Search NASA⌕ Search

SEARCH · Search NASA

Results for “oxygen doping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Large area silicon sheet by EFG

The influence of parameters such as CO2 concentration, gas flow patterns, quartz in the bulk melt, melt doping level and growth speed on ribbon properties was examined for 10 cm wide ribbon. Ribbon quality is optimized for ambient CO2 in argon concentrations in the range from 1000 to 5000 ppm. Cell performance degrades at CO2 concentrations above 5000 ppm and IR interstitial oxygen levels decrease. These experiments were done primarily at a growth speed of 3.5 cm/minute. Cartridge parameters influencing the ribbon thickness were studied and thickness uniformity at 200 micrometers (8 mils) has been improved. Growth stability at the target speed of 4.0 cm/minute was improved significantly.

Source record↗
DOE OSTI2025

Controlled phosphate doping into nanoscopic SiO 2 proton conducting membranes

This article describes a method to introduce phosphate (PO 4 ) into SiO 2 atomic layer deposition (ALD) films in a self-limiting fashion. The method involves the use of a less common phosphate precursor, trimethyl phosphite [P(OMe) 3 ], to introduce PO 4 as a low-level dopant, <1 at. %, into a SiO 2 ALD process using bis(ethylmethylamino)silane and a modified O 3 conversion. P(OMe) 3 does not deposit a film with typical oxygen sources but incorporates as PO 4 in an ABC-type ALD scheme at deposition temperatures ranging from 100 to 300 °C. Addition of up to ∼1 at. % of PO 4 does not significantly impact the film density or concentrations of carbon and nitrogen impurities, which are both <0.4 at. %. Despite the relatively low dopant concentrations, PO 4 incorporation is shown to have a large impact on transport properties of the film. When explored as proton (H + )-conducting membranes, undoped SiO 2 ALD films showed H + conductivities (3 × 10 −6 –8 × 10 −5 S cm −1 ) and low H 2 permeabilities (<10 −9 cm 2 s −1 ) when measured at room temperature. The addition of PO 4 is shown to increase H + conductivity to 2 × 10 −4 S cm −1 , while maintaining low H 2 permeability of <10 −9 cm 2 s −1 . The ratio of H + conductivity to H 2 permeability, a key performance metric for H + -conducting membranes used in water electrolyzers, exceeds that of commercial Nafion-117 membranes. Here, the moderate H + conductivity and very low H 2 permeability of PO 4 -doped SiO 2 films make them promising candidates as fluorine-free replacements for Nafion in applications such as water electrolysis, hydrogen fuel cells, and redox flow batteries.

Atomic layer deposition↗
DOE OSTI2022

Electron-hole symmetry in quasiparticle spectral weight of cuprates observed via infrared and photoemission spectroscopy

Here we performed an optical spectroscopy study of single crystals of Pr 0.85 LaCe 0.15 CuO 4–δ (PLCCO) to revisit the electron-hole asymmetry, which has been understood as a fundamental property of cuprates. Four differently annealed samples—as-grown, reduced, optimally oxygenated, and overoxygenated samples—were prepared, which have superconducting transition temperatures T c = 0, 15, 24, and 18 K, respectively. We observed that the low-energy quasiparticle spectral weights of all the PLCCO samples are significantly small in comparison with those of other electron-doped cuprate families. Instead, they are rather close to those of their hole-doped counterpart La 2–x Sr x CuO 4 . Accordingly, estimated effective carrier numbers N eff per Cu atom of superconducting samples are also very small, despite their relatively high critical temperatures. A complementary photoemission study reveals that the low-energy quasiparticle spectral weight of PLCCO is much smaller than that of Nd 1.85 Ce 0.15 CuO 4–δ , consistent with the optical results. Our observations demonstrate that PLCCO provides the electron-hole symmetry in the quasiparticle spectral weight and highlight the importance of Cu 3d–O 2p hybridization to understand the low-energy spectral weight transfer in doped cuprates.

36 MATERIALS SCIENCE↗
DOE OSTI2026

SiC Substrate Composition Effect on TGO Scale Growth in EBC Systems During High‐Temperature Steam Exposure

A systematic investigation was conducted on the oxidation behavior of silicon-bond coats within environmental barrier coating (EBC) systems applied to Si-carbide (SiC) substrates, aiming to understand how different underlying SiC substrates influence the bond coat's thermally grown oxide (TGO) and its properties. The study examined (Y/Yb) 2 Si 2 O 7 /Si coatings on three cost-effective surrogate SiC substrates (chemical vapor deposition [CVD]-grown β-SiC, sintered α-SiC, and reaction-bonded [RB] SiC) for SiC fiber /SiC matrix ceramic matrix composites (CMCs). Discrepancies in TGO growth were observed, with noticeably higher growth rates reported for the coated CMC specimens than for the four monolithic SiC specimens. The CMC samples produce an amorphous TGO, whereas the other monolithic substrates formed a crystalline TGO, which lowered the oxygen permeability through the SiO 2 scale. In conclusion, the vitrification of the TGO in the (Y/Yb) 2 Si 2 O 7 /Si/CMC system resulted from the migration of boron species from the CMC substrate to the SiO 2 scale, leading to network modification via boron doping.

EBC↗
NASA NTRS2007

POSS(Registered TradeMark) Coatings for Solar Cells: An Update

Presently, solar cells are covered with Ce-doped microsheet cover glasses that are attached with Dow Corning DC 93-500 silicone adhesive. Various antireflection coatings are often applied to the cover glass to increase cell performance. This general approach has been used from the beginning of space exploration. However, it is expensive and time consuming. Furthermore, as the voltage of solar arrays increases, significant arcing has occurred in solar arrays, leading to loss of satellite power. The cause has been traced to differential voltages between strings and the close spacing between them with no insulation covering the edges of the solar cells. In addition, this problem could be ameliorated if the cover glass extended over the edges of the cell, but this would impact packing density. An alternative idea that might solve all these issues and be less expensive and more protective is to develop a coating that could be applied over the entire array. Such a coating must be resistant to atomic oxygen for low earth orbits below about 700 km, it must be resistant to ultraviolet radiation for all earth and near-sun orbits and, of course, it must withstand the damaging effects of space radiation. Coating flexibility would be an additional advantage. Based on past experience, one material that has many of the desired attributes of a universal protective coating is the Dow Corning DC 93-500. Of all the potential optical plastics, it appears to be the most suitable for use in space. As noted above, DC 93-500 has been extensively used to attach cover glasses to crystalline solar cells and has worked exceptionally well over the years. It is flexible and generally resistant to electrons, protons and ultraviolet (UV and VUV) radiation; although a VUV-rejection coating or VUV-absorbing ceria-doped cover glass may be required for long mission durations. It can also be applied in a thin coating (< 25 m) by conventional liquid coating processes. Unfortunately, when exposed to atomic oxygen (AO) DC 93-500 develops a frosty surface. Such frosting can lead to a loss of light transmitted into the cells and destroy the essential clarity needed for a concentrator lens.

Brandhorst, Henry↗
DOE OSTI2025

Plasmonic Ag nanocomposite phosphate glasses produced via γ-ray irradiation as reduction route

This paper reports on the impact of γ-ray irradiation (10, 100 kGy) on melt-quenched Ag + -doped phosphate glass and the effects of subsequent thermal processing leading to the production of plasmonic Ag nanocomposites. The γ-irradiated glasses were characterized alongside the pristine by differential scanning calorimetry (DSC), Raman spectroscopy, electron paramagnetic resonance (EPR) spectroscopy, optical absorption, and photoluminescence (PL) spectroscopy. DSC characterization showed consistent glass transition temperatures (T g ) before and after γ-irradiation whereas the crystallization temperatures tended to decrease with increasing γ-ray dose. However, a lack of alteration of the glass network structure was supported by Raman spectroscopy. Room temperature EPR spectra clearly showed the formation of phosphorus oxygen hole center (POHC) defects in the undoped host, in addition to another doublet likely associated with a P 3 defect. The presence of paramagnetic silver species encompassing Ag 2+ and 107/109 Ag 0 atoms was also indicated in the silver-activated glass together with POHC defects. Optical absorption spectra were also consistent with the presence of various radiation-induced centers. Further analyzing the glass absorption edge via Tauc plots suggested the formation of electron center (EC) defects in γ-irradiated samples wherein the silver-doped glass exhibited decreasing band gap energies with increasing γ-ray dose. The PL characterization showed the silver-related radio-PL effect was induced exhibiting broad band emission with two maxima around 500 and 625 nm stemming from various molecular Ag$^{x+}_{n}$ clusters. Emission decay analyses revealed that the longer wavelength emission exhibited slower decay. The highest radiation dose of 100 kGy however resulted in weaker emission and faster decay kinetics attributed to energy transfer between the luminescent silver species and POHC defects. Finally subjecting the γ-irradiated Ag-doped glasses to heat treatment near the T g at 490 °C led to the development of the surface plasmon resonance of Ag nanoparticles (NPs) and the vanishing of the Ag$^{x+}_{n}$ clusters luminescence. In conclusion, the presence of the matrix-related EC defects was deemed accountable for the thermally induced reduction and consequent precipitation of Ag NPs making the plasmonic glasses attractive for photonic applications such as nonlinear optics.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Enhancement of Ni–(Y 2 O 3 ) 0.08 (ZrO 2 ) 0.92 fuel electrode performance by infiltration of Ce 0.8 Gd 0.2 O 2–δ nanoparticles

This paper addresses the use of Ce 0.8 Gd 0.2 O 2–δ (GDC) infiltration into the Ni–(Y 2 O 3 ) 0.08 (ZrO 2 ) 0.92 (YSZ) fuel electrode of solid oxide cells (SOCs) for improving their electrochemical performance in fuel cell and electrolysis operation. Although doped ceria infiltration into Ni–YSZ has recently been shown to improve the electrode performance and stability, the mechanisms defining how GDC impacts electrochemical characteristics are not fully delineated. Furthermore, the electrochemical characteristics have not yet been determined over the full range of conditions normally encountered in fuel cell and electrolysis operation. Here we present a study of both symmetric and full cells aimed at understanding the electrochemical mechanisms of GDC-modified Ni–YSZ over a wide range of fuel compositions and temperatures. Single-step GDC infiltration at an appropriate loading substantially reduced the polarization resistance of Ni–YSZ electrodes in electrolyte-supported cells, as measured using electrochemical impedance spectroscopy (EIS) at various temperatures (600–800 °C) in a range of H 2 O–H 2 mixtures (3–90 vol% H 2 O). Fuel-electrode-supported cells had significant concentration polarization due to the thick Ni–YSZ supports. Here, a distribution of relaxation times approach is used to develop a physically-based electrochemical model; the results show that GDC reduces the reaction resistance associated with three-phase boundaries, but also appears to improve oxygen transport in the electrode. Increasing the H 2 O fraction in the H 2 –H 2 O fuel mixture reduced both the three-phase boundary resistance and the gas diffusion resistance for Ni–YSZ; with GDC infiltration, the electrode resistance showed less variation with fuel composition. GDC infiltration improved the performance of fuel-electrode-supported full cells, which yielded a maximum power density of 2.28 W cm –2 in fuel cell mode and an electrolysis current density at 1.3 V of 2.22 A cm –2 , both at 800°C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Tailoring activity of iron phthalocyanine by edge-nitrogen sites induced electronic delocalization

Fe-N-C catalysts have been recognized as the most satisfactory candidates alternatively to Pt-based catalysts for oxygen reduction reaction (ORR). However, fine-tailoring of their intrinsic ORR catalytic activity still remains a great challenge due to the inferior accessibility and intrinsic activity of FeN x moieties. Herein, one order of magnitude activity enhancement of pristine Fe-N-C through cooperating with nitrogen-doped carbon micro-flower is achieved. The axial coordination effect between Fe active center and nitrogen atoms in support can break the electronic distribution symmetry of FeN x moieties and induce the electron delocalization on Fe active center and the electron localization on N, respectively, which favor the adsorption behavior of *OH intermediate. As a result, the catalyst exhibits a remarkable half-wave potential of 0.9 V and a high kinetic current density of 74.04 mA cm -2 at 0.85 V. In addition, when utilized as a cathode catalyst of liquid Zn-air batteries (ZABs), it possesses excellent electrochemical performance, for example, a high open circuit voltage (OCV) and peak power density of 1.59 V and 170.09 mW cm -2 , respectively. In conclusion, this work provides a new understanding into the activity enhancement mechanism of Fe-N-C catalysts, and inspires electronic delocalization of active sites for adjusting catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The role of water vapor during the synthesis of hydrogen doped In 2 O 3

Hydrogen-doped In 2 O 3 synthesized using magnetron sputtering or atomic layer deposition in the presence of water vapor has high transparency in the near infra-red region and mobility values that are almost three to four times of those in commercially used In 2 O 3 :Sn at a much lower carrier concentration. However, simple questions like what happens when water molecules enter In 2 O 3 or why the dominant charge carrier changes from an oxygen vacancy in In 2 O 3 :Sn to H + in In 2 O 3 are not clear. Using hybrid functional based density functional theory calculations, in this study we show that water molecules spontaneously split into H + and OH – . The H + interstitial bonds with an oxygen in In 2 O 3 , and the OH – interstitial occupies a vacant lattice site or is trapped by an oxygen vacancy. Thus, in agreement with experimental findings, our results suggest that the concentration of oxygen vacancies decreases as the partial pressure of water increases. The charge transition level, ϵ ( – / + ) , of a hydrogen interstitial and the Fermi level at which the formation energies of OH – and H + are equal lie above the conduction band minimum, suggesting that the H + interstitial has a lower formation energy. In addition, water molecules do not exhibit any propensity to form clusters, meaning that H + ions can diffuse and remain spatially separated from each other.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Recombination luminescence from electron-irradiated Li-diffused Si

Lithium doping has a dramatic effect on the low-temperature photoluminescence of electron-irradiated Si. In oxigen-lean Si with Li doping, a new irradiation-dependent luminescence band between 0.75 and 1.05 eV is observed, which is dominated by a zero-phonon peak at 1.045 eV. This band is believed to be due to radiative transitions involving a Li-modified divacancy. This band is present also in oxygen-rich, Li-diffused Si and is accompanied by bands previously related to the Si-G15(K) center and the divacancy. The intensities of the Li-modified divacancy and Si-G15(K) center bands are relatively weak in the oxygen-rich material, apparently due to the formation of lithium-oxygen complexes which reduce the concentration of unassociated interstitial Li and O.

Johnson, E. S.↗
DOE OSTI2020

Experimental and theoretical study of the soot-forming tendencies of furans as potential biofuels

Sustainably-produced biofuels, including furans derived from lignocellulosic biomass, are being studied as potential next-generation fuels. Biofuels have unique structures that are absent in conventional fuels and they potentially emit fewer particulates than conventional fuels because of the presence of oxygen atoms. In this work, we focus on quantification and measurement of sooting tendency. A set of furans was selected and their sooting tendencies were characterized by Yield Sooting Index (YSI), which was obtained by measuring the line-of-sight spectral radiance (LSSR) of a coflow laminar diffusion flame doped with 1000 ppm of each test fuel. The measured YSIs are lower than traditional gasoline fuels and benzenoid aromatics (e.g., YSIbenzene = 100). We also performed numerical simulations with a detailed chemical kinetic mechanism to analyze the flame chemistry of 2-methylfuran (2MF). 4→5 H-atom migration in the furan ring causes 31.0% of the total decomposition and is the dominant fuel consumption pathway leading to soot. DFT calculations via the G4 composite method were carried out to obtain activation energies (Ea) and bond dissociation energies (BDE). The results showed that the 4→5 H-atom migration in the furan ring has the second lowest Ea and subsequently forms a 1,2-diene-substituted ketone derivative as a stable species. The ring-opening products of the 4→5 H-atom migration are propyne + a linear ketene for 2-n-alkylfurans, and 1-butyne + a methyl-substituted ketene for 2-t-butylfuran. These results can explain the trends of the measured YSIs of 2-alkylfurans.

09 BIOMASS FUELS↗
DOE OSTI2021

Binary Atomically Dispersed Metal-Site Catalysts with Core–Shell Nanostructures for O 2 and CO 2 Reduction Reactions

Engineering atomically dispersed metal site catalysts with controlled local coordination environments and 3D nanostructures effectively improves the catalytic performance for the oxygen reduction reaction (ORR) and the carbon dioxide reduction reaction (CO 2 RR), which are critical for clean energy conversion and chemical production. Herein, an innovative approach for preparing core-shell nanostructured catalysts with different single-metal sites in the core and the shell, respectively, is developed. In particular, as the shell precursors, covalent organic polymers with a thin layered structure that is polymerized in situ and coated on a metal-doped ZIF-derived carbon core are used, followed by a controlled thermal activation. The selective combination and construction of different metal sites increase active site density in the surface layers, promote structural robustness, facilitate mass/charge transfer, and yield a possible synergy of active sites in the core and the shell. The p-FeNC(shell)@CoNC(core), consisting of a polymerized FeTPPCl-derived carbon layer (p-FeNC) on a Co-doped ZIF-derived carbon (CoNC), exhibits remarkable ORR activity and stability in acidic media along with encouraging durability in H 2 –air fuel cells. Likewise, a p-FeNC(shell)@NiNC(core) catalyst demonstrates outstanding CO 2 RR activity and stability. Hence, integrating two appropriate single-metal sites in core and shell precursors, respectively, can modulate morphological and catalytic properties for a possible synergy toward different electrocatalysis processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1993

Transition metals in superheat melts

A series of experiments with silicate melts doped with transition element oxides was carried out at atmospheric pressures of inert gas at temperatures exceeding liquidus. As predicted from the shape of fO2 buffer curves in T-fO2 diagrams the reducing conditions for a particular oxide-metal pair can be achieved through the T increase if the released oxygen is continuously removed. Experimental studies suggest that transition metals such as Cr or V behave as siderophile elements at temperatures exceeding liquidus temperatures if the system is not buffered by the presence of other oxide of more siderophile element. For example the presence of FeO prevents the reduction of Cr2O3. The sequence of decreasing siderophility of transition elements at superheat conditions (Mo, Ni, Fe, Cr) matches the decreasing degree of depletion of siderophile elements in mantle rocks as compared to chondrites.

Jakes, Petr↗
DOE OSTI2020

Keratin-derived functional carbon with superior charge storage and transport for high-performance supercapacitors

In this work, we report a scalable method to synthesize hierarchically porous, hetero-atom doped activated carbon nanosheet from waste biomass-human hair, and demonstrates the use of this carbon as an ultra-high performance electrode material for supercapacitor applications. Microscopic analyses reveal that sheet size ranges from 50 to 200 nm having a thickness of 15–27 nm. As-synthesized, carbon nanosheets possess a hierarchical porous structure having a specific surface area of 1548 m 2 g -1 . Heteroatom concentration (nitrogen, oxygen, and sulfur) of around 25% is confirmed from XPS analysis. Therefore, the novel interconnected hierarchical porous nanosheets structure enables fast adsorption and transportation of ions during electrochemical processes. Also, the abundant chemically available electroactive heteroatom species in the material enhance the wettability of ions and contribute to pseudocapacitance. The electrochemical analyses through cyclic voltammetry and galvanostatic charge-discharge measurements in 6 M KOH reveal the quasi-EDLC behavior of the activated carbons due to the presence of heteroatoms. A reprensentative KOH activated carbon shows an excellent specific capacitance value of 999 F g -1 at a current density of 1 A g -1 . Furthermore, the symmetrically assembled two-electrode device also delivers a maximum energy density of 32 W h Kg -1 at a power density of 325 W Kg -1 . In addition, excellent cyclic stability of 98% capacitance retention is observed after 10,000 continuous GCD cycles even at a high current density of 5 A g -1 . Symmetric flexible supercapacitor device using KOH-PVA-K3FeCN6 as redox gel polymer electrolyte shows a synergistic specific capacitance of 145 mF cm -1 at a current density of 0.8 mA cm -1 exhibiting very less deviation in bending mode. Therefore, this waste biomass derived heteroatom doped hierarchical porous carbon nanosheets can be a promising material for cost-effective high- performance supercapacitor.

42 ENGINEERING↗
DOE OSTI2020

Chemical Vapor Deposition for Atomically Dispersed and Nitrogen Coordinated Single Metal Site Catalysts

Abstract Atomically dispersed and nitrogen coordinated single metal sites (M‐N‐C, M=Fe, Co, Ni, Mn) are the popular platinum group‐metal (PGM)‐free catalysts for many electrochemical reactions. Traditional wet‐chemistry catalyst synthesis often requires complex procedures with unsatisfied reproducibility and scalability. Here, we report a facile chemical vapor deposition (CVD) strategy to synthesize the promising M‐N‐C catalysts. The deposition of gaseous 2‐methylimidazole onto M‐doped ZnO substrates, followed by an in situ thermal activation, effectively generated single metal sites well dispersed into porous carbon. In particular, an optimal CVD‐derived Fe‐N‐C catalyst exclusively contains atomically dispersed FeN 4 sites with increased Fe loading relative to other catalysts from wet‐chemistry synthesis. The catalyst exhibited outstanding oxygen‐reduction activity in acidic electrolytes, which was further studied in proton‐exchange membrane fuel cells with encouraging performance.

Liu, Shengwen↗
DOE OSTI2024

Orienting Strained Interfaces designed to Direct Energy Flow (Final Technical Report)

This proposal aims to establish a transformative paradigm for oxide heterostructures with an exceptionally large number of interfaces designed to direct energy flow through controlled interface orientation, enabling fast ion transport. A primary focus is on unveiling the key role of interfacial strain in oxygen ion migration at low temperatures. The central challenge is to create, understand, utilize self-assembled vertical heteroepitaxial nanostructures with the goal of obtaining and understanding fast ion transport properties by modulating interfacial strain. The specific objectives are: (1) to synthesize multilayer thin films and vertical heteroepitaxial nanostructures with fluorite Gd-doped CeO 2 (GDC) and bixbyite RE 2 O 3 (RE = Y and Sm), (2) to evaluate the interfacial strain states under various temperatures and ambient conditions, (3) to understand the effect of interfacial strain on ionic conductivity of the proposed nanostructures, (4) to understand the three-dimensional (3D) atomic structure of the proposed material design and interface phenomena at the atomic scale.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Photocatalytic degradation of orange II dye via high pore volume polymorph zirconium-doped titania under visible light irradiation

A series of mixed-phase Zr-doped TiO 2 was utilized for the photocatalytic degradation of orange II dye. These materials were synthesized through a sol–gel technique by varying the amounts of zirconium in the photocatalysts. These materials were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray fluorescence (XRF), Raman spectroscopy, thermogravimetry analysis (TGA), and X-ray photoelectron spectroscopy (XPS) among others. XRF and XPS data showed that the elemental composition of the photocatalysts consists of zirconium, titanium, and oxygen. In addition, XRD and Raman spectroscopy confirmed the existence of anatase and rutile phases of TiO 2 . The TGA analyses showed that the undoped TiO 2 was the most stable, with no significant weight loss during the heating range. Furthermore, the materials can effectively degrade orange II dye solution up to 7 cycles through asymmetric cleavage of the azo bond.

36 MATERIALS SCIENCE↗