SEARCH · Search NASA

Results for “storage capability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Metal–Organic Framework-derived Atomic Metal Sites Promoting Sulfur Cathode for All-Solid-State Lithium–Sulfur Batteries

All-solid-state lithium–sulfur batteries (ASSLSBs) offer high energy density and intrinsic safety; however, they still face major challenges, including sluggish redox kinetics and poor sulfur utilization. Incorporating conductive materials into sulfur cathodes is an effective strategy to mitigate these limitations. Here, a highly conductive cobalt–nitrogen–doped carbon (Co–NC) derived from a metal–organic framework (MOF) is introduced to accelerate charge transfer and promote reversible sulfur conversion. Co−NC provides atomically dispersed Co–N sites and conductive carbon pathways that correlate with improved charge transfer, sulfur utilization, and rate capability. Co–NC@S cathode delivers 1499 mAh g–1 at C/20 with a high sulfur loading (5 mg cm–2) and retains 1292 mAh g–1 after five cycles (vs 443 mAh g–1 without Co–NC). Moreover, Co–NC derived ASSLSB achieves 903 mAh g–1 at 5C at 60 °C. This work provides a practical and effective approach to develop high energy, high-rate ASSLSBs.

25 ENERGY STORAGE↗

DOE OSTI2022

Three-dimensional hierarchically porous MoS 2 foam as high-rate and stable lithium-ion battery anode

Architected materials that actively respond to external stimuli hold tantalizing prospects for applications in energy storage, wearable electronics, and bioengineering. Molybdenum disulfide, an excellent two-dimensional building block, is a promising candidate for lithium-ion battery anode. However, the stacked and brittle two-dimensional layered structure limits its rate capability and electrochemical stability. Here we report the dewetting-induced manufacturing of two-dimensional molybdenum disulfide nanosheets into a three-dimensional foam with a structural hierarchy across seven orders of magnitude. Our molybdenum disulfide foam provides an interpenetrating network for efficient charge transport, rapid ion diffusion, and mechanically resilient and chemically stable support for electrochemical reactions. These features induce a pseudocapacitive energy storage mechanism involving molybdenum redox reactions, confirmed by in-situ X-ray absorption near edge structure. The extraordinary electrochemical performance of molybdenum disulfide foam outperforms most reported molybdenum disulfide-based Lithium-ion battery anodes and state-of-the-art materials. This work opens promising inroads for various applications where special properties arise from hierarchical architecture.

25 ENERGY STORAGE↗

DOE OSTI2026

Wyoming Carbon Blueprint A Roadmap for Statewide Carbon Capture and Storage

Wyoming stands at a pivotal point in defining its energy future, and the Wyoming Carbon Blueprint positions the state to lead the nation in carbon management through a coordinated buildout of carbon capture, transportation, utilization, and geologic storage. Building on Wyoming’s long history as a major producer of coal, oil, and natural gas, and supported by favorable policies, skilled labor, and robust subsurface resources, the Blueprint outlines a pathway to develop one of the world’s first open-access carbon hubs capable of capturing between 10 and 25 million tonnes of CO₂ per year within five years, and up to 45 million tonnes within a decade. In doing so, it advances the concept of “No Carbon Left Behind”: a statewide strategy that prevents stranded CO₂ by aligning capture, transport, and storage systems into a single coherent infrastructure network.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2020

Tuning the Kinetics of Zinc-Ion Insertion/Extraction in V 2 O 5 by In Situ Polyaniline Intercalation Enables Improved Aqueous Zinc-Ion Storage Performance

Rechargeable zinc-ion batteries (ZIBs) are emerging as a promising alternative for Li-ion batteries. However, the developed cathodes suffer from sluggish Zn 2+ diffusion kinetics, leading to poor rate capability and inadequate cycle life. Herein, an in situ polyaniline (PANI) intercalation strategy is developed to facilitate the Zn 2+ (de)intercalation kinetics in V 2 O 5 . In this way, a remarkably enlarged interlayer distance (13.90 Å) can be constructed alternatively between the V-O layers, offering expediting channels for facile Zn 2+ diffusion. Importantly, the electrostatic interactions between the Zn 2+ and the host O 2- , which is another key factor in hindering the Zn 2+ diffusion kinetics, can be effectively blocked by the unique π-conjugated structure of PANI. As a result, the PANI-intercalated V 2 O 5 exhibits a stable and highly reversible electrochemical reaction during repetitive Zn 2+ insertion and extraction, as demonstrated by in situ synchrotron X-ray diffraction and Raman studies. Further first-principles calculations clearly reveal a remarkably lowered binding energy between Zn 2+ and host O 2- , which explains the favorable kinetics in PANI-intercalated V 2 O 5 . Benefitting from the above, the overall electrochemical performance of PANI-intercalated V 2 O 5 electrode is remarkable improved, exhibiting excellent high rate capability of 197.1 mAh g -1 at current density of 20 A g -1 with capacity retention of 97.6% over 2000 cycles.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Bipolar Redox‐Active Molecules in Non‐Aqueous Organic Redox Flow Batteries: Status and Challenges

Abstract In this Review, recent advances in the development of organic bipolar redox‐active molecules (BRMs) for redox‐flow batteries (RFBs) are discussed, with special emphasis on their utilization in non‐aqueous systems. BRMs are single molecules that can be used as both anolyte and catholyte. Their unique redox chemistry enables identical components to be present in RFBs, which has distinct advantages in storage, mitigating crossover and compound degradation. Recent scientific innovations have uncovered three main strategies in preparing these bipolar species: developing stable radicals that are capable of both positive and negative redox reactions, covalently bridging electron donor‐acceptor motifs on one single molecule, and forming biredox eutectic mixtures through physically mixing active components. These approaches not only enabled symmetric flow battery design, but also resulted in electroactive materials with improved properties such as solubility, stability, and cell voltage. Nevertheless, much is still to be done. Importantly, developing BRMs that are competitive with vanadium RFBs in all performance indicators (e. g. solubility >1.0 M, voltage output >2.0 V, and cycling longevity >10 000 cycles) remains a challenge. Mechanistic studies including molecular dynamics, plausible degradation processes, and electrode/solution interface are necessary to peer into key parameters that dominate their battery performance. Accordingly, we review the current status and suggest future opportunities in these areas.

Li, Min↗

DOE OSTI2021

Effect of thermal environments on fast charging Li-ion batteries

Battery thermal management systems (BTMSs) are expected to keep the battery temperature at a moderate level (~30 °C) to minimize the thermally exacerbated degradation. However, during fast charging, a strong cooling system is required to restrict the temperature rise of Li-ion batteries (LiBs), which significantly increases the cost and weight of battery packs, and induces a large temperature variation inside the battery. Here, in this work, we find that all these drawbacks could be relieved by allowing LiBs to charge at higher temperatures. Since the fast charging of a LiB only takes a tiny fraction of its lifetime, the aging rate is limited even at a charging temperature of 60 °C. Three types of thermal environments are proposed: kept constant at 30 °C, preheated to 60 °C, and adiabatic fast charging. With an experimentally validated electrochemical-thermal (ECT) coupled model, we explore the interplay between thermal management and the fast-charging performance. It is found that a gradually increasing temperature profile is the best option to balance the lithium plating and thermal management of the battery. Combining adiabatic fast charging with a preheating step, we can achieve minimal cooling need, perfect temperature uniformity within a battery, and fast-charging capability simultaneously.

25 ENERGY STORAGE↗

DOE OSTI2020

A practical phosphorus-based anode material for high-energy lithium-ion batteries

State-of-the-art lithium-ion batteries cannot satisfy the increasing energy demand worldwide because of the low specific capacity of the graphite anode. Silicon and phosphorus both show much higher specific capacity; however, their practical use is significantly hindered by their large volume changes during charge/discharge. Although significant efforts have been made to improve their cycle life, the initial coulombic efficiencies of the reported Si-based and P-based anodes are still unsatisfactory (<90%). In this study, by using a scalable high-energy ball milling approach, we report a practical hierarchical micro/nanostructured P-based anode material for high-energy lithium-ion batteries, which possesses a high initial coulombic efficiency of 91% and high specific capacity of ~2500 mAh g –1 together with long cycle life and fast charging capability. In situ high-energy X-ray diffraction and in situ single-particle charging/discharging were used to understand its superior lithium storage performance. Moreover, proof-of-concept full-cell lithium-ion batteries using such an anode and a LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathode were assembled to show their practical use. The findings presented here can serve as a good guideline for the future design of high-performance anode materials for lithium-ion batteries.

25 ENERGY STORAGE↗

DOE OSTI2024

Optimizing Grid-interactive Efficient Building Designs with Stacked Value Streams

Grid-interactive efficient buildings (GEBs) are those characterized by the combination of energy efficiency and demand flexibility with smart technologies and communications to not only deliver greater affordability and comfort to buildings, but also help utilities manage grid operations and lower system costs. This paper presents an innovative techno-economic assessment framework to effectively examine different GEB design options, explore various use cases, define technically achievable benefits, and thereby assist in informed decision-making. In particular, building load flexibility, thermal storage, and battery energy storage are considered. Advanced optimal dispatch problem is formulated to maximize the stacked value streams from multiple, competing use cases, subject to the physical capabilities and operational flexibility associated with different designs and configurations. Comprehensive case studies were performed for a real-world building to evaluate the cost-effectiveness of different GEB designs and offer in-depth insights. It was found that the proposed assessment method could effectively capture the costs and benefits linked to each GEB design option. Furthermore, the study revealed that outage mitigation and demand response are the two most significant sources of benefits for GEBs.

Ma, Xu↗

DOE OSTI2020

Transfer and Flushing Evaluation for Potential Precipitated Solids in the 241-AP-106 to EMF Transfer Pipeline for DFLAW

Waste transfer pipeline flushing is necessary to maintain pipeline performance, but added flush fluid increases the nuclear waste inventory. During the Direct Feed Low-Activity Waste (DFLAW) mission, waste transfer lines from the Interim Low-Activity Waste Storage Tank (i.e., 241-AP-106) to the Hanford Waste Treatment and Immobilization Plant (WTP) Low-Activity Waste (LAW) Facility must have the capability of being flushed to prevent accumulation of solids and to mitigate corrosion concerns. Operational experience at Hanford has shown that the solids precipitation occurs during processing operations from dilute Hanford liquids. Pacific Northwest National Laboratory was requested to evaluate the potential precipitated solid particle transport and flushing operational capabilities of the AP-106 through the Effluent Management Facility (EMF) low-point drain LAW feed pipeline. The evaluation results do not provide operational requirements, but rather provide a scoping basis for understanding the potential operational significance of solids precipitation in the pipeline. The salt and aluminum phase solids most likely to precipitate from the LAW feeds during cooling, evaporation, or mixing have particle densities that are estimated to range from 1.62 to 2.78 g/mL and a spherical particle size range of 8 to 2100 μm, depending on the solid phase considered. Application of the method to calculate the critical deposition velocity required by TFC-ENG-STD-26 at conservatively bounding estimates for the solids concentrations demonstrates that potentially precipitated solids may deposit on the bottom of the transfer pipe invert at the lower LAW feed pipeline flow rate, but the upper LAW feed pipeline flow rate will likely prevent deposition. The system pressure limit for the AP-106 through the EMF low-point drain LAW feed pipeline likely exceeds any pressure loss at a calculated critical deposition velocity even for the most adverse potential precipitated solid. However, should solids settle as a result of no-flow conditions, the flow capabilities of the AP-106 through the EMF low-point drain LAW feed pipeline are shown, based on the available literature, to be potentially inadequate for effective flushing operations to remove solids, even at solids concentrations below the maximum specified for LAW feed. Thus, stepwise solids accumulations over multiple transfers may be an issue, and eventual line plugging may occur. Further inadequacies may potentially be realized should the cohesive nature of certain precipitates be accounted for.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2021

Component Development for Alkaline URFCs

Performance, cost, and durability of the catalyst materials are the key factors that govern commercialization of H 2 -based energy conversion devices such as unitized regenerative fuel cells (URFCs). Compared to existing battery systems, URFCs offer superior energy density and performance over prolonged operation. In addition, alkaline URFC systems, can utilize low-cost platinum group metal-free (PGM-free) catalysts, resulting in much lower overall system costs. This project seeks to address the major obstacles faced in URFC systems such as cost and efficiency and establish a URFC technical capability through the strategic partnership between UofSC and SRNL. The research focuses on the development of low-PGM and PGM-free based bifunctional oxygen catalysts and electrodes, as well as the development of a URFC testing capability at SRNL.

25 ENERGY STORAGE↗

DOE OSTI2023

Advanced Reactors Integrated Energy System: Thermal Energy Storage Island Design

The main topic of this research is integrated energy systems (IES) designed for pairing industrial thermal energy loads with advanced reactors (ARs). The Idaho National Laboratory (INL) Crosscutting Technology Development IES program and the National Reactor Innovation Center (NRIC) are seeking to develop, design, and construct an AR-IES demonstration platform that couples the thermal output from an AR operating at the INL/NRIC Demonstration of Microreactor Experiments (DOME) test bed in the Experimental Breeder II dome to a variable capacity load emulator (i.e., air-cooled radiator) and sensible thermal energy storage (TES) via a molten salt thermal energy transfer fluid. In the rapidly evolving landscape of energy supply and distribution, flexibility has emerged as a prized attribute, surpassing the traditional notions of stability and baseload generation capability. This shift in priorities is particularly evident in the context of nuclear power plants (NPPs), where adaptability over constant output is becoming more important. As our energy infrastructure and resources embraces the rise of distributed energy generation, the inherent variability in net demand continues to grow. Moreover, the use of nuclear energy as a source of heat for decarbonizing the industrial sector is becoming a very pressing topic. In such environment, advanced NPPs are poised to enter a more competitive energy market, delivering both, flexible electricity and heat. This shift motivates the exploration of TES systems, designed to empower NPPs with nimble responsiveness to market fluctuations, flexible heat delivery capabilities, and redefine their role in the energy field. TES systems offer the unique advantage of storing nuclear energy in its original form as heat, thereby affording unparalleled flexibility in its subsequent utilization.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2025

New helium recapture and reliquefier system for Dynamic Nuclear Polarization at UNH.

A new helium recapture and reliquefaction system, consisting of a gas bag, recapture manifold, cooling chiller, cryogenic purifier and, a gas storage cylinder banks, has been installed in the dynamic nuclear polarized target lab at the University of New Hampshire. This new system has the capability to improve the efficiency of our capacity to do target polarization runs by recycling our cryogenic helium which would otherwise be lost during polarization operations. Our helium liquefier is rated upto 40 L/Day under normal full-capacity operations, and is rated for a capacity of 500 liquid liters of helium. I explain the initial installation process followed by a discussion of the challenges with installation, including issues of impurities which appeared during the initial operation of the system. Then I discuss how we overcame these difficulties. Finally, I discuss the function of the system during normal operation and the present situation of the helium recapture and reliquefaction processing in the UNH Lab.

Lama, Chhetra [Univ. of New Hampshire, Durham, NH ↗

DOE OSTI2024

VPP Participation Models: What is the Objective?

Virtual power plants (VPPs) can provide grid services by aggregating and controlling many distributed energy resources. However, their design, operation, level of participation, and outcomes depend on the regulatory and market environments they operate in, DER owner preferences, grid service value, and technical capabilities (e.g., communications, forecasting, controls, user interfaces). Although VPPs are inherently complex, they could enable high shares of behind-the-meter solar plus storage and reduce the cost of electrifying, e.g., personal vehicles and space heating.

demand response↗

DOE OSTI2022

Development of a MOOSE thermal model of the MPC-32 canister and HI-STORM overpack

Nuclear power is a significant source of electricity in the United States, but the average age of nuclear power plants is around 40 years old. Safe management of spent nuclear fuel (SNF) is a key aspect of the back end of the nuclear fuel cycle, and SNF dry storage systems are becoming a popular, effective solution in this area, given the absence of a final disposal system. The spent fuel cask system (dry cask method) provides a feasible solution for maintaining SNF (~60 years) prior to final disposal. This project aims to develop a thermal model of the MPC-32 canister and HI-STORM overpack, using the Multiphysics Object-Oriented Simulation Environment (MOOSE). MOOSE is an open-source framework developed by Idaho National Laboratory (INL) for multiscale, multiphysics simulations. This study will investigate and demonstrate the thermal-hydraulics capabilities of the MOOSE framework, including natural circulation, heat transfer, porous flows, etc. The ultimate goal of the project is to verify whether MOOSE tools (including Pronghorn) can be used to study the thermal performance of the SNF dry cask storage system. This study provides reliable and inclusive solving strategy for dry cask problems. The detailed information about the solving scheme and the governing equations related to the physics of the system is provided in the report. The results for thermal-hydraulic analysis of the HI-STORM system is produced with using open source modules of the MOOSE framework. This results highlights the flexibility and modularity of the MOOSE which makes it a unique candidate for the frameworks and code packages. Therefore, integration of the MOOSE to UNF ST&DARDS will improve the thermal-hydraulic capability of the system while providing distinctive features to users.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Giant Domain Wall Conductivity in Self‐Assembled BiFeO 3 Nanocrystals

Abstract Ever‐increasing demand on electronic devices with ultrahigh‐density non‐volatile data storage has attracted great interest in novel ferroelectric memories based on conductive ferroelectric domain walls. Embedded in an insulating material, ferroelectric domain walls have the capability of being (re)created, displaced, erased, and altered in their spatial configurations and electronic characteristics. However, the domain wall conductivities are in most cases not yet sufficiently high to ensure the current density required to drive read‐out circuits operating at high speeds. In this work, a giant domain wall current (>10 µA) of a single charged domain wall is obtained through conductive atomic force microscopy with a bias field of 4 V. This is achieved in self‐assembled BiFeO 3 nanocrystals grown by sol‐gel method on Nb‐doped SrTiO 3 substrates. Local configurations of domains and domain wall types are studied using vector piezoresponse force microscopy and high‐resolution transmission electronic microscopy. The enhancement of the wall current is shown to be due to the formation of conducting pathways of charged defects accumulated along domain walls and traversing the nanocrystals. The diverse domain walls can be manipulated by electric field in a perpendicular architecture. The perpendicular array structure of BiFeO 3 nanocrystals should have great potentials for developing perpendicular nanoelectronic prototypes.

Liu, Lisha↗

DOE OSTI2024

Evaluation of hydrogen storage in sandstone reservoirs using 1 H nuclear magnetic resonance spectroscopy

Evaluation of the hydrogen storage capacity of porous rocks is crucial for underground hydrogen storage. Using 1 H nuclear magnetic resonance (NMR) spectroscopy, we successfully characterized the hydrogen responses and identified storage mechanisms in Berea sandstone under varying water saturation. Here, the results indicate that the injected hydrogen behaves as a free gas phase and is capable of occupying the empty pore volume regardless of the saturation state. No hysteresis was observed during injection and production cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Adoption of a token-based authentication model for the CMS Submission Infrastructure

The CMS Submission Infrastructure (SI) is the main computing resource provisioning system for CMS workloads. A number of HTCondor pools are employed to manage this infrastructure, which aggregates geographically distributed resources from the WLCG and other providers. Historically, the model of authentication among the diverse components of this infrastructure has relied on the Grid Security Infrastructure (GSI), based on identities and X509 certificates. In contrast, commonly used modern authentication standards are based on capabilities and tokens. The WLCG has identified this trend and aims at a transparent replacement of GSI for all its workload management, data transfer and storage access operations, to be completed during the current LHC Run 3. As part of this effort, and within the context of CMS computing, the Submission Infrastructure group is in the process of phasing out the GSI part of its authentication layers, in favor of IDTokens and Scitokens. The use of tokens is already well integrated into the HTCondor Software Suite, which has allowed us to fully migrate the authentication between internal components of SI. Additionally, recent versions of the HTCondor-CE support tokens as well, enabling CMS resource requests to Grid sites employing this CE technology to be granted by means of token exchange. After a rollout campaign to sites, successfully completed by the third quarter of 2022, the totality of HTCondor CEs in use by CMS are already receiving Scitoken-based pilot jobs. On the ARC CE side, a parallel campaign was launched to foster the adoption of the REST interface at CMS sites (required to enable token-based job submission via HTCondor-G), which is nearing completion as well. In this contribution, the newly adopted authentication model will be described. We will then report on the migration status and final steps towards complete GSI phase out in the CMS SI.

Pérez-Calero Yzquierdo, Antonio↗

DOE OSTI2023

Phase-based design of CO 2 capture, transport, and storage infrastructure via SimCCS 3.0

The design of optimal infrastructure is essential for the deployment of commercial and large-scale carbon capture and storage (CCS) technology. During the design process, it is important to consider CO 2 capture and storage locations and CO 2 transportation pipelines to minimize the total project cost. SimCCS, first introduced in 2009, is an integrated open-source tool to optimize CCS infrastructure. The core CCS infrastructure design problem in SimCCS is structured as a mixed-integer linear programming problem by selecting the optimal pipeline routes, searching CO 2 source capture and storage locations, and determining the corresponding CO 2 amounts to meet desired capture targets. Multiple important and practical features have been developed to the latest version of SimCCS, SimCCS 3.0 . One of these features is phase-based modeling which enables users to dynamically design the CCS infrastructure. We demonstrate the phased-based modeling capability using two CCS infrastructure optimization case studies. The results from these case studies reveal that the phase-based modeling capability in SimCCS is particularly useful to optimize the dynamic deployment of CCS projects.

54 ENVIRONMENTAL SCIENCES↗