Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compressibility effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Durability Optimization of CO 2 Electrolyzers for Syngas Evolution

Recently, there has been an increased interest in mitigating anthropogenic CO 2 emissions through the electrochemical conversion of CO 2 into fuels and fuel feedstocks, including hydrogen gas (H 2 ), carbon monoxide (CO), and mixtures of the two to yield syngas. Commercial applications of these systems require high catalytic selectivity for the desired products, while exhibiting operational lifetimes exceeding thousands of hours. Advancements in this field have produced systems that display high selectivity of the desired products at faradaic efficiencies exceeding 95%. Despite the advancements made in CO 2 electrolysis, system durability remains a standing challenge in the field. CO 2 electrolyzer lifetimes are often limited by carbonate fouling, catalyst degradation, detrimental flooding of electrode microporous layers and anion exchange membrane (AEM) failures. In this report, a 5 cm 2 membrane electrode assembly (MEA) device is used to investigate potential failure modes and to optimize AEM CO 2 electrolyzer operation. Key findings of this study include the importance of CO 2 flow rate, use of a thin PiperION PTFE-reinforced membrane, optimizing compression to enhance contact under 40 in-lb compression, and the effect of more compressible, commercial iridium oxide anodes on system durability.

Abouremeleh, Mohammed H. [Lawrence Berkeley Nation↗
DOE OSTI2021

Quasi-brittle porous material: Simulated effect of stochastic air void structure on compressive strength

Highlights: • A simulation procedure to study the effect of porosity on the compressive strength of a quasi-brittle material is introduced • Based on the simulated results, the relationship between compressive strength and air void fraction (porosity) is presented. • A linear relationship was achieved between the cubic root of porosity and the simulated compressive strength. The effect of porosity comprised of spherical air voids on the compressive strength of quasi-brittle material was studied via simulations. The simulated porous structures were based on pore size distributions of two mortar samples measured by X-ray microtomography. While the simulation method set practical limits on the size of sample, the base of the statistics was established by simulating 128 small structures generated by sampling from pore structures of two mortars. By studying the application of the classical strength-porosity formulas to the simulated data, a new simple model was formed. A linear relationship was achieved between the cubic root of air void fraction (porosity) and the simulated compressive strength. The reasons for scattering of simulated strength around fitted trend remained unresolved in this study; no clear dependence on pore number or other distribution properties was observed. With the presented simulation approach, the dependence of compressive strength on porosity is achieved independently of disturbances that occur in experimental studies creating understanding of compressional behavior of low porosity materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Experimental and Numerical Investigation of a Miniature Additively Manufactured Vortex Tube

Ranque–Hilsch vortex tubes are simple devices that can produce a cooling effect using compressed air. A key advantage of vortex tubes is the lack of moving solid parts; however, their efficiencies are relatively low. The present study focuses on the development of a miniature variable-diameter tube using additive manufacturing. A metal-based 3D printing technique was utilized to fabricate this vortex tube monolithically. Computational fluid dynamics simulations employing software STAR-CCM + with a compressible Reynolds-Averaged Navier–Stokes (RANS) approach and the elliptic-blending lag k-epsilon turbulence model have been applied to model thermofluid processes inside the vortex tube, to good agreement with the experiment. In conclusion, a temperature decrease of 13.3 °C and a cooling power of approximately 4 W were experimentally achieved with a pressure ratio of 4 in the air at normal conditions. This result shows promise for the goal of utilizing additive manufacturing to design and build complex-geometry vortex tubes intended for use with cryogenic fluids.

08 HYDROGEN↗
DOE OSTI2024

The inviscid incompressible limit of Kelvin–Helmholtz instability for plasmas

The Kelvin–Helmholtz Instability (KHI) is an interface instability that develops between two fluids or plasmas flowing with a common shear layer. KHI occurs in astrophysical jets, solar atmosphere, solar flows, cometary tails, planetary magnetospheres. Two applications of interest, encompassing both space and fusion applications, drive this study: KHI formation at the outer flanks of the Earth’s magnetosphere and KHI growth from non-uniform laser heating in magnetized direct-drive implosion experiments. Here, we study 2D KHI with or without a magnetic field parallel to the flow. We use both the GAMERA code, which solves the compressible Euler equations, and the STRATOSPEC code, which solves the Navier-Stokes equations under the Boussinesq approximation, coupled with the magnetic field dynamics. GAMERA is a global three-dimensional MHD code with high-order reconstruction in arbitrary nonorthogonal curvilinear coordinates, which is developed for a large range of astrophysical applications. STRATOSPEC is a three-dimensional pseudo-spectral code with an accuracy of infinite order (no numerical diffusion). Magnetized KHI is a canonical case for benchmarking hydrocode simulations with extended MHD options. An objective is to assess whether or not, and under which conditions, the incompressibility hypothesis allows to describe a dynamic compressible system. For comparing both codes, we reach the inviscid incompressible regime, by decreasing the Mach number in GAMERA, and viscosity and diffusion in STRATOSPEC. Here, we specifically investigate both single-mode and multi-mode initial perturbations, either with or without magnetic field parallel to the flow. The method relies on comparisons of the density fields, 1D profiles of physical quantities averaged along the flow direction, and scale-by-scale spectral densities. We also address the triggering, formation and damping of filamentary structures under varying Mach number or Atwood number, with or without a parallel magnetic field. Comparisons show very satisfactory results between the two codes. The vortices dynamics is well reproduced, along with the breaking or damping of small-scale structures. We end with the extraction of growth rates of magnetized KHI from the compressible regime to the incompressible limit in the linear regime assessing the effects of compressibility under increasing magnetic field. The observed differences between the two codes are explained either from diffusion or non-Boussinesq effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Contrasting c -axis and in-plane uniaxial stress effects on superconductivity and stripe order in La 1.885 Ba 0.115 CuO 4

The cuprate superconductor La 2−x Ba x CuO 4 (LBCO) near x = 0.125 is a striking example of intertwined electronic orders, where 3D superconductivity is anomalously suppressed, allowing spin and charge stripe order to develop. Understanding this interplay remains a key challenge in cuprates, highlighting the necessity of external tuning for deeper insight. While in-plane uniaxial stress enhances superconductivity and suppresses stripe order, the effects of c -axis compression remains largely unexplored. Here, we use muon spin rotation ( μ SR) and AC susceptibility with an in situ piezoelectric stress device to investigate the spin-stripe order and superconductivity in LBCO-0.115 under c-axis compression. The measurements reveal a gradual suppression of the superconducting transition temperature ( T c ) with increasing c -axis stress, in stark contrast to the strong enhancement observed under in-plane stress. We further show that while in-plane stress rapidly reduces both the magnetic volume fraction ( V m ) and the spin-stripe ordering temperature ( T so ), c-axis compression has no effect, with V m and T so exhibiting an almost unchanged behavior up to the highest applied stress of 0.21 GPa. These findings demonstrate a strong anisotropy in stress response.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Preferential turbulence enhancement in two-dimensional compressions

When initially isotropic three-dimensional (3D) turbulence is compressed along two dimensions, the compression supplies energy directly to the flow components in the compressed directions, while the flow component in the noncompressed direction experiences the effects of compression only indirectly through the nonlinearity of the hydrodynamic equations. Here we present our study of such 2D compressions using numerical simulations. For initially isotropic turbulence, we find that the nonlinearity can be insufficient to maintain isotropy, with the energy components parallel to the compression coming to dominate the turbulent energy, with a number of consequences. Among these are the possibilities for stronger and more easily sustained growth of turbulent energy than in 3D compressions and for an increasing turbulent Mach number even in a compression without thermal losses.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Effect of lattice orientation on compressive properties of selective laser sintered nylon lattice coupons

As AM lattices become more popular in medical devices, it is important to consider how lattice design parameters affect the mechanical integrity and performance of a device. This research investigated the effect of lattice orientation on the compressive mechanical response of five common lattice geometries: Hexagonal Honeycomb (Hex), Diamond, Voronoi Tessellation Method (VTM), sheet-based Gyroid, and Face-Centered-Cubic (FCC). Samples were tested at two relative densities and eight orientations, printed in Nylon 12 (PA2200) on an EOS P396. The mechanical response was compared to simulated finite element analysis (FEA) response for Hex and FCC lattices. Hex lattices displayed significant orientation dependance. Diamond lattices demonstrated some orientation dependance when at a lower relative density. Gyroid, FCC, and VTM all displayed minimal orientation dependance. Increasing lattice relative density appeared to reduce anisotropy among tested orientations of all lattice geometries except Hex. FEA simulations were able to produce a trend response that matched the mechanical response trends based on the investigated orientations. Furthermore, these results support the need for multi axial lattice mechanical test considerations. It also bolsters the need for lattice FEA models to have a sufficient comparator when identifying “worst-case” lattice test scenarios.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Anisotropic-strain-enhanced hole mobility in GaN by lattice matching to ZnGeN 2 and MgSiN 2

The key obstacle toward realizing integrated gallium nitride (GaN) electronics is its low hole mobility. Here, we explore the possibility of improving the hole mobility of GaN via epitaxial matching to II–IV nitride materials that have recently become available, namely, ZnGeN 2 and MgSiN 2 . We perform state-of-the-art calculations of the hole mobility of GaN using the ab initio Boltzmann transport equation. We show that effective uniaxial compressive strain of GaN along the [$1\bar{1}00$] by lattice matching to ZnGeN 2 and MgSiN 2 results in the inversion of the heavy hole band and split-off hole band, thereby lowering the effective hole mass in the compression direction. We find that lattice matching to ZnGeN 2 and MgSiN 2 induces an increase in the room-temperature hole mobility by 50% and 260% as compared to unstrained GaN, respectively. Further, examining the trends as a function of strain, we find that the variation in mobility is highly nonlinear; lattice matching to a hypothetical solid solution of Zn 0.75 Ge 0.75 Mg 0.25 Si 0.25 N 2 would already increase the hole mobility by 160%.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fracture Sustainability in Enhanced Geothermal Systems: Experimental and Modeling Constraints

Enhanced geothermal systems (EGS) offer the potential for a much larger energy source than conventional hydrothermal systems. Hot, low-permeability rocks are prevalent at depth around the world, but the challenge of extracting thermal energy depends on the ability to create and sustain open fracture networks. Laboratory experiments were conducted using a suite of selected rock cores (granite, metasediment, rhyolite ash-flow tuff, and silicified rhyolitic tuff) at relevant pressures (uniaxial loading up to 20.7 MPa and fluid pressures up to 10.3 MPa) and temperatures (150–250 °C) to evaluate the potential impacts of circulating fluids through fractured rock by monitoring changes in fracture aperture, mineralogy, permeability, and fluid chemistry. Because a fluid in disequilibrium with the rocks (deionized water) was used for these experiments, there was net dissolution of the rock sample: this increased with increasing temperature and experiment duration. Thermal-hydrological-mechanical-chemical (THMC) modeling simulations were performed for the rhyolite ash-flow tuff experiment to test the ability to predict the observed changes. These simulations were performed in two steps: a thermal-hydrological-mechanical (THM) simulation to evaluate the effects of compression of the fracture, and a thermal-hydrological-chemical (THC) simulation to evaluate the effects of hydrothermal reactions on the fracture mineralogy, porosity, and permeability. Furthermore, these experiments and simulations point out how differences in rock mineralogy, fluid chemistry, and geomechanical properties influence how long asperity-propped fracture apertures may be sustained. Such core-scale experiments and simulations can be used to predict EGS reservoir behavior on the field scale.

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Investigation of the effects of turbulence modeling on the prediction of compression-ignition combustion unsteadiness

Adverse effects of global warming due to the greenhouse gas emissions is changing the actual paradigm for the use energy resources. In the absence of a mid-term solution for reducing these emissions in transportation, internal combustion (IC) engines are going to coexist in the social spheres in the foreseeable future. Therefore, the study of other IC engine-related problems remains relevant to ensuring the health of the society. In this investigation, a numerical methodology for comprehensive understanding of Noise, Vibration and Harshness in internal combustion engines is proposed. Due to its inherent complexity and lack of awareness, the main objective is to evaluate the impact of the turbulence modeling framework on the in-cylinder acoustic field recreation. Modal decomposition methods have been applied to isolate the coherent flow structures and to analyze how they change with the turbulence approach. Results demonstrate that the choice of the turbulence model is a critical aspect for noise modeling. Unsteady Reynolds-Averaged Navier-Stokes schemes predict a raw estimation of the internal acoustic field with the added value of being computationally less expensive. However, the use of more complex turbulence approaches such us large eddy simulation offers an accurate prediction of the acoustic structures and their cyclic dispersion.

Broatch, A.↗
DOE OSTI2026

Nonlinear post-compression to sub-20 fs using a single-stage multipass cell filled with ambient air

Noble gas-filled multipass cells have proven to be very effective in compressing high-energy, hundreds-of-femtoseconds pulses down to tens of femtoseconds. Molecular gases can be an attractive alternative to noble gases since they provide additional Raman nonlinearities that can be much stronger than the electronic Kerr nonlinearity and can therefore enable more spectral broadening and shorter compressed pulses. Air at atmospheric pressure offers molecular gases in their simplest format, with both easy access and no costs for implementing a gas chamber. Here we demonstrate a single-stage, air-filled multipass cell that spectrally broadens 145- μ J, 185-fs pulses with >90% throughput, with a small fraction of the output compressed to sub-20 fs using a prism-pair compressor. The multipass cell uses standard broadband mirrors without dispersion engineering and ambient air as the nonlinear medium, making it the simplest and most cost-effective solution for generating few-cycle femtosecond pulses.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Heating performance of a vapor compression heat pump cascaded with a thermoelectric heat pump

Air source heat pumps (ASHPs) are widely utilized for heating and cooling in residential buildings; however, their effectiveness in heating mode is compromised during extreme weather conditions. Extensive research endeavors have been undertaken to develop, test, and assess a cost-effective vapor compression ASHP suitable for cold climate regions. Further, this study takes an innovative approach by developing component and system prototypes for a cold climate heat pump. This design combines a thermoelectric heat pump (TEHP) with a traditional residential split ASHP to augment heating capacity in low ambient temperature conditions. The component and system prototypes underwent experimental testing in the psychrometric chambers. The experimental findings revealed a 13.6% to 13.7% increase in total heat pump heating capacity, accompanied by a 3.1% to 5.0% decrease in the coefficient of performance (COP) at ambient temperatures of -15°C and -19°C, when compared to the original ASHP. The COP of the TEHP is relatively constant, ranging from 1.63 to 1.76. This prototype offers a solution to address the challenges associated with reduced heat pump capacity at low ambient temperatures. The experimental results indicated that the lower the ambient temperature, thermoelectric heat pump auxiliary heating can increase the heating efficiency 60% in comparison to electric resistance.

42 ENGINEERING↗
DOE OSTI2023

Chapman–Jouguet deflagration criteria and compressibility dynamics of turbulent fast flames for turbulence-induced deflagration-to-detonation transition

This work characterizes the compressibility dynamics in turbulent fast flames for a range of turbulent flame speeds. These turbulent fast flames experience increased effects of compressibility through the formation of strong shocks and may develop a runaway acceleration combined with a pressure buildup that leads to turbulence induced deflagration-to-detonation transition (tDDT). Simultaneous high-speed particle image velocimetry, OH* chemiluminescence, schlieren, and pressure measurements are used to examine the reacting flow field and flame dynamics. We examine flames with turbulent flame speeds ranging from 100 to 600 m/s. At lower turbulent flame speeds, the flame is not able to produce favorable background conditions for deflagration-to-detonation transition (DDT) onset, and thus flame compressibility and turbulence amplification are less dominant, resulting in a weaker acoustic coupling between the flame and compressed region. As the turbulent burning velocities exceed the Chapman–Jouguet deflagration speed, favorable background conditions are produced, as we observe flame-generated shocks and flame-generated turbulence with higher turbulent velocities and larger turbulent scales. At this regime, the flame is categorized to be at the runaway transition regime that leads to tDDT.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Tension-compression asymmetry in superelasticity of SrNi 2 P 2 single crystals and the influence of low temperatures

ThCr 2 Si 2 -type intermetallic compounds are known to exhibit superelasticity associated with structural transitions through lattice collapse and expansion. These transitions occur via the formation and breaking of Si-type bonds, respectively, under uniaxial loading along the [0 0 1] direction. Unlike most ThCr 2 Si 2 -type intermetallic compounds, which have either an uncollapsed tetragonal structure or a collapsed tetragonal structure, SrNi 2 P 2 possesses a third type of collapsed structured: a one-third orthorhombic structure, for which one expects the occurrence of unique structural transitions and superelastic behavior. In this study, uniaxial compression and tension tests were conducted on micron-sized SrNi 2 P 2 single crystalline columns at room temperature, 200 K, and 100 K, to investigate the influence of loading direction and temperature on the superelasticity of SrNi 2 P 2 . Experimental data and density functional theory calculations revealed the presence of tension-compression asymmetry in the structural transitions and superelasticity, as well as an asymmetry in their temperature dependence, due to the opposite superelastic process associated with compression (forming P-P bonds) and tension (breaking P-P bonds). Additionally, following thermodynamics, the observations suggest that this asymmetric superelasticity could lead to an opposite elastocaloric effect between compression and tension, which could be beneficial potentially in obtaining large temperature changes compared to conventional superelastic solids that show the same elastocaloric effect regardless of loading direction. Furthermore, these results provide an important fundamental insight into the structural transitions, superelasticity processes, and potential elastocaloric effects in SrNi 2 P 2 .

36 MATERIALS SCIENCE↗