Search NASA⌕ Search

SEARCH · Search NASA

Results for “FRACTURE PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Effect of metallurgical structure and properties on adhesion and friction behavior of cobalt alloys

The metallurgical structure and some of the mechanical properties of two cobalt alloys, cobalt-50% iron and cobalt-25% molybdenum-10% chromium, were determined under various heat treated conditions. The mechanical properties of the bcc disordered Co-50Fe alloy, which was found to be very brittle, indicated an exceedingly low fracture strength, low hardness, and very weak grain boundary strength. Ordering by suitable heat treatment only produced a more brittle material with a lower fracture strength and a slightly higher hardness value. Work hardening was found to produce a finer grain structure and a greater grain boundary strength. Tensile properties were examined. It was found that the Co-25Mo-10Cr alloy was difficult to place in the alpha Co solid solution condition, which limited the ability to use precipitation as a hardening reaction. Over two hundred adhesion cycles from zero contact load, to maximum load, to fracture were conducted between couples for each of the above alloys in an ultrahigh vacuum system which would permit the sample surfaces to be cleaned of all contaminant layers. In the Co-50Fe case, the calculated fracture stress from the adhesion tests showed values in the range of 80 to 150 k.s.i., which is about ten times greater than the values from tension tests.

Keller, D. V., Jr.↗
NASA NTRS1991

Microfracture in high temperature metal matrix laminates

Computational simulation procedures are described to evaluate the composite microfracture behavior, establish the hierarchy/sequence of fracture modes, and the influence of compliant layers and partial debonding on composite properties and microfracture initiation. These procedures are based upon three-dimensional finite element analysis and composite micromechanics equations. Typical results for the effects of compliant layers and partial debonding, microfracture initiation, and propagation and the thermomechanical cyclic loading on a SiC/Ti15 composite system are presented and discussed. The results show that interfacial debonding follows fiber or matrix fracture, and the thermomechanical cyclic loading severely degrades the composite integrity.

Mital, Subodh K.↗
DOE OSTI2020

Are we modeling the properties of unconventional shales correctly?

Technological advancements have led to impressive growth in hydrocarbon (HC) production from unconventional shale reservoirs. However, major limiting factors in shale gas development are i) low recovery of gas in place (<20%), (ii) a rapid decline in well productivity, iii) release of contaminants, despite the use of advanced hydraulic fracturing fluids and multiple fracturing stages. This is mainly due to a lack of understanding of the nanoscale physicochemical properties of shales, especially that of kerogen, the macromolecule that is not only the source of the majority of the HC’s in shales but also holds most of the HC’s in adsorbed state. Over the last few years, a large number of studies have been published on simulating the physicochemical properties of shale utilizing molecular models of kerogen. However, the molecular models of kerogen input into these simulations are based on the kerogen “type” derived from a very limited number of shale samples. In this paper, we examine the variations that can exist in kerogen structure within a particular kerogen “type” across different shale basins and single shale basin at similar thermal maturity levels. We propose that using kerogen “type” based structural models for molecular simulations could lead to inaccurate estimation of HC reserves, HC recovery, HC production, frackability, and quantity and quality of produced water. Our study highlights the need for developing a better classification of kerogen based on its “molecular structure” instead of “type” for a more accurate prediction of physicochemical properties of shales.

04 OIL SHALES AND TAR SANDS↗
NASA NTRS1989

Influence of dissolved hydrogen on aluminum-lithium alloy fracture behavior

The objective of this work is to study the effects of dissolved hydrogen on the mechanical properties of 2090 and 2219 alloys. Prior to mechanical testing, potentiostatic and potentiodynamic tests were performed using NaCl/HCl solutions varying in pH from 1.5 to 7.5 (3.5 pct NaCl in deionized water). After analysis of the potentiodynamic curve for each solution, several potentiostatic experiments were conducted for various times (from 10 minutes to several hours) with a cathodic overpotential of 300 mV. These experiments were performed to select charging conditions. It is shown that the fracture of L-S and T-S orientations proceeds via slipping of layers in the S-T direction. The T-S and L-S orientations fractured with substantially higher propagation energy that the L-T and T-L orientations, due in large part to the extensive delamination propagation of the fracture.

Rivet, F. C.↗
NASA NTRS1991

Tension, Compression, and Bend Properties for Sic/RBSN Composites

The room-temperature tension, compression, and bend properties of unidirectional SiC fiber-reinforced reaction-bonded silicon nitride composites (SiC/RBSN) have been investigated. The effects of fiber content on the modulus, first matrix cracking strength, and ultimate strength properties were determined. In tension, composites with greater than 8-percent fiber content showed strain capability beyond matrix fracture and fiber-dominated ultimate strength. In compression, the composites displayed essentially elastic behavior, and matrix-dominated ultimate strength. For both deformation modes, most mechanical properties increased with fiber content. In bend, the modulus, strength properties, and failure modes of the composites were influenced by span-to-thickness ratio.

Bhatt, Ramakrishna T.↗
DOE OSTI2024

Splitting tensile strength of shale cores: intact versus fractured and sealed with ureolysis-induced calcium carbonate precipitation (UICP)

Ureolysis-induced calcium carbonate precipitation (UICP) is a biomineral solution where the urease enzyme converts urea and calcium into calcium carbonate. The resulting biomineral can bridge gaps in fractured shale, reduce undesired fluid flow, limit fracture propagation, better store carbon dioxide, and potentially enhance well efficiency. The mechanical properties of shale cores were investigated using a modified Brazilian indirect tensile strength test. An investigation of intact shale using Eagle Ford and Wolfcamp cores was conducted at varying temperatures. Results show no significant difference between shale types (average tensile strength = 6.19 MPa). Eagle Ford displayed higher strength at elevated temperature, but temperature did not influence Wolfcamp. Comparatively, cores with a single, lengthwise heterogeneous fracture were sealed with UICP and further tested for tensile strength. UICP was delivered via a flow-through method which injected 20–30 sequential patterns of ureolytic microorganisms and UICP-promoting fluids into the fracture until permeability reduced by three orders of magnitude or with an immersion method which placed cores treated with guar gum and UICP-promoting fluids into a batch reactor, demonstrating that guar gum is a suitable inclusion and may reduce the number of flow-through injections required. Tensile results for both delivery methods were variable (0.15–8 MPa), and in some cores the biomineralized fracture split apart, possibly due to insufficient sealing and/or heterogeneity in the composite UICP-shale cores. Notably in other cores the biomineralized fracture remained intact, demonstrating more cohesion than the surrounding shale, indicating that UICP may produce a strong seal for subsurface application.

58 GEOSCIENCES↗
NASA NTRS1990

An analytical investigation of delamination front curvature in double cantilever beam specimens

An analytical investigation is conducted to determine the shape of a growing delamination and the distribution of the energy release rate along the delamination front in a laminated composite double cantilever beam specimen. Distributions of the energy release rate for specimens with straight delamination fronts and delamination front contours for delaminations whose growth is governed by the fracture criterion that G = Gc at all points are predicted as a function of material properties and delamination length. The predicted delamination front contours are utilized to ascertain the effect of the changing shape of the delamination front on the value of the critical strain energy release rate as computed from double cantilever beam fracture toughness test data.

Davidson, B. D.↗
NASA NTRS2013

Fracture in Phenolic Impregnated Carbon Ablator

This paper describes the development of a novel technique to understand the failure mechanisms inside thermal protection materials. The focus of this research is on the class of materials known as phenolic impregnated carbon ablators. It has successfully flown on the Stardust spacecraft and is the thermal protection system material chosen for the Mars Science Laboratory and SpaceX Dragon spacecraft. Although it has good thermal properties, structurally, it is a weak material. To understand failure mechanisms in carbon ablators, fracture tests were performed on FiberForm(Registered TradeMark) (precursor), virgin, and charred ablator materials. Several samples of these materials were tested to investigate failure mechanisms at a microstructural scale. Stress-strain data were obtained simultaneously to estimate the tensile strength and toughness. It was observed that cracks initiated and grew in the FiberForm when a critical stress limit was reached such that the carbon fibers separated from the binder. However, both for virgin and charred carbon ablators, crack initiation and growth occurred in the matrix (phenolic) phase. Both virgin and charred carbon ablators showed greater strength values compared with FiberForm samples, confirming that the presence of the porous matrix helps in absorbing the fracture energy.

Agrawal, Parul↗
NASA NTRS1985

Fundamental Studies of Low Velocity Impact Resistance of Graphite Fiber Reinforced Polymer Matrix Composites

A study was conducted to relate the impact resistance of graphite fiber reinforced composites with matrix properties through gaining an understanding of the basic mechanics involved in the deformation and fracture process, and the effect of the polymer matrix structure on these mechanisms. It was found that the resin matrix structure influences the composite impact resistance in at least two ways. The integration of flexibilizers into the polymer chain structure tends to reduce the T sub g and the mechanical properties of the polymer. The reduction in the mechanical properties of the matrix does not enhance the composite impact resistance because it allows matrix controlled failure to initiate impact damage. It was found that when the instrumented dropweight impact tester is used as a means for assessing resin toughness, the resin toughness is enhanced by the ability of the clamped specimen to deflect enough to produce sufficient membrane action to support a significant amount of the load. The results of this study indicate that crossplied composite impact resistance is very much dependent on the matrix mechanical properties.

Bowles, K. J.↗
NASA NTRS1981

Research on graphite reinforced glass matrix composites

A broad group of fibers and matrices were combined to create a wide range of composite properties. Primary material fabrication procedures were developed which readily permit the fabrication of flat plate and shaped composites. Composite mechanical properties were measured under a wide range of test conditions. Tensile, flexure mechanical fatigue, thermal fatigue, fracture toughness, and fatigue crack growth resistance were evaluated. Selected fiber-matrix combinations were shown to maintain their strength at up to 1300 K when tested in an inert atmosphere. Composite high temperature mechanical properties were shown to be limited primarily by the oxidation resistance of the graphite fibers. Composite thermal dimensional stability was measured and found to be excellent.

Prewo, K. M.↗
DOE OSTI2020

Characterization of elastic mechanical properties of Tuscaloosa Marine Shale from well logs using the vertical transversely isotropic model

To avoid steep declines in the Tuscaloosa Marine Shale (TMS) production, wells are fracture-stimulated to release the hydrocarbons trapped in the matrix of the formation. An accurate estimation of Young’s modulus and Poisson’s ratio is essential for hydraulic fracture propagation. In addition, ignoring the highly heterogeneous and anisotropic character of TMS can lead to erroneous stress values, which subsequently affect hydraulic fracture width estimates and the overall hydraulic fracturing process. We have developed an empirical 1D geomechanical model that takes into account VTI anisotropy, and it is used to characterize the elastic mechanical properties of TMS in two wells. In the analyzed formation, the vertical Poisson’s ratio is less than the horizontal Poisson’s ratio, which suggests the necessity of an alternative to the ANNIE equations. The stiffness coefficients [Formula: see text] and [Formula: see text] were estimated using the relationships developed from the ultrasonic core data available for the two TMS. Further, correlations between the static and dynamic properties from laboratory tests were used to improve the minimum horizontal stress calculation. We compare VTI Young’s moduli, Poisson’s ratios, and minimum horizontal stress with the isotropic solution. VTI modeling improves the estimation of the elastic mechanical properties. The isotropic solution underestimates the minimum horizontal stress in the formation. Moreover, it was shown that the 20 ft shale interval below the TMS base is characterized by a low Young’s modulus (the vertical Young’s modulus is equal to 20 GPa, whereas the horizontal Young’s modulus is equal to 40 GPa) and may be a frac barrier.

Geochemistry & Geophysics↗
DOE OSTI2026

A point-particle-based hydride shell-shedding model for ejecta particle transport in reactive environments

A shock wave passing over a rough or perturbed metal surface will induce a limiting case of Richtmyer–Meshkov instability and will cause small particles to eject from the surface and transport into the surrounding medium. These particles are known as ejecta and can be either solid or liquid in nature. Recent experiments have shown that liquid cerium ejecta clouds exhibit unexpected non-monotonic acceleration behaviors as well as temperature plateaus after a brief temperature rise if they are transporting in a chemically reactive, hydrogen-based medium while they act as expected in an inert medium. This work details a point-particle model developed for reactive cerium ejecta transport, which attempts to account for these new physics through the behavior of a developing solid hydride shell, which is believed to form as a product of the reaction. The overall model incorporates the effects of the reaction on the particle properties as well as the effects of potential shedding of the shell into sub-micrometer scale flakes and potential phase change of the hydride if the ejecta particles reach the melt point of the hydride layer. The model is tested by performing simulations of the original motivating experiments and comparing quantities, such as ejected mass, velocimetry, and temperature profiles, against the experimental data. While the model is able to capture many general features of the observed anomalies, some inaccuracies still exist. These point to both missing physics in the model (such as a deuterium adsorption mechanism on the hydride layer) as well as a lack of knowledge of certain material properties (such as the strength of cerium hydride to determine dynamic fracture thicknesses) needed to fully reduce the uncertainties in the model by up to an order of magnitude and perform a true attempt at model validation.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Microstructure based modeling of friction stir welded joint of dissimilar metals using crystal plasticity

We report the friction stir welding (FSW) process shows promising results in joining dissimilar metals which are otherwise almost impossible to join using traditional welding techniques. Being a new technique, the deformation and the failure mechanism of the joints made by the FSW process needs to be investigated. In this work, a joint between AZ31 Mg alloy and DP590 steel is modeled using phenomenological crystal plasticity formulation on the mesoscale in the form of a representative volume element (RVE). The interface of the two materials is modeled using a cohesive zone model. A parametric study has been performed to understand the effect of grain size and interface fracture toughness as well as strength on the mechanical performance of the joint. It was found that the grain size of AZ31 Mg alloy, as well as DP590 steel, has little effect on the overall joint performance. On the other hand, interface fracture toughness and strength have a significant impact on the mechanical properties of the joint

36 MATERIALS SCIENCE↗
DOE OSTI2025

Processes in Salt Repositories for Radioactive Waste Disposal

This document summarizes the key processes (thermal, hydrological, mechanical, and chemical; THMC) impacting the features of a deep geological repository for radioactive waste in salt. Some processes are natural and on-going whether the repository is there or not, and other processes are driven by the perturbation associated with the repository. The features considered here include both engineered and natural components of the repository system. The engineered barrier system (EBS) in a salt repository is quite different from those implemented for a repository in clay or crystalline rocks, because it is comprised mostly of granular salt and salt-compatible cements, rather than bentonite. When compared to other rocks (i.e., silicates), salt has unique properties that make it an excellent potential host rock. Openings and fractures in salt creep closed readily. Salt has high thermal conductivity, which can reduce peak temperatures. Additionally, far away from the excavations the porosity of salt is unconnected, which leads to essentially zero advective or diffusive transport. The small amount of hypersaline brine occurring in salt minimizes microbial activity, reduces colloid-assisted transport, and eliminates in-package criticality (i.e., chloride is a neutron poison). At the end of the report, we present a brief outline for a potential salt repository, including considerations avoided in previous repository disposal concepts. We propose considering higher-temperature processes in future disposal concepts, rather than trying to minimize the thermal perturbation of the repository. Since hot salt is drier, a dry repository would limit corrosion, gas generation, and solute transport. Openings and fractures creep shut faster in hot salt. Therefore, higher temperatures could be seen as beneficial, rather than something to minimize, through increased spacing between waste packages (increasing repository costs).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1973

Properties of materials in high pressure hydrogen at cryogenic, room, and elevated temperatures

Various tests were conducted to determine the mechanical properties of 12 alloys that are commonly used or proposed for use in pressurized gaseous hydrogen or hydrogen containing environments. Properties determined in the hydrogen environments were compared to properties determined in a pure helium environment at the same conditions to establish environmental degradation. The specific mechanical properties tested include: high-cycle fatigue, low-cycle fatigue, fracture mechanics, creep-rupture, and tensile.

Harris, J. A., Jr.↗
NASA NTRS1975

Lunakhod-2: Preliminary research results

Results from the Lunakhod 2 experiment on the surface property variations and relief structure of lunar craters are presented. Tectonic fractures, iron composition of lunar rocks, magnetic measurements, lunar sky brightness, and corpuscular radiation of the lunar body were studied.

Vinogradov, A. P.↗
NASA NTRS1980

Adhesion, friction, and wear of binary alloys in contact with single-crystal silicon carbide

Sliding friction experiments, conducted with various iron base alloys (alloying elements are Ti, Cr, Mn, Ni, Rh and W) in contact with a single crystal silicon carbide /0001/ surface in vacuum are discussed. Results indicate atomic size misfit and concentration of alloying elements play a dominant role in controlling adhesion, friction, and wear properties of iron-base binary alloys. The controlling mechanism of the alloy properties is as an intrinsic effect involving the resistance to shear fracture of cohesive bonding in the alloy. The coefficient of friction generally increases with an increase in solute concentration. The coefficient of friction increases as the solute-to-iron atomic radius ratio increases or decreases from unity. Alloys having higher solute concentration produce more transfer to silicon carbide than do alloys having low solute concentrations. The chemical activity of the alloying element is also an important parameter in controlling adhesion and friction of alloys.

Miyoshi, K.↗
NASA NTRS1981

Experiment K307: Vertebral body strength of rat spinal columns

The effects of space flight on vertebral body bone strength excised were investigated. Comparative biomechanical investigations of vertebral body strength for flight, synchronous, and vivarium rats following spacecraft recovery (R+0), at R+6 and R+29 days post flight recovery are presented. Statistical analyses are presented for the mechanical properties of stiffness, ultimate load, displacement to ultimate load, and energy to ultimate load. At R+0 all of the above properties show that the vertebral body exhibits an increasing susceptibility to fracture. The reduction of bone strength is inhomogeneous and dependent on vertebral level. The R+6 recovery data was inconclusive since it varied above and below the R+0 data. At R+29 ultimate load values showed a statistically significant increase in bone strength approaching that of the vivarium or control group.

Kazarian, L. E.↗