Search NASA⌕ Search

SEARCH · Search NASA

Results for “static testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

The dynamic tensile strength of ice and ice-silicate mixtures

The dynamic tensile strength of icy media is measured at strain rates on the order of 10,000/sec to aid in the understanding of impact and cratering phenomena. Compressed samples consisting of ice and ice-silicate mixtures with 5 and 30 wt % sand were impacted at temperatures between 230 and 250 K by projectile plexiglas plates imparting the required strain rates in less than 0.75 microsec. Taking the tensile stress corresponding to the transition from intact to spalled or fragmented samples as the dynamic tensile strength, strengths of 17, 20 and 22 MPa were obtained for the pure ice, 5 wt % sand, and 30 wt % sand specimens, respectively. The values lie considerably above those observed in static testing. A continuum fracturing model is used to obtain relations between tensile strength and stress rate as well as to derive stress and damage histories during tensile loading and the size distribution of icy fragments as a function of strain rate.

Lange, M. A.↗

A compact inflow control device for simulating flight fan noise

Inflow control device (ICD's) of various shapes and sizes have been used to simulate inflight fan tone noise during ground static tests. A small, simple inexpensive ICD design was optimized from previous design and fabrication techniques. This compact two-fan-diameter ICD exhibits satisfactory acoustic performance characteristics without causing noise attenuation or redirection. In addition, it generates no important new noise sources. Design and construction details of the compact ICD are discussed and acoustic performance test results are presented.

Homyak, L.↗

Analysis of progressive damage in thin circular laminates due to static-equivalent impact loads

Clamped circular graphite/epoxy plates (25.4, 38.1, and 50.8 mm radii) with an 8-ply quasi-isotropic layup were analyzed for static-equivalent impact loads using the minimum-total-potential-energy method and the von Karman strain-displacement equations. A step-by-step incremental transverse displacement procedure was used to calculate plate load and ply stresses. The ply failure region was calculated using the Tsai-Wu criterion. The corresponding failure modes (splitting and fiber failure) were determined using the maximum stress criteria. The first-failure mode was splitting and initiated first in the bottom ply. The splitting-failure thresholds were relatively low and tended to be lower for larger plates than for small plates. The splitting-damage region in each ply was elongated in its fiber direction; the bottom ply had the largest damage region. The calculated damage region for the 25.4-mm-radius plate agreed with limited static test results from the literature.

Shivakumar, K. N.↗

The effect of matrix properties and fiber properties on impact failure mechanics

The low-velocity impact problem in graphite/epoxy composite sheets must be solved before large amounts of that material can be used in commercial aircraft. Many of the low-velocity impacts that affect aircraft parts occur during normal ground operations and maintenance. Service equipment and tools have masses above 1 kg, and at velocities of less than 3 m/s can impact structural parts with energies higher than composites can endure without degradation of stiffness or strength. Simple solutions were developed for large-mass, low-velocity impacts which can be modeled as quasi-static events. Static test data and impact data show that the fiber properties control the impact energy which can be absorbed before penetration. Matrix shear strength and peel resistance control the extent of delamination. Comparison of results from tough matrix and brittle matrix composites show that although tough matrices reduce the extent of delamination, they lead to more fiber damage in the contact area.

Elber, W.↗

Analyses of processing variables in propellant burn rate and modulus. I - Mixing times

The effect of the final mixing time on quality of smokeless AP/HTPB propellant with bimodal AP was examined. Identical ingredients were mixed for various intervals, cast in a circular tube, then fired in a static test. Mechanical properties were measured and initial moduli were calculated from the initial slope of the S-N curves. A theoretical model was developed using the data to quantitatively configure a quality control procedure. A minimum time for mixing fine and coarse AP particles was identified and was approximated to within a factor of two or three using a viscous dispersion time and the surface areas of the particles. The model could be improved by considering settling time and particle size distribution effects.

Ramohalli, K.↗

Finite element-integral acoustic simulation of JT15D turbofan engine

An iterative finite element integral technique is used to predict the sound field radiated from the JT15D turbofan inlet. The sound field is divided into two regions: the sound field within and near the inlet which is computed using the finite element method and the radiation field beyond the inlet which is calculated using an integral solution technique. The velocity potential formulation of the acoustic wave equation was employed in the program. For some single mode JT15D data, the theory and experiment are in good agreement for the far field radiation pattern as well as suppressor attenuation. Also, the computer program is used to simulate flight effects that cannot be performed on a ground static test stand.

Baumeister, K. J.↗

Development of Gas-Lubricated Pistons for Heavy Duty Diesel Engine Technology Program

Static testing of a segmented, gas-lubricated, piston-ring was accomplished. The ring utilizes high-pressure gas generated during the diesel cycle to energize a hydrostatic gas film between the piston and cylinder liner. The configuration was deficient in overall performance, because all segments of a ring set failed to form a fluid-film simultaneously, when exposed to internal preload. The difficulty was traced to the moment balance required to prevent the segments from overturning and contacting the cylinder walls. Some individual sectors formed a film and performed well in every respect including load capability to 6,000 N. These results produce optimism as to the ultimate feasibility of hydrostatic, gas-lubricated piston rings. In addition to test results, the principles of operation, and theoretical developments are presented. Breathable liner concepts are suggested for future consideration. In these configurations, solid hydrostatic pistons are coupled with flexible liners that elastically deform to form a gas-film under hydrostatic pressurization. Breathable liners afford the mechanical simplicity required for mass produced engines, and initial examination indicates satisfactory operation.

Shapiro, W.↗

Static internal performance of a two-dimensional convergent nozzle with thrust-vectoring capability up to 60 deg

An investigation was conducted at wind-off conditions in the static-test facility of the Langley 16-Foot Transonic Tunnel to determine the internal performance characteristics of a two-dimensional convergent nozzle with a thrust-vectoring capability up to 60 deg. Vectoring was accomplished by a downward rotation of a hinged upper convergent flap and a corresponding rotation of a center-pivoted lower convergent flap. The effects of geometric thrust-vector angle and upper-rotating-flap geometry on internal nozzle performance characteristics were investigated. Nozzle pressure ratio was varied from 1.0 (jet off) to approximately 5.0.

Leavitt, L. D.↗

Learjet Model 55 Wing Analysis with Landing Loads

The NASTRAN analysis was used to determine the impact of new landing loads on the Learjet Model 55 wing. These new landing loads were the result of a performance improvement effort to increase the landing weight of the aircraft to 18,000 lbs. from 17,000 lbs. and extend the life of the tires and brakes by incorporating larger tires and heavy duty brakes. Landing loads for the original 17,000 lb. airplane landing configuration were applied to the full airplane NASTRAN model. The analytical results were correlated with the strain gage data from the original landing load static tests. The landing loads for the 18,000 lb. airplane were applied to the full airplane NASTRAN model, and a comparison was made with the original Model 55 data. The results of this comparison enable Learjet to determine the difference in stress distribution in the wing due to these two different sets of landing loads.

Boroughs, R. R.↗

An investigation at static conditions of nonaxisymmetric nozzle thrust reverser port geometry including effects of rounding and rotating the port corner

An investigation has been conducted in the static test facility of the Langley 16-Foot Transonic Tunnel to determine the effects of rounding and rotating the port corner of a nonaxisymmetric thrust reversing port. High pressure air was used to simulate jet exhaust at nozzle pressure ratios up to 6.0. The investigation indicates that using a rounded corner in the reverser port passage increases the discharge coefficient significantly compared to that of a sharp cornered thrust reversing port. Incorporating a rotating cylinder into the rounded corner reverser port passage provides no additional increase at cylinder revolutions per minute up to 10,000. (Revolutions per minute of 390,000 were necessary to achieve a surface velocity equal to the duct velocity.) Highest levels of discharge coefficient are obtained by providing a large, round, cylindrical surface in the port upstream wall. Locating the reverser port in a constant area duct results in higher discharge coefficients than locating the port in a convergent duct.

Arbiter, D. G.↗

Static internal performance of a thrust vectoring and reversing two-dimensional convergent-divergent nozzle with an aft flap

The static internal performance of a multifunction nozzle having some of the geometric characteristics of both two-dimensional convergent-divergent and single expansion ramp nozzles has been investigated in the static-test facility of the Langley 16-Foot Transonic Tunnel. The internal expansion portion of the nozzle consisted of two symmetrical flat surfaces of equal length, and the external expansion portion of the nozzle consisted of a single aft flap. The aft flap could be varied in angle independently of the upper internal expansion surface to which it was attached. The effects of internal expansion ratio, nozzle thrust-vector angle (-30 deg. to 30 deg., aft flap shape, aft flap angle, and sidewall containment were determined for dry and afterburning power settings. In addition, a partial afterburning power setting nozzle, a fully deployed thrust reverser, and four vertical takeoff or landing nozzle, configurations were investigated. Nozzle pressure ratio was varied up to 10 for the dry power nozzles and 7 for the afterburning power nozzles.

Re, R. J.↗

Low-speed performance of an axisymmetric, mixed-compression, supersonic inlet with auxiliary inlets

A test program was conducted to determine the aerodynamic performance and acoustic characteristics associated with the low-speed operation of a supersonic, axisymmetric, mixed-compression inlet with auxiliary inlets. Blow-in-auxiliary doors were installed on the NASA Ames P inlet. One door per quadrant was located on the cowl in the subsonic diffuser selection of the inlet. Auxiliary inlets with areas of 20 and 40 percent of the inlet capture area were tested statically and at free-stream Mach numbers of 0.1 and 0.2. The effects of boundary layer bleed inflow were investigated. A JT8D fan simulator driven by compressed air was used to pump inlet flow and to provide a characteristic noise signature. Baseline data were obtained at static free-stream conditions with the sharp P-inlet cowl lip replaced by a blunt lip. Auxiliary inlets increased overall total pressure recovery of the order of 10 percent.

Trefny, C. J.↗

Solid-propellant rocket motor internal ballistics performance variation analysis, phase 5

The results of research aimed at improving the predictability of internal ballistics performance of solid-propellant rocket motors (SRM's) including thrust imbalance between two SRM's firing in parallel are presented. Static test data from the first six Space Shuttle SRM's is analyzed using a computer program previously developed for this purpose. The program permits intentional minor design biases affecting the imbalance between any two SMR's to be removed. Results for the last four of the six SRM's, with only the propellant bulk temperature as a non-random variable, are generally within limits predicted by theory. Extended studies of internal ballistic performance of single SRM's are presented based on an earlier developed mathematical model which includes an assessment of grain deformation. The erosive burning rate law used in the model is upgraded and made more general. Excellent results are obtained in predictions of the performances of five different SRM's of quite different sizes and configurations. These SRM's all employ PBAN type propellants with ammonium perchlorate oxidizer and 16 to 20% aluminum except one which uses carboxyl terminated butadiene binder. The only non-calculated parameters in the burning rate equations that are changed for the different SRM's are the zero crossflow velocity burning rate coefficients and exponents. The results, in general, confirm the importance of grain deformation. The improved internal ballistic model makes practical development of an effective computer program for application of an optimization technique to SRM design which is also demonstrated. The program uses a pattern search technique to minimize the difference between a desired thrust-time trace and one calculated based on the internal ballistic model.

Sforzini, R. H.↗

Judgments of natural and anomalous trajectories in the presence and absence of motion

Three experiments using McCloskey's curved tube problem, in which people are asked to predict the path that a ball takes when it is shot through a tube curved in a 'C' or spiral, are reported. The first experiment compared the perceptual and representational competencies of observers in recognizing the natural trajectory of the ball, and the second examined the competencies of children on this problem. The third experiment attempted to enhance the representational competence of observers by encouraging them to use a mental imagery approach to the problem. The subjects were presented with both on-going events and with static representations of the event. Men performed better than women under both these conditions, a result not attributable to formal instruction in physics. Children showed no gender effect. The use of mental imagery did not enhance performance on the static test.

Kaiser, M. K.↗

Experimental verification of distributed piezoelectric actuators for use in precision space structures

An analytic model for structures with distributed piezoelectric actuators is experimentally verified for the cases of both surface-bonded and embedded actuators. A technique for the selection of such piezoelectric actuators' location has been developed, and is noted to indicate that segmented actuators are always more effective than continuous ones, since the output of each can be individually controlled. Manufacturing techniques for the bonding or embedding of segmented piezoelectric actuators are also developed which allow independent electrical contact to be made with each actuator. Static tests have been conducted to determine how the elastic properties of the composite are affected by the presence of an embedded actuator, for the case of glass/epoxy laminates.

Crawley, E. F.↗

Thrust imbalance of solid rocket motor pairs on Space Shuttle flights

This analysis extends the investigation presented at the 17th Joint Propulsion Conference in 1981 to include fifteen sets of Space Shuttle flight data. The previous report dealt only with static test data and the first flight pair. The objective is to compare the authors' previous theoretical analysis of thrust imbalance with actual Space Shuttle performance. The theoretical prediction method, which involves a Monte Carlo technique, is reviewed briefly as are salient features of the flight instrumentation system and the statistical analysis. A scheme for smoothing flight data is discussed. The effects of changes in design parameters are discussed with special emphasis on the filament wound motor case being developed to replace the steel case. Good agreement between the predictions and the flight data is demonstrated.

Foster, W. A., Jr.↗

Static internal performance of single-expansion-ramp nozzles with thrust-vectoring capability up to 60 deg

An investigation has been conducted at static conditions (wind off) in the static-test facility of the Langley 16-Foot Transonic Tunnel. The effects of geometric thrust-vector angle, sidewall containment, ramp curvature, lower-flap lip angle, and ramp length on the internal performance of nonaxisymmetric single-expansion-ramp nozzles were investigated. Geometric thrust-vector angle was varied from -20 deg. to 60 deg., and nozzle pressure ratio was varied from 1.0 (jet off) to approximately 10.0.

Berrier, B. L.↗