Results for “FREQUENCY RANGE” — Page 4

DOE OSTI2021

Optical Spectrometer With a Pulse-to-Pulse Resolution for Terahertz and mm-Wave Signals

The development of ultra-compact particle accelerators and accelerator-based high-power THz generators are some of the top priorities for research and development programs around the world. These tools require the development of accelerating structures, operating in the mm-Wave and THz range, where diagnostics are not available or are insufficient. This article presents the design of a pulse-to-pulse THz spectrometer, primarily developed for diagnostics of accelerating structures and THz radiation sources. In particular, this spectrometer can be used to detect RF pulse shortening caused by vacuum breakdown and beam misalignment in THz accelerators, as well as for bunch length monitoring and radiation source diagnostics. The spectrometer is based on a diffraction grating and is capable of covering a frequency range where RF-based breakdown measurements are not possible. We have built and tested the first prototype with different sources in a frequency range of 0.1-1.0 THz. In this article, we present the physical design, supported numerical simulations, electronics development, and test results.

47 OTHER INSTRUMENTATION↗

DOE OSTI2024

Axion Dark Matter eXperiment: Run 1A analysis details

The ADMX Collaboration gathered data for its Run 1A axion dark matter search from January 2017 to June 2017, scanning with an axion haloscope over the frequency range 645–680 MHz ( 2.66 – 2.81 μ eV in axion mass) at Dine-Fischler-Srednicki-Zhitnitskii (DFSZ) sensitivity. The resulting axion search found no axionlike signals comprising all the dark matter in the form of a virialized galactic halo over the entire frequency range, implying lower bound exclusion limits at or below DFSZ coupling at the 90% confidence level. This paper presents expanded details of the axion search analysis of Run 1A, including review of relevant experimental systems, data-taking operations, preparation and interpretation of raw data, axion search methodology, candidate handling, and final axion limits. Published by the American Physical Society 2024

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2022

A Pockels cell enabled heterodyne phase contrast imaging diagnostic for detection of ion cyclotron emission

This work describes a novel optical heterodyne detection scheme that significantly extends the frequency response of the phase contrast imaging method to detect electron density fluctuations in tens of megahertz frequency range. The system employs a variable frequency electro-optic modulator to allow operation at any frequency in the range 10–40 MHz without the need to realign the system. The frequency coverage of the system makes it suitable to measure the radial structure of the electron density component of ion cyclotron emission on devices having confining magnetic field of a few tesla, thus extending the purely temporal measurements provided so far by magnetic probes.

47 OTHER INSTRUMENTATION↗

DOE OSTI2026

Measurement Adequacy for Monitoring Data Center Oscillations

Artificial intelligence (AI) training data centers with periodic load profiles can induce sustained grid oscillations across a wide frequency range, making accurate monitoring essential for reliable power system operation. This report evaluates the adequacy of existing measurement systems for monitoring such oscillations, focusing on phasor measurement units (PMUs) and point-on-wave (POW) measurement systems. The analysis shows that while PMUs are highly effective for monitoring low-frequency electromechanical oscillations, they have inherent limitations in accurately representing higher-frequency oscillations due to constraints imposed by reporting rates and the bandwidth of phasor estimation filters. Even when configured with higher reporting rates, the filtering inherent in the phasor estimation process can significantly attenuate oscillation magnitudes, potentially leading to underestimation of oscillatory behavior. This has important implications for compliance and performance monitoring of large loads. To address the limitations associated with PMU-based monitoring, the report examines the use of high-resolution POW measurements, which can capture oscillations across a broader frequency range. However, continuous POW monitoring introduces practical challenges related to large data volumes, communication bandwidth, and real-time data processing. For this reason, the report also discusses emerging approaches that use POW measurements as a complementary capability alongside PMUs to improve observability of oscillations from large data center loads.

47 OTHER INSTRUMENTATION↗

DOE OSTI2022

In-plane and through-plane dielectric properties of graphene oxide membrane: Effect of Al 3 + modification

A graphene oxide (GO) membrane can be used in structural dielectric capacitors and planar micro-supercapacitors as a dielectric separator material due to its excellent through-plane and in-plane dielectric properties. The ability to tailor the dielectric properties of the GO membrane is crucial for dielectric applications. We believe this to be the first demonstration describing how Al 3+ ions impact the dielectric properties of the GO membrane through cation to oxygenated functional groups interactions. In this work, the Al 3+ -modification to the GO membrane was realized through a facile pre-coordination method followed by layer-by-layer assembling. The influence of Al 3+ on the GO membranes’ through-plane and in-plane dielectric properties (dielectric constant and dielectric loss) was investigated in the frequency range from 0.01 Hz to 10 5 Hz. Plane-to-plane and edge-to-edge Al 3+ coordination with the functional group on the basal plane or edge of the GO sheets was proposed to understand the metal ion's impact on the dielectric properties. The results demonstrated that the Al 3+ modification was an effective strategy to tailoring the GO membranes’ dielectric properties in a low frequency regime and further suggested the possibility of designing dielectric GO membranes with controllable dielectric performance. At a low frequency range (0.01–1 Hz), the addition of Al 3+ increased the through-plane dielectric constant and decreased the in-plane dielectric constant. In terms of dielectric loss, unmodified GO membranes exhibited a higher in-plane dielectric loss than the through-plane dielectric loss. Al 3+ -modified GO membranes exhibited increased through-plane dielectric loss and decreased in-plane dielectric loss compared to the unmodified GO membranes.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Noise limits for dc SQUID readout of high- Q resonators below 300 MHz

We present the limits on noise for the readout of cryogenic high-Q resonators using dc Superconducting Quantum Interference Devices (SQUIDs) below 300 MHz. This analysis uses realized first-stage SQUIDs (previously published), whose performance is well described by Tesche–Clarke (TC) theory, coupled directly to the resonators. We also present data from a prototype second-stage dc SQUID array designed to couple to this first-stage SQUID as a follow-on amplifier with high system bandwidth. This analysis is the first full consideration of dc SQUID noise performance referred to a high-Q resonator over this frequency range and is presented relative to the standard quantum limit. We include imprecision, backaction, and backaction–imprecision noise correlations from TC theory, the noise contributed by the second-stage SQUIDs, wiring, and preamplifiers, and optimizations for both on-resonance measurements and off-resonance scan sensitivity. This architecture has modern relevance due to the increased interest in axion searches and the requirements of the DMRadio-m 3 axion search, which uses dc SQUIDs in this frequency range.

Bosons↗

DOE OSTI2025

Ion dynamics in hexagonal boron nitride ionogel electrolytes

Ionogel electrolytes incorporating exfoliated hexagonal boron nitride (hBN) nanoplatelets are promising materials for next-generation energy storage systems. However, detailed understanding of their ion transport properties at the molecular level remains limited. This study employs diffusion and relaxation nuclear magnetic resonance (NMR) techniques, including fast-field cycling (FFC) NMR, to investigate the dynamics of ionic species in hBN-ionogels. By spanning a broad frequency range from 30 kHz using FFC NMR to high-field NMR (500–800 MHz), we reveal distinct relaxation mechanisms governing ion dynamics in ionogels with and without lithium salts. Our results highlight the role of hBN in modulating molecular rotation and translational motion, significantly affecting 1 H and 19 F relaxation profiles. The presence of Li + alters the dynamic behavior in ionogels, enhancing anion mobility at the interface. Notably, 7 Li relaxation reveals strong interactions with the hBN surface that cannot be detected by diffusion NMR. Furthermore, these findings underscore the importance of spanning a broad frequency range in NMR studies of ionogels and provide critical insights into optimizing their design as novel electrolytes.

Electrolytes↗

DOE OSTI2021

Giant Polarization in Nanodielectrics

The relative permittivity of a material is a scaling factor for capacitors and the devices based upon them; the larger the relative permittivity, the greater the degree of miniaturization, or potential for energy storage. Materials with a relative permittivity than that of silicon nitride (approximately 7) are referred to as high-dielectric constant materials. Values of about 100 are typical in titanium dioxide rutile. Values of about 10,000 are observed in barium titanate in the region of the ferroelectric transition, which while impressive, is not very useful due to the strong temperature dependence. The observation of a relative permittivity of over 100,000 in the calcium copper titanate material sparked considerable interest because it showed little temperature dependence between 100 and 600 K over most of the radio-frequency range. Further investigation revealed that this material appears to be naturally nanotextured and that the colossal permittivity was likely due to the surface and/or internal barrier layer capacitance effect, although the issue is not settled. Unfortunately, the dielectric losses in this class materials are relatively high. A new strategy to achieve high dielectric permittivity with low loss involves using localized lattice defect states through ambipolar co-doping; these intrinsic defect complexes give rise to strong dipoles that are responsible for a relative permittivity of 10,000 with exceptionally low dielectric losses over most of the radio frequency range and excellent thermal stability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

Giant polarization in nanodielectrics

The relative permittivity of a material is a scaling factor for capacitors and the devices based upon them; the larger the relative permittivity, the greater the degree of miniaturization, or potential for energy storage. Materials with a relative permittivity than that of silicon nitride (approximately 7) are referred to as high-dielectric constant materials. Values of about 100 are typical in titanium dioxide rutile. Values of about 10,000 are observed in barium titanate in the region of the ferroelectric transition, which while impressive, is not very useful due to the strong temperature dependence. The observation of a relative permittivity of over 100,000 in the calcium copper titanate material sparked considerable interest because it showed little temperature dependence between 100 and 600 K over most of the radio-frequency range. Further investigation revealed that this material appears to be naturally nanotextured and that the colossal permittivity was likely due to the surface and/or internal barrier layer capacitance effect, although the issue is not settled. Unfortunately, the dielectric losses in this class materials are relatively high. A new strategy to achieve high dielectric permittivity with low loss involves using localized lattice defect states through ambipolar co-doping; these intrinsic defect complexes give rise to strong dipoles that are responsible for a relative permittivity of 10,000 with exceptionally low dielectric losses over most of the radio frequency range and excellent thermal stability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

Progress in High-Dielectric Constant Materials

The relative permittivity of a material is a scaling factor for capacitors and the devices based upon them; the larger the relative permittivity, the greater the degree of miniaturization, or potential for energy storage. Materials with a relative permittivity than that of silicon nitride (approximately 7) are referred to as high-dielectric constant materials. Values of about 100 are typical in titanium dioxide rutile. Values of about 10,000 are observed in barium titanate in the region of the ferroelectric transition, which while impressive, is not very useful due to the strong temperature dependence. The observation of a relative permittivity of over 100,000 in the calcium copper titanate material sparked considerable interest because it showed little temperature dependence between 100 and 600 K over most of the radio-frequency range. Further investigation revealed that this material appears to be naturally nanotextured and that the colossal permittivity was likely due to the surface and/or internal barrier layer capacitance effect, although the issue is not settled. Unfortunately, the dielectric losses in this class materials are relatively high. A new strategy to achieve high dielectric permittivity with low loss involves using localized lattice defect states through ambipolar co-doping; these intrinsic defect complexes give rise to strong dipoles that are responsible for a relative permittivity of 10,000 with exceptionally low dielectric losses over most of the radio frequency range and excellent thermal stability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2022

Interferometric bunch length measurements of 3 MeV picocoulomb electron beams

We report picosecond bunch length measurements using an interferometric method for a 3 MeV electron beam having bunch charge ranging from 1 to 14 pC. The method senses the single-cycle sub-terahertz (THz) pulse emitted by each electron bunch as coherent transition radiation which, in turn, is analyzed using a Michelson-type interferometer, forming an interferogram that is then processed to yield the nominal electron bunch length. This sub-THz coherent radiation intensity was measured using a quasi-optical detector (QOD) operated at room temperature. This experiment was quite challenging since the divergence angle of the sub-THz pulse emitted by the low-energy electron bunch exceeds ±10°, and its pulse energy at the entrance to the detector was as low as 100 pJ. When compared to a conventional helium-cooled silicon composite bolometer designed for frequencies above 0.5 THz, the QOD provided much better signal-to-noise ratio in the ~80 GHz frequency range, which was critical for the successful measurement of the bunch length.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Ultra-thin on-chip ALD LiPON capacitors for high frequency application

Multi-layer ceramic capacitors have been used for high frequency decoupling application due to a lower overall impedance leading to fast current response. However, high parasitic inductance limits the application of these capacitors in ultra-high frequency domain. Thus, Multlayer Ceramic Capacitors (MLCCs) are placed close to the IC to improve circuit efficiency and reduce inductance. With next generation applications, the demand for frequency range has further increased which not only requires enhanced capacitor material but improved manufacturing techniques to limit the inductive path. Here, we demonstrate ALD of two different polymorphs of ultra-thin film lithium phosphorus oxynitride (LiPON) as an inorganic solid state electrolyte (SSE) for on chip capacitors for decoupling application. Both the LiPON capacitors shows an electric double layer behavior with a capacitance of 15 μF/cm 2 and a low leakage current (<20 nA/cm 2 ) at 2V. The LiPON shows EDLC behavior up to 10 kHz and beyond, both the polymorphs show an electrostatic behavior with a high dielectric constant (14). Furthermore, this dual frequency behavior along with low parasitic inductance and on chip integration allows for operation in extended frequency ranges.

25 ENERGY STORAGE↗

DOE OSTI2022

Simulation of the TAEs’ saturation phase in the Large Helical Device: MHD burst

Here, the aim of the present study is to analyze the saturation regime of the toroidal Alfven eigenmodes (TAE) in the Large Helical Device plasma, particularly the MHD burst. The linear and nonlinear evolution of the TAEs are simulated by the FAR3d code that uses a reduced MHD model for the thermal plasma coupled with a gyrofluid model for the energetic particle (EP) species. The linear simulations indicate the overlapping of 1/2–1/1, 2/3–2/4 and 3/5–3/6 TAEs in the inner-middle plasma region and frequency range of 45–75 kHz, triggered by EPs with an energy of T f = 45 keV and EP β = 0.022. The nonlinear simulations show that 2/3–2/4 and 3/4–3/5 TAEs are further destabilized due to the energy transfer from the 1/1–1/2 TAE, leading to broad TAE radial overlapping and triggering of the MHD burst. The energy of the 1/1–1/2 TAE is also nonlinearly transferred to the thermal plasma destabilizing the 0/0 and 0/1 modes, inducing the generation of shear flows and zonal currents, as well as large deformations in the thermal pressure and EP density radial profiles. The nonlinear simulation reproduces the same succession of instabilities and the same frequency range with respect to the experiment. The instability propagates outward during the bursting phase, showing a large decrease of the EP density profile between the middle-outer plasma, indicating the loss of part of the EP population that explains the decrease in the plasma heating efficiency observed during the MHD burst.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Relaxation dynamics of water in the vicinity of cellulose nanocrystals

Water molecules near cellulose nanocrystals (CNCs; produced via the sulfuric acid-catalyzed hydrolysis of wood pulp) are believed to relax slower than those in the bulk liquid, which may result in unique properties of CNC aqueous dispersions. Herein this study analyzed the polarization behavior of water molecules in CNC aqueous dispersions and other reference samples using a dielectric relaxation spectroscopy (DRS) technique in the microwave frequency range (0.2–20 GHz). As the CNC concentration increases, two slow relaxation components become prominent. The comparison with DRS data of aqueous dispersions of nanoporous silica, polyvinyl alcohol (PVA), and hairy CNC (HCNC) with amorphous chains protruding from both ends suggested that these slow relaxation modes of water near CNC surfaces cannot be attributed to direct hydrogen bonding interactions with the hydroxyl (OH) groups exposed and immobilized at the solid surface. Instead, they are similar to the water molecules interacting with OH groups attached to flexible polymer chains. Molecular dynamics (MD) simulations of the polarization behavior of water near the (110) facet of cellulose Iβ crystals confirmed that the interactions of water molecules with the cellulose crystal surface do not cause slower relaxations in the frequency range studied via the DRS. These results indicated that the CNC surface cannot be depicted with the crystallographic facets of cellulose Iβ; instead, it resembles a polymer-brush surface on which the short glucan residues or fragments of the strong acid-catalyzed hydrolysis process are swollen and extended into the aqueous phase.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2020

Rupture Dynamics Simulations of Shallow Crustal Earthquakes on Reverse Slip Faults

The main goal of this study was to perform dynamic rupture simulations in order constrain the characterization of kinematic rupture models implemented in techniques for simulating strong ground motion for crustal earthquakes. First, we investigated the rupture process of the 2008 Iwate-Miyagi Nairiku earthquake by developing a dynamic rupture model on a reverse fault using a trial-and-error technique that produced a slip distribution and near-fault ground motion that matched the recorded ones. The simulations were performed in the frequency range 0-2 Hz, using a 3D staggered grid finite-difference method and a linear slip weakening friction law. Constrained by the observed slip distribution and consistent with dynamic rupture models, the derived kinematic rupture model of the Iwate-Miyagi Nairiku earthquake contains areas with relatively large slip rate, representing strong motion generation areas, set against lower amplitude heterogeneous background slip, and a relatively low slip rate in the weak zone of the top-most crust (upper 3km). Second, we performed rupture dynamics modeling to constrain shallow slip characterization in rupture models for strike-slip crustal earthquakes. The objective was to establish general rules about the characterization of slip rate function and slip at shallow depths and in the strong motion generation areas (SMGAs). The simulations of spontaneous rupture were performed in the frequency range 0-2.0Hz, using a 3D staggered-grid finite-difference method and a layer over half-space 1D crustal velocity model with a minimum shear-wave velocity of 2.8 km/s. In order to account for changes in material ductility and reduction of stress drop, observed in the shallow crust (upper 3-5 km), and the transition from ductile state to brittle state in the upper seismogenic zone, in our stress models we included a shallow weak zone (<4km). In this zone the stress drop was set to zero at the free surface and gradually increased with depth, while the slip weakening distance was set to 75 cm at the free surface and decreased to 50 cm at the base of the weak zone. As in the case of reverse faulting during the Iwate-Miyagi Nairiku earthquake, from these computations we found a systematic change in the shape of the slip-rate function, from Kostrov-type in the deeper part of the fault to a more symmetric cosine-type in the upper few kilometers, near the free-surface. Moreover, the average slip duration in the weak zone, with respect to slip duration in the deeper parts of the fault, increases by at most a factor of 1.5. We found a systematic and gradual change in the shape of the slip-rate function from Kostrov-type in the asperity areas (SMGAs), to more symmetric cosine-type in the upper few km near the free-surface, on the long period motion generation area (LMGA). The effective rise time in the LMGA, with respect to that in the SMGAs, increases by at most a factor of 2. Effective rise time is the time difference between the time at which the slip rate drops to a level that is equal to 25% of its peak and the onset time of the signal. In addition, the slip in the LMGA located above the SMGAs is almost the same as the one in the SMGAs, and about 1.5 times larger than the average slip.

58 GEOSCIENCES↗

DOE OSTI2022

Progress in ITER ECE diagnostic design and integration

The ITER electron cyclotron emission (ECE) diagnostic system has primary roles in providing measurements of the core electron temperature profile and the electron temperature fluctuation associated with the neoclassical tearing modes. The ITER ECE system includes a radial and oblique line-of-sight. Four 43-meter long low-loss transmission lines (TLs) are designed to transmit millimeter wave power in the frequency range of 70–1000 GHz in both X- and O-mode polarization from the port plug to the ECE instrumentation room in the diagnostic building. The measurement instrumentation includes two Fourier transform spectrometer (FTS) systems and two radiometer systems. The Indian Domestic Agency (IN-DA) and United States Domestic Agency share the responsibility. The IN-DA scope excluding instrumentation and control has passed its preliminary design review and is progressing towards the final design review (FDR). In parallel, the diagnostic integration in different areas is ongoing. Furthermore, several captive components for the TLs have passed FDR and will be manufactured for installation in the tokamak building soon. A peer review meeting has been held on the prototype hot calibration source, and its integration and new thermal analysis in the diagnostic shield module are continuing. A prototype TL is being tested. A prototype polarizing Martin-Puplett type FTS, operating in the frequency range 70–1000 GHz, features an in-vacuo fast scanning mechanism and a cryo-cooled dual-channel THz detector system. Its performance has been assessed in detail against ITER requirements.

47 OTHER INSTRUMENTATION↗

DOE OSTI2020

Uncertainties in turbulent statistics and fluxes of CO2 associated with density effect corrections

Density effect corrections (DEC) are applied to adjust raw CO2 fluxes measured by eddy covariance (EC) systems with open-path gas analyzers. DEC is also required for adjusting the measured CO2 concentration fluctuations to obtain the adjusted CO2 for analyzing turbulent statistics or quantifying fluxes. However, our data show that the power spectra of the DEC-adjusted CO2 are distorted in the high frequency range, as compared with the corresponding spectra of temperature and water vapor density. This contradicts the similarity behavior of scalars, as suggested by Monin-Obukhov similarity theory. It is demonstrated that such a distortion is caused by the DEC-induced spikes in the DEC-adjusted CO2, altering turbulent statistics of CO2 and scalar similarity between CO2 and other scalars. Our results suggest that CO2 fluxes are overestimated by applying DEC especially under high Bowen ratio conditions, potentially leading to substantial uncertainties in long-term ecosystem carbon exchange in dry regions.

Gao, Zhongming↗

DOE OSTI2023

Measurement of Dielectric Loss in Silicon Nitride at Centimeter and Millimeter Wavelengths

This work presents a suite of measurement techniques for characterizing the dielectric loss tangent across a wide frequency range from similar to 1 GHz to 150 GHz using the same test chip. In the first method, we fit data from a microwave resonator at different temperatures to a model that captures the two-level system (TLS) response to extract and characterize both the real and imaginary components of the dielectric loss. The inverse of the internal quality factor is a second measure of the overall loss of the resonator, where TLS loss through the dielectric material is typically the dominant source. The third technique is a differential optical measurement at 150 GHz. The same antenna feeds two microstrip lines with different lengths that terminate in two microwave kinetic inductance detectors (MKIDs). The difference in the detector response is used to estimate the loss per unit length of the microstrip line. Our results suggest a larger loss for SiNx at 150 GHz of tan delta similar to 4 x 10(-3) compared to 2.0 x 10(-3) and greater than or similar to 1 x 10(-3) measured at similar to 1 GHz using the other two methods. These measurement techniques can be applied to other dielectrics by adjusting the microstrip lengths to provide enough optical efficiency contrast and other mm/sub-mm frequency ranges by tuning the antenna and feedhorn accordingly.

Dielectrics loss↗