SEARCH · Search NASA
Results for “experimental studies”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The effects of outdoor air-side fouling on frost growth and heat transfer characteristics of a microchannel heat exchanger: An experimental study
Air source heat pumps have the potential to efficiently heat and cool buildings, but their effectiveness in many climates is limited by frost growth on the outdoor heat exchanger in heating mode. These heat exchanger coils are also subject to fouling from fibers and particulates outdoors. Frost and fouling have each independently been studied extensively, and newly available research on fouling provides a method to realistically foul the air-side of coils in the laboratory. The current paper uses this method to conduct the first laboratory study of the important interactions between fouling and frost growth for a heat pump outdoor coil. A microchannel heat exchanger is tested clean and fouled, with variations in fouling level, humidity, and initial face velocity of air. Air flow rate is allowed to vary with resistance, and a surprising result is that light fouling increases heat transfer and frost growth rates, even with a 3.5% reduction in initial airflow caused by the fouling. However, heavier fouling decreases both rates. When frost growth is normalized to heat transfer, it is found to be increased by fouling; i.e. the coil’s sensible heat ratio decreases.
Experimental study of sprays with isooctane, hexane, ethanol and their binary mixtures under different flash boiling intensities
Here, this work investigated the behaviors of single-component and multi-component sprays under different flash boiling intensities. Isooctane, hexane, ethanol, isooctane-hexane, and isooctane-ethanol mixtures were used as test fuels. The pressure ratio of the ambient pressure over saturation pressure (R p ) was used as the indicator of the superheated degree. Macroscopic characteristics of the sprays under 10 different R p (1.1 to 0.14) were investigated using Diffused Backlight Imaging (DBI). Droplet size, which revealed the spray microscopic characteristics, was also investigated using Phase Doppler Anemometry (PDA). The results showed that ambient pressure reduction led to higher flash boiling intensity, significant spray morphology changes, and smaller droplet size, regardless of the fuel type and blend ratios. Spray collapse was observed for all sprays once R p dropped below 0.3. Spray collapse dramatically increased the liquid penetration length, expanded the near-field spray angle, and reduced the far-field angle for sprays with all the fuels. Fuel properties, such as the latent heat of vaporization, had significant impacts on droplet size distributions, thus altering the liquid penetration length and spray angles. Under similar R p , sprays with high ethanol content generally had larger droplet sizes compared with other fuel sprays due to the high latent heat of vaporization. The larger droplets caused the high ethanol content sprays to be more resistant to the plume trajectory change, resulting in a smaller far-field spray angle variations with changing R p . At R p of 0.28, sprays with the similar latent heat of vaporization have similar droplet sizes, and droplet sizes at different radial locations were also similar to each other.
Steady-state pool boiling heat transfer experimental studies of horizontally-placed tubes
Not Available
Experimental studies on the effects of sheet resistance and wettability of catalyst layer on electro-catalytic activities for oxygen evolution reaction in proton exchange membrane electrolysis cells
As the most important part of electrochemical reaction in proton exchange membrane electrolysis cells (PEMECs) for water splitting, oxygen evolution reaction (OER) occurs at the anode catalyst layer (CL). The distribution of the OER site is affected by many factors, such as properties of CL, operation parameters, procedures, etc. To study the effects of properties of CLs on the distribution of OER site on the CL, and consequently affect the performance of PEMECs, CLs with different sheet resistances are tested under different operation conditions. Furthermore, the phenomena of OER on CLs are captured by a high-speed and micro-scale visualization system in-situ and analysed coupled with electrochemical results. The results in this work show that both sheet resistance and wettability of CLs have significant impact on the distribution of the OER site, which can help optimize the design of membrane electrode assembly and improve the operating parameters for electrochemical devices.
Spectral induced polarization signatures of smoldering remediation enhanced with colloidal activated carbon: An experimental study
Monitoring the remediation of soil and groundwater contaminated by organic compounds remains highly challenging. The spectral induced polarization (SIP) method exhibits significant promise for monitoring changes to the electrical properties of soils that are undergoing remediation. Thermal treatments, such as smoldering combustion, have become established remediation techniques for destroying contaminants. Smoldering combustion is now being supported by colloidal activated carbon (CAC), with CAC able to adsorb contaminants and supplement the fuel source for destroying contaminants. The objective of this study is to investigate the potential of SIP for tracking the smoldering remediation of imitated field soils supplemented with CAC. SIP column experiments were first conducted to assess the response of SIP to varying concentrations of CAC in field soils that contain, or do not contain, organic material (OM). Here these results demonstrate that increasing OM and CAC contents increase both the real and imaginary components of the complex conductivity, with the imaginary conductivity also showing frequency dependence. Next, a suite of smoldering and SIP column experiments was conducted to investigate if SIP can detect changes in imitated field soils of varying OM and CAC contents that have been remediated by smoldering combustion. The SIP results on the examined soils both before and after smoldering show that SIP can detect changes in the real conductivity, and particularly the imaginary conductivity, between different soil compositions and different stages of the remediation process. High resolution scanning electron microscopy (SEM) imaging was performed on all samples to validate the SIP and smoldering experiments, confirming significant reductions in carbon after smoldering. Overall, this study suggests that SIP has potential to detect changes in the electrical properties of field soils due to the addition of remedial fluids like CAC and contaminant destruction by smoldering remediation.
Internal short circuit and failure mechanisms of lithium-ion pouch cells under mechanical indentation abuse conditions: An experimental study
Electromechanical structural integrity and thermal stability dictate the safety performance of lithium-ion batteries. Progressive deformation and failure across microscopic and macroscopic lengths scales that are responsible for internal short circuit (ISC) in lithium-ion cells under mechanical abuse conditions remains elusive. In this study, a series of indentation tests were conducted on lithium-ion cells with different capacities up to the occurrence of ISC. The external response and internal configuration of these cells were investigated. It is discovered that cells with different capacities and state of charges exhibited different behaviors. Maximum temperature, which is often regarded as the most important parameter related to thermal runaway (TR), varied considerably due to the complicated contact configurations. X-ray computed tomography (XCT) showed that ISC was a collective result of shear band or other strain-localization modes in the electrode assembly, shear offsets in the granular coatings of electrodes, and the accompanying ductile fracture in the metal foils. We believe that the irregular strain-localization modes (kinks, cusps, and buckles), radical mismatches in mechanical properties of different layers, and geometric features of the indenter eventually lead to the tearing/puncture of cell separator at various locations. Furthermore, the results could provide useful guidance for the micromechanical modeling of lithium-ion cells.
Computer-aided tuning of silica/poly(dimethylsiloxane) composites for 3D printing process: A computational and experimental study
Not Available
New experimental studies on the phase diagram of the Al-Cu-Fe quasicrystal-forming system
Not Available
Experimental Study of Acceptor Removal in UFSD
The performance of the Ultra-Fast Silicon Detectors (UFSD) after irradiation with neutrons and protons is compromised by the removal of acceptors in the thin layer below the junction responsible for the gain. In this study, the effect is tested both with capacitance–voltage, C–V, measurements of the doping concentration and with measurements of charge collection, CC, using charged particles. We find a perfect linear correlation between the bias voltage to deplete the gain layer determined with C–V and the bias voltage to collect a defined charge, measured with charge collection. An example for the usefulness of this correlation is presented.
Experimental study of the 34 m Cl beam production at intermediate energies
Here the isomeric content of a 34 Cl beam produced in the intermediate-energy projectile fragmentation of a 150 MeV/u 36 Ar beam on a 3 mm-thick Be target was studied. β-delayed γ-ray spectroscopy was used to measure the population of 34 Cl fragments in the ground vs. isomeric states at zero degrees relative to the incoming primary beam for four different momentum settings of the fragment separator near the predicted central velocity of these fragments, as well as, at two non-zero-degree settings for one momentum setting. Of the settings explored, which excluded rigidities within 0.5% of the value predicted to maximize total 34 Cl yield due to unreacted primary beam, the maximum rate for the production of Cl was found at a rigidity setting 0.75% below the predicted peak 34 Cl yield. The maximum population of the isomeric state relative to the ground state was observed at a rigidity 1.25% below the predicted maximum 34 Cl yield. Studies such as this are important in generating the understanding needed for producing isomer-enriched rare-isotope beams.
Experimental study on fuel depressurization and its effect on dispersion
Not Available
Theoretical and experimental study on the detection limit of the micro-ring resonator based ultrasound point detectors
Not Available
Experimental study on rheological and settling properties of shape memory polymer for fracture sealing in geothermal formations
This article studies the rheology and annular flow of a smart lost circulation material (LCM) at 160 °C, using a high-temperature flow loop. The smart LCM is a shape memory polymer (SMP) that activates at high temperatures, and its particle size increases to seal fractures in geothermal formations. SMP was mixed with the base fluid in two different concentrations, 1.0 and 3.0 wt%, to study rheology, wellbore hydraulics, activation process, and settling behavior under different testing conditions. The results of this study showed that the SMP could be activated at high temperatures. An increase of 80–100% in the particle size was observed at 160 °C. The mud samples showed a high shear-thinning behavior at the two concentrations with a Power-law flow index (n) ranging between 0.025 and 0.101. No additional frictional pressure losses were observed when SMP was added to the base fluid. SMP particles showed an excellent suspension at 1.0 wt% while, at 3.0 wt%, a bed was formed at a low flow rate and without pipe rotation. Increasing the drill pipe rotational speed or flow rate effectively removed the bed and homogeneously dispersed the SMP particles, ensuring a better sealing efficiency. SMP particle dispersion in inclined wells was better than in horizontal wells. Moreover, the findings of this study help optimize the lost circulation treatment by considering a wide range of operating parameters that can further be extended to different systems and geometries.
Evaluation of the critical behavior near ferromagnetic to paramagnetic phase transition in CrTe 1-x Se x alloys: An experimental study
For this study, we used the conventional solid-state reaction method to prepare stoichiometric samples of CrTe 1-x Se x , where 0 ≤ x ≤ 0.10, and investigated the structural and critical behavior of the prepared samples. Room temperature powder X-ray diffraction, along with Rietveld refinement, revealed the emergence of the NiAs structure with P6 3 /mmc (194) space group with increasing Se substitution. The high-temperature linear fit to inverse of the dc-susceptibility versus temperature for the mother sample resulted in an effective moment of 3.65μ B Cr with Curie-Weiss temperature near 335K, which is slightly higher than the Tc of ~332K obtained from the inflection point of magnetization versus temperature. Magnetization isotherms were employed to investigate the critical behavior of ferromagnetic CrTe 1-x Se x with 0.0 ≤ x ≤ 0.10 near their Curie temperatures (Tc). The magnetic behavior near Tc was found to follow 3D mean-field critical exponents with a second-order phase transition in all samples investigated. We fine-tuned the critical exponents (β, γ, and δ) using a combination of an iteration technique, the Kouvel-Fisher method, and modified Arrott plots. All samples follow a mean field behavior, with Tc ranging from 298 to 340K. The acquired values exhibit self-consistency, as indicated by the results from the Widom scaling relation. Furthermore, the magnetization isotherms exhibit a universal scaling behavior, providing additional credence to the calculated critical exponents.