Search NASA⌕ Search

SEARCH · Search NASA

Results for “CERAMICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Increasing Multilayer Ceramic Capacitor Lifetime With Bipolar Voltage Cycling

Enhancing the lifetime of multilayer ceramic capacitors (MLCCs) is critical in many aerospace, naval, or electrical grid applications, where device failure could lead to catastrophic consequences. The migration of oxygen vacancies from the ceramic to the electrode interface under constant bias is known to reduce the lifetime of oxide-based MLCCs. Bias cycling presents an opportunity to enhance MLCC lifetime by reducing oxygen vacancy migration. The ideal frequency range is expected to lie between frequencies low enough to avoid self-heating but high enough to avoid interfacial defect formation. However, the impact of low-frequency bipolar voltage cycling (BVC) on MLCC degradation mechanisms has not been well studied. This work investigates the impact of periodic BVC on the degradation of MLCCs through highly accelerated lifetime testing (HALT) on X7R capacitors. HALT tests were conducted at 255 °C and 60 V using different switching frequencies: 0 (dc), 0.1, 2.5, and 10 Hz. BVC was found to improve the lifetime of MLCCs compared to dc test conditions. MLCCs tested at 10-Hz BVC showed a 311% increase in average time to failure compared to the dc case. Impedance spectroscopy shows that BVC decreases the rate of resistance degradation within MLCCs, indicating that oxygen vacancy migration to the electrodes is mitigated. The impedance spectra taken on BVC samples highlight how grain boundaries play a vital role in trapping oxygen vacancies. Periodic cycling causes oxygen vacancies to become trapped at grain boundaries, resulting in oxygen vacancies taking longer to reach the electrode interface and thus increasing MLCC lifetime. This work highlights not only how BVC can be used to increase MLCC lifetime but also how periodically cycling MLCCs could increase lifetime in extreme environments, such as at elevated temperatures and electric fields.

Chuong, Kayla Y.↗
DOE OSTI2025

Redesigning protonic ceramic electrochemical cells to lower the operating temperature

Protonic ceramic electrochemical cells (PCECs) can operate at intermediate temperatures (450° to 600°C) for power generation and hydrogen production. However, the operating temperature is still too high to revolutionize ceramic electrochemical cell technology. Lowering the operating temperature to <450°C will enable a wider material choice and reduce system costs. We present approaches to redesigning PCECs via readily fabricated single-grain–thick, chemically homogeneous, and robust electrolytes and a nano-micro positive electrode. At 450°C, the PCECs achieve a peak power density of 1.6 watt per square centimeter on H 2 fuel, 0.5 watt per square centimeter on NH 3 fuel, and 0.3 watt per square centimeter on CH 4 fuel in fuel cell mode. In steam electrolysis mode, a current density of >0.6 ampere per square centimeter with a Faradaic efficiency of >90% is achievable at 1.4 volt and 400°C. In addition, exceptional durability (>2000 hours) has been demonstrated, with a degradation rate of <0.01 millivolt per 100 hours in fuel cell mode at 400°C.

Science & Technology - Other Topics↗
DOE OSTI2024

Modeling In-Reactor Temperature Gradients in Lithium Aluminate Ceramic Pellets

In reactor thermal performance of lithium aluminate ceramic pellets are calculated to determine operating temperatures if internal components shift during irradiation. A 2D conduction model was setup to model this scenario with additional physics, including thermal expansion of components to reactor temperatures, creep down of the cladding due to differential pressure between the inside of the rod and reactor coolant system, and net radiation exchange between components. The non-linear coupling of the governing equations presented convergence challenges due to the very different effects from a small temperature change on the radiation vs radial and circumferential conduction equations. Initial temperature guesses for the multidimensional solution were provided from conservative 1D models simulating bounding scenarios. Convergence was greatly improved by taking small steps towards the root solutions and averaging with initial guesses. The final method robustly converged all 132 points at an axial plane after a few dozen iterations. The temperature results show that the additional physics have a secondary effect as the dominant heat transfer mechanism is radial conduction across the gas gap followed by circumferential conduction around components. Circumferential conduction in the lithium aluminate pellets is enhanced by the relatively high thermal conductivity of this ceramic.

Carstens, Nathan A.↗
DOE OSTI2024

Modularization of Ceramic Hollow Fiber Membrane Technology for Air Separation

This proposed project is aimed at studying high performance and economically competitive ceramic membrane technology for air separation and high-purity oxygen production using hollow fiber ceramic membrane stack and module technology. The design of the single permeate membrane is a hollow fiber substrate-supported thin tri-layer structure. Radially well-aligned micro-channels are embedded in the thick substrate and open at the inner surface of the substrate, enabling facile air/gas diffusion. The tri-layer structure of thin dense membrane layer (~ 10 µm) sandwiched by porous surface layer on either side is then built on the substrate using advanced fabrication process. The tri-layer structure design allows different materials to be used in different layers, where the materials of surface layers have high surface exchange coefficients while the material of dense layer has high bulk diffusivity. Such a synergetic combination leads to high permeation performance. The focus of the proposed project will be on membrane stack/module development using the developed single hollow fiber membranes, including: 1) fabrication and characterization of novel single hollow fiber membranes; 2) membrane stack design and assembly using fabricated single membranes; 3) stack modeling and analysis to guide membrane stack designs; 4) permeation performance testing and characterization of membrane stacks. The hollow fiber feature and simple sealing requirement enable very compact design of membrane stacks, which have excellent flexibility for further modularizations at different scales. The operations of such membrane stack and module may employ the exhaust heat from other components of Integrated Gasification Combined Cycle and oxy-combustion systems. Therefore, modularization of such an air separation membrane technology can be incorporated into the DOE’s REMS (radically engineered modular systems)-gasification skid and support the oxidant feed of an oxygen-blown REMS gasifier scaled to different ranges.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

Near-net shaping of high-density, complex, spatially-tailored ceramics for extreme environments

The purpose of this subcontract is for LLNL to collaborate with the Subcontractor (UCSB) in the areas of binder jet additive manufacturing (BJAM), hot pressing (HP), finite element modeling (FEM), and multi-material sintering studies. LLNL wants to further develop its hot pressing, AM, and modeling capabilities through LLNL’s Early Career Faculty Program. This work will focus on developing a method to hot press complex-shaped ceramic parts through the co-deposition of a structural/functional ceramic and sacrificial mold material in one assembly via multi-material binder jet printing. The method aims to produce dense, near-net shaped parts with applications relevant to a wide variety of fields including aerospace, defense, and energy.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Direct Processing of Lithium Chloride Based Waste Salt in a Ceramic Waste Form

Ceramic waste form materials were fabricated with a LiCl based salt mixture to demonstrate the suitability of direct processing of waste salt from an all LiCl pyroprocessing flow sheet on the formation, microstructure, and durability of ceramic waste forms. Materials were successfully synthesized by using the simplified direct processing technique with salt loadings of 5, 7.5, and 10 wt% at the laboratory scale. Materials fabricated with LiCl based salt indicated full conversion of zeolite to sodalite occurred to form products with low open porosity. This indicates that the Na 2 O content of NBS4 glass is suitable for processing salt chemistries which do not contain NaCl. Generated sodalite was microencapsulated by the glass binder, halite occlusions were detected within sodalite domains at all salt loadings, and a Cs-rich phase believed to be Cs-pollucite was detected in the material made with the lowest salt loading (5 wt%). Salt inclusions were encapsulated within the binder glass at all loadings, and found to consist primarily of NaCl with Cs present. A small amount of salt was found at the surface of the wasteform made with the highest salt loading of 10 wt%, which may indicate an upper limit to the amount of salt that can be accommodated or incomplete mechanical mixing of the reagents. Durability testing by using the ASTM C1308 method indicated that initial rapid dissolution of exposed halite inclusion phases was directly correlated to salt loading. Wasteform degradation during all tests occurred primarily due to dissolution of the sodalite phase. Durability of the binder glass was found to increase as the waste salt loading increased. Results for the release of cations from the salt indicate the changes in wasteform durability and halite inclusion chemistry are strongly influenced by ion exchange phenomena between the salt and the glass. This appears to be the result of the relatively stronger affinity for the glass phase of Li, compared to that of other cations such as Na and Cs. The effects from cation exchange were diminished at lower salt loadings.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Ceramic Composite Experimental Testing Status

Over recent years, ceramic matrix materials such as SiC–SiC and C–C have been gaining interest for use in fusion reactors, light water reactors (LWRs), and high-temperature reactors (HTRs). These materials are good candidates to operate in very high temperature and moderate to high radiation environments. The evaluation of composite materials, in general, is challenging because of variations in precursor materials, variations in the fabrication process across fabricators, and the wide range of potential fiber architectures, to name a few. However, the need to evaluate neutron-irradiated properties adds another layer of complexity, which includes cost, timeline, and specimen size limitations (often associated with irradiation testing). A qualification methodology for the use of ceramic composites is provided in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code Section III-5-HHB. The methodology is supported by ASTM International (ASTM) guides, which provide a pathway to accomplish this effort. Part of the qualification strategy is for the designer to collect material property data on environmental conditions representative of its design envelope. These data include irradiation effects. This report presents an experimental study and test campaign developed to partially address this gap by providing initial mechanical and physical property data required for design. A variety of different materials using different manufacturing techniques are considered as part of this campaign. The test plan suggests performing a screening or partial irradiation study to assist the designer during the material selection process. The designer can then perform a more comprehensive qualification study if the material performance is promising. This work focuses on the status of the specimen preparations (machining of samples), the current test methods and failure analysis as well as the preparation of irradiation vehicles for the irradiation campaign. The irradiation will be performed at Oak Ridge National Laboratory (ORNL) in the High Flux Isotope Reactor (HFIR) and at Idaho National Laboratory (INL) in the Advanced Test Reactor (ATR).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Elastic Modulus Measurement at High Temperatures for Miniature Ceramic Samples Using Laser Micro-Machining and Thermal Mechanical Analyzer

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale at high temperatures. We used a picosecond laser to precisely cut microbeams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm and a length of ~1 cm. They were then tested in a thermal mechanical analyzer at room temperature, 500 °C, 800 °C, and 1100 °C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

Chemistry↗
DOE OSTI2024

Glass-ceramic matrix composite feedstock and forming

A method of forming a part includes forming a glass-ceramic matrix composite material to form a pre-consolidated feedstock sheet with a pre-determined shape. The pre-consolidated feedstock sheet is sectioned into a first piece of pre-consolidated feedstock sheet and a second piece of pre-consolidated feedstock sheet. The first piece of pre-consolidated feedstock sheet and a second piece of pre-consolidated feedstock sheet are assembled with a second piece of pre-consolidated feedstock sheet to form a composite layup. The first piece of pre-consolidated feedstock sheet and the second piece of pre-consolidated feedstock sheet are joined by compressing the composite layup to form a glass-ceramic matrix composite part.

Gangloff, Jr., John J.↗
DOE OSTI2026

Improving protonic ceramic electrochemical cell performance via a dual-phase reaction-sintered bilayer electrolyte

Protonic ceramic electrochemical cells (PCCs) are promising energy conversion devices, but their fabrication remains challenging. In particular, the typical electrolytes for PCCs such as BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3−δ (7111) and BaCe 0.4 Zr 0.4 Y 0.1 Yb 0.1 O 3−δ (4411) suffer from intrinsic barium evaporation issues during high-temperature sintering. This tendency towards barium loss, combined with their highly refractory nature, leads to a tradeoff between sinterability and chemical stability. To address this tradeoff, we propose a bilayer electrolyte combining layers of 4411 and 7111 materials that is designed to enhance sinterability and conductivity through dual-phase reactive sintering. Our findings demonstrate that the bilayer structure exhibits shrinkage behavior closely matched to that of the fuel electrode substrate, with a higher shrinkage compared to a single-layer 4411 electrolyte. Utilizing this bilayer electrolyte structure, our PCCs achieve a peak power density of 637 mW∙cm −2 in fuel-cell mode and a current density of 1060 mA∙cm −2 at 1.3 V in electrolysis mode at 600 °C. Our PCCs demonstrate high Faradaic efficiency of 83% at 1.3 V and 500 °C. Hybrid distribution of relaxation times (DRT) polarization mapping further reveals that the bilayer structure reduces Ohmic and polarization resistance in both fuel-cell and electrolysis modes.

ceramic processing↗
DOE OSTI2024

Reverse Polarizability of Rare Earth Ions (La 3+ , Gd 3+ , Lu 3+ , Y 3+ ) in Tellurite Glasses and Glass Ceramics for Optical Limiting

All-optical modulation using inherent third-order optical nonlinearity of a medium has garnered considerable interest in photonics and optoelectronics. Herein, nonlinear optical (NLO) properties of tellurite glasses and glass ceramics (GCs) containing four different rare earths (RE = La, Gd, Lu, and Y) have been deliberated in near-infrared regions under an ultrafast regime. The La-based glass exhibits ~10 times higher nonlinear refraction (n 2 ) and absorption (α 2 ) than reported NLO materials. The NLO susceptibility [χ (3) ] trend in the studied glasses is La > Gd > Lu > Y, matching with RE 3+ polarizability. Furthermore, Ln 2 Te 6 O 15 nanocrystallite-embedded transparent GCs exhibit a larger NLO coefficient due to the enhanced local field from oxygen vacancies in crystallites. Interestingly, the trend of χ (3) in GCs follows the sequence of Y > Lu > Gd > La, precisely opposite to the glasses. This observation challenges the general polarizability approach of RE 3+ ions, emphasizing that quadratic hyperpolarizability of RE 3+ is pivotal for NLO properties of GCs. Among the studied matrices, Y-containing GCs showed the lowest optical limiting (OL) threshold (5.4 mJ/cm 2 at 800 nm), much lower than those of the reported NLO materials, suggesting its potential as a femtosecond NIR-laser safety material. A combination of large α 2 and n 2 from the studied matrices indicates their advantage for harmonic generation, potentially aiding in the design of ultrafast signal processing devices.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Engineering Thermally Resilient and Kinetically Active Reversible Protonic Ceramic Cells via Interfacial Design

Achieving concurrent fast electrode kinetics and long-term thermo-mechanical durability remains a critical challenge for reversible protonic ceramic electrochemical cells (R-PCECs). Herein, we report an interfacial engineering strategy that integrates a perovs.kite-type PrBaRu0.1Co1.9O5+δ (PBRC) nanoparticle layer onto a PrBa0.5Sr0.5Co1.5Fe0.5O5+δ (PBSCF) substrate (PBRC-PBSCF), together with a modified pellet-assisted sintering approach to fabricate dense BaZr0.4Ce0.4Y0.1Yb0.1O3-δ (BZCYYb4411) electrolytes. The in situ reconstructed heterointerface enhances oxygen reduction/evolution reaction (ORR/OER) kinetics, promotes H2O adsorption/dissociation, and improves steam tolerance, as verified by electrochemical measurements and interfacial microstructural analyses. Density functional theory reveals that Ru-induced electronic modulation at the PBRC-PBSCF interface lowers the energy of oxygen vacancy formation and optimizes the position of the O 2p band center, thereby accelerating oxygen redox kinetics and stabilizing the interface. The resulting R-PCECs deliver an excellent peak power density of 1.112 W cm−2 and an electrolysis current density of −1.257 A cm−2 at 1.3 V in 3% H2O wet air at 600°C, with a reasonable faradaic efficiency. Furthermore, the cells demonstrate excellent stability, sustaining 100 h of thermal cycling (400–600°C, 200°C h−1) in both fuel cell and electrolysis modes, with 600 h of stability in electrolysis mode (600°C, −0.5 to −2 A cm−2).

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2026

Enhanced Electrocatalytic and Cathode‐Electrolyte Interfacial Properties With a Pr‐Based Simple Perovskite/Ruddlesden‐Popper Nanocomposite Cathode in Protonic Ceramic Fuel Cells

The sluggish kinetics and poor stability of the oxygen reduction reaction (ORR) remain the primary bottleneck for achieving high performance in protonic ceramic fuel cells (PCFCs) at intermediate temperatures (400–650°C). In this work, a Pr-based nanocomposite cathode comprised of simple perovskite phase (PrNi 0.7 Co 0.3 O 3-δ ) and Ruddlesden-Popper phase (Co-doped Pr 4 Ni 3 O 10+δ ) is developed. Although PrNi 0.7 Co 0.3 O 3-δ solely stands as a good cathode with facile proton transfer, combining the superior catalytic activity against oxygen on the Ruddlesden-Popper phase boosts the ORR performance further. The designed nanocomposite cathode outperforms the simple perovskite cathode, attributed to enhanced oxygen absorption and surface diffusion with the Ruddlesden-Popper phase. A precursor-based cathode deposition technique is also developed to achieve cathode grain sizes of ∼100 nm. A single cell with the nanocomposite cathode delivers a peak power density of 1.38 W cm −2 at 650°C, among the highest in reported PCFCs with Pr-based cathodes, with a small degradation rate of 0.145 mV h −1 during 250 h stability test. Further investigation of cathode-electrolyte interface revealed interfacial PrO 2 phase formation, promoted by abundant Pr 6 O 11 in the nanocomposite precursor powder, thereby improving both ohmic resistance and stability. These findings highlight the effectiveness of the nanocomposite cathode and underscore its advantages on interfacial properties.

08 - HYDROGEN↗
DOE OSTI2024

Response of 11 B enriched ZrB 2 ultra-high temperature ceramic to neutron irradiation at elevated temperatures

ZrB 2 , an ultra-high temperature ceramic (UHTC) is being considered for use in fusion reactor first-wall structures, yet its response to irradiation remains poorly understood. This study employed scanning/transmission electron microscopy (S/TEM), synchrotron X-ray diffraction (XRD), finite element calculations, and thermal property measurements to thoroughly investigate the neutron-irradiation effects on 11 B-enriched ZrB 2 . Neutron irradiations were conducted at 220 °C and 620 °C, with a neutron fluence of 2.2 × 10 25 neutron/m 2 (energy > 0.1 MeV), resulting in 3.9 dpa and 4200 appm He. The study revealed the unusual prevalence of prism loops and a > c anisotropic lattice swelling, likely linked to the low c/a ratio of ZrB 2 , leading to grain boundary microcracking. Reducing the grain sizes was effective in reducing intergranular cracking and macroscopic swelling. The observation of cavities in ZrB 2 irradiated at 620 °C, as opposed to 220 °C, prompts questions about the temperature at which vacancies in ZrB 2 become mobile, and the role of neutron absorption by 10 B in elevating irradiation temperatures. Isotopic enrichment in 11 B proves to be a viable strategy for mitigating helium production in transition-metal diborides, which is a critical consideration for nuclear applications. Irradiation-induced defects reduce the thermal diffusivity and conductivity of ZrB 2 by a factor of 4–9, which has important implications for its role as a plasma-facing material in fusion reactors that drive high heat fluxes through first-wall materials. Here, this comprehensive study lays the foundation for understanding ZrB 2 behavior under neutron irradiation and highlights important phenomena to consider for various material applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Exsolution of NiCo alloys over Ruddlesden-Popper perovskite for mild electrochemical synthesis of ammonia on protonic ceramic electrochemical cells

Ammonia synthesis from renewable energies on protonic ceramic electrochemical cells (PCECs) shows great potential. The primary challenges in ammonia synthesis on PCECs include sluggish catalytic activity, competition from the hydrogen evolution reaction, and unsatisfactory durability of the cathode, which is the active site of ammonia generation. Here, in this study, we report an elaborate design of the cathode with an intended formula of Pr 4 Ni 1.79 Co 1.2R u 0.01 O 10-δ , where NiCo alloy nanoparticles are exsolved from Ruddlesden-Popper perovskite substrates after the reduction in 5 % H 2 /Ar at 400 °C for 1 h, for electrocatalysis of the nitrogen reduction reaction to ammonia. The host material Pr 4 Ni 1.8 Co 1.2 O 10-δ with embeddable layered structure and stability was deliberately chosen to fix the Ru cation and maximize the catalytic activity of NiCo. Also, density functional theory calculations suggest that Ru doping provides an optimal balance between structural stability and redox activity, facilitating the controlled exsolution of NiCo nanoparticles and enhancing catalytic performance. As a result, the composite electrode with exsolved NiCo alloy and abundant oxygen vacancies on fuel-electrode-supported PCECs achieves a superior electrochemical activity towards ammonia synthesis: a peak ammonia formation rate of 27.84 μg h −1 cm −2 and excellent Faradaic efficiencies of 62.6 % at 350 °C.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Heterostructured nano-catalysts with efficient metal-oxide interfaces unlock high-performance direct methanol protonic ceramic fuel cells

Direct methanol protonic ceramic fuel cells (PCFCs) are attractive due to their low cost, convenient storage, and high volumetric energy density, as well as their suitability for transportation. However, the poor coking tolerance of conventional nickel-based anodes leads to their susceptibility to severe carbon deposition and significant deactivation after long-term exposure to hydrocarbons. Herein, we report a nano-catalyst of Ce 0.6 Ni 0.2 Cu 0.2 O 2 with a heterogeneous structure that is spontaneously reduced into a Ce 0.6 Ni 0.2-x Cu 0.2-x O 2-δ (CeNCO) oxide framework interfaced with a nano NiCu alloy (denoted as NC/CeNCO) under operating conditions, as confirmed by analyses of X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy. A Ni-BaCe 0.7 Y 0.06 Yb 0.06 Zr 0.06 Hf 0.06 Gd 0.06 O 3-δ anode-supported PCFC employing the NC/CeNCO metal-oxide catalyst achieved a peak power density of 1.11 W cm −2 and operational stability of about 100 h at 700 °C when fueled by 35 % CH 3 OH-15 % H 2 O-50 % N 2 . In conclusion, the enhanced performance and coking resistance are attributed to the efficient interfaces of Ni, Cu, and ceria-based oxide in NC/CeNCO for CH 3 OH reforming, as confirmed by analyses of electrochemical performance and Raman spectroscopy with density functional theory calculations, revealing that these interfaces can enhance CH 3 OH activation and promote efficient OH-mediated carbon removal via COH intermediates.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Multi deep learning-based stochastic microstructure reconstruction and high-fidelity micromechanics simulation of time-dependent ceramic matrix composite response

A multi deep learning-based framework is developed for efficient, automated microstructure reconstruction and generation of stochastic representative volume elements (SRVEs) with periodic boundary conditions (PBCs) for accurate modeling of ceramic matrix composite (CMC) response. The methodology comprises a convolutional neural network coupled with regression layers to act as a vanilla regression network for semantic segmentation of the microstructure, allowing accurate characterization of the phases and their distributions at the microscale. Scanning electron microscope and confocal microscope are used to obtain C/SiNC and SiC/SiNC CMCs micrographs for vanilla regression testing. Microstructure variability in terms of fiber volume fraction and porosity are quantified through the output regression layer, ensuring accurate representation of material variability in SRVE construction. Generative adversarial network (GAN) and its variants are designed to produce high-fidelity SRVE, spanning CMCs microstructure variability space. A circular padding algorithm is developed to generate SRVEs with PBCs during training of GANs. The accuracy of the generated SRVEs is established through micromechanics simulations, where an efficient formulation of the high-fidelity generalized methods of cells (HFGMC) approach is used to compute the effective mechanical properties. Furthermore, an iterative algorithm is implemented in the HFGMC solver to simulate time-dependent deformation of SiC/SiNC subjected to creep loading conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A mean field homogenization model for the mechanical response of ceramic matrix composites

SiC/SiC composites offer exceptional mechanical stability at high temperatures and under irradiation. These ceramic matrix composites are therefore strong candidate materials for future nuclear energy applications. Their mechanical response, which exhibits pseudo-plasticity, is mediated by matrix cracking, fiber debonding, and fiber pull-out due to slip. Here, this study introduces a mechanistic model for the behavior of unidirectionally reinforced SiC/SiC composites. Specifically a mean field homogenization approach is proposed to account for all deformation and degradation modes during mechanical deformation. The homogenization scheme relies on a Mori Tanaka method that is extended to consider the effects of the coating’s elasto-plastic response on the development of micromechanical fields. Further, the model proposed introduces a method to effectively account for the role of localized damage (i.e., cracks) on mechanical fields within both the fiber and the matrix. Upon validating the model against experimental data, the roles of interface sliding, coating dimensions and intrinsic elastic response, as well as of microstructure (e.g. porosity, fiber volume fraction) are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗