Search NASA⌕ Search

SEARCH · Search NASA

Results for “Composition B”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Detonation Soot: A New Class of Ice Nucleating Particle

Abstract Temperatures and pressures from high explosive detonations far exceed atmospheric conditions in typical combustion reactions, and consequently, detonation soot forms with physiochemical properties distinct from soot formed by combustion. In this study, samples of detonation soot from two high explosives, PBX 9502 and Composition B‐3, were analyzed. Ice nucleation experiments on soot collected after controlled detonations were conducted in the laboratory to probe immersion and contact mode freezing. Samples nucleated ice at temperatures warmer than commercially available nanodiamonds, which has a mean nucleation temperature of −20.7°C. Ice nucleation rate coefficients increase rapidly by two to three orders of magnitude below −20°C for every sample. Size‐selected 137 μm diameter particles produced during detonation in an ambient air atmosphere yield bimodal distributions of freezing temperature with primary and secondary nucleation modes centered at −20°C and −13°C, respectively. The presence of a secondary mode allows for enhanced ice nucleation rate coefficients (one to two orders of magnitude greater than samples without a secondary mode) at temperatures outside the influence of the primary mode (>−17°C). Given the observed onset nucleation temperatures of −9.2°C, our results imply that detonation soot of the type studied here would only need to reach an altitude of approximately 4 km to facilitate ice formation.

54 ENVIRONMENTAL SCIENCES↗

DEFLAGRATION RATES OF SECONDARY EXPLOSIVES UNDER STATIC MPA - GPA PRESSURE

We provide measurements of the chemical reaction propagation rate (RPR) as a function of pressure using diamond anvil cell (DAC) and strand burner technologies. Materials investigated include HMX and RDX crystalline powders, LX-04 (85% HMX and 15% Viton A), and Composition B (63% RDX, 36% TNT, 1% wax). The anomalous correspondence between crystal structure, including in some instances isostructural phase transitions, on pressure dependent RPRs of HMX and RDX are correlated to confocal micro-Raman spectroscopic results. The contrast between DAC GPa and strand burner MPa regime measurements yield insight into explosive material burn phenomena. Here we highlight pressure dependent physicochemical mechanisms that appear to affect the deflagration rate of precompressed energetic materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The role of Mg interface layer in MgO magnetic tunnel junctions with CoFe and CoFeB electrodes

The tunneling spin polarization (TSP) is directly measured from reactively sputter deposited crystalline MgO tunnel barriers with various CoFe(B) compositions using superconducting tunneling spectroscopy. We find that the Mg interface layer thickness dependence of TSP values for CoFeB/Mg/MgO junctions is substantially different from those for CoFe/Mg/MgO especially in the pre-annealed samples due to the formation of boron oxide at the CoFeB/MgO interface. Annealing depletes boron at the interface thus requiring a finite Mg interface layer to prevent CoFeOx formation at the CoFeB/MgO interface so that the TSP values can be optimized by controlling Mg thickness.

36 MATERIALS SCIENCE↗

Short communication: Estimation of yield stress/viscosity of molten octol

Explosive HMX particles are similar in morphology and chemistry to RDX particles, the main constituent of Composition B-3 (Comp B-3). This suggests molten HMX-TNT formulations may show Bingham plasticity, much like recent studies have shown for Comp B-3. Here a Bingham plastic viscosity model, including yield stress and shear thinning, is presented for octol (70/30wt% HMX/TNT) as a function of HMX particle volume fraction. The effect of HMX dissolution into molten TNT is included in this analysis.

36 MATERIALS SCIENCE↗

Theoretical prediction of a highly responsive material: Spin fluctuations and superconductivity in FeNiB 2 system

By analyzing the Fe-Ni-B compositional diagram, we predict an energetically and dynamically stable FeNiB 2 compound. This system belongs to the class of highly responsive state of materials, as it is very sensitive to the external perturbations. This state is also characterized by a high level of spin fluctuations, which strongly influence possible magnetic long- and short-range orders. Furthermore, we demonstrate that these antiferromagnetically dominating fluctuations could lead to the appearance of spin mediated superconductivity. The obtained results suggest a promising avenue for the search of strong spin fluctuation systems and related superconductors. Spin fluctuations (SFs) in itinerant electron magnets play an important role in many metallic systems including weak itinerant magnets, heavy fermion compounds, actinides, Invar alloys, and many magnetoresistive materials. SFs also have been identified in high-temperature superconductors and recently discovered Fe-based superconductors with a clear suggestion about their crucial influence on the mechanisms of unconventional superconductivity. In the majority of cases, superconductivity appears near the magnetic quantum critical point, where magnetism has a pure itinerant character with no local moments involved. This is exactly a case when quantum SFs (including spin zero-point motion) are strong and provide a dominating contribution to many observable physical properties. However, as a typical example, in a case of superconductivity, the direct calculations and prediction of critical temperature from first principles are still not possible. In this situation, one can focus on searching for materials with a strong level of SF, leading to the possible development of promising physical properties. In this paper, we will introduce qualitatively the concept of a highly responsive state (HRS) (see Fig. 1). This term is used here to indicate that a physical system is in a state characterized by an order parameter, which is very sensitive to the external perturbations (pressure, magnetic fields, etc.). The HRS is naturally related to closeness to the instability and, as usual in such situations, one can expect that fluctuations are very important.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Equation of state measurement of detonation carbon condensates using optical microscopy and interferometry

Thermochemical models of detonation that estimate performance (e.g., detonation velocity, energy delivery, etc.), are based on assumptions that carbon condensates (soot) formed during detonation is largely similar to bulk carbon. However, soot constituents can range from amorphous carbon to nanodiamond and include other material phases. Since thermodynamic properties of the soot such as compressibility are imperative for accurate thermochemical modeling of detonation reaction chemistry, experimental measurements of the equation of state (EOS) which determine the compressibility are vital. Due to the mixed-phase nature of detonation soot, typical methods to measure the EOS (e.g., x-ray diffraction) are untenable. In this study, the high-pressure EOS up to 20 GPa was determined for detonation soot collected from PBX 9502, Composition B (Comp B), Hexanitrostilbene (HNS), and LX-21 high explosives by employing a direct volume technique using optical microscopy and interferometry in a diamond anvil cell. Comp B soot was determined to be the least compressible [K 0 = 57.9(17) GPa] with HNS soot [K 0 = 53.7(15) GPa], LX-21 soot [K 0 = 45.8(51) GPa], and PBX 9502 soot [K 0 = 28.2(27) GPa] being more compressible, likely due to differences in nanodiamond content as compared to amorphous carbon and graphite content.

Amorphous materials↗

The role of Dark Matter sub-halos in the non-thermal emission of galaxy clusters

Annihilation of Dark Matter (DM) particles has been recognized as one of the possible mechanisms for the production of non-thermal particles and radiation in galaxy clusters. Previous studies have shown that, while DM models can reproduce the spectral properties of the radio halo in the Coma cluster, they fail in reproducing the shape of the radio halo surface brightness because they produce a shape that is too concentrated towards the center of the cluster with respect to the observed one. However, in previous studies the DM distribution was modeled as a single spherically symmetric halo, while the DM distribution in Coma is found to have a complex and elongated shape. In this work we calculate a range of non-thermal emissions in the Coma cluster by using the observed distribution of DM sub-halos. We find that, by including the observed sub-halos in the DM model, we obtain a radio surface brightness with a shape similar to the observed one, and that the sub-halos boost the radio emission by a factor between 5 and 20%, thus allowing to reduce the gap between the annihilation cross section required to reproduce the radio halo flux and the upper limits derived from other observations, and that this gap can be explained by realistic values of the boosting factor due to smaller substructures. Models with neutralino mass of 9 GeV and composition τ{sup +} τ{sup −}, and mass of 43 GeV and composition b b-bar can fit the radio halo spectrum using the observed properties of the magnetic field in Coma, and do not predict a gamma-ray emission in excess compared to the recent Fermi-LAT upper limits. These findings make these DM models viable candidate to explain the origin of radio halos in galaxy clusters, avoiding the problems connected to the excessive gamma-ray emission expected from proton acceleration in most of the currently proposed models, where the acceleration of particles is directly or indirectly connected to events related to clusters merging. Therefore, DM models deserve to be better studied both from the theoretical and observational sides; the best spectral bands where it is possible to obtain better information are the radio and the gamma-ray bands, while we do not expect a strong emission in the X-ray band.

79 ASTRONOMY AND ASTROPHYSICS↗

Excitation of Soliton-Type Waves in Crystals of the A{sub 3}B Stoichiometry

Using the method of molecular dynamics and taking Ni{sub 3}Al and Pt{sub 3}Al as examples, crystals of the A{sub 3}B composition are considered for the possibility of excitation of soliton-type waves in them. The potentials obtained by the embedded-atom method were used to describe interatomic interactions. It is shown that the harmonic external stimulus can excite waves of the soliton type in a Pt{sub 3}Al crystal, but not in Ni{sub 3}Al. Such compression–expansion waves are generated because of excitation of discrete breathers with soft nonlinearity that cannot exist in a Ni{sub 3}Al crystal near the affected region. The detected waves are capable of propagating to thousands of nanometers along the Pt{sub 3}Al crystal without losses of integrity and speed. The shape of the obtained wave corresponds to the kink solution of the sine-Gordon equation. The aggregate amount of energy transferred by a wave is determined by the number of rows of atoms involved in fluctuations; this may involve dozens and hundreds of electron volts.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Continuous wave laser irradiation of explosives

Quantitative measurements of the levels of continuous wave (CW) laser light that can be safely applied to bare explosives during contact operations were obtained at 532 nm, 785 nm, and 1550 nm wavelengths. A thermal camera was used to record the temperature of explosive pressed pellets and single crystals while they were irradiated using a measured laser power and laser spot size. A visible light image of the sample surface was obtained before and after the laser irradiation. Laser irradiation thresholds were obtained for the onset of any visible change to the explosive sample and for the onset of any visible chemical reaction. Deflagration to detonation transitions were not observed using any of these CW laser wavelengths on single crystals or pressed pellets in the unconfined geometry tested. Except for the photochemistry of DAAF, TATB and PBX 9502, all reactions appeared to be thermal using a 532 nm wavelength laser. For a 1550 nm wavelength laser, no photochemistry was evident, but the laser power thresholds for thermal damage in some of the materials were significantly lower than for the 532 nm laser wavelength. No reactions were observed in any of the studied explosives using the available 300 mW laser at 785 nm wavelength. Tables of laser irradiance damage and reaction thresholds are presented for pressed pellets of PBX9501, PBX9502, Composition B, HMX, TATB, RDX, DAAF, PETN, and TNT and single crystals of RDX, HMX, and PETN for each of the laser wavelengths.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Radiant Heating Cookoff Experiments and Predictive Simulations for Fast Cookoff

Thermal initiation (cookoff) of energetic material-laden devices (rocket motors and munitions) during accidental fires is an important safety concern. An article within a pool fire is an example of potential fast cookoff scenerio that has significant potential for a catastrophic result. Beginning in 2007, a collaborative experimental and model development research program under the Joint Munitions Program (JMP) was initiated at SNL/NM to address energetic material response to fast cookoff. The efforts expanded our ongoing research program studying slow cookoff phenomena and sought to answer the key question of "Can our kinetics models derived under slow cookoff conditions be applied to accurately represent energetic material behavior at fast cookoff conditions?" The simplest categorization of slow cookoff is material centered within the energetic material whereas a fast cookoff event is material ignition that occurs at a heated boundary. The external heating rate related to the heat conduction within the energetic material determines the ignition location and thus, the cookoff charaterization of slow or fast. We have developed a benchtop experiment that confines an energetic material sample and exposes it to constant incident heat fluxes common in fire in a controlled and reproducible fashion. Temperatures within the sample near the heated surface are measured using thermocouples and the time-to-event is determined as a function of incident heat flux. Insight and guidance into the experimental development has been provided by one- and three-dimensional simulations of the heat flow paths through the device. Coupling a chemical kinetics model with the heat transfer calculations enable computational predictions of time-to-ignition for comparison to the experimental data. Experimental and predicted data for PBXN-109, PBX-9501, PBX-9502, and Composition B are presented. The final section of this report presents an initial approach aimed at studing the effect of confinement on ignition and sustained reaction.

36 MATERIALS SCIENCE↗

HERMES Model Modifications and Applications 2012

HERMES was developed to meet requirements for a model to describe explosive response to impacts that do not produce prompt detonation, but can include delayed detonations such as DDT and XDT. Such response is termed High Explosive Violent Response (HEVR). The HERMES model includes a constitutive description of strength as a function of pressure, strain-rate, strain, and ambient temperature; the development of damage including fragmentation and porosity; the conditions leading to ignition; the propagation of a burning reaction through the volume of damaged explosive; the burn-up of the damaged and undamaged explosive; and the development of detonation using the Computational Reaction Evolution dependent on Entropy (S) and Time (CREST) detonation model. CREST can distinguish gradual pressure increases from shock waves, and also predict the increase in shock sensitivity to detonation that results from increased porosity. This year HERMES has been implemented as a User Defined Function in ALE 3D. As a result, modifications to the model can be implemented in a timely fashion asynchronously from the ALE 3D distribution process. There are differences between the implementation of HERMES in ALE 3D and the implementation in LS DYNA. The major difference is the propagation of an ignition front from an element that has started to burn. In LS DYNA, the time at which an element begins to burn is based on the minimum line-of-sight distance between the element and any previously ignited element. In ALE 3D the time to burn is based on a level-set method that propagates the ignition front from all elements that were previously ignited. The ALE 3D implementation modifies the time of ignition when element deformation changes the distance from the element to the source. The LS DYNA implementation does not. There are also differences in the implementation of artificial viscosity, which is important for CREST since the artificial viscosity increases the element entropy in a shock. In general, however, the differences have proven minor. In collaboration with the Atomic Weapons Establishment, UK (AWE), we have characterized two additional explosives – PETN and Composition B, a mixture of 60% RDX and 40% TNT by weight. Applications of HERMES to these explosives are described below.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Proof-of-Concept Study for Uncertainty Quantification and Sensitivity Analysis using the BRL Shaped-Charge Example

These are the slides for a graduate presentation at Mississippi State University. It covers the following: the BRL Shaped-Charge Geometry in PAGOSA, mesh refinement study, surrogate modeling using a radial basis function network (RBFN), ruling out parameters using sensitivity analysis (equation of state study), uncertainty quantification (UQ) methodology, and sensitivity analysis (SA) methodology. In summary, a mesh convergence study was used to ensure that solutions were numerically stable by comparing PDV data between simulations. A Design of Experiments (DOE) method was used to reduce the simulation space to study the effects of the Jones-Wilkins-Lee (JWL) Parameters for the Composition B main charge. Uncertainty was quantified by computing the 95% data range about the median of simulation output using a brute force Monte Carlo (MC) random sampling method. Parameter sensitivities were quantified using the Fourier Amplitude Sensitivity Test (FAST) spectral analysis method where it was determined that detonation velocity, initial density, C1, and B1 controlled jet tip velocity.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Development of ductile high-strength chromium alloys, phase 2

Strength and ductility were evaluated for chromium alloys dispersion hardened with the putative TaC, TaB, CbC, and CbB compounds. TaC and TaB proved to be the most potent strengtheners, but when combined, their effect far outweighed that produced individually. Tests at 1422 K (2100 F) on an alloy containing these two compounds at the combined level of 0.5 m/o revealed a 495 MN/sq m (70 ksi) tensile strength for wrought material, and a 100 hour rupture strength of 208 MN/sq m (30 ksi) when solution annealed and aged to maximize creep resistance. These levels of high temperature strength greatly exceed that reported for any other chromium-base alloy. The ductile-to-brittle transition temperature (DBTT) of the two phase strengthened alloy occurred at approximately 588 K (600 F) when heat treated to optimize creep strength and was not improved by fabrication to produce a wrought and recovered microstructure. The lowest DBTT measured on any of the alloys investigated was 422 K (300 F). Strengthening phases actually formed in Cr-Ta-B and Cr-Cb-B compositions are probable M2CrB2 (M=Ta or Cb) compounds of tetragonal crystal structure. The likely habit relationship between these compounds and chromium is postulated. Cube habit coherency was identified for TaC precipitation in chromium by electron microscopy. In another study, the maximum solubility of carbon in chromium was indicated to lie between 3/4 and 1 a/o and that of boron to be 1/2 a/o.

Filippi, A. M.↗

An assessment of the benefits of the use of NASA developed fuel conservative technology in the US commercial aircraft fleet

Cost and benefits of a fuel conservative aircraft technology program proposed by NASA are estimated. NASA defined six separate technology elements for the proposed program: (a) engine component improvement (b) composite structures (c) turboprops (d) laminar flow control (e) fuel conservative engine and (f) fuel conservative transport. There were two levels postulated: The baseline program was estimated to cost $490 million over 10 years with peak funding in 1980. The level two program was estimated to cost an additional $180 million also over 10 years. Discussions with NASA and with representatives of the major commercial airframe manufacturers were held to estimate the combinations of the technology elements most likely to be implemented, the potential fuel savings from each combination, and reasonable dates for incorporation of these new aircraft into the fleet.

Source record↗

Burning-to-violent-reaction transitions in explosions

In a program to study fragment initiation of cased propellants and explosives, it was found that one area of extreme importance is that of the cased reactive-material burning reactions triggered by the perforation of the case by an impacting fragment. Once the reaction is started, the importance of the impactor decreases, and the sequence of events is controlled by the burning properties of the reactive material, its physical condition, and the nature of the confinement. A brief history of the results obtained by previous investigators is presented along with a discussion of variations in experimental results caused by geometrical changes in the test configurations. Changes in interpretations of the results are discussed. Results of recent confined-burn tests with Composition B, PBXC-116, PBXC-117, and Destex are presented, including results of metallurgical examination of the confined fragments. These examinations indicate a transition to a violent reaction which is not a detonation, although it produces many effects that resemble a detonation.

Graham, K. J.↗

Novae as distance indicators

It is shown that nova shells are characteristically prolate with equatorial bands and polar caps. Failure to take this geometry into consideration can lead to large errors in expansion parallaxes for individual novae. Extinction in the bulge of M31 is investigated by projecting Arp's and Rosino's novae onto a composite B - 6200 A color map of the bulge. Of the 86 novae, 32 project onto a smooth background with no underlying structure due to the presence of a dust cloud along the line of sight. The distribution of maximum magnitudes versus fade rates for these 'unreddened' novae is indistinguishable from the distribution for the entire set of novae. It is concluded that novae suffer very little extinction from the filamentary and patchy distribution of dust seen in the bulge of M31.

Ford, Holland C.↗

Novae as distance indicators

Nova shells are characteristically prolate with equatorial bands and polar caps. Failure to account for the geometry can lead to large errors in expansion parallaxes for individual novae. When simple prescriptions are used for deriving expansion parallaxes from an ensemble of randomly oriented prolate spheroids, the average distance will be too small by factors of 10 to 15 percent. The absolute magnitudes of the novae will be underestimated and the resulting distance scale will be too small by the same factors. If observations of partially resolved nova shells select for large inclinations, the systematic error in the resulting distance scale could easily be 20 to 30 percent. Extinction by dust in the bulge of M31 may broaden and shift the intrinsic distribution of maximum nova magnitudes versus decay rates. We investigated this possibility by projecting Arp's and Rosino's novae onto a composite B - 6200A color map of M31's bulge. Thirty two of the 86 novae projected onto a smooth background with no underlying structure due to the presence of a dust cloud along the line of sight. The distribution of maximum magnitudes versus fade rates for these unreddened novae is indistinguishable from the distribution for the entire set of novae. It is concluded that novae suffer very little extinction from the filamentary and patchy distribution of dust seen in the bulge of M31. Time average B and H alpha nova luminosity functions are potentially powerful new ways to use novae as standard candles. Modern CCD observations and the photographic light curves of M31 novae found during the last 60 years were analyzed to show that these functions are power laws. Consequently, unless the eruption times for novae are known, the data cannot be used to obtain distances.

Ford, Holland C.↗