Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computer software and hardware”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

MBSE Validation and Verification: Case Study for LADEE

The Lunar Atmosphere Dust Environment Explorer (LADEE) mission orbited the moon in order to measure the density, composition, and time variability of the lunar dust environment. The successful mission launched September 7, 2013 and was de-orbited and impacted the moon's surface on April 17, 2014. The ground-side and onboard flight software for the mission was developed using a “Model-Based Software Engineering” (MBSE) methodology combined with strong reuse of Government and Commercial Off-The Shelf (G/COTS) components. Models of the spacecraft and flight software were developed in a graphical dynamics modeling package. Flight Software requirements were prototyped and refined using the simulated models. After the model was shown to work as desired in the simulation framework, C-code software was automatically generated from the models. The auto-generated software was then tested in real-time Processor-in-the-Loop and Hardware-in-the-Loop test beds. “Traveling Road Show” test beds were used for early integration tests with payloads and other subsystems. Traditional techniques for verifying computational sciences models were used to characterize the spacecraft simulation. A lightweight set of formal methods analysis, static analysis, formal inspection, and code coverage analyses were utilized to further reduce defects in the onboard flight software artifacts. These techniques were applied early and often in the development process, iteratively increasing the capabilities of software and fidelity of vehicle models and test beds.

Model-Based Software Engineering, Validation and V↗

An innovative design for autonomous backup attitude control of the Gamma Ray Observatory

The Gamma Ray Observatory is a NASA funded three-axis stabilized spacecraft which will carry four scientific instruments to observe gamma ray phenomena. The requirement to protect the scientific mission from system failures led to the attitude control and determination system design described in this paper. The design employs nine control modes with error detection, hardware substitution, and autonomous mode switching. The system architecture evolved to eliminate cross-dependence between the primary on-board computer (OBC) and the backup control processor electronics. Cross strapping of sensors and actuators and separation of the input/output electronics ensure that a reliable set of sensors and actuators will be available for backup mode operation. The OBC software includes failure detection, hardware reconfiguration, and mode switching logic which provide the ability to autonomously transfer, upon anomaly, to a reliable backup mode. Verification of this mode transition design is done in four test programs: at the unit level, by analytical simulation, by a hybrid breadboard electronics-simulation setup, and by a flight hardware-simulation test.

Tai, F.↗

Cooperative GN&C development in a rapid prototyping environment

The Navigation, Control and Aeronautics Division (NCAD) at NASA-JSC is exploring ways of producing Guidance, Navigation and Control (GN&C) flight software faster, better, and cheaper. To achieve these goals NCAD established two hardware/software facilities that take an avionics design project from initial inception through high fidelity real-time hardware-in-the-loop testing. Commercially available software products are used to develop the GN&C algorithms in block diagram form and then automatically generate source code from these diagrams. A high fidelity real-time hardware-in-the-loop laboratory provides users with the capability to analyze mass memory usage within the targeted flight computer, verify hardware interfaces, conduct system level verification, performance, acceptance testing, as well as mission verification using reconfigurable and mission unique data. To evaluate these concepts and tools, NCAD embarked on a project to build a real-time 6 DOF simulation of the Soyuz Assured Crew Return Vehicle flight software. To date, a productivity increase of 185 percent has been seen over traditional NASA methods for developing flight software.

Bordano, Aldo↗

Investigations of rhesus monkey video-task performance: evidence for enrichment

We have developed the Language Research Center's Computerized Test System (LRC-CTS) for psychological research. Basically, the LRC-CTS is a battery of software tasks--computerized versions of many of the classic testing paradigms of cognitive and comparative psychology--and the hardware required to administer them. An XT- or 386-compatible computer is connected to a color monitor, onto which computer-generated stimuli are presented. Sound feedback is delivered through an external speaker/amplifier, and a joystick is used as an input device. The animals reach through the mesh of their home cages to manipulate the joystick, which causes isomorphic movements of a cursor on the screen thereby allowing animals to respond according to the varied demands of the tasks. Correct responses are rewarded with a fruit-flavored chow pellet. Using this technology, we have trained and tested rhesus monkeys, a variety of apes, human adults, and normally developing or mentally retarded human children. Other labs using the LRC-CTS are beginning to report encouraging results with other monkey species as well. From this research, a number of interesting and important psychological findings have resulted. In the present paper, however, evidence will be reviewed which suggests that the LRC-CTS is an effective means of providing environmental enrichment to singly housed rhesus monkeys.

Non-NASA Center↗

Vision Based Autonomous Robotic Control for Advanced Inspection and Repair

The advanced inspection system is an autonomous control and analysis system that improves the inspection and remediation operations for ground and surface systems. It uses optical imaging technology with intelligent computer vision algorithms to analyze physical features of the real-world environment to make decisions and learn from experience. The advanced inspection system plans to control a robotic manipulator arm, an unmanned ground vehicle and cameras remotely, automatically and autonomously. There are many computer vision, image processing and machine learning techniques available as open source for using vision as a sensory feedback in decision-making and autonomous robotic movement. My responsibilities for the advanced inspection system are to create a software architecture that integrates and provides a framework for all the different subsystem components; identify open-source algorithms and techniques; and integrate robot hardware.

sensory feedback↗

Applications Development for a Parallel COTS Spaceborne Computer

This presentation reviews the Remote Exploration and Experimentation Project (REE) program for utilization of scalable supercomputing technology in space. The implementation of REE will be the use of COTS hardware and software to the maximum extent possible, keeping overhead low. Since COTS systems will be used, with little or no special modification, there will be significant cost reduction.

Katz, Daniel S.↗

Off-line data analysis and data reduction from digitally controlled random test systems.

This paper discusses the merits of employing the new computer-controlled random environment control systems for fast and efficient large-scale data analysis when they are not being used for test control. Hardware and software requirements are stated. Several of the more familiar frequency functions are defined from the Fourier coefficients, the main product of the Fourier processors used in these control systems. Another function, the probability density function, is defined and suggestions for its application are made. An analysis example is presented. Some programming tips are listed, and the accuracy and reliability of frequency analysis measurements are considered.

Chapman, C. P.↗

Design requirements for SRB production control system. Volume 1: Study background and overview

The solid rocket boosters assembly environment is described in terms of the contraints it places upon an automated production control system. The business system generated for the SRB assembly and the computer system which meets the business system requirements are described. The selection software process and modifications required to the recommended software are addressed as well as the hardware and configuration requirements necessary to support the system.

Source record↗

User's guide to noise data acquisition and analysis programs for HP9845: Nicolet analyzers

A software interface package was written for use with a desktop computer and two models of single channel Fast Fourier analyzers. This software features a portable measurement and analysis system with several options. Two types of interface hardware can alternately be used in conjunction with the software. Either an IEEE-488 Bus interface or a 16-bit parallel system may be used. Two types of storage medium, either tape cartridge or floppy disc can be used with the software. Five types of data may be stored, plotted, and/or printed. The data types include time histories, narrow band power spectra, and narrow band, one-third octave band, or octave band sound pressure level. The data acquisition programming includes a front panel remote control option for the FFT analyzers. Data analysis options include choice of line type and pen color for plotting.

Mcgary, M. C.↗

Coherent integration

Coherent integration which is a digital filtering process and was applied to MST radar observations is discussed. It is simple to implement with either hardware or software and is appropriate for the very narrow band signals usually received by MST radars. By filtering the signal before performing spectral processing, the computations required for FFT or similar analysis are greatly reduced. Coherent integration does not increase the signal-to-noise ratio per unit bandwidth in the signal band. It filters out much of the wideband noise, which could also be done by full FFT processing of the raw signal.

Farley, D. T.↗

Avoiding pitfalls in simulating real-time computer systems

The software simulation of a computer target system on a computer host system, known as an interpretive computer simulator (ICS), functionally models and implements the action of the target hardware. For an ICS to function as efficiently as possible and to avoid certain pitfalls in designing an ICS, it is important that the details of the hardware architectural design of both the target and the host computers be known. This paper discusses both host selection considerations and ICS design features that, without proper consideration, could make the resulting ICS too slow to use or too costly to maintain and expand.

Smith, R. S.↗

Graphics mini manual

The computer graphics capabilities available at the Center are introduced and their use is explained. More specifically, the manual identifies and describes the various graphics software and hardware components, details the interfaces between these components, and provides information concerning the use of these components at LaRC.

Taylor, Nancy L.↗

High performance real-time flight simulation at NASA Langley

In order to meet the stringent time-critical requirements for real-time man-in-the-loop flight simulation, computer processing operations must be deterministic and be completed in as short a time as possible. This includes simulation mathematical model computational and data input/output to the simulators. In 1986, in response to increased demands for flight simulation performance, personnel at NASA's Langley Research Center (LaRC), working with the contractor, developed extensions to a standard input/output system to provide for high bandwidth, low latency data acquisition and distribution. The Computer Automated Measurement and Control technology (IEEE standard 595) was extended to meet the performance requirements for real-time simulation. This technology extension increased the effective bandwidth by a factor of ten and increased the performance of modules necessary for simulator communications. This technology is being used by more than 80 leading technological developers in the United States, Canada, and Europe. Included among the commercial applications of this technology are nuclear process control, power grid analysis, process monitoring, real-time simulation, and radar data acquisition. Personnel at LaRC have completed the development of the use of supercomputers for simulation mathematical model computational to support real-time flight simulation. This includes the development of a real-time operating system and the development of specialized software and hardware for the CAMAC simulator network. This work, coupled with the use of an open systems software architecture, has advanced the state of the art in real time flight simulation. The data acquisition technology innovation and experience with recent developments in this technology are described.

Cleveland, Jeff I., II↗

Searching for Organics, Fossils, and Biology on Mars

One of the goals of Astrobiology is to understand life on a fundamental level. All life on Earth is constructed from the same basic biochemical building blocks consisting of 20 amino acids with left handed symmetry, five nucleotides, a few sugars of right handed symmetry and some lipids. Using the metaphor of computers this is equivalent to saying that all life shares the same hardware. Beyond hardware similarity, it is now known that all life has fundamentally the same software. The genetic code of life is common to all organisms. Some have argued that the "hammer of evolution is heavy" and life anywhere is likely to be composed of identical biochemical and genetic patterns. However, in a system as complex as biochemistry it is likely that there are numerous local optima and the details of the optimum found by evolutionary selection on another world would likely depend on the initial conditions and random developments in the early biological history on that world. To address these fundamental questions in Astrobiology we need a second example of life: a second genesis.

McKay, Christopher P.↗

Standard Spacecraft Interfaces and IP Network Architectures: Prototyping Activities at the GSFC

Advancements in fright semiconductor technology have opened the door for IP-based networking in spacecraft architectures. The GSFC believes the same signlJicant cost savings gained using MIL-STD-1553/1773 as a standard low rate interface for spacecraft busses cun be realized for highspeed network interfaces. To that end, GSFC is developing hardware and software to support a seamless, space mission IP network based on Ethernet and MIL-STD-1553. The Ethernet network shall connect all fright computers and communications systems using interface standards defined by the CCSDS Standard Onboard InterFace (SOIF) Panel. This paper shall discuss the prototyping effort underway at GSFC and expected results.

Schnurr, Richard↗

Method of Real-Time Principal-Component Analysis

Dominant-element-based gradient descent and dynamic initial learning rate (DOGEDYN) is a method of sequential principal-component analysis (PCA) that is well suited for such applications as data compression and extraction of features from sets of data. In comparison with a prior method of gradient-descent-based sequential PCA, this method offers a greater rate of learning convergence. Like the prior method, DOGEDYN can be implemented in software. However, the main advantage of DOGEDYN over the prior method lies in the facts that it requires less computation and can be implemented in simpler hardware. It should be possible to implement DOGEDYN in compact, low-power, very-large-scale integrated (VLSI) circuitry that could process data in real time.

Duong, Tuan↗

Enabling Future Robotic Missions with Multicore Processors

Recent commercial developments in multicore processors (e.g. Tilera, Clearspeed, HyperX) have provided an option for high performance embedded computing that rivals the performance attainable with FPGA-based reconfigurable computing architectures. Furthermore, these processors offer more straightforward and streamlined application development by allowing the use of conventional programming languages and software tools in lieu of hardware design languages such as VHDL and Verilog. With these advantages, multicore processors can significantly enhance the capabilities of future robotic space missions. This paper will discuss these benefits, along with onboard processing applications where multicore processing can offer advantages over existing or competing approaches. This paper will also discuss the key artchitecural features of current commercial multicore processors. In comparison to the current art, the features and advancements necessary for spaceflight multicore processors will be identified. These include power reduction, radiation hardening, inherent fault tolerance, and support for common spacecraft bus interfaces. Lastly, this paper will explore how multicore processors might evolve with advances in electronics technology and how avionics architectures might evolve once multicore processors are inserted into NASA robotic spacecraft.

multi-core processor↗

Telescience at the University of California, Berkeley

The University of California at Berkeley (UCB) is a member of a university consortium involved in telescience testbed activities under the sponsorship of NASA. The Telescience Testbed Project consists of three experiments using flight hardware being developed for the Extreme Ultraviolet Explorer project at UCB's Space Sciences Laboratory. The first one is a teleoperation experiment investigating remote instrument control using a computer network such as the Internet. The second experiment is an effort to develop a system for operation of a network of remote workstations allowing coordinated software development, evaluation, and use by widely dispersed groups. The final experiment concerns simulation as a method to facilitate the concurrent development of instrument hardware and support software. Progress in these areas is described.

Chakrabarti, S.↗