Search NASA⌕ Search

SEARCH · Search NASA

Results for “Chromium doping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Optical, electrical, and EPR studies of polycrystalline Al:Cr:ZnSe gain elements

Transition metal-doped II-VI (TM:II-VI) chalcogenides are well-known laser materials for optically pumped middle-infrared lasers. Cr:ZnSe is a key representative of this class of transition metal doped II-VI gain media and is arguably considered the material of choice for optically pumped middle-infrared lasers. In addition to effective mid-IR lasing under optical excitation, these crystals, being wide-band semiconductors, hold the potential for direct electrical excitation. One way to form n-type conductivity in ZnSe crystals is by annealing them in a melt of Zn-Al alloy. However, this annealing of Cr:ZnSe crystals results in their purification and transfer of chromium to the melt of Zn-Al alloy. In this article, we report on optimizing the doping technique for providing n-type conductivity in Al:Cr:ZnSe crystals while preserving the chromium concentration. Al:Cr:ZnSe samples with resistivities ranging from 10.8 to 992 Ω-cm were fabricated. While the 2 + valence state of Cr is typically dominant in Cr:ZnSe, both Cr 2+ and Cr + were detected in Al:Cr:ZnSe samples. The maximum level of Cr + concentration was measured to be 4 × 10 18 cm -3 .

36 MATERIALS SCIENCE↗
NASA NTRS1966

Chromium oxide coatings improve thermal emissivity of alumina

Chromium oxide coatings improve thermal radiation characteristics of alumina-coated heater-cathode systems in vacuum tubes. Chromium oxide is applied either as a surface layer or as a doping material. The new coatings eliminate the high temperature migration problems of carbon surface treatments.

Upshaw, V.↗
DOE OSTI2021

In Situ Growth and Interlayer Modulation of Layered Double Hydroxide Thin Films from a Transparent Conducting Oxide Precursor

Layered double hydroxides (LDHs) are a class of cationic-layered solids that can be synthetically designed for a variety of advanced functions. Facile thin film growth of LDHs is an important requisite for a variety of applications including functional coatings, displays, and sensing. In this work we demonstrate, for the first time, an in-situ and patternable thin film synthesis of interconnected Zn-Cr LDH particles from a transparent conducting oxide (TCO) precursor, aluminum-doped zinc oxide (AZO), at room temperature within minutes. Synthetic parameters such as chromium (III) nitrate concentration, solvent composition, and reaction time were found to significantly affect the thickness and morphology of the resulting LDH films. These LDH thin films can undergo interlayer anion exchange, which modulates the interlayer distance of the LDH sheets and surface energy of the thin film. Replacement of the interlayer anion with perfluorooctanoate increases the interlayer sheet distance from 0.9 nm to 2.8 nm and induces a super-hydrophobic thin film that is capable of adsolubilizing and retaining organic guest molecules. The synthetic method and structural analysis of the LDH thin films introduced in this work opens new avenues of application for LDH films.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1993

Chromium and reactive element modified aluminide diffusion coatings on superalloys - Environmental testing

The high temperature performance of reactive element (RE)-doped and Cr/RE-modified aluminide diffusion coatings on commercial Ni-base alloy substrates was determined. In isothermal oxidation at 1100 C in air, RE-doped aluminide coatings on IN 713LC substrates formed a continuous slow-growing n-Al2O3 scale after 44 hrs of exposure. The coatings were protected by either an outer ridge Al2O3 scale with an inner compact Al2O3 scale rich in RE or by a continuous compact scale without any noticeable cracks or flaws. The cyclic oxidation behavior of Cr/RE-modified aluminide coatings on Rene 80 and IN 713LC alloys and of RE-doped aluminide coatings on IN 713LC alloys at 1100 C in static air was determined. Pack powder entrapment from the powder contacting (PC) process detracted significantly from the overall cyclic oxidation performance. Type I hot corrosion behavior of Cr/RE-modified aluminide coatings on Rene 80 and Mar-M247 alloy substrates at 900 C in a catalyzed 0.1 percent SO3/O3 gas mixture was determined. The modified coatings produced from the PC arrangement provided significantly better resistance to hot corrosion attack than commercial low-activity aluminide coatings produced by the above pack arrangement.

Bianco, Robert↗
DOE OSTI2024

Development of Stable Solid Oxide Electrolysis Cells for Low-Cost Hydrogen Production

The project objective was to demonstrate a solid oxide cell-based steam electrolysis stack that exhibits robustness, reliability, endurance, hydrogen purity, and produces hydrogen at elevated pressure of 2 to 3 bar. Innovative materials and processing methods were evaluated to improve degradation characteristics. Performance improvement focused on nearly all layers involved in the cell and stack assembly. Primary attention was paid to zirconia-ceria interface resistance control via sintering optimization and decrease in degradation from the oxygen electrode by evaluating low strontium (Sr) or Sr-free composition for both the oxygen electrode and current collection layer. Stack robustness was addressed by validating redox tolerance of fuel electrode, confirming capability of cells to survive repeated thermal cycles, studying the effect of pressure on performance and degradation, evaluating the effect of contamination on fuel and oxygen electrode performance and degradation, and identifying mitigation strategies to improve performance. The characterization included evaluation of electrochemical performance and stability followed by microstructural analysis. At the cell level, performance and stability improvements were achieved by incorporating a Sr-free oxygen electrode and a denser oxygen electrode barrier layer. At the stack level, pressurized operation reduces demand on first stage compression, the redox tolerant fuel electrode mitigates risk from service interruptions, and improvements to interconnect coating alleviate chromium (Cr) contamination effects. The denser barrier layer was achieved by adding a sintering aid to the samaria-doped ceria (SDC) composition that reduced sintering temperature by 150 °C. The resulting density was on par with the baseline SDC barrier layer density and the lower sintering temperature resulted in less resistive phase formation during sintering. Button cell tests did not demonstrate a change in performance when exposed to silicon (Si) or manganese (Mn) impurities to the fuel electrode and Cr impurity to the oxygen electrode. More detailed study however is warranted. The project addressed SOEC performance and stability at the cell and stack levels through a systematic approach to known sources of degradation that were combined and tested in three stack tests using an electrolyte supported cell design to allow for evaluation of a variety of fuel and oxygen electrode compositions. STK-82 and STK-83 had identical compositions. STK-100 incorporated the best materials and processing variables developed under this and concurrent projects, and was tested at elevated pressure in steam electrolysis. • STK-82 recovered performance after redox and thermal cycling, demonstrating the robustness of the stack and seals. It exhibited stable performance in testing for 500 hours in SOEC mode, followed by 300 hours of cycling between SOEC and SOFC tests. Degradation during SOEC operation was 1.8 %/ 1,000 hours. • STK-83 generated hydrogen at >80% steam conversion, and oxygen above 98.5 % purity during pressurized operation. Both hydrogen and oxygen were generated at 3 barg pressure without the use of a pressure vessel. In addition to balanced pressure, electrolysis operation at 1 bar differential pressure across anode and cathode was also demonstrated to substantial the robustness of the cell and seal. • STK-100 measured at initial ambient pressure conditions showed an area specific resistance of 1.1 ohm-cm 2 , and STK-83 had 1.3 ohm-cm 2 .

08 HYDROGEN↗
DOE OSTI2020

Fabrication of stable electrode/diffusion barrier layers for thermoelectric filled skutterudite devices

Disclosed are methods for the manufacture of n-type and p-type filled skutterudite thermoelectric legs of an electrical contact. A first material of CoSi2 and a dopant are ball-milled to form a first powder which is thermo-mechanically processed with a second powder of n-type skutterudite to form a n-type skutterudite layer disposed between a first layer and a third layer of the doped-CoSi2. In addition, a plurality of components such as iron, and nickel, and at least one of cobalt or chromium are ball-milled form a first powder that is thermo-mechanically processed with a p-type skutterudite layer to form a p-type skutterudite layer “second layer” disposed between a first and a third layer of the first powder. The specific contact resistance between the first layer and the skutterudite layer for both the n-type and the p-type skutterudites subsequent to hot-pressing is less than about 10.0 μΩ·cm2.

Jie, Qing↗
DOE OSTI2025

Demonstrate new plasticity models for doped UO 2 that capture dislocation mechanisms

In light water reactors, fuel vendors are investigating the use of dopants to modify the properties of UO 2 pellets, with the goal of improving pellet-cladding mechanical interactions during operation. Dopants are expected to ‘soften’ the pellets; that is, the doped pellets have higher plastic deformation than conventional UO 2 . This leads to a reduction in the severity of mechanical pellet-cladding interactions, helping to reduce the hoop strain on the cladding. By minimizing the strain exerted by the pellet on the cladding, it is anticipated that cladding performance under accident conditions can be enhanced (i.e., lowering the risk of burst during a LOCA). Dopants such as chromium (Cr) promote grain growth during pellet fabrication, leading to larger grains; therefore, understanding the link between chemistry, microstructure and mechanical deformation (enhanced creep rates) behavior of UO 2 is critical to helping operators further substantiate the benefits of doping UO 2 . Historically, the nuclear energy industry has relied on empirical models to make assessments of performance. Compared to empirical models, mechanistic physics-based models provide benefits, such as, fewer data points for validation and better extrapolation where experimental data is scarce or non-existent. In this report, Bayesian inference techniques have been applied to a previously developed lower length-scale-informed diffusional creep model. The objective is to i) infer lower-length-scale parameter distributions from available experiment and then ii) determine the uncertainties in the measurable quantity (in this case creep rates) after propagating the inferred lower length scale parameter uncertainties. The approach requires many evaluations of the model, which becomes computationally insurmountable; therefore, a neural-network model is trained to data obtained by sampling the full model over the most important parameters. This neural-network is then used in the Bayesian inference approach to determine probability distributions in the parameter values that represent the uncertainty in the model given what is known from the experiments (posterior). A significant reduction compared to conservative initial (prior) uncertainties is achieved through inference against the experimental data, demonstrating the efficacy of this approach. Furthermore, by accounting for uncertainties in the experimental conditions and sample non-stoichiometry, it is possible to resolve apparent discrepancies in experimental measurements within a self-consistent grain boundary (Coble) creep model that is sensitive to chemistry. This work has been written up and submitted to Nuclear Technology for a special issue on accelerated fuel qualification (AFQ). This uncertainty quantification (UQ) work not only improves the diffusional model, while accounting for uncertainty, but also establishes a framework which can readily be applied to the mechanistic models of dislocation deformation developed in this study. The most likely values from the Bayesian analysis are incorporated into our UO 2 diffusional creep model and a lower length scale-informed irradiation UO 2 creep mechanistic model to generate a dataset. This dataset has been provided to our INL collaborators for training an artificial neural network surrogate model, which will be implemented in the BISON fuel performance code to assess how the results differ from those currently obtained using a fully empirical model and that of using the nominal (uncalibrated) atomic scale parameters in our mechanistic model. Plastic deformation (creep and glide) in UO 2 is a complex phenomenon, governed by multiple underlying processes such as local defect concentrations, applied stresses, and microstructural characteristics. Consequently, there is a need for a meso-scale model with polycrystalline resolution capable of extrapolating to large grain sizes applicable to doped UO 2 , where data is limited and the model can help bridge the knowledge gap. By integrating atomistic data into the polycrystal LApx code, it becomes possible to predict dislocation climb and glide plasticity that simple analytical models cannot accurately represent. The application of atomic-scale data within LApx demonstrated the importance of climb and glide mechanisms in reproducing high-stress UO 2 behavior. Behaviors such as this are crucial to capture and implement in BISON, as parts of the fuel pellet can reach temperatures where glide can occur before pellet cracking. This model which captures dislocation based mechanisms for UO 2 is then used to stand up the doped model accounting for larger grain sizes. It was found that larger grain sizes can lead to enhanced deformation rates in the glide regime, and therefore can help with the pellet cladding mechanical interaction. Therefore if the fuel pellet reaches conditions (stress/temperature) where glide is active, the enhanced creep rates for larger grains in the glide regime (doped UO 2 ) can help with pellet cladding mechanical interactions. Plastic deformation in UO 2 involves multiple mechanisms, including diffusional creep, dislocation climb, and glide. This milestone contains two parts: (1) UQ of a pre-existing lower length scale informed mechanistic diffusional creep model, and (2) development of a new LApx based model for dislocation-mediated creep mechanisms in UO 2 , with application to large-grain doped UO 2 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Synthesis of Samarium Nitride Thin Films on Magnesium Oxide (001) Substrates Using Molecular Beam Epitaxy

Rare-earth nitrides are an exciting family of materials with a wide variety of properties desirable for new physics and applications in spintronics and superconducting devices. Among them, samarium nitride is an interesting compound reported to have ferromagnetic behavior coupled with the potential existence of p-wave superconductivity. Synthesis of high-quality thin films is essential in order to manifest these behaviors and understand the impact that vacancies, structural distortions, and doping can have on these properties. In this study, we report the synthesis of samarium nitride monocrystalline thin films on magnesium oxide (001) substrates with a chromium nitride capping layer using molecular beam epitaxy (MBE). We observed a high-quality monocrystalline SmN film with matching orientation to the substrate, then optimized the growth temperature. Despite the initial 2 nm of growth showing formation of a potential samarium oxide layer, the subsequent layers showed high-quality SmN, with semiconducting behavior revealed by an increase in resistivity with decreasing temperature. These promising results highlight the importance of studying diverse heteroepitaxial schemes and open the door for integration of rare-earth nitrides and transition metal nitrides for future spintronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Gate-Tunable Proximity Effects in Graphene on Layered Magnetic Insulators

The extreme versatility of van der Waals materials derives from their ability to exhibit new electronic properties when assembled in proximity with dissimilar crystals. 1 For example, although graphene is inherently non-magnetic, recent work has reported a magnetic proximity effect in graphene interfaced with magnetic substrates, potentially enabling a pathway towards achieving a high-temperature quantum anomalous Hall effect. Here, we investigate heterostructures of graphene and chromium trihalide magnetic insulators (CrI 3 , CrBr 3 , and CrCl 3 ). Surprisingly, we are unable to detect a magnetic exchange field in the graphene, but instead discover proximity effects featuring unprecedented gate-tunability. The graphene becomes highly hole-doped due to charge transfer from the neighboring magnetic insulator, and further exhibits a variety of atypical gate-dependent transport features. The charge transfer can additionally be altered upon switching the magnetic states of the nearest CrI 3 layers. In conclusion, our results provide a roadmap for exploiting proximity effects arising in graphene coupled to magnetic insulators.

2D magnet↗
DOE OSTI2025

Property Measurements of LiF-NaF-KF Molten Salts Doped with Corrosion Products and Oxygen

Measurements of thermophysical properties of molten salts are needed for modeling and simulation activities that support the development of molten salt reactor (MSR) technologies. Properties of interest including transition temperatures, phase behavior, heat capacity, density, volumetric thermal expansion, surface tension, viscosity, thermal diffusivity, thermal conductivity, and vapor pressure are being performed at Argonne. Results of these property measurements are suitable for use in evaluating reactor performance during startup and the early operating life of the reactor. Ingressions of oxygen and moisture into the fuel salt are expected to occur at different times during the operating life of the reactor due to system leaks, maintenance, and refueling activities. The presence of these environmental contaminants induces corrosion of structural materials. The introduction of corrosion-derived species, oxygen and moisture is expected to affect the physical and chemical properties of the salt and operation of the reactor. Previous work performed at Argonne evaluated the effects of fission product dopants on the thermal properties of eutectic LiF-NaF-KF (FLiNaK). Properties of FLiNaK are commonly used to represent those of fluoride-bearing fuel salts. Metallic corrosion products such as chromium and nickel ions together with dissolved oxygen are expected to affect system redox differently than the accumulation of fission products. Work summarized in this report was performed to measure the effects of corrosion products and dissolved oxygen on the phase transitions, and specific heat capacity of FLiNaK. Thermophysical property measurements were made using four salts that were prepared by doping aliquots of a eutectic mixture of FLiNaK with surrogate corrosion products. Controlled additions of CrF 3 and NiF 2 were used as surrogates for corrosion product contamination anticipated during extended reactor operations in which fuel salt is in contact with steel reactor components. Controlled additions of UF 4 from two sources containing known amounts of UO 2 at different concentrations were used to represent oxygen contamination. The phase transitions and specific heat capacities of the four salts were measured by using differential scanning calorimetry. Measurements were made at temperatures spanning the range of 500−900 °C, which is the expected operating range of MSRs. Measured property values were compared to values measured previously with eutectic FLiNaK without dopants. Differences between property values measured for the doped and non-doped salts were compared with the uncertainties of the measurements to determine the significance of the effect of corrosion products and oxygen on salt properties.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1980

Evaluation of the hot corrosion behavior of thermal barrier coatings

Calcium silicate and yttria-stabilized ZrO2/(M-Cr-Al-Y) thermal barrier coating systems on air-cooled specimens were exposed to sodium- plus vanadium-doped Mach 0.3 combustion gases. The thermal barrier coating endurance was determined to be a strong inverse function of the ceramic coating thickness. Coating system durability was increased through the use of Ni-Cr-Al-Y and Co-Cr-Al-Y bond coatings with high chromium and aluminum contents. Chemical and electron microprobe analyses supported the predictions of condensate compositions and the determination of their roles in causing spalling of the ceramic coatings.

Hodge, P. E.↗
NASA NTRS1993

Reduced chromium in olivine grains from lunar basalt 15555 - X-ray Absorption Near Edge Structure (XANES)

The oxidation state of Cr in 200-micron regions within individual lunar olivine and pyroxene grains from lunar basalt 15555 was inferred using X-ray Absorption Near Edge Structure (XANES). Reference materials had previously been studied by optical absorption spectroscopy and included Cr-bearing borosilicate glasses synthesized under controlled oxygen fugacity and Cr-doped olivines. The energy dependence of XANES spectral features defined by these reference materials indicated that Cr is predominantly divalent in the lunar olivine and trivalent in the pyroxene. These results, coupled with the apparent f(02)-independence of partitioning coefficients for Cr into olivine, imply that the source magma was dominated by divalent Cr at the time of olivine crystallization.

Sutton, S. R.↗
NASA NTRS1998

Fluorescence of Pentavalent Chromium in SiO2 Sol-Gel Glasses

Chromium ions are very attractive to optical spectroscopy and laser physics. It is well known that the first laser in the history is a ruby laser activated with Cr(3+). It was found in early nineties that Cr(4+) was also an interesting lasing ion in the near infrared, and various Cr(4+) lasers have been developed. Very recently, it was reported that Cr(2+) doped in CdSe crystals showed lasing action in the infrared. The above achievement have stimulated an interest in searching for Cr(5+) and investigating its optical properties. Cr(5+) is isoelectronic with Ti(3+) and V(4+), having electron configuration 3d1. Ti(3+) is the active center of commercial cw and femtosecond sapphire lasers, tunable in the range 680-1100 nm. V(4+) doped in YAlO3 and Al2O3 showed broad band emission near 635 nm. Although EPR results of Cr(5+) were reported, the optical properties were less studied. Herren et al. reported an observation of luminescence from Cr doped in SiO2 sol-gel glass. The luminescence spectrum was assigned to pentavalent ions in their first paper, and later it was identified to be the emission from the charge transfer transition of Cr(6+). The first observation of photoluminescence from octahedrally coordinated Cr(5+) in BaCaMg aluminate glasses was reported very recently. In this work, we report luminescence results of Cr doped SiO2 sol-gel glasses. The fluorescence spectra are very different from Herrens' results, and we believe it originates from pentavalent Cr.

Jia, Weiyi↗
DOE OSTI2020

Observation of site-controlled localized charged excitons in CrI3/WSe2 heterostructures

Abstract Isolated spins are the focus of intense scientific exploration due to their potential role as qubits for quantum information science. Optical access to single spins, demonstrated in III-V semiconducting quantum dots, has fueled research aimed at realizing quantum networks. More recently, quantum emitters in atomically thin materials such as tungsten diselenide have been demonstrated to host optically addressable single spins by means of electrostatic doping the localized excitons. Electrostatic doping is not the only route to charging localized quantum emitters and another path forward is through band structure engineering using van der Waals heterojunctions. Critical to this second approach is to interface tungsten diselenide with other van der Waals materials with relative band-alignments conducive to the phenomenon of charge transfer. In this work we show that the Type-II band-alignment between tungsten diselenide and chromium triiodide can be exploited to excite localized charged excitons in tungsten diselenide. Leveraging spin-dependent charge transfer in the device, we demonstrate spin selectivity in the preparation of the spin-valley state of localized single holes. Combined with the use of strain-inducing nanopillars to coordinate the spatial location of tungsten diselenide quantum emitters, we uncover the possibility of realizing large-scale deterministic arrays of optically addressable spin-valley holes in a solid state platform.

42 ENGINEERING↗
DOE OSTI2020

Cobalt ferrite nanoparticle intercalated carbon nanotubes for a nanomagnetic ultrasensitive sensor of Cr-VI in water

Nanocomposites of cobalt ferrite (CFO) magnetic nanoparticles intercalated on carbon nanotubes (CNTs) are evaluated as a nanomagnetic ultrasensitive sensor for the environmental toxin, hexavalent chromium (Cr-VI). Specifically, the structural and magnetic changes that accompany the infiltration of the CFO/CNTs by Cr-VI are presented. Extended x-ray absorption fine structure (EXAFS) shows that the atomic spacing within the CFO structure changes in the presence of Cr, suggesting that the Cr is incorporated into the nanoparticles. Vibrating sample magnetometry (VSM) reveals that CFO/CNTs composite infiltrated with Cr-VI have a 71% enhancement in saturation magnetization compared with the uninfiltrated CFO/CNTs, while small-angle neutron scattering (SANS) suggests that this magnetic enhancement is not associated with the nanoparticle lengthscales, but may arise from longer-ranged clusters. Both VSM and SANS clearly demonstrate that the Cr-doped CFO/CNTs are hysteretic with a net magnetization at remanence that is about 1/3 that of saturation, while this hysteresis is absent in the undoped CFO/CNTs. These magnetic differences at either remanence or saturation are promising for the magnetic detection of Cr-VI using CFO/CNTs sensors.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Development of flashlamp-pumped Q-switched Ho:Tm:Cr:YAG lasers for mid-infrared LIDAR application

A flashlamp-pumped 2.1 micron Ho:Tm:Cr:YAG laser was studied for both normal mode and Q-switched operations under a wide variety of experimental conditions in order to optimize performance. Laser output energy, slope efficiency, threshold and pulselength were determined as a function of operating temperature, output mirror reflectivity, input electrical energy and Q-switch opening time. The measured normal-mode laser thresholds of a Ho(3+) (0.45 atomic percent):Tm(3+) (2.5 atomic percent):Cr(3+) (0.8 atomic percent):YAG crystal ranged form 26 to 50 J between 120 and 200 K with slope efficiencies up to 0.36 percent with a 60 percent reflective output mirror. Under Q-switched operation the slope efficiency was 90 percent of the normal-mode result. Development of solid state lasers with Ho(3+), Tm(3+) and/or Er(3+) doped crystals has been pursued by NASA for eye-dafe mid-infrared LIDAR (light detection and ranging) application. As a part of the project, the authors have been working on evaluating Ho(3+):Tm(3+):Cr(3+):YAG crystals for normal-mode and Q-switched 2.1 micron laser operations in order to determine an optimum Tm(3+) concentration under flashlamp pumping conditions. Lasing properties of the Ho(3+) in the mid-infrared region have been studied by many research groups since the early 1960's. However, the technology of those lasers is still premature for lidar application. In order to overcome the inefficiency related to narrow absorption bands of the Ho(3+), Tm(3+) and Er(3+), the erbium has been replaced by chromium. The improvement in flashlamp-pumped Ho(3+) laser efficiency has been demonstrated recently by several research groups by utilizing the broad absorption spectrum of Cr(3+) which covers the flashlamp's emission spectrum. Efficient energy transfer to the Tm(3+) and then the Ho(3+) occurs subsequently. It is known that high Tm(3+) concentration and low Ho(3+) concentration are preferred to achieve a quantum efficiency approaching two and to avoid large reabsorption losses. However, determination of the optimum Tm(3+) concentration required to ensure efficient energy transfer from Cr(3+) to Tm(3+) and from Tm(3+) to Ho(3+) has not been made in the Ho:Tm:CR:YAG crystal. The results obtained so far are given.

Choi, Young S.↗
DOE OSTI2023

Chromium Tolerant, Highly Active and Stable Electrocatalytic Internal Surface Coating for Cathode of Commercial SOFCs (Final Report)

This project is aimed to develop a chromium (Cr) tolerant, highly active, and stable coating layer on the internal surfaces of the porous composite cathode from commercially available SOFCs. Such coating layer was developed using the additive manufacturing process of Atomic Layer Deposition (ALD) and has been applied on the cathode consisting of either an electronic conductor of LaxSr 1-x MnyO 3-δ (LSM) or mixed ionic and electronic conducting La x Sr 1-x Co y Fe 1-y O 3-δ (LSCF). PI's work has demonstrated that the internal surface of cathode from the commercial cells, can be further tailored using ALD coating to dramatically enhance the cell performance. For instance, ALD layer consisting heterostructured nano composite of nano-Pt and nano-(Mn 0.8 Co 0.2 ) 3 O 4 oxide on the internal surface of porous LSM/YSZ cathode from SOFCs, has resulted in the large reduction of the cell polarizations resistance by up to 53%, and enormous increase of power density over 370%. For the cells with LSCF/Sm 2 O 3 doped CeO 2 (SDC) cathode, the conformal layer of nano-composite consisting of superjacent CoOx and subjacent minimum amount of Pt nano-grains has resulted in the power density enhancement by 126% for the large scale industry tubular cells at 750°C, and both the performance enhancement and nanostructure of the ALD layer are stable over ~ 2000 h continuous operation performed at industry test station. In the meanwhile, those ALD coating layer developed by PI's work is also inherently Cr-tolerant, and could act as physical barrier for preventing Cr diffusion into the cathode backbone, so as to mitigate the Cr poisoning effect on the cathode. In this project, the impact of Cr on the performance of those ALD coated commercial cells has been evaluated. Based on evolution of the cell performance, the ALD coating layer chemistry and ALD coating layer thickness has been optimized to maximize the overall Cr tolerance, cell power density and cell longevity. Different ALD coating has been applied onto the internal surface of LSM/YSZ and LSCF/SDC backbone respectively. The architecture/scaffold structures on the internal surface of different cathode, designed by this project, was catalogued and analyzed using High Resolution Transmission Electron Microscopy (HRTEM), and cell power/durability performance are assured via comprehensive electrochemical performance testing in the industry operation relevant conditions. The impact of the electrochemical operation current density, the water humidity, the cell operation temperature, and cell operation duration on the Cr tolerance of ALD coated cells has been systematically investigated. There is completely different nanostructure degradation mechanisms between LSM and LSCF cells induced by Cr contamination. For the LSCF/SDC baseline cell, With the Cr source, there is no apparent Sr surface segregation phase even for the baseline cell operated for 3000 h at 750 °C. With the Cr source, there is significant amorphous (SrCr)Ox phase accumulated in the original pore region. For the commercial baseline cells, Cr contaminants on the LSM electrode severely impacted the entire cell's electrochemical performance and nanostructure degradation. Those degradations include (1). Peak power density loss of 64 % after 109 h of operation. The dramatic increase in Rp (2). They are cracking at LSM/SSZ interface, LSM grains. SSZ remains intact but with (CrMn)Ox. By contrast, ALD coating (MnCo)Ox/Pt dramatically improves the Cr resistance, as follows (1). ALD-coated cell with a power density is 280-380 % of the baseline cell, depending on the ALD layer thickness. (2). For a cell with a 20 nm thick ALD layer, there is a large performance enhancement (> 200 % power density) induced by ALD coating of Cr-tolerant Mn 0.8 Co 0.2 Ox. (3). For a cell with a 20 nm thick ALD layer, after 168 h at 750 °C power density of the ALD-coated cell is ~ 600% of that baseline cell upon operation with Cr contamination for 109 h. The ALD coating on the internal surface of cathode developed by this project integrated multi-functions. Those multi-functions include (1). Dramatically improving the cell power density for the commercial cells; (2). Dramatically improving contamination resistance of the cathode, for being an excellent protection coating layer sealing off Cr contamination. (3). Dramatically increasing the cell longevity by potentially preventing the microstructure evolution and grain coarsening of the cathode. Overall, this project will provide a simple solution to simultaneously enhance power density and increase the reliability, robustness, and endurance of commercial SOFCs, over the entire operating temperature range of 650-800 °C. For the inherently functional SOFC, the ALD coating of LSM based cathode mitigate the Cr-contamination. Power density of ALD-coated cell is ~ 600% of that baseline cell upon operation with Cr contamination. In addition to SOFCs, the novel on-demand design approach and creation of multifunctional heterogeneous architecture on the electrode surface presented in this work opens further research for their application in other types of fuel cells, batteries, and sensors for which electrochemical reactions on the surface are similarly critical.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Coprecipitation of Fe/Cr Hydroxides at Organic–Water Interfaces: Functional Group Richness and (De)protonation Control Amounts and Compositions of Coprecipitates

Iron/chromium hydroxide coprecipitation controls the fate and transport of toxic chromium (Cr) in many natural and engineered systems. Organic coatings on soil and engineered surfaces are ubiquitous; however, mechanistic controls of these organic coatings over Fe/Cr hydroxide coprecipitation are poorly understood. Here, Fe/Cr hydroxide coprecipitation was conducted on model organic coatings of humic acid (HA), sodium alginate (SA), and bovine serum albumin (BSA). The organics bonded with SiO 2 through ligand exchange with carboxyl (-COOH), and the adsorbed amounts and pK(a) values of -COOH controlled surface charges of coatings. The adsorbed organic films also had different complexation capacities with Fe/Cr ions and Fe/Cr hydroxide particles, resulting in significant differences in both the amount (on HA > SA(-COOH) >> BSA(-NH 2 )) and composition (Cr/Fe molar ratio: on BSA(-NH2) >> HA > SA(-COOH)) of heterogeneous precipitates. Negatively charged -COOH attracted more Fe ions and oligomers of hydrolyzed Fe/Cr species and subsequently promoted heterogeneous precipitation of Fe/Cr hydroxide nanoparticles. Organic coatings containing -NH 2 were positively charged at acidic pH because of the high pK(a) value of the functional group, limiting cation adsorption and formation of coprecipitates. Meanwhile, the higher local pH near the -NH 2 coatings promoted the formation of Cr(OH) 3 . Finally, this study advances fundamental understanding of heterogeneous Fe/Cr hydroxide coprecipitation on organics, which is essential for successful Cr remediation and removal in both natural and engineered settings, as well as the synthesis of Cr-doped iron (oxy)hydroxides for material applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗