SEARCH · Search NASA

Results for “Kinetic methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Techniques for increasing boron fiber fracture strain

Improvement in the strain-to-failure of CVD boron fibers is shown possible by contracting the tungsten boride core region and its inherent flaws. The results of three methods are presented in which etching and thermal processing techniques were employed to achieve core flaw contraction by internal stresses available in the boron sheath. After commercially and treatment induced surface flaws were removed from 203 micrometers (8 mil) fibers, the core flaw was observed to be essentially the only source of fiber fracture. Thus, fiber strain-to-failure was found to improve by an amount equal to the treatment induced contraction on the core flaw. Commercial feasibility considerations suggest as the most cost effective technique that method in which as-produced fibers are given a rapid heat treatment above 700 C. Preliminary results concerning the contraction kinetics and fracture behavior observed are presented and discussed both for high vacuum and argon gas heat treatment environments.

Dicarlo, J. A.↗

NASA NTRS1977

Techniques for increasing boron fiber fracture strain

Improvement in the strain-to-failure of chemical-vapor-deposition boron fibers is shown possible by contracting the tungsten boride core region and its inherent flaws. Results of three methods are presented in which etching and thermal-processing techniques were employed to achieve core flaw contraction by internal stresses available in the boron sheath. After commercially and treatment-induced surface flaws were removed from 203-micron (8-mil) fibers, the core flaw was observed to be essentially the only source of fiber fracture. Thus, fiber strain-to-failure was found to improve by an amount equal to the treatment-induced contraction on the core flaw. To date, average fracture strains and stresses greater than 1.4% and 5.5 GN/sq m (800 ksi), respectively, have been achieved. Commercial feasibility considerations suggest as the most cost-effective technique that method in which as-produced fibers are given a rapid heat treatment above 700 C. Preliminary results concerning the contraction kinetics and fracture behavior observed with this technique are presented and discussed for both high-vacuum and argon-gas heat-treatment environments.

Dicarlo, J. A.↗

NASA NTRS1979

Recent developments in liquid-metal embrittlement

The paper reviews developments in liquid-metal embrittlement of the past 7 years including data on cyclic loading. Embrittlement by solid and liquid metals and by hydrogen has many common features, although the mechanism of embrittler transport differs. Fracture may occur in each type of embrittlement by environmentally assisted shear and by reduced cohesion; embrittlement under cyclic loading has been widely observed, with stress level, temperature, and substrate alloy composition and grain size being the major variables. The degree of embrittlement between any combination of environment (i.e. hydrogen, liquid metal, or solid metal) and substrate depends upon the strength of the interaction with the substrate, the kinetics of embrittler transport, the mutual solubility of embrittler and substrate, and a large number of test and microstructural conditions. A method of calculating the most significant of these variables and the strength of interaction was reviewed and predictions of embrittlement in previously untested couples were made.

Stoloff, N. S.↗

NASA NTRS1984

Laser-induced volatilization and ionization of microparticles

A method for the laser vaporization and ionization of individual micron-size particles is presented whereby a particle is ionized by a laser pulse while in flight in the beam. Ionization in the beam offers a real-time analytical capability and eliminates any possible substrate-sample interferences during an analysis. An experimental arrangement using a high-energy Nd-YAG laser is described, and results are presented for ions generated from potassium biphthalate particles (1.96 micron in diameter). The method proposed here is useful for the chemical analysis of aerosol particles by mass spectrometry and for other spectroscopic and chemical kinetic studies.

Sinha, M. P.↗

NASA NTRS1991

Sodium-metal chloride battery research at JPL

Sodium - metal chloride batteries have certain distinct advantages over sodium - sulfur batteries such as increased safety, inherent overcharge capability and lower operating temperatures. Two systems, i.e., Na/FeCl2 and Na/NiCl2 were developed extensively elsewhere and evaluated for various applications including electric vehicles and space. Their performance has been very encouraging and prompted a detailed fundamental study on these cathodes here at the Jet Propulsion Laboratory. A brief review of our studies on these new cathode materials is presented here. The initial efforts focused on the methods of fabrication of the electrodes and their electrochemical characterization." Subsequent studies were aimed at establishing the reaction mechanism, determining the kinetics and identifying the rate-limiting processes in the reduction of metal chloride cathodes. Nickel chloride emerged from these studies as the most promising candidate material and was taken up for further detailed study on its passivation - a rate limiting process - under different experimental conditions. Also, the feasibility of using copper chloride, which is expected to have higher energy density, has been assessed. Based on the criteria established from the voltametric response of FeCl2, NiCl2 and CuCI2, several other transition metal chlorides were screened. Of these, molybdenum and cobalt chlorides appear promising.

B V Ratnakumar↗

NASA NTRS1992

Energy expenditure in space flight (doubly labelled water method) (8-IML-1)

The objective of the Energy Expenditure in Space Flight (ESS) experiment is to demonstrate and evaluate the doubly labeled water method of measuring the energy expended by crew members during approximately 7 days in microgravity. The doubly labeled water technique determines carbon dioxide production which is then used to calculate energy expenditure. The method relies on the equilibrium between oxygen in respiratory carbon dioxide and oxygen in body water. Because of this equilibrium, the kinetic of water turnover and respiration are interdependent. Under normal conditions, man contains small but significant amounts of deuterium and oxygen 18. Deuterium is eliminated from the body as water while oxygen 18 is eliminated as water and carbon dioxide. The difference in the turnover rates in the two isotopes is proportional to the carbon dioxide production. Deliberately enriching the total body water with both of these isotopes allows the isotope turnovers to be accurately measured in urine, plasma, or saliva samples. The samples are taken to the laboratory for analysis using an ion-ratio spectrometer.

Parsons, Howard G.↗

NASA NTRS1993

Computation of unsteady shock-induced combustion using logarithmic species conservation equations

Numerical simulations are used to investigate periodic combustion instabilities observed in ballistic-range experiments of blunt bodies flying at supersonic speeds through hydrogen-air mixtures. The computations are validated by comparing experimental shadowgraphs with shadowgraphs created from the computed flowfields and by comparing the experimentally measured instability frequencies with computed frequencies. The numerical simulations use a logarithmic transformation of the species conservation equations as a way to reduce the grid requirements for computing shock-induced combustion. The transformation is applied to the Euler equations coupled to a detailed hydrogen-air chemical reaction mechanism with 13 species and 33 reactions. The resulting differential equations are solved using a finite volume formulation and a two-step predictor-corrector scheme to advance the solution in time. Results are presented and compared for both a flux-vector splitting scheme and an upwind TVD scheme. The computations add insight to the physical processes observed in the experiments and the numerical methods needed to simulate them. The usefulness of the ballistic-range experiments for the validation of numerical techniques and chemical kinetic models is also demonstrated.

Wilson, Gregory J.↗

NASA NTRS1995

Verification of a three-dimensional resin transfer molding process simulation model

Experimental evidence was obtained to complete the verification of the parameters needed for input to a three-dimensional finite element model simulating the resin flow and cure through an orthotropic fabric preform. The material characterizations completed include resin kinetics and viscosity models, as well as preform permeability and compaction models. The steady-state and advancing front permeability measurement methods are compared. The results indicate that both methods yield similar permeabilities for a plain weave, bi-axial fiberglass fabric. Also, a method to determine principal directions and permeabilities is discussed and results are shown for a multi-axial warp knit preform. The flow of resin through a blade-stiffened preform was modeled and experiments were completed to verify the results. The predicted inlet pressure was approximately 65% of the measured value. A parametric study was performed to explain differences in measured and predicted flow front advancement and inlet pressures. Furthermore, PR-500 epoxy resin/IM7 8HS carbon fabric flat panels were fabricated by the Resin Transfer Molding process. Tests were completed utilizing both perimeter injection and center-port injection as resin inlet boundary conditions. The mold was instrumented with FDEMS sensors, pressure transducers, and thermocouples to monitor the process conditions. Results include a comparison of predicted and measured inlet pressures and flow front position. For the perimeter injection case, the measured inlet pressure and flow front results compared well to the predicted results. The results of the center-port injection case showed that the predicted inlet pressure was approximately 50% of the measured inlet pressure. Also, measured flow front position data did not agree well with the predicted results. Possible reasons for error include fiber deformation at the resin inlet and a lag in FDEMS sensor wet-out due to low mold pressures.

Fingerson, John C.↗

NASA NTRS1991

A Review of Sodium-Metal Chloride Battery Activity At JPL

Following the disclosures by Coetzer et al. on the use of transition metal chlorides in chloroaluminates as alternate cathodes to sulfur in rechargeable sodium batteries, several laboratories, including the Jet Propulsion Laboratory, focused their attention on these systems. These systems have certain distinct advantages over sodium-sulfur batteries such as increased safety, inherent overcharge capability, and lower operating temperatures. Two systems, i.e., Na/FeCl2 and NaNiCl2, were developed extensively and evaluated in various applications including electric vehicles and space. Their performance has been very encouraging and warrants a detailed fundamental study on these cathodes. At the Jet Propulsion Laboratory a program was initiated two years back to understand the electrochemical behavior of FeCl2 and NiCl2, and to identify and evaluate other transition metal chlorides of promise. The initial efforts focused on the methods of fabrication of the electrodes and their electrochemical characterization. Subsequent studies were aimed at establishing the reaction mechanism, determining the kinetics, and identifying the rate-limiting processes in te reduction of metal chloride cathodes. Nickel chloride emerged form these studies as the most promising candidate material and was taken up for further detailed study on its passivation- a rate limiting process-under different experimental conditions. Also, the feasibility of using copper chloride, which is expected to have a higher energy density, has been assessed. On the basis of the criteria established from the voltammetric response of FeCl2, NiCl2, and CuCl2, several other transition metal chlorides were screened. Of these, molybdenum and cobalt appear promising.

Ratnakumar, B. V.↗

NASA NTRS1999

Abnormal norepinephrine clearance and adrenergic receptor sensitivity in idiopathic orthostatic intolerance

BACKGROUND: Chronic orthostatic intolerance (OI) is characterized by symptoms of inadequate cerebral perfusion with standing, in the absence of significant orthostatic hypotension. A heart rate increase of >/=30 bpm is typical. Possible underlying pathophysiologies include hypovolemia, partial dysautonomia, or a primary hyperadrenergic state. We tested the hypothesis that patients with OI have functional abnormalities in autonomic neurons regulating cardiovascular responses. METHODS AND RESULTS: Thirteen patients with chronic OI and 10 control subjects underwent a battery of autonomic tests. Systemic norepinephrine (NE) kinetics were determined with the patients supine and standing before and after tyramine administration. In addition, baroreflex sensitivity, hemodynamic responses to bolus injections of adrenergic agonists, and intrinsic heart rate were determined. Resting supine NE spillover and clearance were similar in both groups. With standing, patients had a greater decrease in NE clearance than control subjects (55+/-5% versus 30+/-7%, P<0.02). After tyramine, NE spillover did not change significantly in patients but increased 50+/-10% in control subjects (P<0.001). The dose of isoproterenol required to increase heart rate 25 bpm was lower in patients than in control subjects (0.5+/-0.05 versus 1.0+/-0.1 microg, P<0.005), and the dose of phenylephrine required to increase systolic blood pressure 25 mm Hg was lower in patients than control subjects (105+/-11 versus 210+/-12 microg, P<0.001). Baroreflex sensitivity was lower in patients (12+/-1 versus 18+/-2 ms/mm Hg, P<0.02), but the intrinsic heart rate was similar in both groups. CONCLUSIONS: The decreased NE clearance with standing, resistance to the NE-releasing effect of tyramine, and increased sensitivity to adrenergic agonists demonstrate dramatically disordered sympathetic cardiovascular regulation in patients with chronic OI.

Clinical Trial↗

DOE OSTI2025

Spatially Patterned Architectures to Modulate CO 2 Reduction Cascade Catalysis Kinetics

Electrochemical CO 2 reduction using renewable sources of electrical energy holds promise for converting CO 2 into fuels and chemicals. The complex interactions among chemical/electrochemical reactions and mass transport make it difficult to analyze the effect of an individual process on electrode performance based only on experimental methods. Here, we developed a generalized steady-state simulation to describe an electrode surface in which sequential cascade catalysts are patterned in a periodic trench design. If appropriately constructed, this trench geometry is hypothesized to be able to yield a higher net current density for a CO 2 reduction (CO 2 R) cascade reaction. We have used realistic experimental reaction kinetics to investigate the role of trench geometry in mass transport, local microenvironments, and selectivity for a model CO 2 R cascade reaction. The model considers local concentration gradients of bicarbonate species at quasi-equilibrium and catalytic surface reactions based on concentration-dependent Butler–Volmer kinetics. Our results suggest that varying the spatial distribution of active sites plays a significant role in facilitating effective mass transport between active sites, modulating selectivity for the cascade reaction, and enhancing the yield of desirable cascade products. Moreover, we observe that this trench geometry significantly alters the cascade reaction rate by affecting the local pH, which can cause inadvertent depletion of available aqueous CO 2 to limit the CO 2 R cascade kinetics and modest suppression of the hydrogen evolution reaction (HER). The results highlight the trade-offs between mass transport, pH, and reaction kinetics that become apparent only when considering the coupled physics of all processes at the electrode surface. Here, this model can thus serve as a primary tool to build more selective and efficient patterned architectures for the CO 2 R cascade catalysis.

CO2 reduction↗

DOE OSTI2025

Resolving SPARC–HSA binding kinetics with an ultrasensitive photonic sensor based on bound states in the continuum

Secreted protein acidic and rich in cysteine (SPARC) is critical in cell-matrix interactions and tissue remodeling. It influences tumor progression through its affinity for human serum albumin (HSA) - the most abundant plasma protein, which also plays a crucial role in drug delivery. Strong molecular binding leads to a dissociation constant KD in the nanomolar range. Thus, determining KD requires detecting sub-nanomolar concentrations with ultrasensitive methods. This may be crucial for elucidating the nature of SPARC-HSA binding, as their interaction remains a subject of debate. Capturing these interactions accurately requires a platform capable of resolving rapid binding kinetics at extremely low analyte concentrations. In this work, we report on a microfluidics-integrated photonic nanostructure that supports bound states in the continuum (BICs) and is optimized for studying the fast kinetics of high-affinity protein-protein interactions. The unprecedented capability of detecting sub-nanomolar concentrations allows quantifying KD between SPARC and HSA beyond the state of the art. We leverage an all-dielectric photonic crystal slab (PhCS) sustaining two BIC branches arising from gapped Dirac cone dispersion. HSA is covalently immobilized on the PhCS bonded to a PDMS microfluidic chamber. SPARC dissociation is carried out using PBS buffer (pH 7.4), ensuring complete protein release through precise control of the flow rate and continuous spectral monitoring of the BICs. The measured KD=8.2±0.8 nM confirms the strong affinity of SPARC for HSA. This study highlights the potential of BIC-based sensing as a versatile tool for investigating protein interactions. These results also have implications for the optimization of drug delivery systems and cancer treatment strategies.

Albumin↗

DOE OSTI2025

Scanning Electrochemical Microscopy for Kinetic Investigations in Viscous Deep Eutectic Solvents: Identifying Practical Approach Curves and Deviations from Electron Transfer Models

Determining heterogeneous electrochemical electron transfer (ET) kinetics in electrolytes with a wide range of physical properties is of great interest for achieving high-performance redox flow batteries. Among such electrolytes, concentrated hydrogen-bonded electrolytes (CoHBEs), including deep eutectic solvents (DESs), have recently garnered significant attention. Unfortunately, traditional Tafel analysis using macroelectrodes often encounters issues with mass transfer limitations in CoHBEs with high viscosities, thereby restricting kinetic analysis to a narrow potential window. Here, in this work, we introduce a methodology for evaluating ET kinetics in viscous DES using the scanning electrochemical microscopy (SECM). We first determined practical solutions to SECM tip positioning in ethaline DES, which yield pseudopositive feedback responses. Lattice Boltzmann method (LBM) simulations helped us rationalize the impact of the fluid and concentration fields, as well as tip geometry, tip approach velocity v, and the solvent viscosity ηs, on the shape of the approach curves. In addition to successfully recreating approach curves over a variety of conditions, we found that approaching a conductor ensured a practical point where the normalized tip response (Ni T = 2) converged at L = 0.7 within ∼10% error regardless of tip velocity. With positioning capabilities at hand, we investigated the kinetics of Fe 3+ /Fe 2+ redox couple in aqueous and the ethaline media. The experimental kinetic results were interpreted using the Butler–Volmer (BV) and Marcus–Hush–Chidsey (MHC) models. For ethaline, a nonideal kinetic behavior was observed, potentially attributed to solvent dynamics within DESs or to the interplay of chloride anions in the charge transfer process.

electrodes↗

NASA NTRSDate not supplied

Zircon (U-TH)/He Impact Crater Thermochronometry and the Effects of Shock Microstructures on Helium Diffusion Kinetics

Accurate age determinations of hyper-velocity impact and cratering events remains difficult and often controversial, while less than half of all known impact craters are regarded as accurately and precisely dated. Besides 40Ar/39Ar and U-Pb methods, zircon (U-Th)/He dating of impactites is a burgeoning technique to date large- to medium-sized impact structures. Zircon (U-Th)/He ages can be fully reset in minutes at 1000°C, T commonly reached in and directly adjacent to impact melt domains, whereas complete resetting of zircon (U-Th)/He at <300°C, which might be encountered near the crater margins or persist in post-impact hydrothermal systems, may take >103-4 years. However, there is a critical need to test the reliability of (U-Th)/He impact dating in shock deformed zircon, and to quantify helium diffusion kinetics in well-characterized grains with a broad spectrum of shock-induced defect substructures. For this purpose, we investigated samples from two impact structures, the 66 Ma Chicxulub multi-ring basin and the 15 Ma Ries complex crater, to compare zircon diffusion kinetics from impact structures with varying parameters, including size, age, and hydrothermal system longevity. Shock microstructures were characterized by backscattered-electron (BSE) imaging prior to determination of diffusion step-heating fractional release experiments using light-bulb furnace with prograde and retrograde incrementally 10°C steps from 300°C to 600°C. We find that zircon with low-level shock microstructures exhibit no significant deviation from helium diffusion kinetics of undamaged zircon. In contrast, zircon grains with planar deformation features and granular textures classified by SEM are characterized by a dramatic decrease in helium retentivity, similar to radiation damage, due to the reduction in the effective domain size and the introduction of fast diffusion pathways. This likely renders shocked grains more susceptible to impact-induced hydrothermal resetting. Hence, characterization of impact microstructure is critical for determining accurate impact ages, but also offers the opportunity to determine the magnitude and duration of post-impact hydrothermal circulation.

Catherine Ross↗

DOE OSTI2025

Antenna arrays for neutrino mass measurements with cyclotron radiation emission spectroscopy

Cyclotron Radiation Emission Spectroscopy (CRES) is a technique for precision measurements of kinetic energies of charged particles, pioneered by the Project 8 experiment to measure the neutrino mass using the tritium end-point method. It was recently employed for the first time to measure the molecular tritium spectrum and place a limit on the neutrino mass using a cubic-centimeter-scale detector. Future direct neutrino mass experiments are developing the technique to overcome the systematic and statistical limitations of current detectors. Here, this paper describes one such approach, namely the use of antenna arrays for CRES in free space. Phenomenology, detector design, simulation, and performance estimates are discussed, culminating with an example design with a projected sensitivity of 𝑚 𝛽 < ⁢0.04 eV/𝑐 2 . Prototype antenna array measurements are also shown for a demonstrator-scale setup as a benchmark for the simulation. By consolidating these results, this paper serves as a comprehensive reference for the development and performance of antenna arrays for CRES.

Physics - Nuclear physics and radiation physics↗

DOE OSTI2025

Data-Driven Closures and Assimilation for Stiff Multiscale Random Dynamics

Here, we introduce a data-driven and physics-informed framework for propagating uncertainty in stiff, multiscale random ordinary differential equations (RODEs) driven by correlated (colored) noise. Unlike systems subjected to Gaussian white noise, a deterministic equation for the joint probability density function (PDF) of RODE state variables does not exist in closed form. Moreover, such an equation would require as many phase-space variables as there are states in the RODE system. To alleviate this curse of dimensionality, we instead derive exact, albeit unclosed, reduced-order PDF (RoPDF) equations for low-dimensional observables/quantities of interest. The unclosed terms take the form of state-dependent conditional expectations, which are directly estimated from data at sparse observation times. However, for systems exhibiting stiff, multiscale dynamics, data sparsity introduces regression discrepancies that compound during RoPDF evolution. This is overcome by introducing a kinetic-like defect term to the RoPDF equation, which is learned by assimilating in sparse, low-fidelity RoPDF estimates. Two assimilation methods are considered, namely nudging and deep neural networks, which are successfully tested against Monte Carlo simulations.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Preliminary Assessment of Alternate Chlorination Process

Recent advancements towards low-temperature chlorination with disulfur dichloride and thionyl chloride of Al-clad used nuclear fuel (UNF) have been summarized for work control technical expertise development at the Savannah River National Laboratory (SRNL). This technique aims to provide a more effective method for separating U from cladding or alloying elements. A preliminary assessment determined needs for unit operation developments in regard to reaction kinetics and reagent quality. Furthermore, an analysis of an Uruguay fuel plate (U-Al x fuel meat), with low-enriched uranium (LEU) and located at SRNL, was a potential candidate for future experiments with lightly irradiated (0.08% burnup) fuel to test for chlorination. Future proposed work would involve kinetic studies, reagent quality assessments, and the machining of the fuel plate down to an appropriate bench-scale size and testing the effectiveness of low-temperature chlorination on the fuel plate.

Chlorination↗

NASA NTRS1980

Effect of off-design operation of MHD generators on NO/x/ chemical kinetics

The purpose of this study is to provide a capability for determining the chemical kinetic behavior of one family of pollutants, the nitrogen oxides, in the flow of a coal-fired MHD generator facility. The method used in the study allows the prediction of the nonequilibrium concentration of the minor NO(x) species in a flow otherwise assumed in equilibrium. Consideration is given to the effect of preheat, stoichiometry, and oxygen enrichment of the NO(x) concentration. The effect of preheat and stoichiometry is found to have a significant influence on the NO(x) concentration at the exit of the radiant boiler.

Simmons, G. A.↗