Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mechanical Loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Alkaline phosphatase in osteoblasts is down-regulated by pulsatile fluid flow

It is our hypothesis that interstitial fluid flow plays a role in the bone remodeling response to mechanical loading. The fluid flow-induced expression of three proteins (collagen, osteopontin, and alkaline phosphatase) involved in bone remodeling was investigated. Rat calvarial osteoblasts subjected to pulsatile fluid flow at an average shear stress of 5 dyne/cm2 showed decreased alkaline phosphatase (AP) mRNA expression after only 1 hour of flow. After 3 hours of flow, AP mRNA levels had decreased to 30% of stationary control levels and remained at this level for an additional 5 hours of flow. Steady flow (4 dyne/cm2 fluid shear stress), in contrast, resulted in a delayed and less dramatic decrease in AP mRNA expression to 63% of control levels after 8 hours of flow. The reduced AP mRNA expression under pulsatile flow conditions was followed by reduced AP enzyme activity after 24 hours. No changes in collagen or osteopontin mRNA expression were detected over 8 hours of pulsatile flow. This is the first time fluid flow has been shown to affect gene expression in osteoblasts.

Non-NASA Center↗

Fluid flow stimulates rapid and continuous release of nitric oxide in osteoblasts

Interstitial fluid flow may mediate skeletal remodeling in response to mechanical loading. Because nitric oxide (NO) has been shown to be an osteoblast mitogen and inhibitor of osteoclastic resorption, we investigated and characterized the role of fluid shear on the release of NO in osteoblasts. Rat calvarial cells in a stationary culture produced undetectable levels of NO. Fluid shear stress (6 dyn/cm2) rapidly increased NO release rate to 9.8 nmol.h-1.mg protein-1 and sustained this production for 12 h of exposure to flow. Cytokine treatment also induced NO synthesis after a 12-h lag phase of zero production, followed by a production rate of 0.6 nmol.h-1.mg protein-1. Flow-induced NO production was blocked by the NO synthase (NOS) inhibitor NG-amino-L-arginine, but not by dexamethasone, which suggests that the flow stimulated a constitutive NOS isoform. This is the first time that a functional constitutively present NOS isoform has been identified in osteoblasts. Moreover, fluid flow represents the most potent stimulus of NO release in osteoblasts reported to date. Fluid flow-induced NO production may therefore play a primary role in bone maintenance and remodeling.

NASA Discipline Cell Biology↗

Foldable Instrumented Bits for Ultrasonic/Sonic Penetrators

Long tool bits are undergoing development that can be stowed compactly until used as rock- or ground-penetrating probes actuated by ultrasonic/sonic mechanisms. These bits are designed to be folded or rolled into compact form for transport to exploration sites, where they are to be connected to their ultrasonic/ sonic actuation mechanisms and unfolded or unrolled to their full lengths for penetrating ground or rock to relatively large depths. These bits can be designed to acquire rock or soil samples and/or to be equipped with sensors for measuring properties of rock or soil in situ. These bits can also be designed to be withdrawn from the ground, restowed, and transported for reuse at different exploration sites. Apparatuses based on the concept of a probe actuated by an ultrasonic/sonic mechanism have been described in numerous prior NASA Tech Briefs articles, the most recent and relevant being "Ultrasonic/ Sonic Impacting Penetrators" (NPO-41666) NASA Tech Briefs, Vol. 32, No. 4 (April 2008), page 58. All of those apparatuses are variations on the basic theme of the earliest ones, denoted ultrasonic/sonic drill corers (USDCs). To recapitulate: An apparatus of this type includes a lightweight, low-power, piezoelectrically driven actuator in which ultrasonic and sonic vibrations are generated and coupled to a tool bit. The combination of ultrasonic and sonic vibrations gives rise to a hammering action (and a resulting chiseling action at the tip of the tool bit) that is more effective for drilling than is the microhammering action of ultrasonic vibrations alone. The hammering and chiseling actions are so effective that the size of the axial force needed to make the tool bit advance into soil, rock, or another material of interest is much smaller than in ordinary twist drilling, ordinary hammering, or ordinary steady pushing. Examples of properties that could be measured by use of an instrumented tool bit include electrical conductivity, permittivity, magnetic field, magnetic permeability, temperature, and any other properties that can be measured by fiber-optic sensors. The problem of instrumenting a probe of this type is simplified, relative to the problem of attaching electrodes in a rotating drill bit, in two ways: (1) Unlike a rotating drill bit, a bit of this type does not have flutes, which would compound the problem of ensuring contact between sensors and the side wall of a hole; and (2) there is no need for slip rings for electrical contact between sensor electronic circuitry and external circuitry because, unlike a rotating drill, a tool bit of this type is not rotated continuously during operation. One design for a tool bit of the present type is a segmented bit with a segmented, hinged support structure (see figure). The bit and its ultrasonic/sonic actuator are supported by a slider/guiding fixture, and its displacement and preload are controlled by a motor. For deployment from the folded configuration, a spring-loaded mechanism rotates the lower segment about the hinges, causing the lower segment to become axially aligned with the upper segment. A latching mechanism then locks the segments of the bit and the corresponding segments of the slider/guiding fixture. Then the entire resulting assembly is maneuvered into position for drilling into the ground. Another design provides for a bit comprising multiple tubular segments with an inner alignment string, similar to a foldable tent pole comprising multiple tubular segments with an inner elastic cable connecting the two ends. At the beginning of deployment, all segments except the first (lowermost) one remain folded, and the ultrasonic/sonic actuator is clamped to the top of the lowermost segment and used to drive this segment into the ground. When the first segment has penetrated to a specified depth, the second segment is connected to the upper end of the first segment to form a longer rigid tubular bit and the actuator is moved to the upper end of the second segnt. The process as described thus far is repeated, adding segments until the desired depth of penetration has been attained. Yet other designs provide for bits in the form of bistable circular- or rectangular- cross-section tubes that can be stowed compactly like rolls of flat tape and become rigidified upon extension to full length, in a manner partly similar to that of a common steel tape measure. Albeit not marketed for use in tool bits, a bistable reeled composite product that transforms itself from a flat coil to a rigid tube of circular cross section when unrolled, is commercially available under the trade name RolaTube(TradeMark) and serves as a model for the further development of tool bits of this subtype.

Bar-Cohen, Yoseph↗

Improvement of bonding properties of laser transmission welded, dissimilar thermoplastics by plasma surface treatment

Compared to different welding methods such as ultrasonic welding, laser transmission welding is a relatively new technology to join thermoplastic parts. The most significant advantages over other methods are the contactless energy input which can be controlled very precisely and the low mechanical loads on the welded parts. Therefore, laser transmission welding is used in various areas of application, for example in medical technology or for assembling headlights in the automotive sector. However, there are several challenges in welding dissimilar thermoplastics. This may be due to different melting points on the one hand and different polarities on the other hand. So far these problems are faced with the intermediate layer technique. In this process a layer bonding together the two components is placed between the components. This means that an additional step in the production is needed to apply the extra layer. To avoid this additional step, different ways of joining dissimilar thermoplastics are investigated. In this regard, the improvement in the weldability of the dissimilar thermoplastics polyamide 6 (PA 6) and polypropylene (PP) by means of plasma surface modification and contour welding is examined. To evaluate the influence of the plasma surface modification process on the subsequent welding process of the two dissimilar materials, the treatment time as well as the storage time between treatment and welding are varied. The treatment time in pulsed micro wave excited oxygen plasmas with an electron density of about 1x10{sup 17} m{sup −3} is varied from 0.5 s to 120 s and the time between treatment and welding is varied from a few minutes up to a week. As reference, parts being made of the same polymer (PP and PA 6) are welded and tested. For the evaluation of the results of the welding experiments, short-time tensile tests are used to determine the bond strength. Without plasma treatment the described combination of PA 6/PP cannot be welded with sufficient bond strength to withstand handling of the samples. In contrast, the tear-out force of previously plasma treated samples can be determined to up to 1400 N. The achieved bond strengths are higher than of untreated PP/PP welded parts (about 1000 N)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Functional Materials Under Stress: In Situ TEM Observations of Structural Evolution

The operating conditions of functional materials usually involve varying stress fields, resulting in structural changes, whether intentional or undesirable. Complex multiscale microstructures including defects, domains, and new phases, can be induced by mechanical loading in functional materials, providing fundamental insight into the deformation process of the involved materials. On the other hand, these microstructures, if induced in a controllable fashion, can be used to tune the functional properties or to enhance certain performance. In situ nanomechanical tests conducted in scanning/transmission electron microscopes (STEM/TEM) provide a critical tool for understanding the microstructural evolution in functional materials. In our study, select results on a variety of functional material systems in the field are presented, with a brief introduction into some newly developed multichannel experimental capabilities to demonstrate the impact of these techniques.

36 MATERIALS SCIENCE↗

Joining Dissimilar Materials via Rotational Hammer Riveting Technique

A mechanically robust joining method for Mg/Al and Mg/CFRP could enable multi-material assemblies that decrease vehicle weight while offering more flexibility for designers. However, certain challenges exist for joining Mg/Al and Mg/CFRP. Mechanical joining, such as conventional riveting, clinching and bolting do not form a metallurgical bond between the fastener and metal sheet being fastened. Large differences in physical and mechanical properties of metals and polymers make joining Al or Mg to CFRP challenging via various welding techniques. With solid-state and fusion based welding, rapid formation of brittle intermetallic compounds at the Mg/Al interface lead to interfacial fracture under mechanical loading. In this study, a Rotational Hammer Rivet (RHR) technique was developed to fabricate Mg/CFRP and Mg/Al joints. With RHR technique, direct joining between Mg/Al and Mg/CFRP were replaced by joining Mg rivet head and top Mg sheet. Through heat generated by plastic deformation of an Mg rivet, RHR creates a metallurgical bond between rivet head and Mg sheet which seals corrosive electrolyte from penetrating around the rivet head.

riveting, magnesium alloys, CFRP, Dissimilar Joini↗

Multiphysics Modeling of Nuclear Materials

The operating environment of nuclear reactors presents many unique challenges both for the materials comprising fuel elements and other structural components within and surrounding the reactor. These environmental challenges are due to the simultaneous exposure to conditions from multiple physical systems, including high temperatures, high radiation fluxes, aggressive chemical environments, and mechanical loading. Numerical simulation has been used for decades as a tool for understanding the behavior of various components in this environment. As these tools have been developed to increasing levels of sophistication, they have been used increasingly both for engineering analysis of components, as well as for simulating the processes of microstructure evolution, which lead to changes in the engineering properties of interest in the materials used in these components. This document provides an overview of the methods used for multiphysics simulation of nuclear materials, and provides examples of the application of these techniques.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Corrosion Resistance and Mechanical Stability of Nickel Alloys in Molten-Salt Nuclear Reactors

Choosing structural materials for molten-salt nuclear reactors is a high-priority problem. The results making it possible to choose the basic structural material for a molten-salt nuclear reactor are colligated in the present article. Forced and natural circulation setups operating under reactor and laboratory conditions with molten metal-fluoride salts with different compositions have been developed at the National Research Center Kurchatov Institute: LiF–NaF–BeF{sub 2}–PuF{sub 3}, LiF–BeF{sub 2}–UF{sub 4}, and LiF–BeF{sub 2}–ThF{sub 4}–UF{sub 4}. Corrosion tests were conducted with domestically produced corrosion-resistant steel (12Kh18N10T, EP-164) and specially developed nickel-based alloys (KhN80M-VI, KhN80MTYu, KhN80MTV, et al.) as well as the alloy Hastelloy (USA), MONICR (Czechoslovakia) and EM-721 (France) in the working temperature range 600–800°C and mechanical loads up to 80 MPa on the samples.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The Influence of Dispersedly Distributed Cracks on Critical Current of the Nb{sub 3}Sn Strand

The Nb{sub 3}Sn strand is the presently most widely used high field superconductor. However, one important fact is that the transport properties of an Nb{sub 3}Sn strand will degrade obviously when it is subjected to high mechanical loads. Based on the dispersed distribution of cracks in the bronze strand due to a high axial tensile strain, we propose an analytical strand model to describe the influence of cracks on the critical current of the Nb{sub 3}Sn strand. The dependence of the critical current I{sub c} of the strand on crack density is investigated theoretically. It is shown that the calculation results by this model agree with the experimental data. The influence of filament-to-matrix resistance r{sub c} on transport degradation is also discussed since r{sub c} is a key parameter for the total voltage calculation and its realistic value is of great importance for accurate results. We also compared the influence of dispersed and collective cracks on transport properties with specific conditions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A New Residual Strain Mapping Program Using Energy Dispersive X-Ray Diffraction at the Advanced Photon Source

Here, the ability to non-destructively map the residual strain field inside an engineering component is important for predicting its fatigue life or developing processing methods to prevent failure or enhance performance. In this paper, we describe a new residual strain mapping program at the Advanced Photon Source, Argonne National Laboratory. The new program is based on energy dispersive x-ray diffraction (EDXRD). It is capable of non-destructively penetrating a several- cm thick polycrystalline sample fabricated from engineering alloys using high-energy x-rays and measuring the residual strain field with mm or better spatial resolution and approximately ±1 x 10 -4 strain resolution. A multi-element detector array is employed to measure multiple strain components simultaneously. The residual strain mapping setup is augmented with a high-energy tomography capability, allowing precise alignment of the material volume of interest for residual strain mapping and providing a complementary view of the structure to understand the measured strain field. These measurement capabilities are demonstrated using several strain mapping examples ranging from polycrystalline structural alloys to biological materials. We also provide some guidance for the future users of the program for a successful residual strain mapping experiment. We are expanding the capabilities of the new setup with various in situ capabilities including thermo-mechanical loading.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

An EBSD Evaluation of the Microstructure of Crept Nimonic 101 for the Validation of a Polycrystal–Plasticity Model

Nimonic 101 is one of the early nickel-based superalloys developed for the use in gas turbines. In such environments, the material is exposed to a combination of both high temperatures and mechanical loads for a long duration. Hence, thermal creep is of the utmost concern as it often limits service life. This study focuses on creep tests, carried out on Nimonic 101 at different temperatures under a constant tensile load of 735 MPa. To characterize the microstructural evolution, electron backscatter diffraction (EBSD) measurements were employed before and after loading. At higher temperatures, a significant change of the microstructure was observed. The grains elongated and aligned their orientation along the load axis. In parallel, a crystal plasticity material model has been set up in the classical large deformation framework. Modeling results are compared to the acquired EBSD data.

36 MATERIALS SCIENCE↗

Dynamic Tensile Response of a Fe–49Co–2V Alloy at Various Strain Rates and Temperatures

Soft ferromagnetic alloys are often utilized in electromagnetic applications due to their desirable magnetic properties. In support of these applications, the ferromagnetic alloys are also required to bear mechanical load under various loading and environmental conditions. In this study, a Fe–49Co–2V alloy was dynamically characterized in tension with a Kolsky tension bar and a Drop–Hopkinson bar at various strain rates and temperatures. Dynamic tensile stress–strain curves of the Fe–49Co–2V alloy were obtained at strain rates ranging from 40 to 230 s -1 and temperatures from - 100 to 100 °C. All dynamic tensile stress–strain curves exhibited an initial linear elastic response to an upper yield followed by Lüders band response and then a nearly linear work-hardening behavior. The yield strength of this material was found to be sensitive to both strain rate and temperature, whereas the hardening rate was independent of strain rate or temperature. The Fe–49Co–2V alloy exhibited a feature of brittle fracture in tension under dynamic loading with no necking being observed.

36 MATERIALS SCIENCE↗

Computational Homogenization of Polycrystals

This paper reviews the current state of the art in the simulation of the mechanical behavior of polycrystalline materials by means of computational homogenization. The key ingredients of this modeling strategy are presented in detail starting with the parameters needed to describe polycrystalline microstructures and the digital representation of such microstructures in a suitable format to perform computational homogenization. The different crystal plasticity frameworks that can describe the physical mechanisms of deformation in single crystals (dislocation slip and twinning) at the microscopic level are presented next. This is followed by the description of computational homogenization methods based on mean-field approximations by means of the viscoplastic self-consistent approach, or on the full-field simulation of the mechanical response of a representative polycrystalline volume element by means of the finite element method or the fast Fourier transform-based method. Multiscale frameworks based on the combination of mean-field homogenization and the finite element method are presented next to model the plastic deformation of polycrystalline specimens of arbitrary geometry under complex mechanical loading. Examples of application to predict the strength, fatigue life, damage, and texture evolution under different conditions are presented to illustrate the capabilities of the different models. Lastly, current challenges and future research directions in this field are summarized.

36 MATERIALS SCIENCE↗

Two modes of screw dislocation glide in fcc single-phase concentrated alloys

Concentrated solid solution alloys (CSSAs), including medium- and high-entropy alloys, are currently being considered as prospective materials in many applications. The behavior of CSSAs under different conditions, including mechanical loading, differs from that of conventional alloys and has been the subject of intensive study by different techniques. In many cases, their behavior is treated by modifying solid solution hardening models, which, in principle, does not reflect many important features of CSSAs where the distinction between solute and solvent atoms is not clear. In this work, we report the results of an atomic-scale study of ½<110>{111} screw dislocation motion in an fcc equiatomic Ni-Fe alloy. Molecular dynamics simulations demonstrate that the dislocation has two distinctive modes for glide. At lower stress, dislocations move in a very rough manner that cannot be described as continuous glide but rather as jerky motion through a set of obstacles. At high stress, they glide in a manner similar to lattice friction-controlled conditions in single component systems. The stress for the transition between modes depends on the dislocation segment length and temperature. As a result, at 300 K, the flow stress saturates at ~130 MPa for lengths above ~140 |b| (b is the Burgers vector).

36 MATERIALS SCIENCE↗

On the origin of internal obstacles to dislocation glide in single-phase NiFe random alloys

Over the past decade, a new class of unconventional alloys, where several constitutive elements are presented in close to equal concentrations, is considered as promising structural materials in many applications. Properties and behavior of many concentrated solid solution alloys (CSSAs) under different conditions, including mechanical loading, differs from that of conventional alloys and has been the subject of intensive studies by different techniques. A key feature of these materials is that there is no clear distinction between solute and solvent species of atoms, which is the conventional approach to considering dislocation motion in alloys. To understand this regime, we have recently reported on the glide of a screw dislocation glide in a simple equiatomic NiFe alloy and reported the two-mode character. At low applied stress, the dislocation motion is similar to a glide through a field of obstacles. In this work, we report the results of a detailed study on the nature of these internal obstacles. We demonstrate that these are not conventional localized “obstacles” but is the result of significantly different energies of instantaneous dislocation configurations over the alloy bulk. The strong pinning positions are associated with composition changes in the partial dislocation cores, while observing no significant composition changes along the stacking faults. Local energies can vary significantly, as demonstrated using simulations of short-periodicity dislocation lines. Therefore, the critical stress to move a dislocation under such conditions is not a constant Peierls stress but represents a wide spectrum of barriers between different non-straight valleys that the dislocation line accommodates in the bulk at particular stress/strain conditions.

36 MATERIALS SCIENCE↗

Atomistic modeling of interface strengthening in Al-Si eutectic alloys

Al-Si cast alloys are usually composed of α-Al and Al-Si eutectic. Si flakes and Al matrix generally hold cube-on-cube orientation relationship with the primary interface (111) Al ∥(111) Si . Extensive experimental studies demonstrated that Si flakes cannot significantly improve mechanical properties of Al-Si cast alloys. We hypothesize that the weak strengthening effect associated with Si flakes might be attributed to thermomechanical properties of Al-Si interfaces besides their morphologies. To characterize Al-Si interfaces with a large lattice mismatch (> 30%), we proposed the quasi-coincident site lattice (Q-CSL) as reference lattice, and demonstrated that the Q-CSL Al-Si coherent interface has three characteristic coherent structures, one stable and low energy structure and two metastable and high energy structures. The translation vectors for the same type of coherent Q-CSL structures are consistent with three displacement shift complete (DSC) vectors. The two metastable structures can be obtained by shifting the low energy structure with three partial DSC vectors. Semi-coherent interface is composed of the low energy Q-CSL patches and three sets of interface misfit dislocations with Burgers vectors same as the DSC vectors. Atomistic simulations revealed that Al-Si interface exhibits low shear resistance. Ideal shear strength of the Q-CSL coherent interface is 110 MPa and semi-coherent interface is 20 MPa. The low shear resistance is attributed to the glide of interface misfit dislocations. Al-Si interface also exhibits low formation and migration energies of point defects. Owing to low shear strength and low formation and migration energies of point defects, interface sliding or shear readily happen under mechanical loading or during dislocation-interface interactions. Lattice dislocations can cross slip onto or climb along Al-Si interfaces. These reactions decrease the number of accumulated dislocation loops around Si flakes and promote nucleation and emission of lattice dislocations from Al-Si interfaces to matrix, consequently reduce the repulsive force on approaching dislocations and weaken Si flakes strengthening effect. In situ tension and compression tests in a scanning electron microscope reveal relatively weak strengthening effect due to Si flakes, consistent with the computed dislocation interaction with interfaces and shear behavior of interfaces.

36 MATERIALS SCIENCE↗

Multifunctional approaches for safe structural batteries

Recent advancements in Li and Li-ion based energy storage resulted in development of novel electrode materials for higher energy density which are finding their applications in transportation. There appears to be a limitation in improvement of specific energy of the system based solely on design of material compositions for multivalent intercalation compounds. In addition, higher energy stored by the system implies need for addressing safety concerns especially when it comes to large automotive battery packs. New approaches for improvement of both energy density and safety of batteries are emerging, where multifunctionality of the materials and/or architectures is utilized. Here, we present a review for such approaches from multifunctional current collectors to design of batteries capable of supporting mechanical loads and thus possessing ability to be used as a structural component.

25 ENERGY STORAGE↗