Search NASA⌕ Search

SEARCH · Search NASA

Results for “array data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

A novel method of calculating far-field patterns of large aperture antennas

A method is described for calculation of the radiation pattern of large aperture antennas. A piece-wise linear approximation of the aperture field using overlapping pyramidal basis functions allows the radiation pattern of an aperture antenna to be calculated as though it were a two-dimensional array. The calculation of radiation pattern data versus theta and phi, suitable for 3-D or contour plot algorithms, is achieved by locating the array in the yz-plane and performing a summation over the aperture field data sampled on a square grid. A FORTRAN subroutine is provided for performing radiation pattern calculations. Numerical results are included to demonstrate the accuracy and convergence of the method. These numerical results indicate that typical accuracies of + or - 0.1 dB for Directivity, + or - dB for the 1st Sidelobe Level, and + - 2dB for the 2nd Sidelobe Level can be obtained with an aperture grid of 45x45 points and requires approximately 0.02 seconds CPU time per far-field data point on a VAX 11/750 with a floating point accelerator.

Bailey, M. C.↗
NASA NTRS1994

Optimizing the Galileo space communication link

The Galileo mission was originally designed to investigate Jupiter and its moons utilizing a high-rate, X-band (8415 MHz) communication downlink with a maximum rate of 134.4 kb/sec. However, following the failure of the high-gain antenna (HGA) to fully deploy, a completely new communication link design was established that is based on Galileo's S-band (2295 MHz), low-gain antenna (LGA). The new link relies on data compression, local and intercontinental arraying of antennas, a (14,1/4) convolutional code, a (255,M) variable-redundancy Reed-Solomon code, decoding feedback, and techniques to reprocess recorded data to greatly reduce data losses during signal acquisition. The combination of these techniques will enable return of significant science data from the mission.

Statman, J. I.↗
NASA NTRS1978

Concentrator enhanced solar arrays design study

The analysis and preliminary design of a 25 kW concentrator enhanced lightweight flexible solar array are presented. The study was organized into five major tasks: (1) assessment and specification of design requirements; (2) mechanical design; (3) electric design; (4) concentrator design; and (5) cost projection. The tasks were conducted in an iterative manner so as to best derive a baseline design selection. The objectives of the study are discussed and comparative configurations and mass data on the SEP (Solar Electric Propulsion) array design, concentrator design options and configuration/mass data on the selected concentrator enhanced solar array baseline design are presented. Design requirements supporting design analysis and detailed baseline design data are discussed. The results of the cost projection analysis and new technology are also discussed.

Lott, D. R.↗
NASA NTRS2010

Phenological Parameters Estimation Tool

The Phenological Parameters Estimation Tool (PPET) is a set of algorithms implemented in MATLAB that estimates key vegetative phenological parameters. For a given year, the PPET software package takes in temporally processed vegetation index data (3D spatio-temporal arrays) generated by the time series product tool (TSPT) and outputs spatial grids (2D arrays) of vegetation phenological parameters. As a precursor to PPET, the TSPT uses quality information for each pixel of each date to remove bad or suspect data, and then interpolates and digitally fills data voids in the time series to produce a continuous, smoothed vegetation index product. During processing, the TSPT displays NDVI (Normalized Difference Vegetation Index) time series plots and images from the temporally processed pixels. Both the TSPT and PPET currently use moderate resolution imaging spectroradiometer (MODIS) satellite multispectral data as a default, but each software package is modifiable and could be used with any high-temporal-rate remote sensing data collection system that is capable of producing vegetation indices. Raw MODIS data from the Aqua and Terra satellites is processed using the TSPT to generate a filtered time series data product. The PPET then uses the TSPT output to generate phenological parameters for desired locations. PPET output data tiles are mosaicked into a Conterminous United States (CONUS) data layer using ERDAS IMAGINE, or equivalent software package. Mosaics of the vegetation phenology data products are then reprojected to the desired map projection using ERDAS IMAGINE

McKellip, Rodney D.↗
NASA NTRS1972

Feasibility investigation of a cellularly organized data processor

The application of cellular arrays to NASA missions was studied. Cellular arrays are iterative logical and memory structures which can be programmed to accomplish a wide variety of logical tasks. Used in long-duration space missions, spare cellular arrays can be remotely programmed to replace faulty logical subsystems as the need arises.

Minnick, R. C.↗
NASA NTRS1996

Survey of Experimental Results From One Year of PASP PLUS Orbital Operation

With PASP Plus as its primary payload, the APEX satellite was launched by a standard Pegasus rocket released from a NASA B-52 aircraft on 3 August 1994. A 70 deg inclination, 363 km X 2550 km orbit was achieved, allowing both investigation of space plasma effects on high-voltage operation in the perigee region and investigation of space radiation effects on array power output from passage through the inner radiation belt in the apogee region. Data gathering by PASP Plus was begun on 7 Aug 94 and ended on 11 Aug 95. In one year, PASP Plus collected an order of magnitude more data on environmental interactions on solar arrays than all previous space-borne photovoltaic experiments combined. The test arrays flown and the interactions-measuring and space-environment sensors of PASP Plus are described. The results of measurements of leakage current under test-array positive biasing and arc rates under negative biasing as a function of bias voltage, plasma density, array orientation, and other conditions are presented. The results of measurements of test-array power-output degradation caused by space radiation are also examined.

PHOTOVOLTAIC EFFECT↗
NASA NTRS2019

Noise Abatement Flight Test Data Report

An acoustic flight test of six helicopters conducted by NASA, FAA, and the US Army is described. Microphone arrays were used to collect acoustic data for source noise characterization, to investigate the acoustic impacts of maneuvering flight, and to develop and evaluate noise abatement operations for helicopters on approach. Atmospheric data and vehicle state data were also collected. Noise metrics are calculated and plotted for all conditions tested. All data described are publicly available upon request.

Rotorcraft↗
NASA NTRS2008

Preliminary Analysis of Acoustic Measurements from the NASA-Gulfstream Airframe Noise Flight Test

The NASA-Gulfstream joint Airframe Noise Flight Test program was conducted at the NASA Wallops Flight Facility during October, 2006. The primary objective of the AFN flight test was to acquire baseline airframe noise data on a regional jet class of transport in order to determine noise source strengths and distributions for model validation. To accomplish this task, two measuring systems were used: a ground-based microphone array and individual microphones. Acoustic data for a Gulfstream G550 aircraft were acquired over the course of ten days. Over twenty-four test conditions were flown. The test matrix was designed to provide an acoustic characterization of both the full aircraft and individual airframe components and included cruise to landing configurations. Noise sources were isolated by selectively deploying individual components (flaps, main landing gear, nose gear, spoilers, etc.) and altering the airspeed, glide path, and engine settings. The AFN flight test program confirmed that the airframe is a major contributor to the noise from regional jets during landing operations. Sound pressure levels from the individual microphones on the ground revealed the flap system to be the dominant airframe noise source for the G550 aircraft. The corresponding array beamform maps showed that most of the radiated sound from the flaps originates from the side edges. Using velocity to the sixth power and Strouhal scaling of the sound pressure spectra obtained at different speeds failed to collapse the data into a single spectrum. The best data collapse was obtained when the frequencies were left unscaled.

Khorrami, Mehdi R.↗
NASA NTRS1973

Updated optical read/write memory system components

The fabrication of an updated block data composer and holographic storage array for a breadboard holographic read/write memory system is described. System considerations such as transform optics and controlled aberration lens design are described along with the block data composer, photoplastic recording materials, and material development.

Source record↗
NASA NTRS2018

Radiation Performance of Memory Technologies for Space Applications

MRAM and DRAM memory technologies identified for possible radiation hardening were investigated for memory-array- and controller-level radiation sensitivity. TID and SEE performance of memory arrays and associated cells is good, but with some questions about viability of hardening of problematic control circuitry. Control-circuitry-related SEE problems are highlighted. TID data are focused on memory arrays only.

Some, Raphael↗
NASA NTRS1980

Two-dimensional VLA maps of solar bursts at 15 and 23 GHz with arcsec resolution

Three small, impulsive solar-microwave bursts (peak fluxes 4.9, 3.0, and 0.4 sfu) were observed during 1979 September 7-9, using the Very Large Array (VLA) at 15.05 or 22.5 GHz. The data from 10 antennas distributed on three arms of the array provide the first two-dimensional burst images with spatial resolution as high as 1.0 x 0.75 arcsec. Comparison with optical data showed in the impulsive phase of all three flares, the microwave emission was dominated by a compact source located between the H-alpha kernels. In the post-impulsive phase, the microwave source was larger and elongated in a direction consistent with the orientation of the magnetic field lines joining the H-alpha kernels. These results are interpreted to imply that the initial energy release occurs near the top of the magnetic arch joining the H-alpha kernels.

Marsh, K. A.↗
NASA NTRS1982

Integrated infrared detector arrays for low-background applications

Advanced infrared detector and detector array technology is being developed and characterized for future NASA space astronomy applications. Si:Bi charge-injection-device arrays have been obtained, and low-background sensitivities comparable to that of good discrete detectors have been measured. Intrinsic arrays are being assessed, and laboratory and telescope data have been collected on a monolithic InSb CCD array. For wavelengths longer than 30 microns, improved Ge:Ga detectors have been produced, and steps have been taken to prove the feasibility of an integrated extrinsic germanium array. Other integrated arrays and cryogenic components are also under investigation.

Mccreight, C. R.↗
NASA NTRS1988

Space shuttle phase B wind tunnel model and test information. Volume 3: Launch configuration

Archived wind tunnel test data are available for flyback booster or other alternate recoverable configuration as well as reusable orbiters studied during initial development (Phase B) of the Space Shuttle, including contractor data for an extensive variety of configurations with an array of wing and body planforms. The test data have been compiled into a database and are available for application to current winged flyback or recoverable booster aerodynamic studies. The Space Shuttle Phase B Wind Tunnel Database is structured by vehicle component and configuration. Basic components include booster, orbiter, and launch vehicle. Booster configuration types include straight and delta wings, canard, cylindrical, retroglide and twin body. Orbiter configurations include straight and delta wings, lifting body, drop tanks and double delta wings. Launch configurations include booster and orbiter components in various stacked and tandem combinations. The digital database consists of 220 files containing basic tunnel data. Database structure is documented in a series of reports which include configuration sketches for the various planforms tested. This is Volume 3 -- launch configurations.

Glynn, J. L.↗
NASA NTRS2000

The S2 VLBI Systems: DAS, RT/PT and Correlator

The S2 VLBI system synthesizes wide IF bandwidths by rapidly switching the local oscillator (LO) frequency in a small (1-4) number of baseband converters (BBC's). Data are recorded on video cassettes using an array of 8 VHS transports. Characteristics of the S2 Data Acquisition System (DAS), the S2 Record and Playback Terminals (RT and PT) and the S2 Correlator are summarized. The bandwidth synthesis (BWS) frequency switching sequence used in a series of system validation experiments is presented.

Petrachenko, William T.↗
NASA NTRS1999

Got an Attitude Problem?

Through a Small Business Innovation Research grant from NASA's Goddard Space Flight Center, Servo Corporation of America, Inc. built its Mini-Dual Sensor to provide attitude control for Earth-orbiting unmanned satellites. The sensor is an Earth horizon sensor that provides higher accuracy through the use of pyroelectric arrays and a patented radiance compensation scheme.This sensor gathers data with two pairs of lithium tantalate pyroelectric arrays that are positioned 90 degrees apart in the imaging plane. The Mini-Dual Earth Sensor is a high-accuracy sensor that could be used for attitude determination in future space missions.

Source record↗
NASA NTRS2005

Lightning Mapping and the Nowcasting of Severe Storms

This paper describes a successful research and operational collaboration between NASA scientists and NWS forecasters to improve severe stor m warnings using real-time data from a regional VHF total lightning mapping array (LMA). Key objectives of our research using LMA data ar e: a) Identification of intensifying and weakening storms using the time rate-of-change of total flash rate; b) Improved severe storm poten tial situational awareness; c) Evaluation of the potential of total f lash rate trend to improve severe storm probability of detection (POD ) and lead time; and d) Validation of mesoscale model forecasts of th understorm initiation. The LMA data are distributed for ingest and di splay in the WFO AWIPS decision support system, and archived at each WFO for case studies, event playbacks, and assessments using the NWS Warning Event Simulator. The Huntsville WFO has upgraded severe thund erstorm warnings to verified tornado warnings and avoided a false ala rm on a severe storm through the added information on storm growth, intensification, and decay that can be deduced from the magnitude and temporal trend of total flash rates. We present detailed case studies of the observed relationships between lightning activity and tornadi c storm development as determined by radar reflectivity and velocity fields, and thunderstorms forecast by the Weather Research and Foreca st (WRF) model. From these collaborative studies, forecasters can eva luate the added value of total lightning data within the forecast and warning decision-making process (http://weather.msfc.nasa.gov/sport) .

Goodman, S.↗
NASA NTRS1989

Installed propfan (SR-7L) far-field noise characteristics

Far-field noise characteristics of the SR-7L single-rotor propfan were obtained from the Propfan Test Assessment (PTA) aircraft flight tests. The aircraft was flown at low altitudes (about 310m) above the ground at a constant speed of about 92 m/sec. The acoustic data were acquired with an array of ground-flush microphones positioned on both sides of the flight path. Propfan-generated noise levels were extracted from the total aircraft noise, and these data were then used to study the far-field noise characteristics. The directivities at the polar and azimuthal planes, and the variations of the blade-order tone levels with propfan power and blade tip Mach number were derived. The effect of inflow angle was studied by changing the nacelle tilt angle. The levels and the directivity were very sensitive to the nacelle tilt angle (i.e., inflow angle). The noise levels in the aft quadrant were found to be higher than in the forward quadrant. Also, the noise levels on the starboard side of the aircraft were found to be higher than on the port side. The noise levels increase with propfan power and rotational speed.

Reddy, N. N.↗
NASA NTRS2002

The Stretched Lens Array (SLA): An Ultra-Light Photovoltaic Concentrator

A high-performance, ultralight, photovoltaic concentrator array is being developed for space power. The stretched lens array (SLA) uses stretched-membrane, silicone Fresnel lenses to concentrate sunlight onto triple-junction photovoltaic cells. The cells are mounted to a composite radiator structure. The entire solar array wing, including lenses, photovoltaic cell flex circuits, composite panels, hinges, yoke, wiring harness, and deployment mechanisms, has a mass density of 1.6 kg/sq.m. NASA Glenn has measured 27.4% net SLA panel efficiency, or 375 W/sq.m. power density, at room temperature. At GEO operating cell temperature (80 C), this power density will be 300 W/sq.m., resulting in more than 180 W/kg specific power at the full wing level. SLA is a direct ultralight descendent of the successful SCARLET array on NASA's Deep Space 1 spacecraft. This paper describes the evolution from SCARLET to SLA, summarizes the SLA's key features, and provides performance and mass data for this new concentrator array.

ONeill, Mark J.↗