Search NASA⌕ Search

SEARCH · Search NASA

Results for “material response simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Waste Characterization Methods Based on Gamma-ray Imaging Spectrometers - 19454

Characterization of LLW, ILW, U, NORM and TENORM is critical to the nuclear industry's bottom line. Accurate measurements enable the disposal of waste at the lowest possible cost. In the past the most accurate technology available involved using HPGe detectors and extensive system modeling to estimate the total source term given what the user knows about the geometry of the source and any shielding between the source and the detectors. Now there are a variety of imaging detectors that are available commercially, including CZT and HPGe detectors that achieve energy resolution ≤1% FWHM at 662 keV. These devices couple the traditional high resolution spectroscopic analysis with next generation gamma-ray imaging information to more accurately characterize the radiation source term. Uncertainties in the source location will result in significant error in the characterization of an object's radioactivity. It is helpful if the object can be spun, such as a barrel, so that any asymmetry in the source distribution is averaged out from the detector's point of view. Even in the case of a spinning barrel it is important to determine if the radiation is concentrated near the center of the barrel or distributed near the edge. The closer one measures to a barrel, which usually dictates the time required to acquire data, the more these spatial variations in the source distribution will affect the calculated activity of each isotope. This paper will focus on showing the use of CZT imaging spectrometers to characterize complicated radiation source terms. The radiation images are used to determine where the source term should be defined in a radiation transport model that calculates the expected number of photopeak counts for each isotope detected. This is used to calculate the activity of the source. The transport model is used to determine the attenuation of the radiation source term through distance and shielding material, but the detection efficiency is based solely on radiation measurement data. These measurements are taken with a robotic source positioning device that allows for detailed directional efficiency calibration. It is a fully automated system where a detector is loaded into the device and all of the efficiency curves are captured as a function of direction by creating new measurements for each location the robot positions the source. These measurements are tagged with the true source location and the efficiency curve is calculated for each measurement. This is used to create a response function matrix as a function of energy and incident direction which is used to convert the direction dependent flux on the detector head determined from the simulation model to the expected number of counts per unit activity of each isotope of interest. The results of these source term reconstructions in both the spatial and spectral domain will be shown. The impact of improper specification of the source term will be shown for a few standard waste characterization scenarios to demonstrate the importance of proper source location determination. Finally, the underlying calibration method and some sample efficiency curves as a function of direction will be shown to demonstrate the importance of calibrating out directional response functions in imaging devices (which often have a strong forward sensitivity bias). (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2017

Local polar fluctuations in lead halide perovskite crystals

Hybrid lead-halide perovskites have emerged as an excellent class of photovoltaic materials. Recent reports suggest that the organic molecular cation is responsible for local polar fluctuations that inhibit carrier recombination. We combine low-frequency Raman scattering with first-principles molecular dynamics (MD) to study the fundamental nature of these local polar fluctuations. Our observations of a strong central peak in the cubic phase of both hybrid (CH 3 NH 3 PbBr 3 ) and all-inorganic (CsPbBr 3 ) lead-halide perovskites show that anharmonic, local polar fluctuations are intrinsic to the general lead-halide perovskite structure, and not unique to the dipolar organic cation. Furthermore, MD simulations indicate that head-to-head Cs motion coupled to Br face expansion, occurring on a few hundred femtosecond time scale, drives the local polar fluctuations in CsPbBr 3 .

36 MATERIALS SCIENCE↗
NASA NTRS2012

Space Environmental Effects Testing Capability at the Marshall Space Flight Center

Understanding the effects of the space environment on materials and systems is fundamental and essential for mission success. If not properly understood and designed for, the effects of the environment can lead to degradation of materials, reduction of functional lifetime, and system failure. In response to this need, the Marshall Space Flight Center has developed world class Space Environmental Effects (SEE) expertise and test facilities to simulate the space environment. Capabilities include multiple unique test systems comprising the most complete SEE testing capability available. These test capabilities include charged particle radiation (electrons, protons, ions), ultraviolet radiation (UV), vacuum ultraviolet radiation (VUV), atomic oxygen, plasma effects, space craft charging, lunar surface and planetary effects, vacuum effects, and hypervelocity impacts as well as the combination of these capabilities. In addition to the uniqueness of the individual test capabilities, MSFC is the only NASA facility where the effects of the different space environments can be tested in one location. Combined with additional analytical capabilities for pre- and post-test evaluation, MSFC is a one-stop shop for materials testing and analysis. The SEE testing and analysis are performed by a team of award winning experts nationally recognized for their contributions in the study of the effects of the space environment on materials and systems. With this broad expertise in space environmental effects and the variety of test systems and equipment available, MSFC is able to customize tests with a demonstrated ability to rapidly adapt and reconfigure systems to meet customers needs. Extensive flight experiment experience bolsters this simulation and analysis capability with a comprehensive understanding of space environmental effects.

DeWittBurns, H.↗
NASA NTRS1993

Nonlinear probabilistic finite element models of laminated composite shells

A probabilistic finite element analysis procedure for laminated composite shells has been developed. A total Lagrangian finite element formulation, employing a degenerated 3-D laminated composite shell with the full Green-Lagrange strains and first-order shear deformable kinematics, forms the modeling foundation. The first-order second-moment technique for probabilistic finite element analysis of random fields is employed and results are presented in the form of mean and variance of the structural response. The effects of material nonlinearity are included through the use of a rate-independent anisotropic plasticity formulation with the macroscopic point of view. Both ply-level and micromechanics-level random variables can be selected, the latter by means of the Aboudi micromechanics model. A number of sample problems are solved to verify the accuracy of the procedures developed and to quantify the variability of certain material type/structure combinations. Experimental data is compared in many cases, and the Monte Carlo simulation method is used to check the probabilistic results. In general, the procedure is quite effective in modeling the mean and variance response of the linear and nonlinear behavior of laminated composite shells.

Engelstad, S. P.↗
DOE OSTI2022

Effects of internal swelling on residual elasticity of a quasi-brittle material through a composite sphere model

This work describes the development of a micromechanical-based constitutive model accounting for the effect of internal expansion on the residual elasticity of a Hashin composite material. This material is made of spherical inclusions that are subjected to gradual swelling within a quasi-brittle matrix. The main focus of this work is to describe and analyze the material mechanical response, with an additional focus on the internal swelling’s effect on the stress–strain response and residual elasticity. Microstructural features and parameters of major importance for the mechanical responses were identified. The innovative characteristics of the proposed approach are summarized as follows: (1) a full determination of the physics of a complete-damage problem throughout the whole process of inclusion swelling with upscaling techniques, which transfers the microcrack-related properties from the lower scale to upper scale; and (2) an evolution of the mechanical fields and the corresponding residual elasticity for various inclusion swelling levels. Concerning the matrix–inclusion composite, it was hypothesized that only the matrix was susceptible to cracking, with varied degrees of damage, whereas the inclusions behave elastically and the elastic modulus of the expanding inclusions remains constant. It is to emphasize that the gradual swelling of inclusions is modeled by an increasing strain in the current micromechanical-based constitutive model, and the microcracks are represented by a set of randomly oriented penny-shaped microcracks with identical radii (namely, closed cracks). The main contribution of the current research is to establish the exact mathematical solutions for the mechanical fields (stress, strain) caused by the swelling of the inclusions (mechanical loading) and derive the effective residual elasticity of a composite (structural response) subject to internal expansion and quasi-brittle damage. Based on the assumption of closed cracks that could be extended to open cracks in the upcoming work, the results proposed by the present paper help to understand the non-linear mechanical behavior of quasi-brittle materials subject to microcracking and provide a theoretical framework to be used as academical benchmark for numerical simulations.

36 MATERIALS SCIENCE↗
NASA NTRS2012

Simulating the Impact Response of Full-Scale Composite Airframe Structures

NASA Langley Research Center obtained a composite helicopter cabin structure in 2010 from the US Army's Survivable Affordable Repairable Airframe Program (SARAP) that was fabricated by Sikorsky Aircraft Corporation. The cabin had been subjected to a vertical drop test in 2008 to evaluate a tilting roof concept to limit the intrusion of overhead masses into the fuselage cabin. Damage to the cabin test article was limited primarily to the roof. Consequently, the roof area was removed and the remaining structure was cut into test specimens including a large subfloor section and a forward framed fuselage section. In 2011, NASA and Sikorsky entered into a cooperative research agreement to study the impact responses of composite airframe structures and to evaluate the capabilities of the explicit transient dynamic finite element code, LS-DYNA®, to simulate these responses including damage initiation and progressive failure. Most of the test articles were manufactured of graphite unidirectional tape composite with a thermoplastic resin system. However, the framed fuselage section was constructed primarily of a plain weave graphite fabric material with a thermoset resin system. Test data were collected from accelerometers and full-field photogrammetry. The focus of this paper will be to document impact testing and simulation results for the longitudinal impact of the subfloor section and the vertical drop test of the forward framed fuselage section.

Fasanella, Edwin L.↗
DOE OSTI2023

Temperature Dependence of Band Gap Renormalization in High-T Sensor Materials via First-Principles and Experimental Corroboration

Understanding the temperature dependence of functional properties of high-T gas sensing materials is vital for their applications in combustion environments. The electron-phonon coupling that derives the electronic structure change with temperatures is a key property of interest as it affects other sensing responses. Herein, we assess the temperature dependence of band gap renormalization in metal oxides and perovskites by employing Allen-Heine-Cardona theory with first-principles simulations and corroborate with experimental observation. The calculated temperature-dependent band gap changes of these materials studied are in good agreement with in-house experimental data, proving that the theory can adequately predict renormalization on the band gap in the system of interest. The predicted and measured band gap variations are characterized using an analytical model, which can provide useful insights on the simulated zero-temperature band gaps. Based on the available data, a set of 53 metal oxides and perovskites were identified as potential high-T gas sensors. A machine learning model has been developed to predict the band-gap change by capturing the overall trend of the empirical parameters with respect to a reduced feature obtained by transforming the set of available physical features.

Park, Jongwoo↗
NASA NTRS2001

Modeling the Gas Dynamics Environment in a Subscale Solid Rocket Test Motor

Subscale test motors are often used for the evaluation of solid rocket motor component materials such as internal insulation. These motors are useful for characterizing insulation performance behavior, screening insulation material candidates and obtaining material thermal and ablative property design data. One of the primary challenges associated with using subscale motors however, is the uncertainty involved when extrapolating the results to full-scale motor conditions. These uncertainties are related to differences in such phenomena as turbulent flow behavior and boundary layer development, propellant particle interactions with the wall, insulation off-gas mixing and thermochemical reactions with the bulk flow, radiation levels, material response to the local environment, and other anomalous flow conditions. In addition to the need for better understanding of physical mechanisms, there is also a need to better understand how to best simulate these phenomena using numerical modeling approaches such as computational fluid dynamics (CFD). To better understand and model interactions between major phenomena in a subscale test motor, a numerical study of the internal flow environment of a representative motor was performed. Simulation of the environment included not only gas dynamics, but two-phase flow modeling of entrained alumina particles like those found in an aluminized propellant, and offgassing from wall surfaces similar to an ablating insulation material. This work represents a starting point for establishing the internal environment of a subscale test motor using comprehensive modeling techniques, and lays the groundwork for improving the understanding of the applicability of subscale test data to full-scale motors. It was found that grid resolution, and inclusion of phenomena in addition to gas dynamics, such as two-phase and multi-component gas composition are all important factors that can effect the overall flow field predictions.

Eaton, Andrew M.↗
DOE OSTI2025

Enhancing heat pump water heater performance with embedded phase change materials thermal energy storage: First hour rating improvement and demand response operation

The increasing global emphasis on energy efficiency and sustainability has put heat pump water heaters (HPWHs) in the spotlight as an energy-efficient alternative to traditional water heating systems. However, their widespread adoption is limited by challenges such as insufficient First Hour Rating (FHR), suboptimal control mechanisms, and limited flexibility for demand response operations. Here, to address these limitations, this study proposes an innovative HPWH system integrated with embedded phase change material (PCM)-based thermal energy storage (TES). The research introduces a novel design and control strategy that leverages optimized PCM integration to enhance thermal storage capacity, improve hot water delivery during peak demand, and increase load-shifting potential. A combination of system modeling, performance simulation, and demand response control strategy evaluation was employed to quantify the benefits of PCM integration. Results demonstrate that the proposed PCM-TES HPWH system significantly enhances FHR, with an optimal 7.0 lb. of PCM increasing FHR by over 26 %—from 62 to 78 gal—for a standard 50-gal HPWH. Additionally, under advanced demand response operation using a preheat strategy, the system reduces the percentage of control temperature out-of-band time from 65 % (conventional HPWH) to just 11.6 %, enabling a more stable and efficient hot water supply. This research contributes a novel PCM-embedded HPWH design and control framework that addresses both performance and grid-interactivity challenges. The findings offer a viable pathway to enhancing the operational efficiency, flexibility, and grid responsiveness of residential water heating systems.

Demand response control↗
DOE OSTI2024

Stress localization investigation of additively manufactured GRCop-42 thin-wall structure

A full-field crystal plasticity (CP) framework is presented for the GRCop-42 alloy to study microscopic mechanical behavior and local stress heterogeneities. The microstructures of additively manufactured (AM) materials are often unique relative to conventionally processed materials, and the local thermal histories drive these differences during the build process. These thermal histories depend on the process parameters (laser power, scan speed, and scan strategy) and the part geometry. Prior research has shown that the mechanical properties of thin-walled structures can vary significantly with wall thickness due to changes in the thermal boundary conditions during manufacturing. It is, therefore, desirable to perform CP simulations based on the phenomenological constitutive model to predict the local mechanical responses induced by microstructural heterogeneities. This work generates representative microstructures based on experimentally collected grain information (i.e., texture) for grain scale stress analysis, and the material constitutive parameters are calibrated using the experimental mechanical testing data. Here, we specifically investigated the effect of crystallographic texture and grain morphologies on the size-dependent mechanical properties of AM GRCop-42. The selection of appropriate material properties for implementing an effective free surface boundary condition and the influence of adjacent buffer layers are also discussed. Analysis of local field results reveals a strong correlation between stress localization and the initial grain orientation. However, no significant relationship between the misorientation of the individual adjacent grains and the average misorientation is observed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigation of the irradiation effects in additively manufactured 316L steel resulting in decreased irradiation assisted stress corrosion cracking susceptibility

While additive manufacturing (AM) is an area of increasing interest to the nuclear industry, there are significant research and development needs prior to successful implementation of additively manufactured components into reactors. AM steel behaves differently than traditional wrought material, as has been observed in numerous mechanical testing studies. The nuclear industry must also understand the material response to irradiation. This work examines the irradiation damage and the irradiation assisted stress corrosion cracking behavior (IASCC) of both proton irradiated AM and wrought 316L steel. For IASCC testing, specimens were strained to 4% plastic strain in a simulated boiling water reactor environment (288°C, 0.2 µS/cm). Transmission and scanning electron microscopy, confocal microscopy, and X-ray computed tomography were used to examine coupons of the material as well as tensile bars used in the IASCC testing. This work found that the wrought 316L was more susceptible to IASCC than the AM steel, however, some IASCC was observed in the AM steel when tested with the tensile axis parallel to the build direction. Electron microscopy has shown significantly fewer radiation induced voids formed in the AM steel. While the pre-existing pore network in the AM steel may act as a sink to point defects, this is not expected to be the major factor in the reduced swelling observed in the AM steel. The lower density of radiation induced voids was expected to contribute to the IASCC resistance by decreasing the localization of deformation in the irradiated specimens, however, severity of localized deformation in AM steel, measured in dislocation channel spacing and height, was similar or more severe to that found in wrought. In conclusion, the presence of severe cracking in the wrought specimens did not allow for a direct comparison of localized deformation severities between the AM and wrought steel.

Additive manufacturing↗
DOE OSTI2019

TUNABLE EOS MATERIAL MODEL IN THE SIMULATION OF PULSED MERCURY SPALLATION TARGET VESSEL

A pulsed spallation target is subjected to very short (~1μs) but intense loads from repeated proton pulses. The effect of this pulsed loading on the stainless-steel target module which contains the flowing mercury target material is difficult to predict. Different simulation approaches and material models for the mercury have been tried. To date the best match of simulation results to experimental data was obtained with an equation of state (EOS) material model with a specified tensile cutoff pressure which simulates the cavitation threshold [1]. The inclusion of a threshold to represent cavitation was a key parameter in achieving successful predictions of stress waves triggered by the high energy pulse striking the mercury and vessel. However, recent measurements of strain responses of target modules show that significant differences between the measured strain and the strain simulated with EOS mercury model still exist. These differences grow to irreconcilable values when non-condensable helium gas is intentionally injected into the flowing mercury. A novel EOS mercury model embedded into ABAQUS VUMAT has been investigated in this project, which introduces the concept of proportional, integral, and derivative (PID) control into the mercury EOS model. By tuning the new introduced PID parameters (Kp, Ki and Kd), we replace the specified cutoff pressure with an adjustable spring-damper-like material behavior which may better match the complex dynamics of the mercury and helium mixture. This approach is expected to reduce the gap between measured and simulated vessel strain responses. Primitive application of this tunable EOS mercury model on prototypic shape experimental target has shown its capability and potentiality of improving mechanical behaviors of EOS mercury with cutoff pressure considered.

Lin, Lianshan↗
DOE OSTI2021

Evaluating the grain-scale deformation behavior of a single-phase FCC high entropy alloy using synchrotron high energy diffraction microscopy

We report although the deformation behavior of high-entropy alloys (HEAs) has been extensively studied at the macroscale, many important properties have yet to be explored for these alloys at the microscale, thus hampering accurate prediction of damage and failure processes. Synchrotron high-energy diffraction microscopy (HEDM) and fast-Fourier transform-based crystal plasticity modeling was conducted to investigate the three-dimensional (3D) grain-resolved micromechanical response for approximately 1,900 constituent grains within a single-phase FCC HEA up to 1% applied strain. The evolution of grain-resolved elastic strains, lattice reorientations, and maximum resolved shear stresses (mRSS) were evaluated to quantify elastic, yield, and fully plastic behavior. Overall, the initial critical resolved shear stress (CRSS), determined via in situ HEDM and companion modeling, was found to be > 20% higher than estimated using the classical polycrystalline Taylor factor (M = 3.06). However, a descriptive parameter based on the average grain-resolved Taylor factor ($\overline{M}$) was found to show excellent agreement with plastic yielding behavior observed within HEDM datasets. Noticeable deviations in HEDM lattice reorientations compared to both EVP-FFT simulations and classical predictions for FCC polycrystals were discovered, highlighting the complexity in correlating local lattice reorientations, Taylor, and Schmid factors with plastic response for this material at the grain-scale. Therefore, it is anticipated that the overall trends and parameter identification of 3D grain-resolved properties in this study can serve as an important foundation for continued mesoscale investigation on both well-established and newly developed Cantor-like HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

X-ray and Neutron Radiography for Quantitative Material Reconstructions

Radiography is a powerful tool to determine the interior structure of objects. X-ray radiography is widely used and provides high-resolution images, though X-rays have limited transmission through materials of high atomic number (Z) and density. In contrast, neutrons can penetrate many materials that are heavily attenuating to X-rays, such as metals, providing contrast in the inner layers of highly attenuating items. Past work has shown the value in using both X-ray and neutron radiography for estimating material thicknesses, though that work was limited to simulated data. Here, we demonstrate quantitative material reconstructions using experimental X-ray and neutron radiography data from lab-based systems, accurately modeling radiography system responses to within a few percent to enable quantitative measures of material thickness. We demonstrate the utility of neutron radiography and X-ray radiography for these quantitative reconstructions and introduce methods for using their complementarity to improve image quality and optimize experimental design.

Gilbert, Andrew J.↗
DOE OSTI2024

Extension of SCALE/Sampler’s sensitivity index for the assessment of cross section, fission yield, and decay data uncertainties

Accurate prediction of nuclide compositions and neutron and gamma sources and spectra for fresh and spent nuclear fuel through computational modeling and simulations is the basis for safeguards instruments design, optimization, and calibration, and for validation of the measured responses. The accuracy of these simulations can be significantly impacted by uncertainties in input parameters to the applied computer code. Input parameters are, for example, dimensions, material compositions, and temperatures of the model. Additionally, important but sometimes neglected input parameters for simulations of nuclear systems are the nuclear data that include nuclear reaction cross sections, fission product yields, and decay data. It has been shown that uncertainties of calculated results are dominated by uncertainties of these nuclear data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1992

An experiment on the use of disposable plastics as a reinforcement in concrete beams

Illustrated here is the concept of reinforced concrete structures by the use of computer simulation and an inexpensive hands-on design experiment. The students in our construction management program use disposable plastic as a reinforcement to demonstrate their understanding of reinforced concrete and prestressed concrete beams. The plastics used for such an experiment vary from plastic bottles to steel reinforced auto tires. This experiment will show the extent to which plastic reinforcement increases the strength of a concrete beam. The procedure of using such throw-away plastics in an experiment to explain the interaction between the reinforcement material and concrete, and a comparison of the test results for using different types of waste plastics are discussed. A computer analysis to simulate the structural response is used to compare the test results and to understand the analytical background of reinforced concrete design. This interaction of using computers to analyze structures and to relate the output results with real experimentation is found to be a very useful method for teaching a math-based analytical subject to our non-engineering students.

Chowdhury, Mostafiz R.↗
NASA NTRS1993

Multi-disciplinary coupling effects for integrated design of propulsion systems

Effective computational simulation procedures are described for modeling the inherent multi-disciplinary interactions which govern the accurate response of propulsion systems. Results are presented for propulsion system responses including multi-disciplinary coupling effects using coupled multi-discipline thermal, structural, and acoustic tailoring; an integrated system of multi-disciplinary simulators; coupled material behavior/fabrication process tailoring; sensitivities using a probabilistic simulator; and coupled materials, structures, fracture, and probabilistic behavior simulator. The results demonstrate that superior designs can be achieved if the analysis/tailoring methods account for the multi-disciplinary coupling effects. The coupling across disciplines can be used to develop an integrated coupled multi-discipline numerical propulsion system simulator.

Chamis, C. C.↗
NASA NTRS2006

A Framework for Performing Multiscale Stochastic Progressive Failure Analysis of Composite Structures

A framework is presented that enables coupled multiscale analysis of composite structures. The recently developed, free, Finite Element Analysis - Micromechanics Analysis Code (FEAMAC) software couples the Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC) with ABAQUS to perform micromechanics based FEA such that the nonlinear composite material response at each integration point is modeled at each increment by MAC/GMC. As a result, the stochastic nature of fiber breakage in composites can be simulated through incorporation of an appropriate damage and failure model that operates within MAC/GMC on the level of the fiber. Results are presented for the progressive failure analysis of a titanium matrix composite tensile specimen that illustrate the power and utility of the framework and address the techniques needed to model the statistical nature of the problem properly. In particular, it is shown that incorporating fiber strength randomness on multiple scales improves the quality of the simulation by enabling failure at locations other than those associated with structural level stress risers.

Bednarcyk, Brett A.↗