Search NASA⌕ Search

SEARCH · Search NASA

Results for “post processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

UV-Induced Degradation and Associated Metastability in TOPCon Photovoltaic Modules: Understanding Kinetics and Cell Variance

Tunnel oxide passivated contact (TOPCon) silicon photovoltaic (PV) modules are dominating the PV market, but they may be susceptible to degradation under ultraviolet (UV)-containing light. Quantifying the impacts of UV-induced degradation (UVID) is complicated by an associated metastability causing further degradation under dark storage and rapid recovery under sunlight. Here, we study modules that have -2.3% to -3.2% nonrecoverable UVID loss after 60 kWh/m2 dose of 340 nm light and additional recoverable loss under dark storage. We use in situ electroluminescence (EL) imaging to characterize the post-UVID metastability at the module level. The cell-by-cell dark degradation and recovery kinetics span a wide range from +6% to -70% changes in EL intensity after 520 h of dark storage, which returns to +- 4% of the initial post-UVID EL intensity after illumination. The kinetics follow double exponential rates with dark storage degradation time constants of 345 and 45 h, and UV light recovery time constants of 5 min and 36 s. We propose that this is consistent with prior reports of kinetics for light-soaking metastability in Al2O3 passivation. Finally, we further show that cells having high UVID also have injection-dependent effective carrier lifetimes and significant intra-cell variance, suggesting possible origins of processing inconsistency.

14 SOLAR ENERGY↗
DOE OSTI2025

Conceptual Model Testing Related to SDU 6 Drainwell Observations

From its inception in the early 1950s through the end of the Cold War in the early 1990s, the Savannah River Site (SRS) produced nuclear materials for national defense in five reactors. Additionally, irradiated reactor fuel and target tubes were dissolved in nitric acid to recover plutonium and uranium using the PUREX (Plutonium Uranium Reduction EXtraction) process. Liquid waste from these chemical separations processes was then stored onsite in 51 underground tanks. Eight waste storage tanks have been operationally closed (i.e. cleaned and grouted) and the remaining tanks hold a mixture of liquids, insoluble solids, and precipitated salts (SRMC-LWP-2022-00001), the latter generated by evaporating water from the liquid waste. Waste is currently being retrieved from tanks and separated into 1) high-radioactivity, low-volume, and 2) low-radioactivity, high-volume components, principally through the Salt Waste Processing Facility (SWPF) (SRMC-LWP-2023-00001). The former waste stream is vitrified in the Defense Waste Processing Facility (DWPF), stored onsite, and destined for offsite disposal in a deep geologic repository. The latter stream is mixed with dry cementitious materials in the Saltstone Production Facility (SPF) and the wet slurry placed in onsite Saltstone Disposal Units (SDUs) within the Saltstone Disposal Facility (SDF), where it hardens into a cement waste form termed saltstone. A low-infiltration surface cover system will be placed over the SDF at closure, where SDUs will then be in the subsurface post-closure (SRR-CWDA-2019-00001).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Pivotal role of organic adsorbates for the creation of catalytic sites during dry reforming of methane

Inadvertent factors can sometimes be crucial for synthesis of catalysts. The use of polyalcohols is common in the synthesis of heterogeneous catalysts. Interactions between alcohols and heterogeneous catalysts have been shown to induce surface reconstructions that greatly impact catalytic performance. Thus, traces of these alcohol functionalities on the as-synthesized catalysts, combined with heat treatment, could be critical in the generation of catalytic sites. Here, we show that during the synthesis of a Ni–Mo/MgO catalyst using a polyol process, residual ethylene glycol (EG) on the surface plays a significant role in the generation of catalytic sites for dry reforming of methane (DRM). The as-synthesized catalyst presents dispersed cationic Ni. Under DRM reaction conditions, the presence of EG, and H2 generated in situ, promote the generation of co-localized Ni–Mo nanoparticles (NPs). Greater amount of EG in the as-synthesized catalyst prevented sintering, leading to better catalyst stability and higher rates. If the residual EG remaining post-synthesis is removed through calcination, before conducting DRM, NiO NPs are formed and the material is completely inactive for catalyzing the reaction. When using a different support, denoted MgO*, EG also proved indispensable to generate active sites, although Ni–Mo co-localization was not evident, and a combination of DRM-related species was needed to activate the catalyst, not just H2. This work systematically uncovers how the interactions between organic adsorbates, the supported metals and the catalyst support dictate the creation of catalytic active sites.

Polo Garzon, Felipe [ORNL] (ORCID:0000000265076183↗
DOE OSTI2026

Flash electropolishing for TEM: Reducing FIB‐induced defects in tungsten with protocols for new materials

Focused ion beam (FIB) milling has become the dominant approach for site-specific transmission electron microscopy (TEM) specimen preparation; however, FIB damage remains a critical limitation for reliable microstructural characterisation, particularly in radiation effects studies. Tungsten is especially susceptible to FIB damage due to its high nuclear stopping power, which promotes the formation and strong diffraction contrast of FIB-induced ‘black spot’ defects that are indistinguishable from very fine irradiation-induced loops/defects resulting from low to intermediate temperature neutron irradiation. In this work, flash electropolishing is systematically evaluated as a post-FIB treatment for minimising preparation-induced artefacts for TEM analysis of tungsten-based alloys. Using a range of non-, ion-, and neutron-irradiated tungsten materials, the effectiveness of flash electropolishing has been assessed through direct comparison with conventional FIB and plasma-FIB preparation including low-energy Ga, Ar, Xe ion cleaning. The results demonstrate that flash electropolishing effectively removes FIB-damaged layers and ‘black spot’ defects, thereby enabling reliable observation of irradiation-induced dislocation structures. Key processing parameters governing flash electropolishing quality – including lamella thickness, applied voltage, polishing duration, electrolyte chemistry, and cathode geometry – have been systematically evaluated, and clear criteria were established for determining when flash electropolishing is required to ensure reliable microstructural analysis. This work also provides practical guidance for implementing flash electropolishing as an artefact-controlled specimen-preparation approach for TEM characterisation of FIB-produced specimens. The systematic protocol can be extended to other, non-tungsten materials.

TEM sample preparation↗
DOE OSTI2026

Sintering effects on NpO 2 grain size and morphology: The role of precursor Np phase

Neptunium dioxide (NpO 2 ) is a key phase in nuclear material processing as a target material for the production of plutonium-238 ( 238 Pu) and has been historically synthesized via the calcination of a Np oxalate precursor. Alternative synthesis methods for NpO 2 are now more prevalent, necessitating their study and comparison with the more common oxalate route. The purpose of this work was to investigate the microstructural properties of NpO 2 synthesized from a nitrate-based Np precursor phase via the assessment of NpO 2 particle size and morphology as a function of calcination temperature and time. Scanning electron microscopy (SEM) was used to probe the primary grain size and morphology of NpO 2 after calcination at temperatures ranging from 700 to 1100 °C and hold times ranging from 1 to 10 h. Post-image analysis using ImageJ software enabled the quantification of mean particle diameter. This analysis indicated that particle diameter increases with both increasing calcination temperature and hold time. Primary particles were shown to be clumped in irregular patterns into the overall rough, blocky aggregates, but this macroscopic morphology was not affected by calcination time or temperature. Although trends in primary grain size of NpO 2 were consistent with available literature from other Np precursor phases, the macroscopic morphology of the NpO 2 aggregates was quite different than reported for other precursors. Through comparison with historical literature on Np oxalate, this work emphasizes the importance of Np precursor on the physical properties of NpO 2 .

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2025

Identification and evolution of active sites in isomorphously substituted Fe-ZSM-5 catalysts for methane dehydroaromatization (MDA)

Methane dehydroaromatization (MDA) enables the catalytic conversion of methane into aromatics, mainly benzene, along with hydrogen, in a single-step process under non-oxidative conditions. In this study, we prepared a series of isomorphously substituted Fe-ZSM-5 catalysts with exclusively isolated or low-oligomerized sites up to 3.2% Fe weight loading by adding ethylenediaminetetraacetic acid (EDTA) to the crystallization gel. These catalysts exhibit no induction/activation period and a significantly higher maximum product yield compared to Fe/ZSM-5 catalysts prepared by the incipient wetness impregnation method and containing extensively aggregated FeOx. This investigation focuses on the evolution of Fe sites during the post-synthetic treatments. Most importantly, we demonstrate the quantitative relation between Fe site isolation and catalytic activity, proving that isolated or low-oligomerized Fe species at the exchange sites formed during post-synthetic retreatment are the active sites for methane activation.

02 PETROLEUM↗
DOE OSTI2026

Dynamic compression and spallation behavior of NbTaTiVZr high-entropy alloy

High-entropy alloys are a new class of materials with promising properties for aerospace and defense applications. The unique behavior of these materials is driven by the complex interactions between dissimilar atoms in a crystal and requires combined theoretical and experimental efforts to unlock their full potential. Here, we evaluate the relationship between the microstructure and the dynamic response of the equiatomic NbTaTiVZr alloy. Specifically, the shock Hugoniot, or equation of state, was measured up to a particle velocity of 0.5 mm μs −1 using gas gun plate impacts. Shock wave profile and incipient spallation experiments were used to characterize wave propagation and damage formation with post-mortem recovery experiments. Molecular dynamics simulations confirm the experimental findings and extend them up to 2.1 mm μs −1 particle velocity. Computational thermodynamic calculation of phase diagram simulations explain details of the material microstructure, which explains the measured strength and experimental damage patterns. Overall, this work provides detailed high-strain-rate characterization of a refractory high-entropy alloy, and more importantly, a framework and demonstration of the utility and necessity of a combined theoretical and experimental approach, outlining the importance of considering processing and manufacturing conditions when evaluating the performance of new materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Computational Modeling of CO2 Capture By Novel PIM-RU in a Fluidized Bed Riser

The interest in carbon capture, storage, and utilization (CCUS) has increased significantly in the past few decades as it can help mitigate the threat of global warming caused by substantial increase in CO2 emissions due to anthropogenic activities. Although several CO2 capture technologies have been developed, porous solid sorbents, which adsorb CO2 by physisorption, are considered promising candidates for post-combustion CO2 capture because of the easier recovery of adsorbed CO2 and high material stability. Some prominent types of porous solid sorbents are metal-organic frameworks (MOFs), Zeolite, mesoporous silica, and polymer-based sorbents (e.g., polymers with intrinsic microporosity or PIM). Oak Ridge National Laboratory (ORNL) recently developed a novel PIM-based sorbent, referred to here as PIM-RU. The main objective of this work is to investigate the CO2 capture performance of this sorbent using computational fluid dynamics (CFD). While process configuration and reactor design are open questions, a fluidized bed riser was selected as the contactor type for this study.

Aziz, Hossain↗
DOE OSTI2024

Dualities among massive, partially massless and shift symmetric fields on (A)dS

We catalog all the electromagnetic-like dualities that exist between free dynamical bosonic fields of arbitrary symmetry type and mass on (anti-) de Sitter space in all dimensions, including dualities among the partially massless and shift symmetric fields. This generalizes to all these field types the well known fact that a massless p-form is dual to a massless (D − p − 2)-form in D spacetime dimensions. In the process, we describe the structure of the Weyl modules (the spaces of local operators linear in the fields and their derivative relations) for all the massive, partially massless and shift symmetric fields.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Degradation and Accelerated Recovery of Surface Passivation in n+ Poly-Si/SiOx Passivating Contacts for TOPCon Solar Cells

We studied the surface degradation and recovery of fired poly-Si/SiOx passivating contacts during subsequent dark and illuminated annealing. We report on an industrially-viable path for accelerated recovery of surface passivation. The degradation is influenced by the type of doping in the poly-Si. Phosphorus doped n+ poly-Si/SiOx contacts show degradation followed by recovery, undoped poly-Si/SiOx contacts only show recovery during annealing. Boron doped p+ poly-Si/SiOx contacts show neither degradation nor improvement with annealing. Both degradation and recovery are thermally-activated processes and are completely reversible and cyclic in nature. The activation energy of degradation and recovery in dark for n+ poly-Si/SiOx contacts are 1.27 and 1.33 eV respectively. Dark annealing at elevated temperatures is effective for complete recovery but takes a long time (~30 min at 350 degrees C) due to higher activation energies. Annealing under 7.5 Suns of illumination lowers the activation energy for degradation and recovery to 0.88 and 0.90 eV, respectively. Using this data, we have developed an industrially viable post-firing treatment for accelerated recovery of TOPCon cells by annealing them at elevated temperatures and under intense illumination for a few minutes.

14 SOLAR ENERGY↗
DOE OSTI2024

Machine learning models of intermittent operation of RO wellhead water treatment for salinity reduction and nitrate removal

Machine learning models were developed for intermittent multi-mode operation of a wellhead reverse osmosis water purification and desalination system to predict salt passage, nitrate passage, and permeate flux. The models, based on long short-term memory (LSTM) recurrent neural network (RNN) architecture, included an attention mechanism to increase model performance in proximity of the regulatory limit for nitrate. Training and testing of the models for the Startup, Production, Shutdown and Flushing operational modes were based on operational data (consisting of 22 process variables per data sample) acquired every 2–5 s over a six-month period. The significant sets of model input attributes for the different operational modes were assessed via Spearman ranking correlation, Self-Organizing Map (SOM) analysis and feed forward feature selection (FFFS). Although the variability of nitrate passage, salt passage and permeate flux was significant over the four operational modes, prediction performance for the three outcomes were with R2 and Average Absolute Relative Error (AARE) of 0.78–0.95 and 2.96–6.16 %, respectively. Model updates post membrane elements replacement demonstrated similar levels of prediction accuracy. The study results suggest that there is merit in exploring the utility of multi-mode models for sensor fault detection, data imputation, and for potential use in model-predictive control.

Intermittent RO operation↗
DOE OSTI2025

Immersive Scientific Visualization of Molten-Salt Reactor Waste Characteristics Using Virtual Reality

Immersive visualization is changing how we explore, communicate, and understand complex scientific systems. In nuclear energy, an area in which data are often multidimensional, time-dependent, and difficult to interpret, virtual reality (VR) represents a powerful and intuitive informational medium. This work introduces a VR-based platform that visualizes the post-shutdown behavior and waste management lifecycle of molten-salt reactors (MSRs), a next-generation reactor type with unique operational and safety characteristics. The platform, built in Unity, is streamed on the Meta Quest 3 headset. It transforms high-fidelity simulation data into an interactive, immersive experience. Users can explore time-dependent reactor characteristics such as nuclide decay, which is a key factor for evaluating reactor waste strategies. The datasets were generated using the MOOSE (Multiphysics Object-Oriented Simulation Environment) framework and then processed through ParaView scripting for smooth integration into Unity. From a visualization standpoint, the platform emphasizes spatial storytelling, temporal exploration, and user-centered interaction. Users can navigate 3D reactor geometries, slice through volumetric data, and manipulate time to observe how physical phenomena evolve. Real-scale rendering and embodied interaction make the experience feel tangible. The interface is designed to be accessible, even to those without nuclear or simulation expertise. This lowers the barrier for stakeholders, policymakers, and the general public, while still supporting expert analysis and collaborative decision-making. This work shows how immersive visualization can function as both a scientific tool and a communication interface. By integrating simulation, processing, and visualization into a cohesive workflow, we offer a scalable framework for immersive scientific storytelling. The modular design supports future extensions to other reactor types and lifecycle stages, from shutdown to long-term storage, making the platform adaptable for both research and outreach.

99 - GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Isotope exchange of ND 3 on Pt catalyst-loaded 13X molecular sieve

During D-T fusion operations the capture, purification, and recycling of unburned tritium will be crucial, as the formation of tritium containing molecules require additional processing. Here, removing the tritium can require costly processing to be unbound from the tritium-containing molecules and improvements to these processes will be necessary moving forward. Existing techniques using sorbent material beds to remove tritium-containing molecules from process gas streams undergo repeated high-heat cycling which leads to diminished bed lifespans, necessitating replacement and associated downtime. This work demonstrates the capture and isotopic exchange technique of deuterated ammonia (ND3), used as a surrogate for tritium, at ambient temperature using a Pt catalyst-loaded 13X molecular sieve. Unmodified 13X molecular sieve is capable of adsorbing and retaining the ND3 however, incorporation of a catalyst facilitates the isotopic exchange of the hydrogen isotopes. The effluent gas streams were analyzed in conjunction with desorbed ammonia isotopologues post-exchange to verify these results. Isotopically exchanging and removing heavier hydrogen isotopes using this technique provides an alternative to traditional removal methods.

08 HYDROGEN↗
DOE OSTI2025

Chromium enhances the mechanical performance of 3d transition metal high entropy alloys

A comprehensive examination of the compositional effects on the deformation behavior of high entropy alloys (HEAs) was conducted through nanoindentation, indentation creep, and stress relaxation experiments at ambient temperature. The alloys investigated included NiCoFe, NiCoCr, NiCoCrFe, and NiCoCrFeMn, all of which underwent identical thermomechanical processing. From the experimental results, NiCoCr exhibited the highest maximum shear stress for dislocation nucleation (13 GPa) and nanoindentation hardness (3.8 GPa) among the alloys tested. It also showed the lowest stress sensitivity (0.02) and activation volume (3–4 b 3 ) under creep and stress relaxation conditions, indicative of its superior plastic flow properties. Density functional theory (DFT) calculations further revealed an uneven charge density and larger bonding-length variation in NiCoCr due to the presence of Cr, which increased lattice distortion, impeding dislocation movement. Furthermore, in this study, post-deformation microscopy using transmission electron microscopy (TEM) revealed a high density of stacking faults and twins in NiCoCr that effectively enhanced its creep strength. The results highlight the significance of specific elemental effects, particularly from Cr in this study, over configurational entropy effect (i.e., compositional complexity) in governing the deformation microstructure and mechanical properties of HEAs. Finally, these insights will be instrumental for the design and optimization of advanced alloys for load-bearing applications.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Arsenic activation and compensation in single crystal CdTe bilayers

In state-of-the art polycrystalline CdTe photovoltaics, group-V dopant activation is about 2%. Low activation can create electronic defects and lead to recombination and band tail losses. To develop methods to overcome this limitation, dopant activation was systematically investigated using molecular beam epitaxy (MBE) grown single crystal bilayers of As-doped CdTe on undoped CdTe. Results suggest multiple paths for improved As-activation in polycrystalline CdTe-based devices. It was found that the carrier concentration in this MBE material saturated at ∼3 × 1016 cm−3, with high levels (>50%) of As-activation possible. High activation could be achieved with a post-growth activation temperature of ∼450 °C, when the initial doping level was below the saturation level. However, at typical polycrystalline As incorporation levels (>5 × 1016 cm−3), the excess As is inactive or compensating, requiring elevated temperatures (500–600 °C) to achieve high activation. Oxygen in the annealing ambient was detrimental, while the effect of CdCl2 in the ambient is more case-dependent. A 575 °C activation anneal was combined with a 450 °C CdCl2 treatment to better understand the implications for polycrystalline CdTe. Interestingly, on highly doped samples, processes ending with a high temperature step displayed high activation, while those ending at 450 °C significantly reduced the carrier concentration (with or without CdCl2 in the ambient). Low activation can be restored with another high temperature anneal, allowing reproducible toggling between high and low activation based on the final temperature. Photoluminescence revealed the presence of donor–acceptor pairs in the low activation state that appear to be associated with a compensating defect.

14 SOLAR ENERGY↗
DOE OSTI2024

Summary of Gas Generation Behavior Observed in 3013 Surveillance and Monitoring Program Shelf-Life Experiments

Gas generation experiments have been conducted in small- and full-scale test containers at Los Alamos National Laboratory on samples of plutonium oxide material collected from plutonium processes across the DOE complex and tested at the bounding conditions for the Department of Energy 3013 Standard. The gas composition and pressures in the sealed experimental containers were measured over periods of months to years. These experiments have provided results for the formation and consumption of hydrogen and other gases. The conditions supporting the formation of flammable gas mixtures of hydrogen and oxygen in flammable gas mixtures were also determined. Different behaviors were observed between the materials tested based on their compositions, the stabilization performed on the material, and the post stabilization handling of the material. Many of the experiments are still ongoing. This report summarizes the results obtained for the gas generation behavior for high-purity plutonium oxides and salt-bearing impure plutonium oxides in sealed containers.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Computational Analysis of the Effect of Structured Packing Design on Absorption Column Hydrodynamics for Post-Combustion Carbon Capture Applications

Solvent based post-combustion carbon capture technologies have a potential for reducing carbon emissions from fossil-fuel-fired power plants and industrial sources where CO2 emissions are inherently harder to mitigate, such as steel or cement industries. A prominent technology to achieve this is by retrofitting absorption columns to the existing infrastructure. While these systems have been among the less costly alternatives for carbon capture, they still impose a considerable energy penalty to the operation of power plants or industrial facilities. The optimization of CO2 capture rate in solvent-based absorption process is complex as it depends on several factors including CO2 solubility, solvent reaction kinetics and temperature effects on the solubility, reaction rates, surface tension, and thermophysical properties of the solvent and the flue gas. The overall heat and mass transfer also depends on the hydrodynamics, which in turn, is affected by the packing geometry. In the current work, we systematically quantify the effects the design of the structured packing has on the column hydrodynamics, by performing detailed CFD simulations for different geometrical configurations and operating conditions. We then obtain relationships between the key hydrodynamic metrics, such as liquid holdup, interfacial area, wetted area, and pressure drop to the parameters defining the packing geometries and identify new more effective packing designs for the given operating conditions.

Shah, Yash Girish↗
DOE OSTI2025

The impact of nickel concentration and stacking fault energy on deformation mechanisms in high-purity austenitic Fe-Cr-Ni alloys

Understanding how composition affects deformation mechanisms in austenitic stainless steels is essential for developing accurate predictive models of stress-induced failures and stress corrosion cracking. Nickel (Ni), an element classified as a critical element, plays a crucial role in these processes. It is important to examine how Ni concentration influences stacking fault energy (SFE) and, consequently, the deformation mechanisms of austenitic stainless steels. However, in commercial stainless steels, the effects of other alloying elements and impurities can obscure Ni's role, complicating efforts to isolate its impact. Here, in this study, we use two high-purity Fe-Cr-Ni alloys to investigate how Ni concentration and SFE interact to alter deformation mechanisms and induce martensitic transformation. By combining in situ synchrotron X-ray diffraction (XRD) tensile testing and post-mortem electron microscopy with density functional theory simulations, we gain precise insights into these phenomena. We find that the Fe18Cr10Ni (wt%) alloy, with its low SFE, exhibits higher stacking fault probability, deformation-induced martensitic transformation, and a lesser increase in dislocation density with plastic strain. In contrast, the Fe18Cr14Ni (wt%) alloy, with its higher SFE, shows enhanced deformation twinning and greater dislocation density with increasing strain. These findings from high-purity ternary alloys provide valuable insights that can guide the search for alternative elements to replace Ni while achieving similar effects on phase stability and deformation behavior.

36 MATERIALS SCIENCE↗