Search NASA⌕ Search

SEARCH · Search NASA

Results for “interface diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

EBR-II Superheater Duplex Tube Examination

After 30 years of operation, the Experimental Breeder Reactor II (EBR-II) Superheater 710 at Argonne National Laboratory-West (now Idaho National Laboratory) was decommissioned. As part of its post-service examination, four duplex tube sections were removed and Charpy impact testing was performed to characterize the crack arresting ability of nickel-bonded tube interfaces. Scanning electron microscopy (SEM) examination was also performed to characterize and identify changes in bond material microstructure. From room temperature to 400 degrees C, all samples demonstrated ductility and crack-stopping ability similar to that exhibited by beginning-of-life samples. However, at low temperature (-5 degrees C), samples removed from the lower region of the superheater (near the sodium inlet) failed while those from the upper region (near the sodium outlet) did not. SEM analysis revealed that all the tube-tube interfaces showed evidence of iron diffusion into the nickel braze, which resulted in the formation of a multiphase diffusion structure. Yet, significant void formation was only observed in the bond layer of the tubes removed from the lower region. This may be due to a change in the crystal microstructure of one of the phases within the bond layer that occurs in the 350 to 450 degrees C temperature range, which results in a lower density and the formation of porosity. Apparently, only the samples from the higher temperature region were exposed to this transition temperature, and the resulting large voids that developed acted as stress concentrators that led to low-temperature embrittlement and failure of the Charpy impact specimens.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Electrode and Microstructure Dependence of Oxygen Diffusion in Ferroelectric Hafnium Zirconium Oxide Thin Films

Hafnia-based ferroelectrics hold promise to reduce energy demand for computing by enabling compute-in-memory and as non-volatile memories. The ferroelectric phase in this material system is, in part, stabilized by oxygen vacancies. While oxygen vacancies may be a necessity for phase stability, they limit device endurance through diffusion and accumulation into conducting channels. Herein, it is shown that oxygen diffusion is spatially variable within individual grains of ferroelectric hafnium zirconium oxide (HZO). Using 18 O tracers and finite difference modeling, it is shown that grain boundaries and regions near electrode interfaces allow for relatively rapid oxygen diffusion, with values as much as 10 4 larger than the grain cores. Further, the selection of electrode material affects the diffusion coefficients across all microstructural regions. HZO films in contact with TiN electrodes result in more oxygen-deficient HZO films and higher oxygen diffusion coefficients. Tungsten electrodes result in fewer vacancies and lower diffusion coefficients. Diffusion activation energy differences between the HZO with the two electrodes is reconciled by differing populations of charged and uncharged oxygen vacancies. This insight into the local vacancy populations and diffusion pathways provides a platform for designing hafnia-based films, deposition processes, and integration strategies to reduce vacancy gradients and improve performance.

36 MATERIALS SCIENCE↗

Resistance switching at the Al/SrTiO{sub 3-x}N{sub y} anode interface

The electroformation and resistance switching behavior of Al/SrTiO{sub 3-x}N{sub y}/Al have been investigated. The resistance of Al/SrTiO{sub 3-x}N{sub y}/Al irreversibly increases when voltages higher than a certain threshold voltage are applied. A bistable resistance switching develops at one of the Al electrodes that performs as the anode. The formation of stacking faults in SrTiO{sub 3-x}N{sub y} during preparation by microwave plasma treatment is a prerequisite for the occurrence of switching as confirmed by site-specific high resolution transmission electron microscopy at the electrode interfaces. The resistance switching effect is discussed by considering the role of stacking fault defects in the oxygen/nitrogen diffusion at the anode metal-oxynitride interface.

36 MATERIALS SCIENCE↗

Liquid and liquid–gas flows at all speeds

All speed flows and in particular low Mach number flow algorithms are addressed for the numerical approximation of the Kapila et al. [1] multiphase flow model. This model is valid for fluid mixtures evolving in mechanical equilibrium but out of temperature equilibrium and is efficient for material interfaces computation separating miscible and non-miscible fluids. In this context, the interface is considered as a numerically diffused zone, captured as well as all present waves (shocks, expansion waves). The same flow model can be used to solve cavitating and boiling flows [2]. Many applications occurring with liquid–gas interfaces and cavitating flows involve a very wide range of Mach number, from 10{sup −3} to supersonic (and even hypersonic) conditions with respect to the mixture sound speed. It is thus important to address numerical methods free of restrictions regarding the Mach number. To do this, a preconditioned Riemann solver is built and embedded into the Godunov explicit scheme. It is shown that this method converges to exact solutions but needs too small time steps to be efficient. An implicit version is then derived, first in one dimension and second in the frame of 2D unstructured meshes. Two-phase flow preconditioning is then addressed in the frame of the Saurel et al. [3] algorithm. Modifications of the preconditioned Riemann solver are needed and detailed. Convergence of both single phase and two-phase numerical solutions are demonstrated with the help of single phase and two-phase steady nozzle flow solutions. Last, the method is illustrated by the computation of real cavitating flows in Venturi nozzles. Vapour pocket size and instability frequencies are reproduced by the model and method without using any adjustable parameter.

42 ENGINEERING↗

A posteriori error analysis for a cut cell finite volume method

We study the solution of a diffusive process in a domain where the diffusion coefficient changes discontinuously across a curved interface. We consider discretizations that use regularly-shaped meshes, so that the interface “cuts” through the cells (elements or volumes) without respecting the regular geometry of the mesh. Consequently, the discontinuity in the diffusion coefficients has a strong impact on the accuracy and convergence of the numerical method. This motivates the derivation of computational error estimates that yield accurate estimates for specified quantities of interest. For this purpose, we adapt the well-known adjoint based a posteriori error analysis technique used for finite element methods. In order to employ this method, we describe a systematic approach to discretizing a cut-cell problem that handles complex geometry in the interface in a natural fashion yet reduces to the well-known Ghost Fluid Method in simple cases. We test the accuracy of the estimates in a series of examples.

97 MATHEMATICS AND COMPUTING↗

Molecular dynamics simulations of evaporation-induced nanoparticle assembly

While evaporating solvent is a widely used technique to assemble nano-sized objects into desired superstructures, there has been limited work on how the assembled structures are affected by the physical aspects of the process. We present large scale molecular dynamics simulations of the evaporation-induced assembly of nanoparticles suspended in a liquid that evaporates in a controlled fashion. The quality of the nanoparticle crystal formed just below the liquid/vapor interface is found to be better at relatively slower evaporation rates, as less defects and grain boundaries appear. This trend is understood as the result of the competition between the accumulation and diffusion times of nanoparticles at the liquid/vapor interface. When the former is smaller, nanoparticles are deposited so fast at the interface that they do not have sufficient time to arrange through diffusion, which leads to the prevalence of defects and grain boundaries. Our results have important implications in understanding assembly of nanoparticles and colloids in non-equilibrium liquid environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Recombination luminescence and trap levels in undoped and Al-doped ZnO thin films on quartz and GaSe (0 0 0 1) substrates

Highlights: Black-Right-Pointing-Pointer ZnO films on GaSe create electron trapping states and PL recombination levels. Black-Right-Pointing-Pointer Zn and Al diffusion in GaSe produces low-energy widening of its PL emission. Black-Right-Pointing-Pointer ZnO:Al films on GaSe lamellas are suitable for gas-discharge lamp applications. -- Abstract: Photoluminescence spectra of ZnO and ZnO:Al (1.00, 2.00 and 5.00 at.%) films on GaSe (0 0 0 1) lamellas and amorphous quartz substrates, obtained by annealing, at 700 K, of undoped and Al-doped metal films, are investigated. For all samples, the nonequilibrium charge carriers recombine by radiative band-to-band transitions with energy of 3.27 eV, via recombination levels created by the monoionized oxygen atoms, forming the impurity band laying in the region 2.00 - 2.70 eV. Al doping induces an additional recombination level at 1.13 eV above the top of the valence band of ZnO films on GaSe substrates. As a result of thermal diffusion of Zn and Al into the GaSe interface layer from ZnO:Al/GaSe heterojunction, electron trap levels located at 0.22 eV and 0.26 eV below the conduction band edge of GaSe, as well as a deep recombination level, responsible for the luminescent emission in the region 1.10 - 1.40 eV, are created.

36 MATERIALS SCIENCE↗

Nonspecifically bound proteins spin while diffusing along DNA

It is known that DNA-binding proteins can slide along the DNA helix while searching for specific binding sites, but their path of motion remains obscure. Do these proteins undergo simple one-dimensional (1D) translational diffusion, or do they rotate to maintain a specific orientation with respect to the DNA helix? We measured 1D diffusion constants as a function of protein size while maintaining the DNA-protein interface. Using bootstrap analysis of single-molecule diffusion data, we compared the results to theoretical predictions for pure translational motion and rotation-coupled sliding along the DNA. The data indicate that DNA-binding proteins undergo rotation-coupled sliding along the DNA helix and can be described by a model of diffusion along the DNA helix on a rugged free-energy landscape. A similar analysis including the 1D diffusion constants of eight proteins of varying size shows that rotation-coupled sliding is a general phenomenon. The average free-energy barrier for sliding along the DNA was 1.1 {+-} 0.2 k{sub B}T. Such small barriers facilitate rapid search for binding sites.

59 BASIC BIOLOGICAL SCIENCES↗

Passivated Contacts for Direct Wafer Product (Final Technical Report)

This TCF project developed a thin-oxide (SiO 2 )/polycrystalline silicon (poly-Si) passivated contact solar cell on CubicPV's (formally 1366 Technologies, Inc.) Direct Wafer® Product (DWP) kerfless wafers. The project used two NREL-developed technologies described in U.S. Patent No. 9,911,873, Hydrogenation of Passivated Contacts and U.S. Patent Application Serial No. 15/890,172, Doped Passivated Contacts . The project was motivated by a potential higher efficiency cell (compared to a PERC cell) using passivated contacts on the ultra-low cost kerfless wafers grown using the Direct Wafer process. The hope was to accelerate market adoption of the cell and wafer by delivering the lowest LCOE in the PV industry. The project tested both n-type and p-type SiO 2 /poly-Si passivated contacts grown by thermal oxidation and plasma enhanced chemical vapor deposition (PECVD) of the poly-Si layer on DWP with varying wafer resistivities. Both deposition techniques are industry standards and thus economically viable methods for commercializing the contacts. The results indicated that both n-type and p-type poly-Si passivated contacts can be formed on polycrystalline DWP wafers, but implied open-circuit voltages (i Voc ) were limited to below 0.65 mV (compared with ~ 730 mV on n-Cz wafers). Diffusion of H to the Si/SiO 2 /poly-Si interface was key to obtaining high i Voc values. In this study, H was diffused from a high-temperature SiN x layer deposited over the poly-Si layer during a high-temperature firing step, similar to one used for screen printed metals. The study concluded that poly-Si passivated contacts on DWP wafers passivated the surface of the wafers as well as PERC passivated surfaces, which use a less expensive dielectric layer stack. The project showed that Direct Wafer Product wafers grown by CubicPV could produce high i Voc values (~0.647 mV), which could produce a cell over 20% efficient with proper processing and metallization. These cells, though not economically viable in 2024 as a stand-alone cell, could be integrated with a wide-bandgap top solar cell to form a two-junction tandem cell that could be viable under certain circumstances. This is because the bottom cell of a 30%, two-terminal tandem only needs to be a 20% cell under one-sun conditions. Thus, the DWP could be an ideal low-cost wafer for tandems. The project also revealed that a TOPCon type cell could be formed on a p-type DWP wafer using a P-diffused emitter and a p-type poly-Si contact. In fact, the p-type version of the poly-Si contact out-performed the n-type version for a variety of wafer resistivities, from highly doped to lowly doped. This curiosity requires more work to understand because on Cz wafers, the n-type poly-Si contact is of much higher quality than the p-type version.

14 SOLAR ENERGY↗

Large lateral photovoltaic effect with ultrafast relaxation time in SnSe/Si junction

In this paper, we report a large lateral photovoltaic effect (LPE) with ultrafast relaxation time in SnSe/p-Si junctions. The LPE shows a linear dependence on the position of the laser spot, and the position sensitivity is as high as 250 mV mm{sup −1}. The optical response time and the relaxation time of the LPE are about 100 ns and 2 μs, respectively. The current-voltage curve on the surface of the SnSe film indicates the formation of an inversion layer at the SnSe/p-Si interface. Our results clearly suggest that most of the excited-electrons diffuse laterally in the inversion layer at the SnSe/p-Si interface, which results in a large LPE with ultrafast relaxation time. The high positional sensitivity and ultrafast relaxation time of the LPE make the SnSe/p-Si junction a promising candidate for a wide range of optoelectronic applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Critical issues in the formation of quantum computer test structures by ion implantation

The formation of quantum computer test structures in silicon by ion implantation enables the characterization of spin readout mechanisms with ensembles of dopant atoms and the development of single atom devices. We briefly review recent results in the characterization of spin dependent transport and single ion doping and then discuss the diffusion and segregation behaviour of phosphorus, antimony and bismuth ions from low fluence, low energy implantations as characterized through depth profiling by secondary ion mass spectrometry (SIMS). Both phosphorus and bismuth are found to segregate to the SiO2/Si interface during activation anneals, while antimony diffusion is found to be minimal. An effect of the ion charge state on the range of antimony ions, 121Sb25+, in SiO2/Si is also discussed.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Analysis of Axial Growth of Gold Indide by Indium Diffusing away from Solder Mounds and Creating the Gold to Gold-Indide Interface Angle Inside the Solder Mound

The interfacial angle between gold and gold-indide in gold wires at the edge of PbSnIn (37.5,37.5,25.) solder mounds has been deduced by measuring the reduction in gold-wire length caused by “axial” gold-indide growth along the surface of gold wires outside the solder mounds and comparing that growth to the known “radial” gold-indide growth inside the solder mound. That interfacial angle has been found to be, on average, thirty degrees independent of temperature for samples aged between ninety and sixty degrees for 3.9 months, but shows large scatter, from a minimum of fifteen degrees for fast axial gold-indide growth, to a maximum of ninety degrees for fast gold-indide growth.

36 MATERIALS SCIENCE↗

Coupled diffusion in lipid bilayers upon close approach

Biomembrane interfaces create regions of slowed water dynamics in their vicinity. When two lipid bilayers come together, this effect is further accentuated, and the associated slowdown can affect the dynamics of larger-scale processes such as membrane fusion. We have used molecular dynamics simulations to examine how lipid and water dynamics are affected as two lipid bilayers approach each other. These two interacting fluid systems, lipid and water, both slow and become coupled when the lipid membranes are separated by a thin water layer. We show in particular that the water dynamics become glassy, and diffusion of lipids in the apposed leaflets becomes coupled across the water layer, while the “outer” leaflets remain unaffected. This dynamic coupling between bilayers appears mediated by lipid–water–lipid hydrogen bonding, as it occurs at bilayer separations where water–lipid hydrogen bonds become more common than water–water hydrogen bonds. We further show that such coupling occurs in simulations of vesicle–vesicle fusion prior to the fusion event itself. As a result, such altered dynamics at membrane–membrane interfaces may both stabilize the interfacial contact and slow fusion stalk formation within the interface region.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Self-consistent modeling of electrochemical strain microscopy of solid electrolytes

Electrochemical strain microscopy (ESM) employs a strong electromechanical coupling in solid ionic conductors to map ionic transport and electrochemical processes with nanometer-scale spatial resolution. To elucidate the mechanisms of the ESM image formation, we performed self-consistent numerical modeling of the electromechanical response in solid electrolytes under the probe tip in a linear, small-signal regime using the Boltzmann–Planck–Nernst–Einstein theory and Vegard's law while taking account of the electromigration and diffusion. We identified the characteristic time scales involved in the formation of the ESM response and found that the dynamics of the charge carriers in the tip-electrolyte system with blocking interfaces can be described as charging of the diffuse layer at the tip-electrolyte interface through the tip contact spreading resistance. At the high frequencies used in the detection regime, the distribution of the charge carriers under the tip is governed by evanescent concentration waves generated at the tip-electrolyte interface. The ion drift length in the electric field produced by the tip determines the ESM response at high frequencies, which follows a 1/f asymptotic law. The electronic conductivity, as well as the electron transport through the electrode-electrolyte interface, do not have a significant effect on the ESM signal in the detection regime. The results indicate, however, that for typical solid electrolytes at room temperature, the ESM response originates at and contains information about the very surface layer of a sample, and the properties of the one-unit-cell-thick surface layer may significantly contribute to the ESM response, implying a high surface sensitivity and a high lateral resolution of the technique. On the other hand, it follows that a rigorous analysis of the ESM signals requires techniques that account for the discrete nature of a solid.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Shock-driven kinetic and diffusive mix in high-Z pusher ICF designs

Revolver and Double Shell Inertial Confinement Fusion capsule designs hope to achieve a robust volumetric thermonuclear burn via the use of a high-Z pusher shell filled with a cryogenic D–T fuel. Unfortunately, mix of the pusher material into the fuel (gas) may adversely impact the burn performance. Hydrodynamic instability of the metal/gas interface as the mix source is an obvious concern, but 1D effects may also be detrimental. Such effects include plasma diffusion at material interfaces, which has been the subject of numerous theoretical, computational, and experimental investigations. However, other 1D mix mechanisms may exist, which have yet to be thoroughly explored. In particular, plasma kinetic effects may drive the mix when a shock breaks out of the metal/gas interface. Using the state-of-the-art, hybrid (kinetic-ion/fluid electron), multi-ion Vlasov–Fokker–Planck code, iFP, we show herein that shock-driven kinetic effects can reconfigure the interface and the interfacial width subsequently grows diffusively. Finally, we consider any implications for high-Z pusher designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Laser Welding-Brazing of Immiscible AZ31B Mg and Ti-6Al-4V Alloys Using an Electrodeposited Cu Interlayer

Metallurgical bonding between immiscible system AZ31B magnesium (Mg) and Ti-6Al-4V titanium (Ti) was achieved by adding Cu interlayer using laser welding-brazing process. Effect of the laser power on microstructure evolution and mechanical properties of Mg/Cu-coated Ti joints was studied. Visually acceptable joints were obtained at the range of 1300 to 1500 W. The brazed interface was divided into three parts due to temperature gradient: direct irradiation zone, intermediate zone and seam head zone. Ti{sub 3}Al phase was produced along the interface at the direct irradiation zone. Ti-Al reaction layer grew slightly with the increase in laser power. A small amount of Ti{sub 2}(Cu,Al) interfacial compounds formed at the intermediate zone and the (α-Mg + Mg{sub 2}Cu) eutectic structure dispersed in the fusion zone instead of gathering when increasing the laser power at this zone. At the seam head zone, Mg-Cu eutectic structure was produced in large quantities under all cases. Joint strength first increased and then decreased with the variation of the laser power. The maximum fracture load of Mg/Cu-coated Ti joint reached 2314 N at the laser power of 1300 W, representing 85.7% joint efficiency when compared with Mg base metal. All specimens fractured at the interface. The feature of fracture surface at the laser power of 1100 W was characterized by overall smooth surface. Obvious tear ridge and Ti{sub 3}Al particles were observed at the fracture surface with increase in laser power. It suggested atomic diffusion was accelerated with more heat input giving rise to the enhanced interfacial reaction and metallurgical bonding in direct irradiation zone, which determined the mechanical properties of the joint.

36 MATERIALS SCIENCE↗

PLASMA DYNAMICS AT THE PROMINENCE-CORONA INTERFACE

The interface between the cool and dense plasma typical of a prominence and its tenuous and hot surrounding coronal plasma is poorly understood. We study the plasma dynamics at this interface using a three-dimensional particle-in-cell code, which enables us to carry out simulations on spatial and temporal scales of the order of the Debye length and plasma period, respectively. The results show that anomalous Bohm diffusion across magnetic field lines occurs at the interface, leading to mixing of the two plasmas. It is also shown that collisions with neutral hydrogen within the prominence plasma are of little importance for the plasma dynamics in the prominence-corona transition region. In particular, the temperature of the prominence plasma crossing the interface into the corona can become anisotropic due to preferential heating by instabilities originating from unstable velocity distributions. Our results pertain to spatial scales significantly smaller than scales commonly used in magnetohydrodynamic simulations, and they shed light on processes that are very likely to be present at the interface.

79 ASTRONOMY AND ASTROPHYSICS↗

Correlation of interface roughness for ion beam sputter deposited W/Si multilayers

W/Si multilayers having 5, 7, 9, 13, 17, and 25 layers have been deposited on c-Si substrates by Ion Beam Sputtering technique and have been characterized by specular and diffused grazing incidence X-ray reflectivity measurements. Information regarding the density, thickness and interface widths of individual layers of the multilayer stacks have been obtained from the theoretical fitting of the specular reflectivity spectra while fitting of the diffused X-ray reflectivity have yielded information regarding roughness and diffusivity at the individual interfaces along with the in-plane correlation lengths of roughness of the individual layers and the vertical correlation length of the whole multilayer structure. Investigations have been carried out on the different behavior of W-on-Si and Si-on-W interfaces and on the variation of the above parameters with the increase in number of layers in the multilayer structures.

36 MATERIALS SCIENCE↗