Search NASA⌕ Search

SEARCH · Search NASA

Results for “Process sensitivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Search for the Standard Model Higgs Boson associated with a W Boson using Matrix Element Technique in the CDF detector at the Tevatron

In this thesis a direct search for the Standard Model Higgs boson production in association with a W boson at the CDF detector in the Tevatron is presented. This search contributes predominantly in the region of low mass Higgs region, when the mass of Higgs boson is less than about 135 GeV. The search is performed in a final state where the Higgs boson decays into two b quarks, and the W boson decays leptonically, to a charged lepton (it can be an electron or a muon) and a neutrino. This work is organized as follows. Chapter 2 gives an overview of the Standard Model theory of particle physics and presents the SM Higgs boson search results at LEP, and the Tevatron colliders, as well as the prospects for the SM Higgs boson searches at the LHC. The dataset used in this analysis corresponds to 4.8 fb -1 of integrated luminosity of p$\bar{p}$ collisions at a center of mass energy of 1.96 TeV. That is the luminosity acquired between the beginning of the CDF Run II experiment, February 2002, and May 2009. The relevant aspects, for this analysis, of the Tevatron accelerator and the CDF detector are shown in Chapter 3. In Chapter 4 the particles and observables that make up the WH final state, electrons, muons, E T , and jets are presented. The CDF standard b-tagging algorithms to identify b jets, and the neural network flavor separator to distinguish them from other flavor jets are also described in Chapter 4. The main background contributions are those coming from heavy flavor production processes, such as those coming from Wbb, Wcc or Wc and tt. The signal and background signatures are discussed in Chapter 5 together with the Monte CArlo generators that have been used to simulate almost all the events used in this thesis. WH candidate events have a high-p T lepton (electron or muon), high missing transverse energy, and two or more than two jets in the final state. Chapter 6 describes the event selection applied in this analysis and the method used to estimate the background contribution. The Matrix Element method, that was successfully used in the single top discovery analysis and many other analyses within the CDF collaboration, is the multivariate technique used in this thesis to discriminate signal from background events. With this technique is possible to calculate a probability for an event to be classified as signal or background. These probabilities are then combined into a discriminant function called the Event Probability Discriminant, EPD, which increases the sensitivity of the WH process. This method is described in detail in Chapter 7. As no evidence for the signal has been found, the results obtained with this work are presented in Chapter 8 in terms of exclusion regions as a function of the mass of the Higgs boso, taking into account the full systematics. The conclusions of this work to obtain the PhD are presnted in Chapter 9.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

2020 State of the Science Report, Chapter 12: Adaptive Management Related to Marine Renewable Energy

As the marine renewable energy (MRE) industry is rapidly ramped up from single devices to commercial-scale deployments, developers and regulators will need evidence of the environmental effects of MRE to inform project development and consenting/permitting (hereafter consenting) processes. Uncertainty surrounding the potential impacts of novel RE technologies on sensitive marine animals, habitats, and ecosystem processes means that even robust baseline environmental information cannot comprehensively address all pre-deployment knowledge gaps. Tools and practical approaches are needed to help with the sustainable development of the industry. Adaptive management (AM), also referred to as learning by/while doing, enables projects to be deployed incrementally, despite uncertainty, in a way that prevents unacceptable harm to the marine environment. If rigorously implemented, this approach may provide a reliable mechanism for closing knowledge gaps, thereby retiring risks for future MRE developments. This chapter explores and suggests a pathway for applying a passive approach to AM for the consenting of single devices and array-scale MRE projects. Complementary information is available online at https://tethys.pnnl.gov/state-of-thescience-2020 -supplementaryadaptive-management. https://tethys.pnnl.gov/publications/state-of-the-science-2020-chapter-12-adaptive-management

16 TIDAL AND WAVE POWER↗

A complementary MOS process

The complete sequence used to manufacture complementary metal oxide semiconductor (CMOS) integrated circuits is described. The fixed-gate array concept is presented as a means of obtaining CMOS integrated circuits in a fast and reliable fashion. Examples of CMOS circuits fabricated by both the conventional method and the fixed-gate array method are included. The electrical parameter specifications and characteristics are given along with typical values used to produce CMOS circuits. Temperature-bias stressing data illustrating the thermal stability of devices manufactured by this process are presented. Results of a preliminary study on the radiation sensitivity of circuits manufactured by this process are discussed. Some process modifications are given which have improved the radiation hardness of our CMOS devices. A formula description of the chemicals and gases along with the gas flow rates is also included.

Jhabvala, M. D.↗

ATOMIC FORCE LITHOGRAPHY OF NANO MICROFLUIDIC CHANNELS FOR VERIFICATION AND MONITORING IN AQUEOUS SOLUTIONS

The growing interest in the physics of fluidic flow in nanoscale channels, as well as the possibility for high sensitive detection of ions and single molecules is driving the development of nanofluidic channels. The enrichment of charged analytes due to electric field-controlled flow and surface charge/dipole interactions along the channel can lead to enhancement of sensitivity and limits-of-detection in sensor instruments. Nuclear material processing, waste remediation, and nuclear non-proliferation applications can greatly benefit from this capability. Atomic force microscopy (AFM) provides a low-cost alternative for the machining of disposable nanochannels. The small AFM tip diameter (< 10 nm) can provide for features at scales restricted in conventional optical and electron-beam lithography. This work presents preliminary results on the fabrication of nano/microfluidic channels on polymer films deposited on quartz substrates by AFM lithography.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Role of surface hydroxyl groups in promoting room temperature CO sensing by Pd-modified nanocrystalline SnO{sub 2}

SnO{sub 2}/Pd nanocomposites were synthesized via sol-gel method followed by variable processing procedures. The materials are sensitive to CO gas in the concentration range 2-100 ppm at room operating temperature. It was shown that modification of nanocrystalline tin dioxide by Pd changes the temperature dependence of sensor response, decreasing the temperature of maximal signal. To understand the mechanism of room temperature CO sensitivity, a number of SnO{sub 2}/Pd materials were characterized by XRD, TEM, BET, XPS and TPR techniques. From the results of FTIR, impedance and sensing measurements under variable ambient conditions it was concluded that improvement in CO sensitivity for Pd-modified SnO{sub 2} is due to alteration of CO oxidation pathway. The reaction of CO with surface OH-groups at room temperature was proposed, the latter being more reactive than oxygen species due to the possible chain character of the reactions. It was proposed that Pd additive may initiate chain processes at room temperature. - Graphical abstract: Nanocrystalline SnO{sub 2} modified by PdO/Pd clusters exhibit high CO sensitivity at room temperature. An extensive study revealed surface OH-groups participation in CO oxidation on SnO{sub 2} leading to enhanced sensitivity at low operating temperature (25-150 {sup o}C). PdO/Pd clusters supposedly initiate a chain of CO reactions with surface hydroxyls.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Structural and dynamical studies of acid-mediated conversion in amorphous-calcium-phosphate based dental composites

Our objective was to investigate the complex structural and dynamical conversion process of the amorphous-calcium-phosphate (ACP)-to-apatite transition in ACP based dental composite materials. Composite disks were prepared using zirconia hybridized ACP fillers (0.4 mass fraction) and photo-activated Bis-GMA/TEGDMA resin (0.6 mass fraction). We performed an investigation of the solution-mediated ACP-to-apatite conversion mechanism in controlled acidic aqueous environment with in situ ultra-small angle X-ray scattering based coherent X-ray photon correlation spectroscopy and ex situ X-ray diffraction, as well as other complementary techniques. We established that the ACP-to-apatite conversion in ACP composites is a two-step process, owing to the sensitivity to local structural changes provided by coherent X-rays. Initially, ACP undergoes a local microstructural rearrangement without losing its amorphous character. We established the catalytic role of the acid and found the time scale of this rearrangement strongly depends on the pH of the solution, which agrees with previous findings about ACP without the polymer matrix being present. In the second step, ACP is converted to an apatitic form with the crystallinity of the formed crystallites being poor. Separately, we also confirmed that in the regular Zr-modified ACP the rate of ACP conversion to hydroxyapatite is slowed significantly compared to unmodified ACP, which is beneficial for targeted slow release of functional calcium and phosphate ions from dental composite materials. Significantly, for the first time, we were able to follow the complete solution-mediated transition process from ACP to apatite in this class of dental composites in a controlled aqueous environment. A two-step process, suggested previously, was conclusively identified.

36 MATERIALS SCIENCE↗

Interfacial diffusion aided deformation during nanoindentation

Nanoindentation is commonly used to quantify the mechanical response of material surfaces. Despite its widespread use, a detailed understanding of the deformation mechanisms responsible for plasticity during these experiments has remained elusive. Nanoindentation measurements often show stress values close to a material’s ideal strength which suggests that dislocation nucleation and subsequent dislocation activity dominates the deformation. However, low strain-rate exponents and small activation volumes have also been reported which indicates high temperature sensitivity of the deformation processes. Using an order parameter aided temperature accelerated sampling technique called adiabatic free energy dynamics [J. B. Abrams and M. E. Tuckerman, J. Phys. Chem. B, 112, 15742 (2008)], and molecular dynamics we have probed the diffusive mode of deformation during nanoindentation. Localized processes such as surface vacancy and ad-atom pair formation, vacancy diffusion are found to play an important role during indentation. Our analysis suggests a change in the dominant deformation mode from dislocation mediated plasticity to diffusional flow at high temperatures, slow indentation rates and small indenter tip radii.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Plant-specific Model and Data Analysis using Dynamic Security Modeling and Simulation

The requirements for U.S. nuclear power plants to maintain a large on-site physical security force contribute to their high operational costs. The cost of maintaining the current physical security posture is approximately 10% of the overall operation and maintenance budget for commercial nuclear power plants. The goal of the Light Water Reactor Sustainability (LWRS) program’s physical security pathway is to develop tools, methods, and technologies and provide the technical basis for an optimized physical security posture. The conservatisms built into current security postures may be analyzed and minimized in order to reduce security costs while still ensuring adequate security and operational safety. The research performed at Idaho National Laboratory within LWRS program’s physical security pathway has successfully developed a dynamic force-on-force modeling framework using various computer simulation tools and integrating them with the dynamic assessment Event Modeling Risk Assessment using Linked Diagrams (EMRALD) tool. This document provides an update on the progress in applying a dynamic computational framework that links results from a commercially available force-on-force simulation tool, a commercially available thermal-hydraulic tool, and EMRALD to an operating commercial nuclear power plant. This report is only a summary of the progress and does not contain specific modeling results as those contain sensitive security information. This process of including plant procedures and multiple analysis results is being called Modeling and Analysis for Safety Security using Dynamic EMRALD Framework or MASS-DEF. Previous reports described how a user could integrate their plant-specific force-on-force models with the dynamic simulation tool EMRALD, model operator actions, integrate with probabilistic risk assessment tools, such as CAFTA (Computer Aided Fault Tree Analysis System) or SAPHIRE (Systems Analysis Programs for Hands-on Integrated Reliability Evaluations), and with thermal-hydraulic tools, such as RELAP-5. Previous reports applied various combinations of available simulations codes with EMRALD using generic plant models to demonstrate how to perform the analysis. This report documents the results of applying the dynamic computational framework to an actual nuclear facility using their security scenarios and timelines. This report does not contain any plant's sensitive information and/or Safeguards Information. The purpose of this study was to verify that results achieved using generic models are similar to actual plant results and to refine our guidance on the use of the framework. This assessment enables further analysis, such as what-if scenarios and staff-reduction evaluation, thereby optimizing physical security at plants.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Neutron Capture on 130 Sn during r-Process Freeze-Out

We examine the role of neutron capture on {sup 130}Sn during r-process freeze-out in the neutrino-driven wind environment of the core-collapse supernova. We find that the global r-process abundance pattern is sensitive to the magnitude of the neutron capture cross section of {sup 130}Sn. The changes to the abundance pattern include not only a relative decrease in the abundance of {sup 130}Sn and an increase in the abundance of {sup 131}Sn, but also a shift in the distribution of material in the rare earth and third peak regions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Friction Stir Welding of Tapered Thickness Welds Using an Adjustable Pin Tool

Friction stir welding (FSW) can be used for joining weld lands that vary in thickness along the length of the weld. An adjustable pin tool mechanism can be used to accomplish this in a single-pass, full-penetration weld by providing for precise changes in the pin length relative to the shoulder face during the weld process. The difficulty with this approach is in accurately adjusting the pin length to provide a consistent penetration ligament throughout the weld. The weld technique, control system, and instrumentation must account for mechanical and thermal compliances of the tooling system to conduct tapered welds successfully. In this study, a combination of static and in-situ measurements, as well as active control, is used to locate the pin accurately and maintain the desired penetration ligament. Frictional forces at the pin/shoulder interface were a source of error that affected accurate pin position. A traditional FSW pin tool design that requires a lead angle was used to join butt weld configurations that included both constant thickness and tapered sections. The pitch axis of the tooling was fixed throughout the weld; therefore, the effective lead angle in the tapered sections was restricted to within the tolerances allowed by the pin tool design. The sensitivity of the FSW process to factors such as thickness offset, joint gap, centerline offset, and taper transition offset were also studied. The joint gap and the thickness offset demonstrated the most adverse affects on the weld quality. Two separate tooling configurations were used to conduct tapered thickness welds successfully. The weld configurations included sections in which the thickness decreased along the weld, as well as sections in which the thickness increased along the weld. The data presented here include weld metallography, strength data, and process load data.

Adams, Glynn↗

Tidal frequencies and quasiperiodic subsurface water level variations dominate redox dynamics in a salt marsh system

Salt marshes are hotspots of nutrient processing en route to sensitive coastal environments. Whilst our understanding of these systems has improved over the years, we still have limited knowledge of the spatiotemporal variability of critical biogeochemical drivers within salt marshes. Sea-level rise will continue to force change on salt marsh functioning, highlighting the urgency of filling this knowledge gap. Our study was conducted in a central California estuary experiencing extensive marsh drowning and relative sea-level rise, making it a model system for such an investigation. Here we instrumented three marsh positions subjected to different degrees of tidal inundation (6.7%, 8.9%, and 11.2% of the time for the upper, middle, and lower marsh positions, respectively), providing locations with varied biogeochemical characteristics and hydrological interactions at the site. We continuously monitored redox potential (Eh) at depths of 0.1, 0.3, and 0.5 m, subsurface water levels (WL), and temperature at 0.7 m depth at each marsh position. To understand how drivers of subsurface biogeochemical processes fluctuate across tidal cycles, we used wavelet analyses to explain the interactions between Eh and WL. We found that tidal forcing significantly affects key drivers of biogeochemical processes by imparting controls on Eh variability, likely driving subsurface hydro-biogeochemistry of the salt marsh. Wavelet coherence showed that the Eh-WL relationship is nonlinear, and their lead–lag relationship is variable. We found that precipitation events perturb Eh at depth over timescales of hours, even though WL shows relatively minimal change during events. Furthermore, this work highlights the importance of high frequency in situ measurements, such as Eh, to help explain factors that govern subsurface biogeochemistry and hydrological processes in salt marshes.

54 ENVIRONMENTAL SCIENCES↗

Projected Cost, Energy Use, and Emissions of Hydrogen Technologies for Fuel Cell Vehicles

Each combination of technologies necessary to produce, deliver, and distribute hydrogen for transportation use has a corresponding levelized cost, energy requirement, and greenhouse gas emission profile depending upon the technologies' efficiencies and costs. Understanding the technical status, potential, and tradeoffs is necessary to properly allocate research and development (R&D) funding. In this paper, levelized delivered hydrogen costs, pathway energy use, and well-to-wheels (WTW) energy use and emissions are reported for multiple hydrogen production, delivery, and distribution pathways. Technologies analyzed include both central and distributed reforming of natural gas and electrolysis of water, and central hydrogen production from biomass and coal. Delivery options analyzed include trucks carrying liquid hydrogen and pipelines carrying gaseous hydrogen. Projected costs, energy use, and emissions for current technologies (technology that has been developed to at least the bench-scale, extrapolated to commercial-scale) are reported. Results compare favorably with those for gasoline, diesel, and E85 used in current internal combustion engine (ICE) vehicles, gasoline hybrid electric vehicles (HEVs), and flexible fuel vehicles. Sensitivities of pathway cost, pathway energy use, WTW energy use, and WTW emissions to important primary parameters were examined as an aid in understanding the benefits of various options. Sensitivity studies on production process energy efficiency, total production process capital investment, feed stock cost, production facility operating capacity, electricity grid mix, hydrogen vehicle market penetration, distance from the hydrogen production facility to city gate, and other parameters are reported. The Hydrogen Macro-System Model (MSM) was used for this analysis. The MSM estimates the cost, energy use, and emissions trade offs of various hydrogen production, delivery, and distribution pathways under consideration. The MSM links the H2A Production Model, the Hydrogen Delivery Scenario Analysis Model (HDSAM), and the Greenhouse Gas, Regulated Emission, and Energy for Transportation (GREET) Model. The MSM utilizes the capabilities of each component model and ensures the use of consistent parameters between the models to enable analysis of full hydrogen production, delivery, and distribution pathways. To better understand spatial aspects of hydrogen pathways, the MSM is linked to the Hydrogen Demand and Resource Analysis Tool (HyDRA). The MSM is available to the public and enables users to analyze the pathways and complete sensitivity analyses.

08 HYDROGEN↗

Method for lithograghic patterning of sensitive materials

Methods for patterning highly sensitive materials, such as organic materials, organic semiconductors, biomolecular materials, and the like, with photolithographic resolution are disclosed. In some embodiments, a germanium mask (304) is formed on the surface of the sensitive material (302), thereby protecting it from subsequent processes that employ harsh chemicals that would otherwise destroy the sensitive material (302). A microlithography mask (306) is patterned on the germanium mask layer (304), after which the germanium exposed by the microlithography mask (306) is removed by dissolving it in water. After transferring the pattern of the germanium mask (304) into the sensitive material (302), the germanium and microlithography masks (304, 306) are completely removed by immersing the substrate in water, which dissolves the remaining germanium and lifts off the microlithography mask material. As a result, the only chemical to which the sensitive material (302) is exposed during the patterning process is water, thereby mitigating or avoiding damage to the material (302).

36 MATERIALS SCIENCE↗

'Edge illumination' in X-ray Phase Contrast Imaging

In the late '90s, the concept of 'edge illumination' was developed at ELETTRA in Italy as an alternative method to increase the phase sensitivity of an imaging system. The main idea was to be able to reproduce the fine angular selection of 'analyzer' crystals without actually using a crystal, as this would allow employing the method with divergent and polychromatic (i.e. conventional) x-ray sources. It was observed that this could be achieved by illuminating only the edges of the detector pixels, and that the method's sensitivity could be progressively increased by illuminating smaller pixel fractions closer to its physical edge. A few years later the idea was adapted for use with a conventional source by means of two sets of x-ray masks ('coded aperture' masks), which enabled obtaining the same effect for each row (or column) of pixels of an area detector illuminated by a cone beam. This article reviews the method and presents recent examples of application.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Why are we still using 3D masses for cluster cosmology?

ABSTRACT The abundance of clusters of galaxies is highly sensitive to the late-time evolution of the matter distribution, since clusters form at the highest density peaks. However, the 3D cluster mass cannot be inferred without deprojecting the observations, introducing model-dependent biases and uncertainties due to the mismatch between the assumed and the true cluster density profile and the neglected matter along the sightline. Since projected aperture masses can be measured directly in simulations and observationally through weak lensing, we argue that they are better suited for cluster cosmology. Using the Mira–Titan suite of gravity-only simulations, we show that aperture masses correlate strongly with 3D halo masses, albeit with large intrinsic scatter due to the varying matter distribution along the sightline. Nonetheless, aperture masses can be measured ≈2–3 times more precisely from observations, since they do not require assumptions about the density profile and are only affected by the shape noise in the weak lensing measurements. We emulate the cosmology dependence of the aperture mass function directly with a Gaussian process. Comparing the cosmology sensitivity of the aperture mass function and the 3D halo mass function for a fixed survey solid angle and redshift interval, we find the aperture mass sensitivity is higher for Ωm and $w_a$, similar for σ8, ns, and $w_0$, and slightly lower for h. With a carefully calibrated aperture mass function emulator, cluster cosmology analyses can use cluster aperture masses directly, reducing the sensitivity to model-dependent mass calibration biases and uncertainties.

79 ASTRONOMY AND ASTROPHYSICS↗

Extrusion‐Spheronization of Energetic Materials

The prevailing method to produce plastic‐bonded explosive (PBX) molding powder, or “prills”, is a complex, multiphase, and bespoke process that was developed by the high explosives (HEs) manufacturing industry several decades ago. This work demonstrates the utility of a simpler, widely‐used mechanical process—extrusion‐spheronization—to produce PBX prills. We begin by detailing precautions taken to enable safe remote operation of extrusion‐spheronization equipment with HE. We then perform a study investigating the effect of lacquer solvent composition on the particle packing, pressed density, and compressive strength properties of a 95 wt.% TATB/5 wt.% polymer binder formulation akin to PBX 9502. It was found that increased composition of low vapor pressure solvents caused prolonged retention of the solvent, resulting in tackier materials that would agglomerate and form larger prills. The larger prills also led to lower poured density and tapped density of HE prills and compressive strength of pressed PBX articles. The samples prepared with a 75% propyl acetate/25% butyl acetate lacquer solvent composition exhibited the highest compressive strength. However, it is believed that the prill packing and compressive strength properties are primarily driven by the prill size rather than the chemical composition of the lacquer itself. Extrusion‐spheronization remains a promising method to reliably and repeatably produce HE prills that is less sensitive to feedstock or process variation than traditional methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

SPND Sensitivity Calculations Using MCNP and Experimental Data from ACRR

The use of the Monte Carlo N-Particle Transport Code (MCNP) to calculate detector sensitivity for Self-Powered Neutron Detectors (SPNDs) in the Annular Core Research Reactor (ACRR) could be a vital tool in the effort to optimize the design of next-generation SPNDs. Next-generation SPND designs, which consider specific materials and geometry, may provide experimenters with capabilities for advanced mixed field dosimetry. These detectors will need to be optimized for configuration, materials, and geometries and the ability to model and iterate must be available in order to decide on the ideal. SPND design. SPNDs were modeled in MCNP which closely resembled the dimensions and location of actual detectors used in the ACRR. Tallies were used to calculate detector sensitivity. Using metrics from a previous report, oscilloscope data from pulses were manipulated in a Matrix Laboratory computing environment (MATLAB) script to calculate experimental detector sensitivity. This report outlines the process in which experimental data from ACRR pulses verified results from tallies in an MCNP ACRR model. The sensitivity values from experiments and MCNP calculations agreed within one standard deviation. Parametric studies were also performed with MCNP to investigate the effects of materials and dimensions of different SPNDs.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Fully depleted CMOS pixel sensor development and potential applications

CMOS pixel sensors are often opposed to hybrid pixel sensors due to their very different sensitive layer. In standard CMOS imaging processes, a thin (about 20 μm) low resistivity epitaxial layer acts as the sensitive volume and charge collection is mostly driven by thermal agitation. In contrast, the so-called hybrid pixel technology exploits a thick (typically 300 μm) silicon sensor with high resistivity allowing for the depletion of this volume, hence charges drift toward collecting electrodes. But this difference is fading away with the recent availability of some CMOS imaging processes based on a relatively thick (about 50 μm) high resistivity epitaxial layer which allows for full depletion. This evolution extents the range of applications for CMOS pixel sensors where their known assets, high sensitivity and granularity combined with embedded signal treatment, could potentially foster breakthrough in detection performances for specific scientific instruments. One such domain is the Xray detection for soft energies, typically below 10 keV, where the thin sensitive layer was previously severely impeding CMOS sensor usage. Another application becoming realistic for CMOS sensors, is the detection in environment with a high fluence of non-ionizing radiation, such as hadron colliders. However, when considering highly demanding applications, it is still to be proven that micro-circuits required to uniformly deplete the sensor at the pixel level, do not mitigate the sensitivity and efficiency required. Prototype sensors in two different technologies with resistivity higher than 1 kΩ, sensitive layer between 40 and 50 μm and featuring pixel pitch in the range 25 to 50 μm, have been designed and fabricated. Various biasing architectures were adopted to reach full depletion with only a few volts. Laboratory investigations with three types of sources (X-rays, β-rays and infrared light) demonstrated the validity of the approach with respect to depletion, keeping a low noise figure. Especially, an energy resolution of about 400 eV for 5 keV X-rays was obtained for single pixels. The prototypes have then been exposed to gradually increased fluences of neutrons, from 10{sup 13} to 5x10{sup 14} neq/cm{sup 2}. Again laboratory tests allowed to evaluate the signal over noise persistence on the different pixels implemented. Currently our development mostly targets the detection of soft X-rays, with the ambition to develop a pixel sensor matching counting rates as affordable with hybrid pixel sensors, but with an extended sensitivity to low energy and finer pixel about 25 x 25 μm{sup 2}. The original readout architecture proposed relies on a two tiers chip. The first tier consists of a sensor with a modest dynamic in order to insure low noise performances required by sensitivity. The interconnected second tier chip enhances the read-out speed by introducing massive parallelization. Performances reachable with this strategy combining counting and integration will be detailed. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗