacturing rate (4-6x faster than current production rates). Laser assisted automated fiber placement (AFP) of thermoplastics is a key technology that could increase speed of composite manufacturing, but the technology has not been fully developed. In-situ consolidation AFP of thermoplastics (ICAT) could reduce time and cost even further by eliminating the time and equipment required for post-consolidation. In this work, the thermal response of laser heated ICAT was investigated using forward looking infrared (FLIR) and embedded thermocouples (TCs) to better understand fusion between layers (autohesion). Detailed explanation of the algorithm to combine FLIR and TC data will be presented. In addition, the effect of robot speed on time above melting temperature was quantified.

Laser Heating↗
NASA NTRS1974

Room temperature stretch forming of scale space shuttle external tank dome gores. Volume 1: Technical

An account of activities and data gathered in the Room Temperature Stretch Forming of One-third Scale External Tank Bulkhead Gores for space shuttle study, and a tooling design and production cost study are reported. The following study phases are described: (1) the stretch forming of three approximately one-third scale external tank dome gores from single sheets of 2219-T37 aluminum alloy; (2) the designing of a full scale production die, including a determination of tooling requirements; and (3) the determination of cost per gore at the required production rates, including manufacturing, packaging, and shipping.

Blunck, R. D.↗
NASA NTRS1989

The impact of solar cell technology on planar solar array performance

The results of a study into the potential impact of advanced solar cell technologies on the characteristics (weight, cost, area) of typical planar solar arrays designed for low, medium and geosynchronous altitude earth orbits are discussed. The study considered planar solar array substrate designs of lightweight, rigid-panel graphite epoxy and ultra-lightweight Kapton. The study proposed to answer the following questions: Do improved cell characteristics translate into array-level weight, size and cost improvements; What is the relative importance of cell efficiency, weight and cost with respect to array-level performance; How does mission orbital environment affect array-level performance. Comparisons were made at the array level including all mechanisms, hinges, booms, and harnesses. Array designs were sized to provide 5kW of array power (not spacecraft bus power, which is system dependent but can be scaled from given values). The study used important grass roots issues such as use of the GaAs radiation damage coefficients as determined by Anspaugh. Detailed costing was prepared, including cell and cover costs, and manufacturing attrition rates for the various cell types.

Mills, Michael W.↗
NASA NTRS2017

Observation of Single-Event Burnout During Inductive Switching

1A power MOSFET demonstrated destructive Single-Event Effect (SEE) during ion irradiation in a switching circuit. Further investigation showed that the inductive load causing a spike in the drain-to-source voltage (VDS) that exceeded the manufacturer’s rating for several nanoseconds was enough to allow SEB. These results indicate that SEB may occur in a very short window and flyback is critical for disciplined power supply design.

Menke, Rob↗
NASA NTRS2022

NASA Analysis of Alternatives Study for Icing Research

In 2020, NASA’s Aeronautics Research Mission Directorate commissioned a study of the icing research area to provide a broad and comprehensive assessment of priority needs for NASA and enduring needs for the aviation community. Priority needs were those that supported four key focus areas for NASA Aeronautics—Transonic Truss-Braced Wing, Electrified Aircraft Propulsion, Small-Core Turbine Engine, and High-Rate Composite Manufacturing—as well as other priority areas, such as Advanced Air Mobility, Certification by Analysis, and Commercial Supersonic Technology. Enduring needs were the additional long-term capabilities and expertise identified by the aviation community as being critical for NASA to provide. This study is called an Analysis of Alternatives (AoA) because a large number of icing research needs were identified and analyzed to determine the highest priorities for NASA key focus areas and those that will endure into the future. This report offers a detailed description and results of the AoA study for icing research.

Aircraft Icing, Aircraft Icing, Rotorcraft Icing, ↗
NASA NTRSDate not supplied

Stiffener Jumping for Unitized Stitched Composite Preform Manufacturing

A single-sided stitching head is used to assemble unitized three-dimensional preforms using the NASA Langley Research Center (LaRC) Integrated Structural Assembly of Advanced Composites (ISAAC) robotic manufacturing system. Typically, assembly of a preform includes a “skin” that is stiffened by stiffener elements stitched to the skin. The single-sided stitching head has two needles that pass through the preform from the same side to form the stitch, typically from the smooth outer surface so the needles penetrate through the preform towards the stiffener side. The single-sided head cannot stitch across stiffening elements (e.g., stringer, frame, integral cap, etc.) because the needles would penetrate into the stiffener web, which would not allow the stitch form because the thread movement would be impeded. As a result, stitching seams cannot cross stiffening elements, and therefore are very short and must remain in the skin/flange connections within the space between the stiffening element webs. Each short segment requires a stop and cut process that takes a significant amount of time. A stiffener jumping stitching method was developed that eliminates the need to cut and restart seams when encountering a stiffener, thus providing a long, continuous seam with a significant reduction in stitching time by eliminating cutting operations and associated excess thread end trimming. This stiffener jumping process places what could be considered a very long stitch that bridges the stiffener to connect the end of one segment of the seam with the beginning of the next segment of the seam to provide a longer continuous seam. As a result, all intermediate thread cuts that would be done at the end of each individual segment of the seam are eliminated, with only a single cut at the end of the seam. The process and programming requirements for carrying out the stiffener jumping stitching approach are presented in this paper. Using the presented stiffener jumping approach to produce the long continuous seams, the stitching time for a representative commercial transport unitized stiffened wing cover panel can possibly be reduced by at least 25 percent.

stitched↗
NASA NTRSDate not supplied

Impact of Thermoplastic Composites: Testing and Modeling

Thermoplastic Composites (TPCs) are being increasingly considered for aerospace applications given their faster manufacturing cycles and lower cost. The NASA High-Rate Composite Aircraft Manufacturing (HiCAM) project aims to evaluate and mature thermoplastic manufacturing technologies to achieve a 4X – 6X increase in the production rate of Next Generation Single Aisle (NGSA) commercial aircraft. Within the purview of the NASA HiCAM project, this work investigates the response of thermoplastic composites under High Energy Dynamic Impact (HEDI) conditions. HEDI tests were conducted on panels fabricated with a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK) material system. A blunt metal projectile was chosen as the impactor which impacted the T700/LMPAEK panels over a range of impact velocities imparted by a gas gun test setup. As expected, lower velocity impacts caused the projectile to rebound, whereas higher velocity impacts resulted in the projectile penetrating the test panels. For the test cases in which the projectile rebounded, the predominant damage modes recorded with Ultrasonic (UT) scans included interlaminar delaminations which exhibited a “rotating fan” like structure when viewed in the through-thickness direction. Additionally, the dynamic deflection of the center point of the back face of the test panels and the velocity of the projectile was also measured during the test. Finite element models were developed to model a test case in which the projectile rebounded. These models were developed using LS-DYNA® wherein the primary objective was to evaluate the ability of the material model MAT299 to capture the dynamic response and damage modes in the T700/LMPAEK test panels. MAT299 is a Deformation Gradient Decomposition (DGD) based Continuum Damage Mechanics (CDM) material model. The interlaminar delaminations were modeled using the cohesive contact formulation available within LS-DYNA, wherein the mixed-mode fracture is captured via the Benzegaggh-Kenane (B-K) mode-dependent fracture energy interpolation law. The above-mentioned modeling methods have mostly been applied to thermoset composites and adapting them to TPCs involves addressing challenges associated with appropriately representing material behavior. Therefore, the proposed paper would discuss the systematic approach taken to adapt thermoset composites modeling practices for applications to TPCs, while appropriately addressing material behavior. The proposed paper would show that the predicted back face center point deflection correlated reasonably well with experimental data and the peak deflection was predicted to be within 5% of the experimental measurements. The projectile rebound velocity, while predicted to be higher than the experimental measurement, was within reasonable bounds. Additionally, it will be shown that the predicted delamination shapes were in reasonable agreement with experimental data.

Composite Materials↗
NASA NTRSDate not supplied

Thermal Modelling of the in-Situ Consolidation of Automated Fiber Placement of Thermoplastic Composites

NASA is developing carbon fiber reinforced thermoplastic composites processing methods under the Hi-rate Composites Aircraft Manufacturing (HiCAM) project. The in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process has high potential to increase manufacturing throughput and lower costs as it combines the repeatability and fast lay down rates of AFP with the thermoformability of thermoplastic materials to achieve part consolidation out of the autoclave. Physics-based process models are employed in the ICAT process development to understand, fundamentally, the thermal response of the carbon fiber (CF)/polyaryletherketone (PAEK) material during the rapid heating and cooling associated with laser-assisted AFP. A one-dimensional (1-D) closed-form model was developed capable of predicting the temperature profile through-the-thickness of the tape material. In addition, a two-dimensional (2-D) model was developed to predict the heat transfer through-the-thickness and in the laydown x-direction of the AFP head motion. The solution of the Fourier heat-transfer equations in the 2-D model is approximated using the explicit finite difference numerical method. The temperature profile during placement of PAEK slit-tape materials at various laser target temperatures and placement speeds were measured during ICAT process development trials at Electroimpact®, Inc. †† and the resulting experimental data is compared with the predictions of the 1-D and 2-D models.

Thermoplastics↗
NASA NTRSDate not supplied

Thermal Modelling of the In-Situ Consolidation of Automated Fiber Placement Of Thermoplastic Composites

NASA is developing carbon fiber reinforced thermoplastic composites processing methods under the Hi-rate Composites Aircraft Manufacturing (HiCAM) project. The in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process has high potential to increase manufacturing throughput and lower costs as it combines the repeatability and fast lay down rates of AFP with the thermoformability of thermoplastic materials to achieve part consolidation out of the autoclave. Physics-based process models are employed in the ICAT process development to understand, fundamentally, the thermal response of the carbon fiber (CF)/polyaryletherketone (PAEK) material during the rapid heating and cooling associated with laser-assisted AFP. A one-dimensional (1-D) closed-form model was developed capable of predicting the temperature profile through-the-thickness of the tape material. In addition, a two-dimensional (2-D) model was developed to predict the heat transfer through-the-thickness and in the laydown x-direction of the AFP head motion. The solution of the Fourier heat-transfer equations in the 2-D model is approximated using the explicit finite difference numerical method. The temperature profile during placement of PAEK slit-tape materials at various laser target temperatures and placement speeds were measured during ICAT process development trials at Electroimpact®, Inc. †† and the resulting experimental data is compared with the predictions of the 1-D and 2-D models.

Christopher J. Stelter↗
NASA NTRS1995

Making Composite-Material Parts At Moderate To High Rates

Composite-material (matrix/fiber) structural components manufactured at moderate to high rates in production-line-style processes, according to proposal. In method, production lines largely automated and takes advantage of fact matrix resins cured by electron beams in addition to heat. Net result reductions in production times and costs.

Farley, Gary L.↗