Search NASA⌕ Search

SEARCH · Search NASA

Results for “DRAG REDUCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Effect of detailed surface geometry on riblet drag reduction performance

A comparison is made of the effect of small changes in v-groove geometry, for several riblet films applicable for drag reduction to commercial transport aircraft, whose nominal v-groove dimension is of the order of 0.002 inch. The films were tested in a water towing-tank facility. The results obtained indicate that small riblet peak geometry variations can result in a deterioration of riblet drag-reduction efficacy of as much as 40 percent, while interriblet valley curvature was found not to be critical to riblet performance.

Walsh, Michael J.↗
NASA NTRS1981

Longitudinal grooves for bluff body drag reduction

Wind tunnel test results are presented for four axisymmetric bluff body configurations in order to determine their effect on form and pressure drag. It was found that drag reductions on the order of 40% are obtainable with an afterbody incorporating four longitudinal 'V' grooves. Although this effect may be due to the functioning of the grooves as longitudinal, continuous vortex generators, it is concluded that further research is needed to elucidate the physical basis of the test results. Optimization of the effect will be useful in base drag reduction for such vehicles as automobiles and cargo aircraft with sharply upswept afterbodies.

Quass, B.↗
NASA NTRS1987

What happens to the large eddies when net drag reduction is achieved by outer flow manipulators?

The tandem-arranged parallel plate manipulator (TAPPM) presently used to generate a flow with net drag reduction is conditionally sampled and found to exhibit significant changes of the boundary layer's large-scale motions at 20 delta(0), where delta(0) is the boundary layer thickness at the upstream plate of the TAPPM. Flow fields in the 'valleys' are equally affected. Both turbulent and irrotational flows then reestablish themselves by 50 delta(0). Flow visualization indicates that the TAPPM wake is very coherent at 20 delta(0), and has not yet spread into the wall region, while large scale motions and the ambient response flow continue to exhibit dynamic changes. This indicates that the shielding effect of the TAPPM's wake prolongs suppression of large-scale motions, thereby reducing skin friction over a sufficiently long extent of the boundary layer to overcome device drag and yield net drag reductions.

Falco, R. E.↗
NASA NTRS1980

Analytical and design techniques for drag reduction studies on wavy surfaces

Numerical models for two dimensional turbulent boundary layers over wavy surfaces were investigated. Computations for wavy wall boundary layers indicate possibilities of overall drag reduction in a parameter range of the geometry of the wall. The correction technique using integral methods for analyzing arbitrary surfaces was found to be unsuitable for some cases of interest in drag reduction; a Navier-Stokes solver for wavy walls was built to test these problems. Test results of the Navier-Stokes solver indicate that the solution techniques are accurate enough to handle complex geometries and steep variations in fluid properties.

Balasubramanian, R.↗
NASA NTRS1982

Turbulent boundary layer drag reduction using riblets

An experimental study of low-speed turbulent boundary layer flow over longitudinally grooved surfaces (i.e., riblets) is discussed. Results obtained with a highly accurate drag balance indicate that v-groove riblet surfaces can produce consistent net drag reductions as large as 8 percent provided the height and spacing of the grooves in terms of law of the wall variables are less than 25 wall units. Momentum balances confirmed these direct drag measurements. Conditionally sampled data indicate that the burst frequency for riblets is approximately the same as that for a flat plate but turbulence intensity is reduced. Attempts to optimize the net drag reduction by varying riblet cross-sectional geometry and alignment are also discussed.

Walsh, M. J.↗
NASA NTRS1983

Alteration of outer flow structures for turbulent drag reduction

Paper reviews large eddy behavior in turbulent boundary layers and presents a survey of turbulent wall layers subjected to abrupt changes in boundary conditions. From this survey several methods have been identified with potential for altering the turbulence production process in the outer region of the boundary layer and reducing the turbulent skin-friction drag over relatively long downstream distances; these include convex longitudinal surface curvature, large-eddy breakup devices, and Emmons spot alteration. Paper also presents results of an ongoing experimental study to parametrically evaluate large-eddy breakup devices as a turbulent drag reduction concept and reproduce the 20 percent net drag reductions found in large-eddy breakup experiments at Illinois Institute of Technology.

Hefner, J. N.↗
NASA NTRS1996

Drag Reduction Devices for Aircraft (Latest Citations from the Aerospace Database)

The bibliography contains citations concerning the modeling, application, testing, and development of drag reduction devices for aircraft. Slots, flaps, fences, large-eddy breakup (LEBU) devices, vortex generators and turbines, Helmholtz resonators, and winglets are among the devices discussed. Contour shaping to ensure laminar flow, control boundary layer transition, or minimize turbulence is also covered. Applications include the wings, nacelles, fuselage, empennage, and externals of aircraft designed for high-lift, subsonic, or supersonic operation. The design, testing, and development of directional grooves, commonly called riblets, are covered in a separate bibliography.(Contains 50-250 citations and includes a subject term index and title list.)

AIRCRAFT DESIGN↗
NASA NTRS1986

Airfoil large eddy breakup devices for turbulent drag reduction

It was determined from the present LaRC experiments that tandem, airfoil-shaped large eddy breakup (LEBU) devices can reduce local skin friction as much as 30 percent with a recovery region extending more than 100 boundary layer thicknesses downstream. These airfoils experience near laminar skin friction device drag and produce net drag reductions of up to 7 percent. In contrast to the thin plates used in previous experiments, these airfoils are more than 1000 time stiffer and hence have the potential to withstand the real flight environment (dynamic pressure 36 times larger than in low-speed wing tunnels). In addition, the higher Reynolds numbers of the present tests indicate drag reduction performance is at least as good (or better) as at lower Reynolds numbers.

Anders, J. B.↗
NASA NTRS2017

Transonic Drag Reduction Through Trailing-Edge Blowing on the FAST-MAC Circulation Control Model

A third wind tunnel test of the FAST-MAC circulation control semi-span model was completed in the National Transonic Facility at the NASA Langley Research Center where the model was configured for transonic testing of the cruise configuration with 0deg flap detection to determine the potential for transonic drag reduction with the circulation control blowing. The model allowed independent control of four circulation control plenums producing a high momentum jet from a blowing slot near the wing trailing edge that was directed over a 15% chord simple-hinged ap. Recent upgrades to transonic semi-span flow control testing at the NTF have demonstrated an improvement to overall data repeatability, particularly for the drag measurement, that allows for increased confidence in the data results. The static thrust generated by the blowing slot was removed from the wind-on data using force and moment balance data from wind-o thrust tares. This paper discusses the impact of the trailing-edge blowing to the transonic aerodynamics of the FAST-MAC model in the cruise configuration, where at flight Reynolds numbers, the thrust-removed corrected data showed that an overall drag reduction and increased aerodynamic efficiency was realized as a consequence of the blowing.

Chan, David T.↗
NASA NTRS1980

Drag reduction - Jet breakup correlation with kerosene-based additives

The drag-reduction effectiveness of a number of high-polymer additives dissolved in aircraft fuel has been measured in a turbulent-flow rheometer. These solutions were further subjected to high elongational stress and breakup forces in a jet discharging in air. The jet was photographed using a high-resolution camera with special lighting. The object of the work was to study the possible spray-suppression ability of high-polymer additives to aircraft fuel and to correlate this with the drag-reducing properties of the additives. It was found, in fact, that the rheometer results indicate the most effective spray-suppressing additives. Using as a measure the minimum polymer concentration to give a maximum friction-reducing effect, the order of effectiveness of eight different polymer additives as spray-suppressing agents was predicted. These results may find application in the development of antimisting additives for aircraft fuel which may increase fire safety in case of crash or accident.

Hoyt, J. W.↗
NASA NTRS2005

On the Application of Contour Bumps for Transonic Drag Reduction(Invited)

The effect of discrete contour bumps on reducing the transonic drag at off-design conditions on an airfoil have been examined. The research focused on fully-turbulent flow conditions, at a realistic flight chord Reynolds number of 30 million. State-of-the-art computational fluid dynamics methods were used to design a new baseline airfoil, and a family of fixed contour bumps. The new configurations were experimentally evaluated in the 0.3-m Transonic Cryogenic Tunnel at the NASA Langley Research center, which utilizes an adaptive wall test section to minimize wall interference. The computational study showed that transonic drag reduction, on the order of 12% - 15%, was possible using a surface contour bump to spread a normal shock wave. The computational study also indicated that the divergence drag Mach number was increased for the contour bump applications. Preliminary analysis of the experimental data showed a similar contour bump effect, but this data needed to be further analyzed for residual wall interference corrections.

Milholen, William E., II↗
NASA NTRS2005

On the Application of Contour Bumps for Transonic Drag Reduction(Invited)

The effect of discrete contour bumps on reducing the transonic drag at off-design conditions on an airfoil have been examined. The research focused on fully-turbulent flow conditions, at a realistic flight chord Reynolds number of 30 million. State-of-the-art computational fluid dynamics methods were used to design a new baseline airfoil, and a family of fixed contour bumps. The new configurations were experimentally evaluated in the 0.3-m Transonic Cryogenic Tunnel at the NASA Langley Research center, which utilizes an adaptive wall test section to minimize wall interference. The computational study showed that transonic drag reduction, on the order of 12% - 15%, was possible using a surface contour bump to spread a normal shock wave. The computational study also indicated that the divergence drag Mach number was increased for the contour bump applications. Preliminary analysis of the experimental data showed a similar contour bump effect, but this data needed to be further analyzed for residual wall interference corrections.

Milholen, William E., II↗
NASA NTRS1975

A comprehensive plan for helicopter drag reduction

Current helicopters have parasite drag levels 6 to 10 times as great as fixed wing aircraft. The commensurate poor cruise efficiency results in a substantial degradation of potential mission capability. The paper traces the origins of helicopter drag and shows that the problem (primarily due to bluff body flow separation) can be solved by the adoption of a comprehensive research and development plan. This plan, known as the Fuselage Design Methodology, comprises both nonaerodynamic and aerodynamic aspects. The aerodynamics are discussed in detail and experimental and analytical programs are described which will lead to a solution of the bluff body problem. Some recent results of work conducted at the Naval Ship Research and Development Center (NSRDC) are presented to illustrate these programs. It is concluded that a 75-per cent reduction of helicopter drag is possible by the full implementation of the Fuselage Design Methodology.

Williams, R. M.↗
NASA NTRS1977

Prediction of compliant wall drag reduction, part 1

Computer codes developed to test Bushnell's compliant wall drag reduction model are discussed. One code computes the evolution of mean velocity profiles during the period between bursts as forced by an imposed large-scale pressure pulse due to earlier bursts. Another code computes the local stability characteristics of these computed profiles. The programs use Chebyshev polynomials to resolve the normal boundary layer (y) direction and a staggered grid of mesh points to resolve the x direction. Typically, 257 grid points and 33 Chebyshev polynomials are used in the computations.

Orszag, S. A.↗
NASA NTRS1980

Drag reduction characteristics of small amplitude rigid surface waves

The possibility of reducing drag by using rigid, wavy surfaces is investigated both analytically and experimentally. Although pressure drag for rigid sine-wave surfaces can be predicted empirically, viscous drag for even shallow waves was poorly predicted by state-of-the-art turbulent boundary layer calculation procedures. Calculations for the effects of geometric and fluid variables on total wave drag are presented under the philosophy that trends will be nearly correct even though levels are probably incorrect. Experiments by the present authors indicate that a total drag reduction with wavy walls is possible.

Cary, A. M., Jr.↗
NASA NTRS1976

Airfoil section drag reduction at transonic speeds by numerical optimization

A practical procedure for the design of low drag, transonic airfoils is demonstrated. The procedure uses an optimization program, based on a gradient algorithm coupled with an aerodynamic analysis program, that solves the full, non-linear potential equation for transonic flow. The procedure is useful for the design of retrofit modifications for drag reduction of existing aircraft as well as for the design of low drag profiles for new aircraft. Results are presented for the modification of four different airfoils to decrease the drag at a given transonic Mach number.

Hicks, R. M.↗
NASA NTRS1976

Airfoil section drag reduction at transonic speeds by numerical optimization

A practical procedure for the design of low drag, transonic airfoils is demonstrated. The procedure uses an optimization program, based on a gradient algorithm coupled with an aerodynamic analysis program, that solves the full, non-linear potential equation for transonic flow. The procedure is useful for the design of retrofit modifications for drag reduction of existing aircraft as well as for the design of low drag profiles for new aircraft. Results are presented for the modification of four different airfoils to decrease the drag at a given transonic Mach number.

Hicks, R. M.↗