Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrode microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Two-layer cathode architecture for high-energy density and high-power density solid state batteries

Solid state batteries with high-energy density and high-power density require the development of thick and energy dense cathodes. Structured cathode electrodes with a double-layer configuration were enabled using a freeze tape casting technique. A bottom dense layer was utilized to enhance the energy density whereas a top porous layer with vertically aligned walls was utilized to enhance the power density. The porous structure of the power layer was achieved by ice templating this layer on top of the densified energy layer of the cathode. This configuration was found to better utilize the active material of the cathodes and was optimized using numerical simulation and computer modeling. Cells with Li metal anode and LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) at approximately 5 and 20 mg/cm 2 were cycled at 70 °C at different C-rates. Poly(ethylene oxide) (PEO) with lithium bis-trifluoromethanesulfonimide (LiTFSI) was used for the catholyte and the solid-state electrolyte. The structured cathodes exhibited more than double capacity values as well as better Coulombic efficiency compared to non-structured (single-layer) thick cathodes. In conclusion, synchrotron X-ray tomography and scanning electron microscopy were used to characterize the microstructure of the cathodes.

25 ENERGY STORAGE↗

Boosting the sodium storage behaviors of carbon materials in ether-based electrolyte through the artificial manipulation of microstructure

The porous carbon blacks rationally designed by a facile yet efficient NH 3 thermal etching route have been investigated as anode materials in an ether-based electrolyte for sodium-ion batteries. The as-synthesized CBN35 carbon black with a 35% weight loss after NH3 thermal etching exhibited a large specific charge capacity of 352 mAh g -1 at 50 mA g -1 and a superior rate capability of 101 mAh g -1 at 16000 mA g -1 , due to its highest microporosity, an appropriate surface area, a desirable microstructure, and a promising hybrid intercalation mechanism. Impressively, even cycled at 1600 mA g -1 over 3200 cycles, an outstanding reversible capacity of 103 mAh g -1 with a negligible 0.0162% capacity loss per cycle can still be achieved. Based on the multimodal characterizations including the structural probes of phase evolution for carbon materials, the electrochemical techniques, and the surface-sensitive XAS measurements, the exceptional electrochemical properties should stem from several merits of modified carbon black system. While the particular microporous structure provides relatively more accessible sodium storage sites, a novel hybrid intercalation mechanism in ether-based electrolyte would incorporate the sodium ion insertion into the disordered structure with the solvated sodium ion species co-intercalation into the graphitic phase. In addition to the diffusion-controlled redox reactions, the noticeable surface-induced pseudocapacitive reactions also significantly contribute to the charge storage upon sodiation and guarantee the rapid migrations of sodium ions/solvated compounds. In conclusion, this system further features a controlled emergence of a robust but thin solid electrolyte interphase layer, which could suppress the side reactions of active electrode with reactive electrolyte, maintain the fragile porous structure upon cycling, and facilitate the migrations of sodium ions and solvated sodium ion compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ce- and Ni-Codoped Double PrBaMn 2 O 5 Perovskite as a Ceramic SOFC Anode

This study explores the efficacy of cerium introduction, both on its own and in combination with nickel, into PrBaMn 2 O 5+δ (PBM) structures to enhance solid oxide fuel cell (SOFC) anodes. We synthesized Pr 1–x Ce x BaMn 2 O 5+δ compositions for x values of 0.05 (PrCe5) and 0.1 (PrCe10), as well as a nickel-doped variant (PrCe5Ni), assessing their performance under H 2 – 3% H 2 O reducing conditions pertinent to SOFC anode operations. Our findings reveal that the PrCe5 composition exhibits a thermal expansion coefficient (TEC) that not only improves upon that of the Ce-free counterpart but also aligns closely with the TEC standards of prevalent SOFC electrolytes. A notable advancement was achieved with the application of a 3.5 μm gadoliniadoped ceria (GDC) buffer layer through physical vapor deposition, effectively mitigating chemical interactions between PBM-based anodes and yttria-stabilized zirconia (YSZ) electrolytes, a concern highlighted by in situ neutron diffraction analyses. Electrochemical impedance spectroscopy, conducted over 220 h in a H 2 –3% H 2 O atmosphere at 750 °C, demonstrated that the optimal 3.5 μm thickness of the GDC buffer layer significantly minimizes the area-specific resistance (ASR) degradation rate to 0.002 Ω cm 2 /h, markedly outperforming both thinner (1 μm) and thicker (8 μm) GDC layers, which showed higher degradation rates of 0.15–0.2 Ω cm 2 /h due to the diffusion of Ba ions or delamination. Moreover, cerium doping fosters superior microstructural stability and obviates barium diffusion, thereby suggesting an enhanced durability of the doped anodes over their lifespan. Integrating nickel into the PrCe5 structure halved the ASR to 0.5 Ω cm 2 at 750 °C, situating it well within the ideal performance range for SOFC anodes. Furthermore, the enhancement brought about by simultaneously doping PBM with cerium and nickel, which fundamentally relies on the critical contributions of defect chemistry and crystal structure, highlights the significance of these fields in creating sophisticated materials for energy related applications.

25 ENERGY STORAGE↗

Robust Interfacial Effect in Multi-interface Environment through Hybrid Reconstruction Chemistry for Enhanced Energy Storage

Electrochemical-oxidation-driven reconstruction has emerged as an efficient approach for developing advanced materials, but the reconstructed microstructure still faces challenges including inferior conductivity, unsatisfying intrinsic activity, and active-species dissolution. In this report we present hybrid reconstruction chemistry that synergistically couples electrochemical oxidation with electrochemical polymerization (EOEP) to overcome these constraints. During the EOEP process, the metal hydroxides undergo rapid reconstruction and dynamically couple with polypyrrole (PPy), resulting in an interface-enriched microenvironment. We observe that the interaction between PPy and the reconstructed metal center (i.e., Mn > Ni, Co) is strongly correlated. Theoretical calculation results demonstrate that the strong interaction between Mn sites and PPy breaks the intrinsic limitation of MnO 2 , rendering MnO 2 with a metallic property for fast charge transfer and enhancing the ion-adsorption dynamics. Operando Raman measurement confirms the promise of EOEP-treated Mn(OH) 2 (E-MO/PPy) to stably work under a 1.2 V potential window. The tailored E-MO/PPy exhibits a high capacitance of 296 F g –1 at a large current density of 100 A g –1 . Here our strategy presents breakthroughs in upgrading the electrochemical reconstruction technique, which enables both activity and kinetics engineering of electrode materials for better performance in energy-related fields.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Graphene Oxide Interlayers for Robust, High-Efficiency Organic Photovoltaics

Organic photovoltaic (OPV) materials have recently garnered significant attention as enablers of high power conversion efficiency (PCE), low-cost, mechanically flexible solar cells. Nevertheless, further understanding-based materials developments will be required to achieve full commercial viability. In particular, the performance and durability of many current generation OPVs are limited by poorly understood interfacial phenomena. Careful analysis of typical OPV architectures reveals that the standard electron-blocking layer, poly-3,4-ethylenedioxy-thiophene:poly(styrene sulfonate) (PEDOT:PSS), is likely a major factor limiting the device durability and possibly performance. Here we report that a single layer of electronically tuned graphene oxide is an effective replacement for PEDOT:PSS and that it significantly enhances device durability while concurrently templating a performance-optimal active layer {pi}-stacked face-on microstructure. Such OPVs based on graphene oxide exhibit PCEs as high as 7.5% while providing a 5x enhancement in thermal aging lifetime and a 20x enhancement in humid ambient lifetime versus analogous PEDOT:PSS-based devices.

14 SOLAR ENERGY↗

ED-cPSD: Fast Phase-Size Distribution via Sequential Erosion-Dilation

The Erosion-Dilation continuous Phase-Size Distribution, ED-cPSD, is an application for calculating continuous pore and particle-size distribution from digital reconstructions and/or image-based structural data. It is based on the erosion-dilation continuous phase-size distribution method. A continuous size distribution is a measure of the probability density of finding a particle or pore of a certain size. These distributions are of interest in any field of study involving porous media, including but not limited to electrochemistry, petroleum engineering, geology, and food science. The algorithm behind the software provides a computationally efficient way to calculate phase-size distributions for large domains. For a 3D battery electrode reconstruction with 1.3 x 10 8 voxels, the particle size distribution is derived in under 2 min on a desktop, while also retaining flexibility and computational efficiency for HPC-scale multi-threading. The software can handle structures with over 10 9 voxels. The algorithm is roughly 280 times faster than a previous version on the same task.

Characterization↗

Neural Network Enhanced RKPM for Electrochemical-Mechanical Coupled Damage Modeling of Energy Storage Materials

Energy storage materials undergo significant charge cycling, which makes understanding their reliability and durability fundamental in predicting performance and service life. Strong electrochemical-mechanical coupling and highly anisotropic material properties contribute to the formation and propagation of micro-cracking, largely along material interfaces and grain boundaries. For Li-ion batteries, for example, lithium moving between electrodes during charging and discharging process causes expansion and contraction of grains, and the strongly anisotropic and nonlinearly [Li]-dependent grain material properties can cause grains to expand into and contract away from each other, leading to chemo-mechanical cracking. In the first part of this work, a RKPM based computational framework for solving the coupled solid-phase lithium conservation with Fickian diffusion and the lithium concentration dependent anisotropic mechanical problem subjected to a highly nonlinear Butler-Volmer boundary condition is introduced. The choice of RKPM completeness conditions for lithium concentration and mechanical deformation fields, and the variational consistency condition for the domain integration of the coupled problem is first determined. In the second part of this work, a neural network-enhanced reproducing kernel particle method (NN-RKPM) [1] is leveraged to accurately capture damage and crack propagation throughout the material, by learning the location, orientation, and sharpness of discontinuity while allowing for a coarser nodal distribution than that is necessary for capturing sharp solution transitions using traditional mesh-based methods. NN-RKPM is used to inform how crack opening and closure in turn affect the coupled chemical equations and material microstructure.

damage modeling↗

Nano-structural Characteristics of N-doped ZnO Thin Films and Fabrication of Film Bulk Acoustic Resonator Devices

N-doped ZnO thin films (ZnO:N) with c-axis preferred orientation were prepared on p-Si(100) wafers, using an RF magnetron sputter deposition. For ZnO deposition, N{sub 2}O gas was employed as a dopant source and various deposition conditions such as N{sub 2}O gas fraction and RF power were applied. In addition, the film bulk acoustic resonator (FBAR) devices with three kinds of top electrodes patterns were fabricated by using the N-doped ZnO thin films as the piezoelectric layers. The depth profiles of the nitrogen [N] atoms incorporated into the ZnO thin films were investigated by an Auger Electron Spectroscopy (AES) and the nano-scale structural characteristics of the N-doped ZnO (ZnO:N) thin films were also investigated by a scanning electron microscope (SEM) technique. The fabricated resonators were evaluated by measuring the return loss (S{sub 11}) characteristics using a probe station and E8361A PNA Network Analyzer.

36 MATERIALS SCIENCE↗

Toward Optimizing Electrospun Nanofiber Fuel Cell Catalyst Layers: Polymer–Particle Interactions and Spinnability

We investigate the effect of the poly(acrylic acid) (PAA) carrier polymer concentration on the microstructure and rheological properties of catalyst inks for electrospun polymer–electrolyte membrane fuel-cell catalyst layers. Characterization of an ink microstructure using oscillatory shear rheology showed that the catalyst particles (platinum on carbon) are significantly agglomerated in the absence of PAA or an ionomer. Both the ionomer and PAA promoted the stability of the particles against agglomeration via electrosteric stabilization by adsorbing onto the particle surface. Increasing the PAA concentration increased the stability of the particles (or reduced the agglomerated structure) due to increasing PAA coverage onto the free surface area of the particles. However, beyond a certain increase in concentration, PAA was found to predominantly remain as an excess free polymer in the ink due to an insufficient free/available surface area on the particles for further PAA coverage. Extensional rheology measurements demonstrated that PAA enhances the extensional viscosities of the inks. Consequently, increasing the PAA concentration in the ink promoted the evolution of uniform nanofibers. However, beyond a certain concentration, a significant increase in the shear viscosities of the inks led to defective fiber morphologies because of the onset of flow instabilities. Electrochemical performance comparisons between catalyst layers with different PAA concentrations showed maximum performance at the PAA concentration that led to the least agglomerated structure of the catalyst, most uniform fiber morphologies, and low concentrations of free (non-adsorbing) PAA in the electrode. These results provide a rationale for optimization of electrospun catalyst nanofibers for both spinnability and electrochemical performance.

25 ENERGY STORAGE↗

Synthesis of Ti-based electrodes using Ti-salt flocculated sludge and their application in lithium-ion batteries

We report a simple strategy to synthesize the nanostructured TiO{sub 2} samples by a solid state reaction using Ti-salt flocculated sludge. The structure and morphology of the Ti-salt flocculated sludge, nanostructured TiO{sub 2} samples and pure commercial Aldrich TiO{sub 2} powder were characterized by powder X-ray diffraction and field emission scanning electron microscopy (FE-SEM). The electrochemical performances were evaluated in coin type cells. Nanostructured TiO{sub 2} samples, obtained by Ti-salt flocculated sludge shows a higher capacity and better cycling performances than pure commercial Aldrich TiO{sub 2} powder at the cutoff of 1.0–2.5 V especially at high current rate. The enhanced cycling performance can be attributed to the facts that their high crystallinity and uniform nano-sized distribution.

36 MATERIALS SCIENCE↗

Impact of Stabilizing Cations on Lithium Intercalation in Tunneled Manganese Oxide Cathodes

Stabilizing cations such as K + , Ba 2+ , and Ag + are known to provide charge neutrality and enhance structural stability in low-cost tunneled manganese dioxide (MnO 2 ) cathodes for Li ion batteries. However, a fundamental understanding of the role of these cations in the electrochemical performance of tunneled MnO 2 cathodes remains unclear, especially at low stabilizing cation concentrations. Here, we employ density functional theory (DFT + U) calculations to reveal the impact of stabilizing potassium cation (K + ) concentration on the structural stability, electronic properties, and kinetics of lithium transport in 2 x 2 tunneled manganese oxide (α-K y Mn 8 O 16 , at y = 0, 1, and 2) battery cathodes during lithium intercalation. Specifically, we provide insights into the effect of K + ions on several critical factors governing the electrochemical storage performance of tunneled MnO2 cathodes, including (a) energetically favorable Li+ host sites, (ii) Li + and electron transport capabilities, (iii) optimal intercalation pathways, crystal distortion, microstructural stability, and tunneled-to-layer phase transformation as a function of lithium content, and (iv) cell output voltage profile. Interestingly, we find that low K + concentrations (y ≤ 1) yield partially cation-deficient tunnels in the MnO 2 cathode. Such unique tunnel structures in the cathode enable (a) low kinetic barriers for Li transport, (b) excellent thermodynamic stability of the tunneled structure even at a high Li + loading (up to ~ 0.625 Li/Mn), and (c) good electronic conductivity facilitated by Jahn-Teller distortions; all of which are critical for achieving high capacity batteries with enhanced rate capability. Additionally, these results provide perspectives to design low-cost transition metal oxide cathodes for high-performance Li-ion batteries with excellent cycle life.

25 ENERGY STORAGE↗

Evaluating the Rheo-electric Performance of Aqueous Suspensions of Oxidized Carbon Black

Here, the macroscopic properties of carbon black suspensions are primarily determined by the agglomerate microstructure built of primary aggregates. Conferring colloidal stability in aqueous carbon black suspensions should thus have a drastic impact on their viscosity and conductivity. Carbon black was treated with strong acids following a wet oxidation procedure. An analysis of the resulting particle surface chemistry and electrophoretic mobility was performed in evaluating colloidal stability. Changes in suspension microstructure due to oxidation were observed using small-angle X-ray scattering. Utilizing rheo-electric measurements, the evolution of the viscosity and conductivity of the carbon black suspensions as a function of shear rate and carbon content was thoroughly studied. The carboxyl groups installed on the carbon black surface through oxidation increased the surface charge density and enhanced repulsive interactions. Electrostatic stability inhibited the formation of the large-scale agglomerates in favor of the stable primary aggregates in suspension. While shear thinning, suspension conductivities were found to be weakly dependent on the shear intensity regardless of the carbon content. Most importantly, aqueous carbon black suspensions formulated from electrostatically repulsive primary aggregates displayed a smaller rise in conductivity with carbon content compared to those formulated from attractive agglomerates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructure and corrosion resistance of nanocrystalline TiZrN films on AISI 304 stainless steel substrate

This study investigated the microstructure and properties of nanocrystalline TiZrN films on AISI 304 stainless steel substrate. TiZrN films were prepared by reactive magnetron sputtering based on the previous optimum coating conditions (substrate temperature, system pressure, nitrogen flow, etc.) for TiN and ZrN thin films. The composition ratio of TiZrN coatings were adjusted by changing the Zr target power, while keeping the Ti target power constant. Experiments were conduced to find the optimum composition with desired properties. The ratio of TiZrN composition was analyzed by x-ray photoelectron spectroscopy and Rutherford backscattering spectrometer. In terms of phase formation, there were two types of coatings that were considered: single-phase solid solutions of TiZrN and interlacing nuclei of TiZr in the matrix of TiZrN. The thickness of all TiZrN films as measured by the secondary ion mass spectroscopy was about 500 nm, and the composition depth profiles indicated that the compositions in the TiZrN films were uniform from the film surface to the 304 stainless steel substrate. The crystal structure of the TiZrN films was determined by x-ray diffraction using a M18XHF-SRA diffractometer with Cu K{sub {alpha}} radiation. A diffraction peak of TiZrN (002) was observed between that of TiN (002) and ZrN (002); similarly, a diffraction peak of TiZrN (111) was observed between that of TiN(111) and ZrN(111), respectively. The corrosion resistance of the TiZrN film deposited on the 304 stainless steel has been investigated by electrochemical measurement. The electrolyte, 0.5M H{sub 2}SO{sub 4} containing 0.05M KSCN, was used for the potentiodynamic polarization. The potentiodynamic scan was conducted from -800 to 800 mV standard calomel electrode (SCE).

36 MATERIALS SCIENCE↗

A High Temperature Electrochemical Energy Storage System Based on Sodium Beta-Alumina Solid Electrolyte (Base)

This report summarizes the work done during the period September 1, 2005 and March 31, 2008. Work was conducted in the following areas: (1) Fabrication of sodium beta{double_prime} alumina solid electrolyte (BASE) using a vapor phase process. (2) Mechanistic studies on the conversion of {alpha}-alumina + zirconia into beta{double_prime}-alumina + zirconia by the vapor phase process. (3) Characterization of BASE by X-ray diffraction, SEM, and conductivity measurements. (4) Design, construction and electrochemical testing of a symmetric cell containing BASE as the electrolyte and NaCl + ZnCl{sub 2} as the electrodes. (5) Design, construction, and electrochemical evaluation of Na/BASE/ZnCl{sub 2} electrochemical cells. (6) Stability studies in ZnCl{sub 2}, SnCl{sub 2}, and SnI{sub 4} (7) Design, assembly and testing of planar stacks. (8) Investigation of the effect of porous surface layers on BASE on cell resistance. The conventional process for the fabrication of sodium ion conducting beta{double_prime}-alumina involves calcination of {alpha}-alumina + Na{sub 2}CO{sub 3} + LiNO{sub 3} at 1250 C, followed by sintering powder compacts in sealed containers (platinum or MgO) at {approx}1600 C. The novel vapor phase process involves first sintering a mixture of {alpha}-alumina + yttria-stabilized zirconia (YSZ) into a dense ceramic followed by exposure to soda vapor at {approx}1450 C to convert {alpha}-alumina into beta{double_prime}-alumina. The vapor phase process leads to a high strength BASE, which is also resistant to moisture attack, unlike BASE made by the conventional process. The PI is the lead inventor of the process. Discs and tubes of BASE were fabricated in the present work. In the conventional process, sintering of BASE is accomplished by a transient liquid phase mechanism wherein the liquid phase contains NaAlO{sub 2}. Some NaAlO{sub 2} continues to remain at grain boundaries; and is the root cause of its water sensitivity. In the vapor phase process, NaAlO{sub 2} is never formed. Conversion occurs by a coupled transport of Na{sup +} through BASE formed and of O{sup 2-} through YSZ to the reaction front. Transport to the reaction front is described in terms of a chemical diffusion coefficient of Na{sub 2}O. The conversion kinetics as a function of microstructure is under investigation. The mechanism of conversion is described in this report. A number of discs and tubes of BASE have been fabricated by the vapor phase process. The material was investigated by X-ray diffraction (XRD), optical microscopy and scanning electron microscopy (SEM), before and after conversion. Conductivity (which is almost exclusively due to sodium ion transport at the temperatures of interest) was measured. Conductivity was measured using sodium-sodium tests as well as by impedance spectroscopy. Various types of both planar and tubular electrochemical cells were assembled and tested. In some cases the objective was to determine if there was any interaction between the salt and BASE. The interaction of interest was mainly ion exchange (possible replacement of sodium ion by the salt cation). It was noted that Zn{sup 2+} did not replace Na+ over the conditions of interest. For this reason much of the work was conducted with ZnCl{sub 2} as the cathode salt. In the case of Sn-based, Sn{sup 2+} did ion exchange, but Sn{sup 4+} did not. This suggests that Sn{sup 4+} salts are viable candidates. These results and implications are discussed in the report. Cells made with Na as the anode and ZnCl{sub 2} as the cathode were successfully charged/discharged numerous times. The key advantages of the batteries under investigation here over the Na-S batteries are: (1) Steel wool can be used in the cathode compartment unlike Na-S batteries which require expensive graphite. (2) Planar cells can be constructed in addition to tubular, allowing for greater design flexibility and integration with other devices such as planar SOFC. (3) Comparable or higher open circuit voltage (OCV) than the Na-S battery. (4) Wider operating temperature range and higher temperature operation than the Na-S battery. (5) If a cell fails, it fails in the short circuit mode unlike Na-S batteries. Also, cells were successfully subjected to several freeze-thaw cycles. Finally, the feasibility of assembling a planar stack was explored. A two cell stack was assembled and tested. A five cell stack was assembled.

25 ENERGY STORAGE↗

Robust dynamic operation of high temperature electrolysis solid oxide cells

Here, this study evaluates the durability of Ni/YSZ-supported SOECs under dynamic operating conditions relevant to real-world applications. Systematic tests were conducted to assess cell performance under steam cycling (3 to 75% humidified H 2 ), mode cycling between SOFC and SOEC operation, thermal cycling (150 to 750 °C at OCV, and 600 to 800 °C at 1.3V), and redox cycling (between 50% humidified H 2 and 50% humidified N 2 ). Steam cycling, mode cycling, and thermal cycling at OCV do not significantly accelerate performance degradation. Thermal cycling at 1.3V caused minimal damage within 600 to 800 °C. Full redox cycling (multi-hour oxidation holds) induced cell structural failure, while partial redox cycling (0.5 h holds) was tolerated. Extensive characterization revealed some material evolution, namely Sr and Co secondary phase formation, within the oxygen electrode due to La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ instability, especially for steam cycling and mode cycling. Minimal changes were identified within the Ni-YSZ fuel electrodes. These findings provide critical insights into SOEC reliability under dynamic conditions, supporting their application in dynamic or intermittent energy systems.

08 HYDROGEN↗

Combining phase-field crystal methods with a Cahn-Hilliard model for binary alloys

Diffusion-induced phase transitions typically change the lattice symmetry of the host material. In battery electrodes, for example, Li ions (diffusing species) are inserted between layers in a crystalline electrode material (host). This diffusion induces lattice distortions and defect formations in the electrode. The structural changes to the lattice symmetry affect the host material’s properties. We propose a 2D theoretical framework that couples a Cahn-Hilliard (CH) model, which describes the composition field of a diffusing species, with a phase-field crystal (PFC) model, which describes the host-material lattice symmetry. We couple the two continuum models via coordinate transformation coefficients. We introduce the transformation coefficients in the PFC method to describe affine lattice deformations. These transformation coefficients are modeled as functions of the composition field. Using this coupled approach, we explore the effects of coarse-grained lattice symmetry and distortions on a diffusion-induced phase transition process. In this paper, we demonstrate the working of the CH-PFC model through three representative examples: First, we describe base cases with hexagonal and square symmetries for two composition fields. Next, we illustrate how the CH-PFC method interpolates lattice symmetry across a diffuse phase boundary. Finally, we compute a Cahn-Hilliard type of diffusion and model the accompanying changes to lattice symmetry during a phase transition process.

25 ENERGY STORAGE↗

Development of a scalable, robust electrocatalytic technology for conversion of CO 2 to formic acid via microstructured materials

This project was funded by the Bioenergy Engineering for Product Synthesis (BEEPS) program under the Funding Opportunity Announcement (FOA) DE-FOA-0001916 Topic Area 5 “Rewiring Carbon Utilization”. This FOA sought projects that would electrocatalytically reduce CO 2 to a carbon intermediate and then upconvert to a multi-carbon product or fuel via non-photosynthetic biological system engineering. The project sought to combine the expertise of OCO Chem, whose chief scientist had previously developed an efficient electrocatalytic reactor for conversion of CO 2 to formate with potential to scale, Montana State University investigators who had recently patented a method for laterally grading membranes with the potential of improving reactant distribution and more uniform efficiency across membrane-based reactors, and University of South Florida which had recently discovered a novel C-C bond forming reaction not known to naturally occur in biological systems and which uses C1 substrates and circumvents the central microbial metabolism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗