Search NASA⌕ Search

SEARCH · Search NASA

Results for “Directional Solidification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Layer-by-Layer Freezing of Nanoconfined Water

Abstract Nanoconfined water plays a pivotal role in a vast number of fields ranging from biological and materials sciences to catalysis, nanofluidics and geochemistry. Here, we report the freezing and melting behavior of water (D 2 O) nanoconfined in architected silica-based matrices including Vycor glass and mesoporous silica SBA-15 and SBA-16 with pore diameters ranging between 4–15 nm, which are investigated using differential scanning calorimetry and 2 H nuclear magnetic resonance spectroscopy. The results provide compelling evidence that the extreme dynamical heterogeneity of water molecules is preserved over distances as small as a few angstroms. Solidification progresses in a layer-by-layer fashion with a coexistence of liquid-like and solid-like dynamical fraction at all temperatures during the transition process. The previously reported fragile-to-strong dynamic transition in nanoconfined water is argued to be a direct consequence of the layer-by-layer solidification.

42 ENGINEERING↗
DOE OSTI2023

Assessment of Directionally Solidified Eutectic Sm–Fe(Co)–Ti Alloys as Permanent Magnet Materials

Sm–Fe–Ti and Sm–Fe0.8Co0.2–Ti alloys were prepared via arc-melting and directionally solidified on a water-cooled copper hearth. The as-solidified alloys featured cells of the Sm(Fe,Co,Ti)12–Ti(Fe,Co) 2+δ –(α-Fe) lamellar eutectic. The lamellae of Sm(Fe,Co,Ti)12 phase with a crystal structure of the ThMn12 type were less than 0.2 μm thick, and had their [001] easy-magnetization directions oriented along the temperature gradient of the solidification. The eutectic microstructure led to an increased coercivity, especially in the Co-added alloys. Below 250 °C, this coercivity was found not to vary much with temperature with a temperature coefficient of -0.18 %/°C. However, the modest absolute values, reaching only 0.7 kOe, are insufficient for utilization of the directionally solidified alloys as anisotropic permanent magnets.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Thermal fatigue and oxidation data on TAZ-8A, MAR-M 200, and Udimet 700 superalloys

The fluidized bed technique was used to determine the relative thermal fatigue and oxidation resistance of three superalloys: TAZ-8A, Mar-M 200, and Udimet 700. The alloys TAZ-8A and MAR-M 200 were also tested in the directionally-solidified form. For the 13 combinations of composition, solidification method, surface protection, and specimen geometry, the cycles to cracking varied from 1250 to 15,000. The alloy/coating having the best resistance to thermal fatigue cracking was coated directionally-solidified NASA TAZ-8A. This combination also had excellent oxidation resistance.

Howes, M. A. H.↗
DOE OSTI2025

Isothermal solidification for high-entropy alloy synthesis

Kinetically trapping the high-temperature states through rapid cooling solidification is widely used for the synthesis of high-entropy alloys (HEAs), especially those with intrinsically immiscible elemental combinations. However, strategies need to be developed to overcome the fundamental limitations of rapid cooling solidification in controlling the crystallinity, structure and morphology of HEAs. Here, in this study, we introduce an isothermal solidification strategy for the synthesis of HEAs by rapidly altering the metal alloy composition through liquid–liquid interface reactions at low temperatures, for example, from 25 °C to 80 °C. We use gallium (Ga)-based metal as the sacrificial reagent and mixing medium. By directing the reactions to the interfaces between the Ga-based liquid metal and an aqueous metal ion solution, the foreign metal ions can be reduced at the interfaces and incorporated into the liquid metal quickly. HEAs with various crystallinity (single crystal, mesocrystal, polycrystal and amorphous), morphology (zero, two and three dimensions) and compositions can be achieved through the isothermal solidification. Ga can be completely consumed, resulting in Ga-free HEAs. If desired, Ga can be one of the metal elements in the final products. In situ liquid phase transmission electron microscopy (TEM) studies and theoretical analysis show the isothermal solidification mechanisms. Our direct observations show the enhanced mixing of liquid metal elements and the solidification process with fluctuating nucleation dynamics. The isothermal solidification marks a powerful strategy for HEA synthesis through an unexplored pathway of kinetically trapping the high-entropy states.

Zhang, Qiubo [Lawrence Berkeley National Laborator↗
NASA NTRS1983

Effect of variable thermal conductivity on isotherms in Bridgman growth

A change in thermal conductivity associated with melting or solidification can have a profound influence on the isotherms near the solidification interface if the material is being directionally solidified in an ampoule whose walls carry a substantial portion of the heat. This analysis was prompted by a recent discovery that the thermal conductivity of Hg(1-x)CD(x)Te increased dramatically as the material is heated above the solidus curve. An illustrative example is shown in which the sample is approximated as an infinite cylinder with constant but diffferent thermal properties in the solid and melt. The boundary conditions are fixed on the surface by a conductive ampoule in a two-zone Bridgman furnace with an adiabatic region separating the two zones. The effect of the adiabatic zone in this case is to intensify the curvature of the interface rather than to lessen it.

Naumann, R. J.↗
NASA NTRS1996

Producing Foils From Direct Cast Titanium Alloy Strip

This research was undertaken to demonstrate the feasibility of producing high-quality, thin-gage, titanium foil from direct cast titanium strip. Melt Overflow Rapid Solidification Technology (MORST) was used to cast several different titanium alloys into 500 microns thick strip, 10 cm wide and up to 3 m long. The strip was then either ground, hot pack rolled or cold rolled, as appropriate, into foil. Gamma titanium aluminide (TiAl) was cast and ground to approximately 100 microns thick foil and alpha-2 titanium aluminide (Ti3AI) was cast and hot pack rolled to approximately 70 microns thick foil. CP Ti, Ti6Al2Sn4Zr2Mo, and Ti22AI23Nb (Orthorhombic), were successfully cast and cold-rolled into good quality foil (less than 125 microns thick). The foils were generally fully dense with smooth surfaces, had fine, uniform microstructures, and demonstrated mechanical properties equivalent to conventionally produced titanium. By eliminating many manufacturing steps, this technology has the potential to produce thin gage, titanium foil with good engineering properties at significantly reduced cost relative to conventional ingot metallurgy processing.

Stuart, T. A.↗
NASA NTRS2004

Materials Processing in Space: Model Experiments aboard the International Space Station

Direct observation of fluid flow, bubble movement and solidification during controlled melting and solidification of succinonitrile were conducted in the glovebox facility of the International Space Station (ISS). The samples were processed in the Pore Formation and Mobility Investigation (PFMI) apparatus in the glovebox facility (GBX) on board the ISS. Experimental processing parameters of temperature gradient and translation speed, as well as camera settings, were remotely monitored and manipulated from the ground Telescience Center (TSC) at the Marshall Space Flight Center. Real time visualization of the controlled directional melt back and resolidification reveals a number of microgravity dependent phenomena otherwise masked by Earth s gravity. These and some initial analysis of the observed events is presented.

Grugel, Richard↗
NASA NTRS1984

NBS (National Bureau of Standards): Materials measurements

Work in support of NASA's Microgravity Science and Applications Program is described. The results of the following three tasks are given in detail: (1) surface tensions and their variations with temperature and impurities; (2) convection during unidirectional solidification; and (3) measurement of high temperature thermophysical properties. Tasks 1 and 2 were directed toward determining how the reduced gravity obtained in space flight can affect convection and solidification processes. Emphasis in task 3 was on development of levitation and containerless processing techniques which can be applied in space flight to provide thermodynamic measurements of reactive materials.

Manning, J. R.↗
NASA NTRS1994

Reply

Treiman (this issue) argues that the melting temperature of carbonatite used by Gregg and Greeley (1993) is too low, and that values presented for other thermophysical properties for carbonatite lava are more appropriate for carbonatite rock. With the exception of the mechanical solidification temperature, values presented by Gregg and Greeley (1993) were taken directly, or calculated, from values presented within the works by Dawson et al. (1990) and Keller and Krafft (1990). Because a mechanical solidification temperature for carbonatite lavas was not presented in those works, we estimated one based on extrusion temperature, Venusian surface pressure, and the temperatures measured in cooling carbonatite lava lakes. We have reexamined values shown for properties of carbonatite lavas used by Gregg and Greeley (1993), and concur that Treiman's arguments (Treiman, this issue) are valid. Here, we present results of analyses described in Gregg and Greeley 1993, using values for the properties of carbonatite lavas obtained from Treiman and Schedl (1983) and Norton and Pinkerton (1990).

Gregg, Tracy K. P.↗
DOE OSTI2022

Mechanical Behavior of Additively Manufactured Molybdenum and Fabrication of Microtextured Composites

Refractory metals are a class of high-melting-temperature materials suitable for use in extreme environment applications. Interestingly, during additive manufacturing many pure refractory metals exhibit a switch from (001) to (111) build direction fiber preference with increasing surface energy density. Here we exploit this solidification physics to fabricate material with “mesoscale composite” engineered structures consisting of features with contrasting (001) and (111) build direction microtextures. Separately, elevated temperature tensile testing of EBM fabricated material with a randomized distribution of mixed (001)/(111)-fiber grains is shown to exhibit excellent properties. These results are utilized to build a crystal plasticity model for evaluating the local inelastic response of the composite mesoscale structures. Analysis of printed microstructures and microstructure-scale simulations indicate that both macro-scale and localized material behavior may be tailored. This strategy can be potentially used to synthesize materials with optimized performance for high-temperature applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Localized Strain Analysis of Ce- and Mg-Treated Cast Iron under Uniaxial Compression

Cast iron exhibits a wide range of mechanical properties, depending on its microstructural features. The microstructure of cast iron consists of several microconstituents with different elastic-plastic behavior, making the strain non-uniform across the bulk material. To understand the individual effects of these microconstituents on the overall mechanical behavior, local strain analysis using digital image correlation analysis was carried out. Samples with two different compositions (varying cerium, magnesium and silicon) were processed at different solidification velocities in a Bridgman furnace. Sections of the directionally solidified samples were loaded under uniaxial compression to measure global and local strain behavior. Despite the variability of the microstructure, the stress–strain curves obtained by digital image correlation (DIC) were found to react in a well-controlled way to changes in solidification velocity. It was observed that high-strain failure (greater than 15%) was accompanied by local straining of the softer ferritic phase, but during low-strain failure, local straining was not prominent. Higher nodularities, due to higher solidification velocities, raised the compressive strength without affecting the toughness significantly. Higher percentages of carbides led to higher compressive strengths with corresponding losses in ductility. The continuity of the matrix was also found to play an important role in the behavior during compression.

ductile failure↗
NASA NTRS1984

The solidification of monotectic alloys - Microstructures and phase spacings

The microstructures of directionally grown monotectic alloys in metallic and organic systems fall into two categories those which can form aligned fibrous composite structures with even phase spacings and fiber sections, and those in which the phase distribution is coarser and less regular. This division appears to relate to the form of the phase diagram and has been rationalized by Cahn (1977, 1979) in terms of the relative surface energies between solid and two liquids to give steady state or nonsteady state profiles. The transition in growth behavior occurs when the ratio of the monotectic temperature to that of the upper consolute temperature is approximately 0.9. Differences in phase spacings between a range of monotectic and eutectic systems are discussed in terms of the expected growth interface shapes and the factors which will influence them.

Grugel, R. N.↗
NASA NTRS2001

Shuttle Flight Experiment on USMP-4: In Situ Monitoring of Crystal Growth Using MEPHISTO

This reports on the MEPHISTO-4 experiment on the Space Shuttle Columbia, STS-87, November 19-December 5, 1997. Involved were NASA; the University of Florida at Gainesville; groups from France that developed and built the furnace; the National Institute of Standards and Technology; The University of New South Wales, Australia; and Purdue University. This was a solidification study in which three long rods of Bismuth- 1 at.% Tin were directionally solidified. The goals were to solidify in an environment free of natural convection; to determine the relationship among solidification growth velocity, growth mode, and temperature; and determine the diffusivity of Sn in Bi. The flight samples grew with a planar solid/liquid interface at velocities less than 3.4 gm/s, and cellular growth was present at velocities greater than 6.7 um/s; grain orientation influenced the planar to cellular transition. The temperature gradient in the liquid was 204 K/cm. The s/l interface was flat with slight concavity. Diffusion-dominated conditions were present during MEPHISTO-4. The Seebeck technique was used to determine the s/I interface temperature during growth, however, to date, analysis of the Seebeck results has not yielded a reliable measurement of the interface temperature. The partition coefficient for Bi alloyed with Sn was measured, k = 0.029.

Abbaschian, Reza↗
DOE OSTI2018

Interaction between laser radiation and metallic powder of 316L austenitic steel during selective laser melting

Highlights: • Single and multiple tracks on a loose bulk powder substrate were generated. • Understanding of the microstructure development during SLM was achieved. • Single tracks reveal a nearly symmetrical crystallography with elongated grains. • Multiple tracks show elongated grains perpendicular to the build direction. - Abstract: During selective laser melting (SLM), a complex heat state develops that leads to a characteristic crystallography and microstructure of the processed materials. Depending on the geometry of the processed part, most scan tracks of a new layer, so-called hatches, are located above a dense substrate or already solidified structures whereas others are located above loose powder. This is, inter alia, the case for overhanging structures. Attributable to the lower thermal conductivity of loose powder, temperature gradients and cooling rates of the melt pool differentiate in these areas, resulting in a different microstructural build-up. In this work, the microstructure and the crystallographic orientation of grade 316L austenitic stainless steel processed by SLM was investigated to understand the interaction between the laser radiation and the metallic powder during SLM-processing and to investigate the remelting of a track on a previous SLM-densified track. Single and multiple tracks on a loose bulk powder substrate, as well as single tracks on a dense substrate plate, were generated. A parameter study revealed that high energy densities are necessary to build continuous tracks on a loose bulk powder substrate. In addition, the amount of adhered particles, which are sintered on the fully melted and solidified tracks, is determined in comparison to the melted powder because the sintered particles strongly influence the surface roughness. To understand the microstructure development and, particularly, the influence of adjacent hatches during SLM-processing, investigations on the resulting microstructure and crystallographic orientation of a single track and two connected multiple tracks were carried out. During SLM processing of the tracks, the substrate plate and the solidified structures influence the temperature gradient and cooling rate of the melt pool, thus directionally solidified and elongated grains occur. Furthermore, the solidification is characterized by an epitaxial growth due to a distinct thermal gradient between the melt pool and the surrounding elements.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Enabling 6.5% Silicon Electric Steel for Motor Application

Compared to the most widely used 3.2% Si steel, 6.5% Si steel exhibits superior magnetic and electric properties and promises an improvement to the efficiency and power density of electrical machines and transformers. However, due to the heterogeneous formation of B2 and D03 ordered phases, 6.5% Si steel is too brittle to be produced using the traditional cold roll process. And the thin sheet obtained via Si vapor deposition followed by diffusion process is difficult to stamp and assemble. At Iowa State University and Ames Laboratory, a novel process was developed to enable the cost-effective deployment of this brittle materials. The process is developed based on the observation that the deleterious ordered phases can be fully or partially suppressed by rapid cooling. The innovation lies in the production of small ductile flakes using rapid solidification and the consolidation of the obtained flakes directly into a fully dense part with near-net-shape.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Solidification processing superalloys in an electric field

The phase morphology of a given superalloy's microstructure is established during solidification. Solidification-processing in an applied electric field is a technique currently undergoing experimental characterization at NASA-Marshall. The method is predicated on the simplest model of a metallic solid, in which ions are arranged in basic space lattices that are permeated by an 'electron gas' whose valence electrons are free to move in the solid. When in a superheated liquid state, the metal is seen as a dense 'cold plasma' of electrons and ions. The application of an electric field during solidification establishes a steady, continuous current flow; the direction of propagation of the plasma waves coincides with the direction of the electric field. Such an alignment introduces an ordered arrangement of the electric vectors and introduces an additional degree of order in an already highly ordered alloy.

Ahmed, Shaffiq↗
NASA NTRS2000

Onset of Convection Due to Surface Tension Variations in Multicomponent and Binary Fluid Layers

Under certain conditions, such as in thin liquid films or microgravity, surface tension variations along a free surface can induce convection. Convection onset due to surface tension variation is important to many terrestrial technological processes in addition to microgravity materials processing applications. Examples include coating, drying crystallization, solidification, liquid surface contamination, and containerless processing. In double-diffusive and multicomponent systems, the spatial variations of surface tension are associated with two or more stratifying agencies, respectively. For example, both temperature and species (concentration) gradients are associated with convection in the solidification of binary alloys or salt ponds. The direction of the two (or more) gradients has a profound effect on the nature of the flow at or slightly beyond the onset of convection. Our recent work at the NASA Lewis Research Center focused on characterizing surface-tension-induced onset of convection, often referred to as Marangoni-Benard convection. Exact solutions for the stationary neutral stability of multicomponent fluid layers with interfacial deformation were derived. These solutions also permit the computation of a boundary curve that separates the long and finite wavelength instabilities. Computing points along this boundary using the exact solution (when possible) is more efficient than the typical numerical approaches, such as finite difference or spectral methods. Above the curve, a long wavelength instability was predicted, suggesting that convection would occur principally through one large flow cell in the layer, whereas below the curve, finite wavelength instabilities occur which suggest multiple finite-sized circulation cells. For many common liquids with layer depths greater than 100 mm, finite wave instability is predicted under terrestrial conditions; however, with little exception, long wavelength instability is predicted in microgravity for the identical fluid systems.

Skarda, J. Raymond Lee↗
DOE OSTI2019

Interaction of Strain Refined Precipitates and Recrystallized Grains in Nb-Ti Microalloyed Steel during Continuous Casting, Hot-Core Heavy Reduction Rolling, and Reheating Process

Hot-core heavy reduction rolling (HHR{sup 2}) is an energy-saving process that directly rolls continuously cast slabs at the end of solidification that have a large temperature gradient. Here, we elucidated the interaction of strain refined precipitates and recrystallized grains in Nb-Ti microalloyed steel during continuous casting, hot-core heavy reduction rolling, and reheating process. Furthermore, theoretical models were established to calculate recrystallization driving force and pinning force at temperatures in the range of 850-1300 °C by a two-stage interrupted compression test using a Gleeble-3800 thermomechanical simulator. The study indicated that a random dispersion of strain refined precipitates with a size range of ~ 6-10 nm was obtained in the hot-core heavy reduction rolled slab, which was different from the coarse and uneven distribution of precipitates in a conventional slab. Upon reheating, the austenite grains in the hot-core heavy reduction rolled slab were significantly refined and evenly distributed along the thickness direction. This is attributed to the random dispersion of strain refined precipitates formed in the HHR{sup 2} process.

36 MATERIALS SCIENCE↗