Search NASA⌕ Search

SEARCH · Search NASA

Results for “Statistical analysis.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Atmospheric Radiative Transfer for Satellite Remote Sensing: Validation and Uncertainty

My presentation will begin with the discussion of the Intercomparison of three-dimensional (3D) Radiative Codes (13RC) project that has been started in 1997. I will highlight the question of how well the atmospheric science community can solve the 3D radiative transfer equation. Initially I3RC was focused only on algorithm intercomparison; now it has acquired a broader identity providing new insights and creating new community resources for 3D radiative transfer calculations. Then I will switch to satellite remote sensing. Almost all radiative transfer calculations for satellite remote sensing are one-dimensional (1D) assuming (i) no variability inside a satellite pixel and (ii) no radiative interactions between pixels. The assumptions behind the 1D approach will be checked using cloud and aerosol data measured by the MODerate Resolution Imaging Spectroradiometer (MODIS) on board of two NASA satellites TERRA and AQUA. In the discussion, I will use both analysis technique: statistical analysis over large areas and time intervals, and single scene analysis to validate how well the 1D radiative transfer equation describes radiative regime in cloudy atmospheres.

Marshak, Alexander↗

Runtime Monitoring for Unmanned Aerospace Systems with Neural Network Components

AI components (e.g., Deep Neural Networks) are increasingly used in unmanned Aerospace systems for safety-relevant applications. Rigorous Verification and Validation methods for such components are still in their infancy and thus, monitoring of the AI's behavior during runtime is essential. In this paper, we will present a runtime-monitoring architecture, which combines the advanced statistical analysis framework SYSAI (System Analysis using Statistical AI) with temporal and probabilistic runtime monitoring carried out by R2U2 (Realizable, Responsive, and Unobtrusive Unit). Learned statistical models of complex systems with AI components are produced by the SYSAI framework and provide detailed information to enable the R2U2 runtime monitor to efficiently perform advanced safety and performance checks in nominal and off-nominal conditions. We will present initial results of our tool set and architecture on a case study, a DNN-based autonomous centerline tracking system (ACT).

Yuning He↗

Data Mining and Machine Learning for Power System Monitoring, Understanding, and Impact Evaluation

This chapter presents results from the Big Data analysis framework to improve power system situational awareness and system reliability. For this purpose, a dataset with real-world phasor measurement unit data and historical transmission system outage data has been created and used to carry out the analysis. Several statistical analysis and machine learning methods have been developed and implemented for event and anomaly detection and modeling. Detection and analysis results for actual examples of power system events are presented. Finally, data-driven characterization and risk assessment methods for weather-related extremes in power systems are developed and demonstrated on the Bonneville Power Administration system. These applications demonstrate the capability of Machine Learning (ML) methods to monitor system abnormalities, to predict system events, and to characterize the impact of extreme events on power grid

data mining, power grid, machine learning, anomaly↗

The OVIS analysis architecture.

This report summarizes the current statistical analysis capability of OVIS and how it works in conjunction with the OVIS data readers and interpolators. It also documents how to extend these capabilities. OVIS is a tool for parallel statistical analysis of sensor data to improve system reliability. Parallelism is achieved using a distributed data model: many sensors on similar components (metaphorically sheep) insert measurements into a series of databases on computers reserved for analyzing the measurements (metaphorically shepherds). Each shepherd node then processes the sheep data stored locally and the results are aggregated across all shepherds. OVIS uses the Visualization Tool Kit (VTK) statistics algorithm class hierarchy to perform analysis of each process's data but avoids VTK's model aggregation stage which uses the Message Passing Interface (MPI); this is because if a single process in an MPI job fails, the entire job will fail. Instead, OVIS uses asynchronous database replication to aggregate statistical models. OVIS has several additional features beyond those present in VTK that, first, accommodate its particular data format and, second, improve the memory and speed of the statistical analyses. First, because many statistical algorithms are multivariate in nature and sensor data is typically univariate, interpolation of data is required to provide simultaneous observations of metrics. Note that in this report, we will refer to a single value obtained from a sensor as a measurement while a collection of multiple sensor values simultaneously present in the system is an observation. A base class for interpolation is provided that abstracts the operation of converting multiple sensor measurements into simultaneous observations. A concrete implementation is provided that performs piecewise constant temporal interpolation of multiple metrics across a single component. Secondly, because calculations may summarize data too large to fit in memory OVIS analyses batches of observations at a time and aggregates these intermediate intra-process models as it goes before storing the final model for inter-process aggregation via database replication. This reduces the memory footprint of the analysis, interpolation, and the database client and server query processing. This also interleaves processing with the disk I/O required to fetch data from the database - also improving speed. This report documents how OVIS performs analyses and how to create additional analysis components that fetch measurements from the database, perform interpolation, or perform operations on streamed observations (such as model updates or assessments). The rest of this section outlines the OVIS analysis algorithm and is followed by sections specific to each subtask. Note that we are limiting our discussion for now to the creation of a model from a set of measurements, and not including the assessment of observations using a model. The same framework can be used for assessment but that use case is not detailed in this report.

97 MATHEMATICS AND COMPUTING↗

Statistical Signal Analysis for Systems with Interferenced Inputs

A new approach is introduced, based on statistical signal analysis, which overcomes the error due to input signal interference. The model analyzed is given. The input signals u sub 1 (t) and u sub 2 (t) are assumed to be unknown. The measurable signals x sub 1 (t) and x sub 2 (t) are interferened according to the frequency response functions, H sub 12 (f) and H sub 21 (f). The goal of the analysis was to evaluate the power output due to each input, u sub 1 (t) and u sub 2 (t), for the case where both are applied to the same time. In addition, all frequency response functions are calculated. The interferenced system is described by a set of five equations with six unknown functions. An IBM XT Personal Computer, which was interfaced with the FFT, was used to solve the set of equations. The software was tested on an electrical two-input, one-output system. The results were excellent. The research presented includes the analysis of the acoustic radiation from a rectangular plate with two force inputs and the sound pressure as an output signal.

Bai, R. M.↗

A thought experiment to evaluate a proposed data analysis method

A statistical analysis was recently presented at a DOE review in reference to a particular problem. Here we attempt to capture the essence of this problem with a simple “toy” analog and demonstrate the incorrectness of the presented J figure of merit algorithm. We show that the incorrect usage of J gives PDFs that have erroneous long tails and significantly overestimate the rms deviations relative to those obtained by exact analytic methods. Conversely, a numerical Bayesian analysis gives the correct result.

97 MATHEMATICS AND COMPUTING↗

Non-Operational Property Evaluation for the Hanford Site River Corridor - 12409

The Hanford Site River Corridor consists of the former reactor areas of the 100 Areas and the former industrial (fuel processing) area in the 300 Area. Most of the waste sites are located close to the decommissioned reactors or former industrial facilities along the Columbia River. Most of the surface area of the River Corridor consists of land with little or no subsurface infrastructure or indication of past or present releases of hazardous constituents, and is referred to as non-operational property or non-operational area. Multiple lines of evidence have been developed to assess identified fate and transport mechanisms and to evaluate the potential magnitude and significance of waste site-related contaminants in the non-operational area. Predictive modeling was used for determining the likelihood of locating waste sites and evaluating the distribution of radionuclides in soil based on available soil concentration data and aerial radiological surveys. The results of this evaluation indicated: 1) With the exception of stack emissions, transport pathways associated with waste site contaminants are unlikely to result in dispersion of contaminants in soil away from operational areas, 2) Stack emissions that may have been associated with Hanford Site operations generally emitted short-lived and/or gaseous radionuclides, and (3) the likelihood of detecting elevated radionuclide concentrations or other waste sites in non-operational area soils is very small. The overall conclusions from the NPE evaluation of the River Corridor are: - With the exception of stack emissions to the air, transport pathways associated with waste site contaminants are unlikely to result in dispersion of contaminants in soil away from operational areas. While pathways such as windblown dust, overland transport and biointrusion have the potential for dispersing waste site contaminants, the resulting transport is unlikely to result in substantial contamination in non-operational areas. - Stack emissions that may have been associated with Hanford Site operations generally emitted short-lived and/or gaseous radionuclides; these radionuclides either would have decayed and would be undetectable in soil, or likely would not have deposited onto Hanford Site soils. A small fraction of the total historical emissions consisted of long-lived particulate radionuclides, which could have deposited onto the soil. Soil monitoring studies conducted as part of surveillance and monitoring programs do not indicate a build-up of radionuclide concentrations in soil, which might indicate potential deposition impacts from stack emissions. Aerial radiological surveys of the Hanford Site, while effective in detecting gamma-emitting nuclides, also do not indicate deposition patterns in soil from stack emissions. - The surveillance and monitoring programs also have verified that the limited occurrence of biointrusion observed in the River Corridor has not resulted in a spread of contamination into the non-operational areas. - Monitoring of radionuclides in ambient air conducted as part of the surveillance and monitoring programs generally show a low and declining trend of detected concentrations in air. Monitoring of radionuclides in soil and vegetation correspondingly show declining trends in concentrations, particularly for nuclides with short half lives (Cs-137, Co-60 and Sr-90). - Statistical analysis of the geographical distribution of waste sites based on man -made features and topography describes the likely locations of waste sites in the River Corridor. The results from this analysis reinforce the findings from the Orphan Site Evaluation program, which has systematically identified any remaining waste sites within the River Corridor. - Statistical analysis of the distribution of radionuclide concentrations observable from aerial surveys has confirmed that the likelihood of detecting elevated radionuclide concentrations in non-operational area soils is very small; the occurrences and locations where potentially elevated concentrations may be found are discussed below. In addition, statistical analysis showed that there is a relatively high probability (>50%) that concentrations of Cs-137 higher than background (3.9 Bq/kg or 1.05 pCi/g) are located outside of the operational portion of the 100-BC, 100-K, and 100-N Areas. This observation is based on modeled concentrations in soil derived from aerial radiography data. However, the extent is limited to a few meters from the respective facilities fence lines or known operational activities. Evaluation of the extent of contamination is being conducted as part of the RI process for each decision area. No unanticipated waste sites were identified either from the OSE program or statistical analysis of waste site proximity to known features. Based on the evaluation of these multiple lines of evidence, the likelihood of identifying waste sites or contaminant dispersal from Hanford site operations into non-operational areas can be considered very small. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Vibration transmission through rolling element bearings. IV - Statistical energy analysis

A theoretical broadband coupling-loss factor is developed analytically for use in the statistical energy analysis (SEA) of a shaft-bearing-plate system. The procedure is based on the solution of the boundary-value problem at the plate-bearing interface and incorporates a bearing-stiffness matrix developed by the authors. Three examples are utilized to illustrate the SEA incorporating the coupling-loss factor including: (1) a shaft-bearing-plate system; (2) a plate-cantilevered beam; and (3) a circular-shaft-bearing plate. The coupling-loss factor in the case of the thin plate-cantilevered beam is found to be more accurate than that developed by Lyon and Eichler (1964). The coupling-loss factor is described for the bearing system and extended to describe the mean-square vibratory response of a rectangular plate. The proposed techniques are of interest to the study of vibration and noise in rotating machinery such as gearboxes.

Lim, T. C.↗

Statistical structural analysis of rotor impact ice shedding

The statistical characteristics of impact ice shear strength are analyzed, with emphasis placed on the most probable shear strength and statistical distribution of an ice deposit. Several distribution types are considered: the Weibull, two-parameter Weibull, and exponential distributions, as well as the Gumbell distribution of the smallest extreme and the Gumbell distribution of the largest extreme. It is concluded that the Weibull distribution yields the best results; however, the expected life, shape parameter, and scale parameter should be determined separately for each case of varying wind speed and droplet size. The theoretical predictions of shear stresses in a specific rotating ice shape are compared, and it is noted that when the effects of lift are added to the theoretical model and the interference is calculated with a new mean and standard deviation, the probability of ice shed is computed as 36.64 pct.

Kellacky, C. J.↗

Prediction of interior noise due to random acoustic or turbulent boundary layer excitation using statistical energy analysis

The feasibility of predicting interior noise due to random acoustic or turbulent boundary layer excitation was investigated in experiments in which a statistical energy analysis model (VAPEPS) was used to analyze measurements of the acceleration response and sound transmission of flat aluminum, lucite, and graphite/epoxy plates exposed to random acoustic or turbulent boundary layer excitation. The noise reduction of the plate, when backed by a shallow cavity and excited by a turbulent boundary layer, was predicted using a simplified theory based on the assumption of adiabatic compression of the fluid in the cavity. The predicted plate acceleration response was used as input in the noise reduction prediction. Reasonable agreement was found between the predictions and the measured noise reduction in the frequency range 315-1000 Hz.

Grosveld, Ferdinand W.↗

Power flow as a complement to statistical energy analysis and finite element analysis

Present methods of analysis of the structural response and the structure-borne transmission of vibrational energy use either finite element (FE) techniques or statistical energy analysis (SEA) methods. The FE methods are a very useful tool at low frequencies where the number of resonances involved in the analysis is rather small. On the other hand SEA methods can predict with acceptable accuracy the response and energy transmission between coupled structures at relatively high frequencies where the structural modal density is high and a statistical approach is the appropriate solution. In the mid-frequency range, a relatively large number of resonances exist which make finite element method too costly. On the other hand SEA methods can only predict an average level form. In this mid-frequency range a possible alternative is to use power flow techniques, where the input and flow of vibrational energy to excited and coupled structural components can be expressed in terms of input and transfer mobilities. This power flow technique can be extended from low to high frequencies and this can be integrated with established FE models at low frequencies and SEA models at high frequencies to form a verification of the method. This method of structural analysis using power flo and mobility methods, and its integration with SEA and FE analysis is applied to the case of two thin beams joined together at right angles.

Cuschieri, J. M.↗

Statistical energy analysis of a geared rotor system

The vibroacoustic response of a generic geared rotor system is analyzed on an order of magnitude basis utilizing an approximate statistical energy analysis method. This model includes a theoretical coupling loss factor for a generic bearing component, which properly accounts for the vibration transmission through rolling element bearing. A simplified model of a NASA test stand that assumes vibratory energy flow from the gear mesh source to the casing through shafts and bearings is given as an example. Effects of dissipation loss factor and gearbox radiation efficiency models are studied by comparing predictions with NASA test results.

Lim, Teik C.↗

Atmospheric turbulence simulation techniques with application to flight analysis

Statistical modeling of atmospheric turbulence is discussed. The statistical properties of atmospheric turbulence, in particular the probability distribution, the spectra, and the coherence are reviewed. Different atmospheric turbulence simulation models are investigated, and appropriate statistical analyses are carried out to verify their validity. The models for simulation are incorporated into a computer model of aircraft flight dynamics. Statistical results of computer simulated landings for an aircraft having characteristics of a DC-8 are reported for the different turbulence simulation techniques. The significance of various degrees of sophistication in the turbulence simulation techniques on the landing performance of the aircraft is discussed.

Wang, S. T.↗

On the effects of filtering on convective-core statistics

Analysis of convective events north of Australia during the equatorial Monsoon Experiment (EMEX) reinforces accumulating evidence that convective cores over the tropical ocean are weak, with small diameters and vertical velocities. Superposition of smaller-scale turbulence on the convective core signal could yield artificially small cores, and thus produce sampling bias by aircraft. To investigate this potential source of bias, a side-by-side analysis of filtered and unfiltered vertical velocity data was performed while investigating the EMEX convective cores. Data were collected by the NOAA P3 and NCAR Electra using filtered (Graham filter) and non-filtered cores. The effects of filtering vertical velocity data to identify updraft and downdraft cores were noticeable but smaller than expected. Updraft cores had a vertical velocity greater than 1 m/sec for at least 500 m, and downdraft cores were defined analogously so that the filter eliminated events with less than a 500 m apparent diameter. Median and 10 percent core diameters were increased by 20-25 percent at most, with larger increases at higher levels (fewer small events). The maximum vertical velocity was changed only by changing the individual events in the distribution, but changes were detectable. At the lower levels, where many small, weak cores are introduced by filtering, average vertical velocity for the updraft cores was lowered by up to around 10 percent. Mass flux was changed the least, since diameter and mean vertical velocity respond to filtering in opposite ways. The filtering procedure increased total mass flux slightly due to inclusion of more upward moving air into the sample.

Lemone, Margaret A.↗