SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Electron microscopy calculations in minimum and maximum capacitance theories for silicon-silicon oxide structures and interfaces
Capacitance sensors for measuring liquid propellant sloshing in space vehicle fuel tanks
Thin film resistance-capacitance lines with resembling open circuit voltage transfer characteristics
Complementary-pair oscillator which generates impulses at very low repetition rate using comparatively low capacitance
We report on the design and development of a heterodyne receiver, designed to cover the frequency range 176-256 GHz. This receiver incorporates a niobium superconductor-insulator-superconductor (SIS) tunnel junction mixer, which, chiefly for reasons of reliability and ease of operation, is a fixed-tuned waveguide design. On-chip tuning is provided to resonate out the junction's geometric capacitance and produce a good match to the waveguide circuit. Laboratory measurements on the first test receiver indicate that the required input bandwidth (about 40%) is achieved with an average receiver noise temperature of below 50 K. Mixer conversion gain is observed at some frequencies, and the lowest measured receiver noise is less than 30 K. Furthermore, the SIS mixer used in this receiver is of simple construction, is easy to assemble and is therefore a good candidate for duplication.
Plants will be an important part of future long-term space missions. Automated plant growth systems require accurate and reliable methods of monitoring soil moisture levels. There are a number of different methods to accomplish this task. This study evaluated sensors using the capacitance method (ECH2O), the heat-pulse method (TMAS), and tensiometers, compared to soil water loss measured gravimetrically in a side-by-side test. The experiment monitored evaporative losses from substrate compartments filled with 1- to 2-mm baked calcinated clay media. The ECH2O data correlated well with the gravimetric measurements, but over a limited range of soil moisture. The averaged TMAS sensor data overstated soil moisture content levels. The tensiometer data appeared to track evaporative losses in the 0.5- to 2.5-kPa range of matric potential that corresponds to the water content needed to grow plants. This small range is characteristic of large particle media, and thus high-resolution tensiometers are required to distinguish changing moisture contents in this range.
Electronic coupling effects such as Inter-Pixel Capacitance (IPC) affect the quantitative interpretation of image data from CMOS, hybrid visible and infrared imagers alike. Existing methods of characterizing IPC do not provide a map of the spatial variation of IPC over all pixels. We demonstrate a deterministic method that provides a direct quantitative map of the crosstalk across an imager. The approach requires only the ability to reset single pixels to an arbitrary voltage, different from the rest of the imager. No illumination source is required. Mapping IPC independently for each pixel is also made practical by the greater S/N ratio achievable for an electrical stimulus than for an optical stimulus, which is subject to both Poisson statistics and diffusion effects of photo-generated charge. The data we present illustrates a more complex picture of IPC in Teledyne HgCdTe and HyViSi focal plane arrays than is presently understood, including the presence of a newly discovered, long range IPC in the HyViSi FPA that extends tens of pixels in distance, likely stemming from extended field effects in the fully depleted substrate. The sensitivity of the measurement approach has been shown to be good enough to distinguish spatial structure in IPC of the order of 0.1%.
NASA interest in ionic silver (Ag+) as a biocide for spacecraft potable water systems motivates the development of Ag+ concentration sensors to ensure nominal dosing. The electrolytic conductivity change of highly-purified potable water is linearly related to the concentration of chemically-dosed Ag+ and could serve as a useful proxy measurement, while the conductivity change during electrolytic dosing may be less so, depending on the influent water chemistry and electrolytic efficiency. Understanding and mitigating the potentially deleterious effects of Ag+ interaction with conductivity measurement systems requires investigation. Issues associated with traditional conductivity cells, which rely on wetted(typically metal or graphite) electrodes, and capacitively-coupled contactless conductivity detection (C4D) for this application are considered. Traditional conductivity cells may potentially be subject to significant excitation-induced or auto-galvanic reduction of Ag+. These may result in Ag+ depletion or electrode fouling and associated measurement error. Proper selection of electrode material, excitation parameters, and cell geometry may limit such effects. C4D uses electrodes placed outside an inert, insulating material, with dielectric polarization enabling the production of an electric field and resultant current across the analyte solution. This approach could potentially mitigate problems with Ag+ depletion and fouling by eliminating the possibility of auto-galvanic deposition and reducing the Faradaic current density. However, it is necessary to confirm C4D performance at very low conductivity levels and to determine if long-term operation produces conductive deposits, which could result in measurement error. A commercial C4D system with 1/16” (1.59 mm)outer diameter flow tubing and claimed performance in the conductivity range appropriate for this application was identified, and its sensitivity in the upper parts of this range was confirmed in a preliminary experiment. A concept for a C4D detector that could allow for full rate flow-through using planar electrodes and thin-film dielectric layers is discussed.
An ultracapacitor made from a polymer loaded with ceramic powder would have several advantages over current ultracapacitors and batteries. First is the possibility of it being printable, which would allow for printing the energy storage device along with the circuit instead of having to find a way to add one later without damaging the rest of the components. When not printed in a specific design for use on a printed wiring board, this type of ultracapacitor could still be cured via a mold to a shape suitable to specific applications. Many polymers maintain some flexibility even after curing, such as the silicone used in this study. The manufacturing process would also be far simpler than that of conventional ultracapacitors.In this work, solid-state ultracapacitors were made by adding the dielectric powder to a two-part polymer (resin and hardener) at the same time. The mixture was then cured in the desired shape at a low temperature until completely set. The addition of the powder to the polymer increased its dielectric properties while leaving most of its physical properties unaltered. At higher powder loading percentages, there were some physical changes as the maximum loading point was approached. To determine the efficiency of these solid-state ultracapacitors, their capacitances were tested, and their dielectric constants (DCs) were measured and compared.
Thermal energy storage (TES) using phase change materials (PCMs) has gained attention as an effective approach to manage energy demand fluctuations and shift peak building loads. PCM embedded heat exchangers (PCM-HXs) offer high energy storage density and low temperature variation during phase change, being suitable for load-shifting applications. However, this component is typically evaluated using computationally expensive methods, which present significant challenges when the ultimate goal is to assess the performance of PCM-HX integrated thermal energy storage systems in the full building context. In this paper, we present a methodology to generate highly accurate and computationally efficient PCM-HX performance maps which can be easily integrated into building energy simulation tools to analyze the feasibility of space conditioning systems with latent heat PCM-based TES. The performance maps are generated using a computationally efficient PCM-HX simulation tool based on a Generalized Resistance-Capacitance Model (GRCM) which can simulate arbitrary PCM-HXs with high accuracy and significantly less computational effort compared to full CFD simulations. The methodology was verified for a case study considering a 5-ton (~17.5 kW) air-to-water heat pump-thermal energy storage system (HP-TES), which was co-simulated in Modelica for a DOE prototype small-office building in Vienna, Austria, using Spawn of EnergyPlus™. The TES performance maps provided accurate predictions of PCM-HX behavior when used as Modelica component, with deviations within 2-4% while also achieving at least 103 computational time reduction. Leveraging this faster prediction capability, four PCMs with different melting temperatures for cooling (12°C, 16°C) and heating (31°C, 36°C) were assessed to investigate their impact on system performance. This work highlights the importance of robust PCM-HX models for efficient and high-fidelity building-level simulations, presenting new opportunities for advanced control strategy development and parametric analysis of TES configurations in a computationally efficient manner
The frequency response of pyroelectric sensors is fundamentally governed by thermal time constant (τth, determined by thermal mass and thermal conductance) and electrical impedance arising from film capacitance and readout circuit. Conventional bulk LiTaO3 detectors are optimized for high responsivity at low modulation frequencies (0.1-10 Hz), possessing a large τth that thermally averages rapid temperature oscillations at elevated modulation frequencies, limiting fidelity in resolving dynamic varying thermal signals. Here, compositional and strain gradients are introduced into 100-nm-thick relaxor-ferroelectric films reducing τth to ≈2 µs and producing built-in potentials (≈1.45 V or 145 kV cm-1) that enhance the pyroelectric coefficient and suppress the dielectric constant. This enables complementary dual-mode operation by enhancing current-mode electrical responsivity and improving the voltage-mode figure of merit - advantageous for superior temperature resolution (ΔTmin ≈ 30 µK). The responsivity peak shifts to near 1 kHz (>2500-times higher than conventional bulk sensors), with measurable responsivity extending to a carrier frequency of 100 kHz and amplitude-resolved detection at modulation frequencies up to 15 kHz. These results establish nanoscale internal-field engineering can reshape electro-thermal trade-off in pyroelectric thin films toward zero-bias, high-thermal-sensitivity, and amplitude-resolved thermal sensing across a wide frequency bandwidth.
Although a few binder-free and self-supported single-atom electrodes have been reported, achieving mechanically robust, defect-engineered, and reproducible films that preserve atomic dispersion under electrochemical operation remains challenging. This work addresses this limitation by presenting a versatile and generalizable strategy to transform powders into standalone, defect-engineered thin films hosting atomically dispersed Ni centers within conductive 2D frameworks. The physicochemical and electronic properties of these materials are thoroughly characterized using a comprehensive set of spectroscopic and microscopic techniques and confirmed the homogeneous dispersion and monoatomic nature of the Ni centers (0.94 wt.%) on the electrode films. Electrochemical testing via cyclic voltammetry and electrochemical impedance spectroscopy under a range of experimental conditions revealed that integration of Ni single atoms markedly enhanced performance and stability compared to carbon nanotube-only electrodes, maintaining integrity after 15 h of continuous operation. This improvement is accompanied by a notable reduction in charge transfer resistance (30.50 Ω) and an increase in double-layer capacitance (295.45 µF). Post-electrochemical analyses corroborated the structural integrity and robustness of the electrodes. Overall, this work bridges atomically precise catalysis and device-level electrochemistry, opening a route toward reproducible and scalable single-atom electrodes for sensing and energy conversion.
Bandgap engineering is a critical tool for tailoring the electronic properties of functional materials, traditionally achieved by modifying the cation sublattice. Here, a generalizable strategy is introduced that leverages facile anion-lattice doping in high entropy materials to modulate the bandgap in high-entropy metal oxides (HEMOs). By incorporating nitrogen into a single-phase high-entropy metal oxide/nitride (HEMO:HEMN) solid solution, a substantial bandgap reduction is achieved from 3.55 eV (HEMO) to ≈2.46 eV (HEMO:HEMN), significantly enhancing electronic conductivity. Unlike conventional bandgap tuning approaches that rely on cation substitution or heterojunction formation, this method exploits anion-mediated entropy stabilization, enabling uniform bandgap narrowing across the entire solid solution. This anion-lattice engineering strategy is broadly applicable to high-entropy systems, providing a new pathway for designing energy materials with tailored electronic properties. The resulting HEMO:HEMN solid solution exhibits a tenfold increase in capacitance and capacity compared to HEMO in supercapacitor and lithium-ion battery tests, demonstrating the transformative potential of anion-driven bandgap modulation for next-generation energy storage and conversion technologies.
Recycling processes for lithium-ion batteries (LIBs) are imperative to support the sustainable growth of global energy storage systems. This study introduces a scalable method for the upcycling of spent graphite anodes from LIBs to produce electronic-grade graphene nanoplatelets. In addition to comprehensive materials characterization, the electronic quality of the upcycled graphene is demonstrated by formulating it into a screen printing ink that achieves high-resolution patterning and thin-film electrical conductivity exceeding 104 S m−1. This screen printing ink is also used to print planar micro-supercapacitors with exceptional areal capacitance (1.78 mF cm−2), areal energy density (0.247 µWh cm−2), and cycling stability (> 10 000 cycles). Life cycle assessment (LCA) and techno-economic analysis (TEA) highlight the environmental benefits and cost reductions attainable through upcycling of graphite from LIBs. By capturing economic value from spent LIBs, this work fosters a sustainable battery supply chain and provides an abundant and geographically distributed raw material for electronic-grade graphene.
Abstract We report on the supercapacitive swing adsorption (SSA) of carbon dioxide at different voltage windows in the presence of oxygen using activated carbon electrodes, and deliquescent, aqueous electrolytes. The presence of O 2 in the CO 2 /N 2 gas mixture results in an up to 11 times higher CO 2 adsorption capacity with 3 M MgBr 2 (at 0.6 V) and up to 4–5 times higher adsorption capacity with 3 M MgCl 2 (at 1 V). A tradeoff between high CO 2 adsorption capacities and lower coulombic efficiencies was observed at voltages above 0.6 V. The energetic and adsorptive performance of the electrodes in the presence of oxygen below 0.5 V was similar to the performance with a CO 2 /N 2 mixture without oxygen at 1 V. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) of the electrodes demonstrate that the specific capacitance increases while the diffusion resistance decreases in the presence of oxygen. Oxygen concentrations ranging between 5–20 % give similar energetic and adsorptive performance. The electrodes exhibit stable performance for up to 100 cycles of operation.
We report on the supercapacitive swing adsorption (SSA) of carbon dioxide at different voltage windows in the presence of oxygen using activated carbon electrodes, and deliquescent, aqueous electrolytes. The presence of O 2 in the CO 2 /N 2 gas mixture results in an up to 11 times higher CO 2 adsorption capacity with 3 M MgBr 2 (at 0.6 V) and up to 4–5 times higher adsorption capacity with 3 M MgCl 2 (at 1 V). A tradeoff between high CO 2 adsorption capacities and lower coulombic efficiencies was observed at voltages above 0.6 V. The energetic and adsorptive performance of the electrodes in the presence of oxygen below 0.5 V was similar to the performance with a CO 2 /N 2 mixture without oxygen at 1 V. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) of the electrodes demonstrate that the specific capacitance increases while the diffusion resistance decreases in the presence of oxygen. Oxygen concentrations ranging between 5–20 % give similar energetic and adsorptive performance. The electrodes exhibit stable performance for up to 100 cycles of operation.
Two-dimensional (2D) metal-organic frameworks (MOFs) integrating redox-active linkers enable dense charge sites and open ion pathways for microscale energy storage. We report a quinoidal dicarboxylate ligand, AQM-H2L, derived from p-azaquinodimethane, forming crystalline frameworks with Cu2+ and Zn2+ nodes. The Cu-based MOF (AQM-AQM-H2L-Cu) exhibits layered sheets (>14 Å spacing) constructed from dinuclear Cu-carboxylate units and conjugated AQM linkers, which narrow the bandgap and introduce Cu2+/Cu+ pseudocapacitance. Exfoliated nanosheets (∼5 nm) retain crystallinity and excellent processability. Integrated into graphene films, they deliver areal and volumetric capacitances of 29.6 mF cm-2 and 18.1 F cm-3, achieving 2.6 mWh cm-3 energy density at 160 mW cm-3. As ionic fillers (1 wt%) in PEO solid polymer electrolytes, the nanosheets markedly enhance LiFePO4 cell performance, affording 169.8 mAh g-1 at 0.2 C and 93% retention after 400 cycles. This work establishes quinoidal linkers as a compact and robust design motif for ionically active 2D frameworks toward high-performance miniature and solid-state energy devices.