Search NASA⌕ Search

SEARCH · Search NASA

Results for “o Wing aerodynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

Aerodynamic Forces and Moments on a Large Ogive-Cylinder Store at Various Locations Below the Fuselage Center Line of a Swept-Wing Bomber Configuration at a Mach Number of 1.61

A supersonic wind-tunnel investigation on store interference has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 1.61. Forces and moments were measured on a large ogive-cylinder store in the presence of a 45 deg swept-wing-fuselage bomber configuration for a number of store locations below the fuselage center line. Results of the investigation show that large variations of store lift, drag, and pitch occur with changes in store or airplane angle of attack, store vertical location, and store horizontal location. The variation of the store forces and moments with respect to the chordwise location of the wing plan form indicates that the wing is a large factor in producing the interference loads on the store. Comparison of data for underfuselage and underwing store locations at an angle of attack of 0 deg showed maximum store drag interferences of similar magnitudes, but showed considerably smaller maximum interference on store lift an pitching moments for underfuselage store locations.

SUPERSONIC FLIGHT↗
NASA NTRS1981

Aerodynamic tests and analysis of a turbojet-boosted launch vehicle concept (spacejet) over a Mach number range of 1.50 to 2.86

Results from analytical and experimental studies of the aerodynamic characteristics of a turbojet-boosted launch vehicle concept through a Mach number range of 1.50 to 2.86 are presented. The vehicle consists of a winged orbiter utilizing an area-ruled axisymmetric body and two winged turbojet boosters mounted underneath the orbiter wing. Drag characteristics near zero lift were of prime interest. Force measurements and flow visualization techniques were employed. Estimates from wave drag theory, supersonic lifting surface theory, and impact theory are compared with data and indicate the ability of these theories to adequately predict the aerodynamic characteristics of the vehicle. Despite the existence of multiple wings and bodies in close proximity to each other, no large scale effects of boundary layer separation on drag or lift could be discerned. Total drag levels were, however, sensitive to booster locations.

Riebe, G. D.↗
NASA NTRS1976

Subsonic loads on wings having sharp leading edges and tips

A vortex-lattice method for predicting the aerodynamics of wings having separation at the sharp edges in incompressible flows is extended to compressible subsonic flows using a modified Prandtl-Glauert transformation. Numerical results showing the effect of freestream Mach number on the aerodynamic coefficients are compared with available experimental data for several planforms. It is shown that the proposed method is suitable for predicting the aerodynamic loads on low-aspect wings at moderate angles of attack for high subsonic freestream Mach number. The method is limited to angles of attack up to 12 deg for high subsonic freestream Mach number and to angles of attack up to 20 deg for Mach number not exceeding 0.5.

Kandil, O. A.↗
NASA NTRS1986

Measurement of leading edge vortices from a delta wing using a three component laser velocimeter

An investigation of the flow field above a 75-deg swept delta wing at a 20.5-deg angle of attack is described. The experiment was performed in the NASA Langley Basic Aerodynamic Research Tunnel (BART) using an orthogonal three-component laser velocimeter. Preliminary laser velocimeter results show velocity vectors in the cross flow plane at x/c = 0.5, revealing the formation of the primary and secondary vortices over the upper surface of the wing.

Meyers, James F.↗
NASA NTRS1991

On a global aerodynamic optimization of a civil transport aircraft

An aerodynamic optimization procedure developed to minimize the drag to lift ratio of an aircraft configuration: wing - body - tail, in accordance with engineering restrictions, is described. An algorithm developed to search a hypersurface with 18 dimensions, which define an aircraft configuration, is discussed. The results, when considered from the aerodynamic point of view, indicate the optimal configuration is one that combines a lifting fuselage with a canard.

Savu, G.↗
NASA NTRS1987

Analysis of a fixed-pitch X-wing rotor employing lower surface blowing

Lower surface blowing (LSB) is investigated as an alternative to the variable blade pitch requirement for the X-wing Circulation Control (CC) rotor concept. Addition trailing edge blowing slots on the lower surfaces of CC airfoils provide a bidirectional lift capability that effectively doubles the control range. The operational requirements of this rotor system are detailed and compared to the projected performance attributes of LSB airfoils. Analysis shows that, aerodynamically, LSB supplies a fixed pitch rotor system with the equivalent lift efficiency and rotor control of present CC rotor designs that employ variable blade pitch. Aerodynamic demands of bidirectional lift production are predicted to be within the capabilities of current CC airfoil design methodology. Emphasis in this analysis is given to the high speed rotary wing flight regime unique to stoppable rotor aircraft. The impact of a fixed pitch restriction in hover and low speed flight is briefly discussed.

Schwartz, Alan W.↗
NASA NTRS1980

Hybrid vortex method for lifting surfaces with free-vortex flow

A Nonlinear Hybrid Vortex method (NHV-method) has been developed for predicting the aerodynamic characteristics of wings exhibiting leading- and side-edge separations. This method alleviates the drawbacks of the Nonlinear Discrete Vortex method (NDV-method, also known as the multiple line vortex method.) The NHV-method combines continuous-vorticity and vortex-line representations of the wing and its separated free shear layers. Continuous vorticity is used in the near-field calculations, while discrete vortex-lines are used in the far-field calculations. The wing and its free shear layers are divided into quadrilateral vortex panels having second-order vorticity distributions. The aerodynamic boundary conditions and continuity of the vorticity distributions are satisfied at certain nodal points on the vortex panels. An iterative technique is used to satisfy these conditions in order to obtain the vorticity distribution and the wake shape. Distributed and total aerodynamic loads are then calculated.

Kandil, O. A.↗
NASA NTRS1992

Some effects of wing and body geometry on the aerodynamic characteristics of configurations designed for high supersonic Mach numbers

Experimental and theoretical results are presented for a family of aerodynamic configurations for flight Mach numbers as high as Mach 8. All of these generic configurations involved 70-deg sweep delta planform wings of three different areas and three fuselage shapes with circular-to-elliptical cross sections. It is noted that fuselage ellipticity enhances lift-curve slope and maximum L/D, while decreasing static longitudinal stability (especially with smaller wing areas).

Spearman, M. L.↗
NASA NTRS1977

Subsonic and supersonic aerodynamic characteristics of a supersonic cruise fighter model with a twisted and cambered wing with 74 deg sweep

A wind tunnel investigation has been conducted to determine the longitudinal and lateral aerodynamic characteristics of a model of a supersonic cruise fighter configuration with a design Mach number of 2.60. The configuration is characterized by a highly swept arrow wing twisted and cambered to minimize supersonic drag due to lift, twin wing mounted vertical tails, and an aft mounted integral underslung duel-engine pod. The investigation also included tests of the configuration with larger outboard vertical tails and with small nose strakes.

Morris, O. A.↗
NASA NTRS1983

Flutter and steady/unsteady aerodynamic characteristics of supercritical and conventional transport wings

This paper presents the technical details and results of a high-speed wind-tunnel test program of an aeroelastic cantilevered transport type wing with two pylon-mounted engines. The tests were conducted in the NASA-Langley 16-foot Transonic Dynamic tunnel (TDT) during December 1981. Flutter of identical planforms, mass properties, and stiffness. The test parameters included different values of model stiffness and wing loading at various angles of attack. The models were instrumented at span-wise wing stations to determine bending and torsion deflections and vertical accelerations. At two model wing stations, pressure transducers were distributed along the chord to record static and unsteady oscillatory pressures during the approach to and onset of flutter. This paper presents the test program with results of the flutter characteristics and selected steady and unsteady aerodynamic data for both airfoils at different angles of attack for various Mach numbers and dynamic pressures.

Grosser, W. F.↗
NASA NTRS1955

Longitudinal Stability and Control Characteristics as Determined by the Rocket-Model Technique for an Inline, Cruciform, Canard Missile Configuration with a Low-Aspect-Ratio Wing Having Trailing-Edge Flap Controls for a Mach Number Range of 0.7 to 1.8

Two full-scale models of an inline, cruciform, canard missile configuration having a low-aspect-ratio wing equipped with flap-type controls were flight tested in order to determine the missile's longitudinal aerodynamic characteristics. Stability derivatives and control and drag characteristics are presented for a range of Mach number from 0.7 to 1.8. Nonlinear lift and moment curves were noted for the angle-of-attack range of this test (0 deg to 8 deg ). The aerodynamic-center location for angles of attack near 5 deg remained nearly constant for supersonic speeds at 13.5 percent of the mean aerodynamic chord; whereas for angles of attack near O deg, there was a rapid forward movement of the aerodynamic center as the Mach number increased. At a control deflection of O deg, the missile's response to the longitudinal control was in an essentially fixed space plane which was not coincident with the pitch plane as a result of the missile rolling. As a consequence, stability characteristics were determined from the resultant of pitch and yaw motions. The damping-in-pitch derivatives for the two angle-of-attack ranges of the test are in close agreement and varied only slightly with Mach number. The horn-balanced trailing-edge flap was effective in producing angle of attack over the Mach number range.

Baber, H. T., Jr.↗
NASA NTRS2017

Transonic Drag Reduction Through Trailing-Edge Blowing on the FAST-MAC Circulation Control Model

A third wind tunnel test of the FAST-MAC circulation control semi-span model was completed in the National Transonic Facility at the NASA Langley Research Center where the model was configured for transonic testing of the cruise configuration with 0deg flap detection to determine the potential for transonic drag reduction with the circulation control blowing. The model allowed independent control of four circulation control plenums producing a high momentum jet from a blowing slot near the wing trailing edge that was directed over a 15% chord simple-hinged ap. Recent upgrades to transonic semi-span flow control testing at the NTF have demonstrated an improvement to overall data repeatability, particularly for the drag measurement, that allows for increased confidence in the data results. The static thrust generated by the blowing slot was removed from the wind-on data using force and moment balance data from wind-o thrust tares. This paper discusses the impact of the trailing-edge blowing to the transonic aerodynamics of the FAST-MAC model in the cruise configuration, where at flight Reynolds numbers, the thrust-removed corrected data showed that an overall drag reduction and increased aerodynamic efficiency was realized as a consequence of the blowing.

Chan, David T.↗
NASA NTRS1977

Nonlinear, unsteady aerodynamic loads on rectangular and delta wings

Nonlinear unsteady aerodynamic loads on rectangular and delta wings in an incompressible flow are calculated by using an unsteady vortex-lattice model. Examples include flows past fixed wings in unsteady uniform streams and flows past wings undergoing unsteady motions. The unsteadiness may be due to gusty winds or pitching oscillations. The present technique establishes a reliable approach which can be utilized in the analysis of problems associated with the dynamics and aeroelasticity of wings within a wide range of angles of attack.

Atta, E. H.↗
NASA NTRS2018

Numerical Simulation of a Simplified High-Lift CRM Configuration Embedded with Fluidic Actuators

Numerical simulations have been performed for a simplified high-lift configuration that is representative of a modern transport airplane. This configuration includes a leading-edge slat, fuselage, wing, nacelle-pylon and a simple hinged flap. The suction surface of the flap is embedded with multiple rows of fluidic actuators to reduce the extent of reversed flow regions and improve the aerodynamic performance of the configuration with flap in a deployed state. In the current paper, a Lattice Boltzmann Method based high-fidelity computational fluid dynamics (CFD) code, known as PowerFLOW® is used to simulate the entire flow field associated with this configuration, including the flow inside the actuators. A fully compressible version of the PowerFLOW® code that has been validated for high speed flows is used for the present simulations to accurately represent the transonic flow regimes that are encountered in the flow field generated by the actuators operating at higher mass flow (momentum) rates required to mitigate reverse flow regions on the suction surfaces of the main wing and the flap. The numerical solutions predict the expected trends in aerodynamic forces as the actuation levels are increased. More efficient active flow control (AFC) systems and actuator arrangement for lift augmentation are emerging based on the parametric studies conducted here prior to wind tunnel tests. These numerical solutions will be compared with experimental data, once such data becomes available.

Vatsa, Veer N.↗
NASA NTRS1938

Spinning Characteristics of Wings V : N.A.C.A. 0009, 23018, and 6718 Monoplane Wings

Three rectangular monoplane wings having rounded tips were tested on the N.A.C.A. spinning balance in the 5-foot vertical wind tunnel. The airfoil sections used were the N.A.C.A. 0009, 23018, and 6718. The aerodynamic characteristics of the models and a prediction of the angles of sideslip for steady spins are given. There is included an estimate of the yawing moment that must be furnished by parts of the airplane to balance the inertia couples and wing yawing moments for spinning equilibrium. The predicted angles of sideslip and yawing moments required for spinning equilibrium for a Clark Y wing with the same form are included for comparison.

Bamber, M J↗
NASA NTRS1974

Equation solving program for aerodynamic lifting surface theory

A description of and user's manual are presented for one of a group of FORTRAN programs which, together, can be used for the analysis and design of wings in steady, subsonic flow according to a kernel function method lifting surface theory. This particular program is the one which solves the sets of simultaneous, linear, algebraic equations arising from the thin wing analysis. This program has the capability of striking out rows and columns of the aerodynamic influence matrix and rows of the associated boundary condition vectors (right hand sides). This capability significantly enhances the effectiveness of the kernel function method of lifting surface theory because studies of the convergence of solutions with the number of control points can be done with the calculation of only a single influence matrix.

Medan, R. T.↗
NASA NTRS1991

Incipient torsional stall flutter aerodynamic experiments on a swept three-dimensional wing

The aerodynamics of small amplitude pitching motions near stall have been studied experimentally in order to improve understanding of the torsional stall flutter problem for propeller blades. A model wing was oscillated in pitch at several small amplitudes over a wide and representative range of conditions. Unsteady surface pressures were measured and integrated to determine the aerodynamic damping at five spanwise stations. Strong negative damping was found for motions centered near static stall for all studied reduced frequencies, Mach numbers, and sweep angles. The 30-deg sweptback configuration was found to become negatively damped over the entire span nearly simultaneously, while the unswept model exhibited local regions of negative damping that moved toward the wing tip as the mean angle of attack was increased.

Lorber, Peter F.↗
NASA NTRS1974

Nonlinear prediction of the aerodynamic loads on lifting surfaces

A numerical procedure is used to predict the nonlinear aerodynamic characteristics of lifting surfaces of low aspect ratio at high angles of attack for low subsonic Mach numbers. The procedure utilizes a vortex-lattice method and accounts for separation at sharp tips and leading edges. The shapes of the wakes emanating from the edges are predicted, and hence the nonlinear characteristics are calculated. Parallelogram and delta wings are presented as numerical examples. The numerical results are in good agreement with the experimental data.

Kandil, O. A.↗