Search NASA⌕ Search

SEARCH · Search NASA

Results for “atomically thin”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Measurement of transient atomic displacements in thin films with picosecond and femtometer resolution

We report measurements of the transient structural response of weakly photo-excited thin films of BiFeO 3 , Pb(Zr,Ti)O 3 , and Bi and time-scales for interfacial thermal transport. Utilizing picosecond x-ray diffraction at a 1.28 MHz repetition rate with time resolution extending down to 15 ps, transient changes in the diffraction angle are recorded. These changes are associated with photo-induced lattice strains within nanolayer thin films, resolved at the part-per-million level, corresponding to a shift in the scattering angle three orders of magnitude smaller than the rocking curve width and changes in the interlayer lattice spacing of fractions of a femtometer. The combination of high brightness, repetition rate, and stability of the synchrotron, in conjunction with high time resolution, represents a novel means to probe atomic-scale, near-equilibrium dynamics.

36 MATERIALS SCIENCE↗

Cation stoichiometry optimization of SrTiO{sub 3} (110) thin films with atomic precision in homogeneous molecular beam epitaxy

We study the evolution of surface reconstructions on SrTiO{sub 3} (110) determined by cation concentration ratio and find it detectable by high energy electron diffraction (RHEED) even at high temperature up to 800 deg. C. The evaporation rate of Sr and Ti sources can be calibrated precisely by monitoring RHEED patterns in situ and in real time during the extended homogeneous oxide molecule beam epitaxy growth of SrTiO{sub 3} (110) film. High quality film is obtained with deviation of cation stoichiometry less than 0.5%.

36 MATERIALS SCIENCE↗

Fabrication of ion conductive tin oxide-phosphate amorphous thin films by atomic layer deposition

This work reports the atomic layer deposition (ALD) of tin oxide-phosphate films using tetrakis(dimethylamino)tin and trimethyl phosphate as precursors. The growth rates were 1.23–1.84 Å/cycle depending upon the deposition temperature and precursor combination. The ionic conductivity of the ALD tin oxide-phosphate films was evaluated by cross-plane impedance measurements in the temperature range of 50–300 °C under atmospheric air, with the highest conductivity measured as 1.92 × 10{sup −5} S cm{sup −1} at 300 °C. Furthermore, high-resolution x-ray photoelectron spectroscopy exhibited two O1s peaks that were classified as two subpeaks of hydroxyl ions and oxygen ions, revealing that the quantity of hydroxyl ions in the ALD tin oxide-phosphate films influences their ionic conductivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Interaction of atomic oxygen with thin film and bulk copper: An XPS, AES, XRD, and profilometer study

The University of Alabama in Huntsville (UAH) experiment A-0114 was designed primarily to study degradation of material surfaces due to low earth orbital (LEO) atmospheric oxygen. The experiment contained 128 one inch circular samples: metals, polymers, carbons, and semiconductors. Among metal samples, copper has shown some interesting new results. Two types of copper samples, a film sputter coated on fused silica and a bulk piece of OFHC copper, were characterized employing a variety of techniques such as X-ray and Auger electron spectroscopies, X-ray diffraction, and high resolution profilometry. Cu 2p core level spectra were used to characterize the presence of Cu2O and CuO in addition to Cu Auger LMM lines. These results are supported by our recent X-ray diffraction studies which clearly establish the presence of Cu oxides which we were unable to prove in our earlier work. Profilometry showed an increase in thickness of the film sample where exposed to 106.7 +/- 0.5 nm from an initial thickness of 74.2 +/- 1.1 nm. Further studies with SEM and ellipsometry are underway.

Raikar, Genesh N.↗

The effects of layering in ferroelectric Si-doped HfO{sub 2} thin films

Atomic layer deposited Si-doped HfO{sub 2} thin films approximately 10 nm thick are deposited with various Si-dopant concentrations and distributions. The ferroelectric behavior of the HfO{sub 2} thin films are shown to be dependent on both the Si mol. % and the distribution of Si-dopants. Metal-ferroelectric-insulator-semiconductor capacitors are shown to exhibit a tunable remanent polarization through the adjustment of the Si-dopant distribution at a constant Si concentration. Inhomogeneous layering of Si-dopants within the thin films effectively lowers the remanent polarization. A pinched hysteresis loop is observed for higher Si-dopant concentrations and found to be dependent on the Si layering distribution.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Stable Neutral Atom Trap with a Thin Superconducting Disc

A stable magnetic quadrupole trap for neutral atoms on a superconducting Nb thin-film disc is demonstrated. The quadrupole field is composed of the magnetic field that is generated by vortices on the disc introduced by cooling the disc across the transition temperature with a finite field and an oppositely directed uniform field applied after cooling. The trap is stable when all trapping processes are performed above the dendritic instability temperature T{sub a}. When the field intensity is changed below this temperature, the quadrupole field collapses and the trap disappears. The initial vortex density decreases even when the external field is changed at a temperature T>T{sub a}. However, the vortex density is stabilized at an equilibrium density, whereas at T<T{sub a}, it almost completely disappears. A stable trap can be formed, even when the initial vortices are introduced through a dendritic avalanche.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nanocrystalline ZrN thin film development via atomic layer deposition for U-Mo powder

Zirconium nitride (ZrN) thin film deposited via thermal atomic layer deposition (ALD) has been recently chosen as a candidate technology for application of a diffusion barrier coating on the low enriched uranium alloy powder considered in the NNSA research reactor conversion program. Reported here is the first instance of using ALD for coating actinide materials. For this study, a modified ALD system was constructed to produce one micron thick zirconium nitride (ZrN) coating over spherical particulate of natural uranium-molybdenum (U-Mo) based fuel. The ALD system was designed to have a rotating drum system, with provisions for facilitating sequential exposures of chemicals such as tetrakis dimethyl amido zirconium (TDMAZr) and ammonia (NH 3 ) in order to deposit ZrN. The ALD system was successful in developing a highly conformal ZrN coating covering every individual U-7Mo particle. This article describes the ZrN film synthesis details and reports the produced microstructure and composition of the ALD ZrN as deposited on fuel particulates. The as-fabricated coating was determined to have a nanocrystalline structure in the cubic-ZrN (cF8) phase. It exhibited a dense microstructure with adequate interfacial bonding. TEM-EELS characterization demonstrated that the coating contains a very low amount of oxygen impurity. To understand the potential microstructural evolution for ALD ZrN during reactor operation, an in-situ heavy ion (Kr) irradiation experiment was performed at the IVEM-Tandem facility. A total fluence of 7.5 x 10 15 ions/cm 2 (similar to 10 dpa) was achieved, and apart from minor grain coarsening in the ALD ZrN coating, no significant radiation effects were observed.

36 MATERIALS SCIENCE↗

Physical/chemical properties of tin oxide thin film transistors prepared using plasma-enhanced atomic layer deposition

Thin film transistors (TFTs) with tin oxide films as the channel layer were fabricated by means of plasma enhanced atomic layer deposition (PE-ALD). The as-deposited tin oxide films show n-type conductivity and a nano-crystalline structure of SnO{sub 2}. Notwithstanding the relatively low deposition temperatures of 70, 100, and 130 °C, the bottom gate tin oxide TFTs show an on/off drain current ratio of 10{sup 6} while the device mobility values were increased from 2.31 cm{sup 2}/V s to 6.24 cm{sup 2}/V s upon increasing the deposition temperature of the tin oxide films.

36 MATERIALS SCIENCE↗

Atomic Electron Tomography of Thin Films

In the past decade, the development of atomic electron tomography (AET) [1] has allowed for the 3D characterization of atomic positions in nanoparticle [2], monolayer [3], and needle [4] geometries. Furthermore, many technologically important systems are synthesized and utilized as thin films. Several challenges in sample preparation and data analysis have been overcome to expand the scope of AET to these systems. Polycrystalline yttrium-doped hafnium dioxide (HfO 2 ) was chosen as a model system, because it is technologically relevant as a high capacitance dielectric and ferroelectric.

74 ATOMIC AND MOLECULAR PHYSICS↗

Dysprosium oxide and dysprosium-oxide-doped titanium oxide thin films grown by atomic layer deposition

Dysprosium oxide and dysprosium-oxide-doped titanium oxide thin films were grown by atomic layer deposition on silicon substrates. For depositing dysprosium and titanium oxides Dy(thd){sub 3}-O{sub 3} and TiCl{sub 4}-O{sub 3} were used as precursors combinations. Appropriate parameters for Dy(thd){sub 3}-O{sub 3} growth process were obtained by using a quartz crystal microbalance system. The Dy{sub 2}O{sub 3} films were deposited on planar substrates and on three-dimensional substrates with aspect ratio 1:20. The Dy/Ti ratio of Dy{sub 2}O{sub 3}-doped TiO{sub 2} films deposited on a planar silicon substrate ranged from 0.04 to 0.06. Magnetometry studies revealed that saturation of magnetization could not be observed in planar Dy{sub 2}O{sub 3} films, but it was observable in Dy{sub 2}O{sub 3} films on 3D substrates and in doped TiO{sub 2} films with a Dy/Ti atomic ratio of 0.06. The latter films exhibited saturation magnetization 10{sup −6} A cm{sup 2} and coercivity 11 kA/m at room temperature.

36 MATERIALS SCIENCE↗

Tunable Solid Acid Catalyst Thin Films Prepared by Atomic Layer Deposition

Solid acid catalysts, including zeolites and amorphous silica-aluminas (ASAs), are industrially important materials widely used in the fuel and petrochemical industries. The versatility of zeolites is due to the Brønsted acidity of the bridging hydroxyl and shape selectivity that can be tailored during and after synthesis. This is in contrast to amorphous silica-alumina, where tailoring acidity is a major challenge as the Brønsted acid structure in ASA is still debated. In both cases, however, the pore size and acidity cannot be tuned independently, and this is particularly limiting in the application of biomass conversion, where zeolite pores are too small for the molecules of interest. Herein, we present a method using atomic layer deposition (ALD) to prepare thin films of solid acid materials where the ratio of Brønsted to Lewis acid sites can be tuned precisely. This capability, combined with the sub-nm pore size control afforded by ALD yields a powerful and flexible method for synthesizing solid acid catalysts inside virtually any mesoporous host. We demonstrate the utility of these materials in two acid-catalyzed reactions relevant to biomass conversion: (1) Meerwein–Ponndorf–Verley–Oppenauer (MPVO) reaction and dehydration of fructose and (2) cascade reaction of glucose to 5-hydroxymethylfurfural. Finally, we propose a plausible structure for the Brønsted acid sites in our materials based on infrared spectroscopy and solid-state nuclear magnetic resonance measurements and density functional theory calculations and argue that this same structure might apply to conventional ASAs as well.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of rapid thermal annealing on the structural and local atomic properties of ZnO: Ge nanocomposite thin films

We have investigated the structural and local atomic properties of Ge nanocrystals (Ge-ncs) embedded ZnO (ZnO: Ge) thin films. The films were deposited by sequential sputtering of ZnO and Ge thin film layers on z-cut quartz substrates followed by an ex-situ rapid thermal annealing (RTA) at 600 °C for 30, 60, and 90 s under forming gas atmosphere. Effects of RTA time on the evolution of Ge-ncs were investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), hard x-ray photoelectron spectroscopy (HAXPES), and extended x-ray absorption fine structure (EXAFS). XRD patterns have clearly shown that fcc diamond phase Ge-ncs of sizes ranging between 18 and 27 nm are formed upon RTA and no Ge-oxide peak has been detected. However, cross-section SEM images have clearly revealed that after RTA process, Ge layers form varying size nanoclusters composed of Ge-ncs regions. EXAFS performed at the Ge K-edge to probe the local atomic structure of the Ge-ncs has revealed that as prepared ZnO:Ge possesses Ge-oxide but subsequent RTA leads to crystalline Ge structure without the oxide layer. In order to study the occupied electronic structure, HAXPES has been utilized. The peak separation between the Zn 2p and Ge 3d shows no significant change due to RTA. This implies little change in the valence band offset due to RTA.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Surface smoothing effect of an amorphous thin film deposited by atomic layer deposition on a surface with nano-sized roughness

Previously, Lau (one of the authors) pointed out that the deposition of an amorphous thin film by atomic layer deposition (ALD) on a substrate with nano-sized roughness probably has a surface smoothing effect. In this letter, polycrystalline zinc oxide deposited by ALD onto a smooth substrate was used as a substrate with nano-sized roughness. Atomic force microscopy (AFM) and cross-sectional transmission electron microscopy (XTEM) were used to demonstrate that an amorphous aluminum oxide thin film deposited by ALD can reduce the surface roughness of a polycrystalline zinc oxide coated substrate.

36 MATERIALS SCIENCE↗

Counter-intuitive experimental evidence on the initiation of radical crack in ceramic thin films at the atomic scale

The basic issue related to radial crack in ceramic thin films has received considerable attention due to the fact that the radial crack plays an important role in evaluating the toughness properties of ceramic materials. In this work, an atomic-scale new experimental evidence is clearly presented to reveal the counter-intuitive initiation, the nucleation and the propagation mechanism of the radial crack in Al-Cr-N ceramic thin films.

36 MATERIALS SCIENCE↗

Expanding the Zinc Precursor Toolbox: A Comparative Study of Precursors for Thermal ALD of ZnO Thin Films

Atomic layer deposition (ALD) of zinc oxide (ZnO) has been widely researched using diethyl zinc (DEZ)-based methods. The significant importance of thin films of ZnO as transparent conductive oxides (TCO) in optoelectronic devices and photovoltaics warrants examining alternative Zn precursors for ZnO ALD as potential replacements for the pyrophoric DEZ. In this study, we investigated three alternative Zn precursors: Zn(EEKI)2, Zn(DMP)2, ZnEt(HMDS), in the process development for high-quality ZnO thin films and compared them to DEZ. The ALD processes were studied using in situ spectroscopic ellipsometry. The properties of the ALD ZnO films were characterized using ex situ X-ray photoelectron spectroscopy (XPS), Rutherford backscattering spectrometry and nuclear reaction analysis (RBS/NRA), X-ray diffraction (XRD), atomic force microscopy (AFM), transmission electron microscopy (TEM), and ultraviolet-visible (UV/Vis) spectrophotometry. These measurements confirmed the formation of pure, stoichiometric, and polycrystalline ZnO films using all four Zn precursors. Although the selected precursors are chemically diverse Zn compounds, they all yielded saturating ALD processes and high-quality ZnO thin films at 200 °C. This study highlights the potential benefits of alternative zinc precursors in designing ALD processes for ZnO thin films.

Obenlüneschloß, Jorit↗