Search NASA⌕ Search

SEARCH · Search NASA

Results for “Processing reliability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Design for Reliability (DfR) in Space Life Support

The engineering process of Design for Reliability (DfR) is well established in the automotive and aerospace industries. DfR should be useful in the future development of space life support systems. DfR is a sequence of tasks that develop system requirements and plan reliability analysis and testing. First and fundamentally, the reliability requirement is defined. Next the system reliability model is developed, often using a reliability block diagram. The overall system reliability requirement is allocated to the subsystems and an estimate of the attainable reliability is made. This expected reliability can be improved by simplifying the design by removing components or by replacing less reliable components. Improving reliability can require difficult compromises, such as reducing performance requirements, increasing budget, or extending testing. The actual system reliability can be determined only by testing, which should continue long enough to provide the required confidence in the measured value. New systems often have unexpected design errors that cause failures in early testing. The usual reliability improvement process of testing, finding the failure modes, and redesigning to remove them reduces the failure rate and is referred to as “reliability growth.” After redesign has been completed, the system should be further tested to determine the actual achieved reliability more accurately. If the final system failure rate is too high, redundant systems can be used to improve overall operational reliability. Adding redundancy simply to increase the one- or two-fault tolerance metric may sometimes reduce reliability. Reliability can be improved in three ways: redesigning the system to include more reliable subsystems and components, reliability growth testing and failure mode removal, and by using parallel redundant systems. DfR should combine these approaches to achieve the required reliability while managing performance, cost, and schedule.

Reliability↗
DOE OSTI2026

Interconnect: Cooperative Research and Development Final Report, CRADA Number CRD-13-00507 (Project 4)

This CRADA modification involves analyses on a variety of CdTe-PV related materials, test structures, solar cells, and modules produced at FSLR and/or NLR and adds analysis related to module degradation and reliability. Materials will be provided by FSLR, NLR, and/or by interleaving FSLR and NLR layers and processes. Module reliability activities will include technical risk assessment, materials characterization, module and test structure characterization, modeling, accelerated test development, and outdoor testing.

14 SOLAR ENERGY↗
NASA NTRS1991

An error bound for instantaneous coverage

An error bound is derived for a reliability model approximation method. The approximation method is appropriate for the semi-Markov models of reconfigurable systems that are designed to achieve extremely high reliability. The semi-Markov models of these system are complex, and a significant amount of their complexity arises from the detailed descriptions of the reconfiguration processes. The reliability model approximation method consists of replacing a detailed description of a reconfiguration process with the probabilities of the possible outcomes of the reconfiguration process. These probabilities are included in the model as instantaneous jumps from the fault-occurrence state. Since little time is spent in the reconfiguration states, instantaneous jumps are a close approximation to the original model. This approximation procedure is shown to produce an overestimation for the probability of system failure, and an error bound is derived for this overestimation.

White, Allan L.↗
NASA NTRS2013

Supersonic Retropulsion Surface Preparation of Carbon Fiber Reinforced Epoxy Composites for Adhesive Bonding

Surface preparation is widely recognized as a key step to producing robust and predictable bonds in a precise and reproducible manner. Standard surface preparation techniques, including grit blasting, manual abrasion, and peel ply, can lack precision and reproducibility, which can lead to variation in surface properties and subsequent bonding performance. The use of a laser to ablate composite surface resin can provide an efficient, precise, and reproducible means of preparing composite surfaces for adhesive bonding. Advantages include elimination of physical waste (i.e., grit media and sacrificial peel ply layers that ultimately require disposal), reduction in process variability due to increased precision (e.g. increased reproducibility), and automation of surface preparation, all of which improve reliability and process control. This paper describes a Nd:YAG laser surface preparation technique for composite substrates and the mechanical performance and failure modes of bonded laminates thus prepared. Additionally, bonded specimens were aged in a hot, wet environment for approximately one year and subsequently mechanically tested. The results of a one year hygrothermal aging study will be presented.

Palmieri, Frank L.↗
NASA NTRS2002

Reliability Methods for Shield Design Process

Providing protection against the hazards of space radiation is a major challenge to the exploration and development of space. The great cost of added radiation shielding is a potential limiting factor in deep space operations. In this enabling technology, we have developed methods for optimized shield design over multi-segmented missions involving multiple work and living areas in the transport and duty phase of space missions. The total shield mass over all pieces of equipment and habitats is optimized subject to career dose and dose rate constraints. An important component of this technology is the estimation of two most commonly identified uncertainties in radiation shield design, the shielding properties of materials used and the understanding of the biological response of the astronaut to the radiation leaking through the materials into the living space. The largest uncertainty, of course, is in the biological response to especially high charge and energy (HZE) ions of the galactic cosmic rays. These uncertainties are blended with the optimization design procedure to formulate reliability-based methods for shield design processes. The details of the methods will be discussed.

Tripathi, R. K.↗
NASA NTRS2008

James Webb Space Telescope - L2 Communications for Science Data Processing

JWST is the first NASA mission at the second Lagrange point (L2) to identify the need for data rates higher than 10 megabits per second (Mbps). JWST will produce approximately 235 Gigabits of science data every day that will be downlinked to the Deep Space Network (DSN). To get the data rates desired required moving away from X-band frequencies to Ka-band frequencies. To accomplish this transition, the DSN is upgrading its infrastructure. This new range of frequencies are becoming the new standard for high data rate science missions at L2. With the new frequency range, the issues of alternatives antenna deployment, off nominal scenarios, NASA implementation of the Ka-band 26 GHz, and navigation requirements will be discussed in this paper. JWST is also using Consultative Committee for Space Data Systems (CCSDS) standard process for reliable file transfer using CCSDS File Delivery Protocol (CFDP). For JWST the use of the CFDP protocol provides level zero processing at the DSN site. This paper will address NASA implementations of Ground Stations in support of Ka-band 26 GHz and lesson learned from implementing a file base (CFDP) protocol operational system.

Johns, Alan↗
NASA NTRSDate not supplied

Reliability Growth Modeling and Testing

Reliability growth has been modelled as an exponential decline in the cumulative failure rate that continues indefinitely as long as testing continues. Contrary to this, most reliability growth data show a brief high initial failure rate due to infant mortality followed by a long period of constant low failure rate. A two part failure rate model with an initial exponential decline followed by a constant failure rate usually fits the data and provides a more realistic description of reliability growth. The reliability growth process consists of testing, experiencing failures, finding the failure causes, and redesigning the system to remove them. The cost of reliability growth increases with the number of inherent failure modes and the time needed for them to occur and be removed. The failure modes with the lower failure rates will tend to occur later, as their Mean Time Before Failure (MTBF) is the inverse of the failure rate. Reliability growth testing has diminishing returns, since it takes longer to find and remove the less probable failures.This paper first discusses the reliability bathtub curve and then explains that reliability growth is produced by testing, identifying failure causes, and designing to remove them. A simple model of reliability growth is introduced, with a brief group of early failures followed by a constant failure rate. The cumulative failure rate n(t)/t can decline as rapidly as1/t or t-1butdeclines more slowly if additiona lfailures occur. The 56-failure Crow data seti s used to demonstrate the two-phase model of reliability growth followed by a constant failure rate. 13 additional data sets are modeled, with 9 of the 14 data sets showing reliability growth approximately as n(t)/t =1/t or t-1and substantial final failure rates. The model fits most of the data sets, but 4of the 14 show no reliability growth. The reliability growth period typically includes six failures and extends one-quarter or half the total test time. As reliability growth testing continues, the cumulative failure rate should be tracked to estimate the reliability growth exponent and the final failure rate.

reliability growth modeling↗
NASA NTRSDate not supplied

Modeling Reliability Growth

Reliability growth has been modelled as an exponential decline in the cumulative failure rate that continues indefinitely as long as testing continues. Contrary to this, most reliability growth data show a brief high initial failure rate due to infant mortality followed by a long period of constant low failure rate. A two part failure rate model with an initial exponential decline followed by a constant failure rate usually fits the data and provides a more realistic description of reliability growth. The reliability growth process consists of testing, experiencing failures, finding the failure causes, and redesigning the system to remove them. The cost of reliability growth increases with the number of inherent failure modes and the time needed for them to occur and be removed. The failure modes with the lower failure rates will tend to occur later, as their Mean Time Before Failure (MTBF) is the inverse of the failure rate. Reliability growth testing has diminishing returns, since it takes longer to find and remove the less probable failures.This paper first discusses the reliability bathtub curve and then explains that reliability growth is produced by testing, identifying failure causes, and designing to remove them. A simple model of reliability growth is introduced, with a brief group of early failures followed by a constant failure rate. The cumulative failure rate n(t)/t can decline as rapidly as1/t or t-1butdeclines more slowly if additiona lfailures occur. The 56-failure Crow data seti s used to demonstrate the two-phase model of reliability growth followed by a constant failure rate. 13 additional data sets are modeled, with 9 of the 14 data sets showing reliability growth approximately as n(t)/t =1/t or t-1and substantial final failure rates. The model fits most of the data sets, but 4of the 14 show no reliability growth. The reliability growth period typically includes six failures and extends one-quarter or half the total test time. As reliability growth testing continues, the cumulative failure rate should be tracked to estimate the reliability growth exponent and the final failure rate.

reliability growth modeling↗
NASA NTRS2012

Scaled CMOS Reliability and Considerations for Spacecraft Systems: Bottom-Up and Top-Down Perspective

New space missions will increasingly rely on more advanced technologies because of system requirements for higher performance, particularly in instruments and high-speed processing. Component-level reliability challenges with scaled CMOS in spacecraft systems from a bottom-up perspective have been presented. Fundamental Front-end and Back-end processing reliability issues with more aggressively scaled parts have been discussed. Effective thermal management from system-level to the componentlevel (top-down) is a key element in overall design of reliable systems. Thermal management in space systems must consider a wide range of issues, including thermal loading of many different components, and frequent temperature cycling of some systems. Both perspectives (top-down and bottom-up) play a large role in robust, reliable spacecraft system design.

Scaled CMOS↗
NASA NTRS1985

Dendritic web-type solar cell mini-modules

Twenty-five minimodules composed of dendritic web solar cells with nominal glass size of 12 by 40 cm were provided for study. The modules were identical with respect to design, materials, and manufacturing and assembly processes to full scale modules. The modules were also electrically functional. These minimodules were fabricated to provide test vehicle for environmental testing and to assess reliability of process and design procedures. The module design and performance are outlined.

Campbell, R. B.↗
NASA NTRS1987

Computer Reliability

Using a NASA developed program, Dr. J. Walter Bond is creating a course in computer reliability modeling. The course will examine three different computer programs, one of them NASA's Care III, the others UCLA's Aries 78 and Aries 82. All three are designed to help estimate the reliability of complex, redundant, fault tolerant system. In computer design, software of this kind can predict or model the effects of various hardware or software failures, a process called reliability modeling.

Source record↗
NASA NTRS1978

Evaluation of ceramics for stator application: Gas turbine engine report

Current ceramic materials, component fabrication processes, and reliability prediction capability for ceramic stators in an automotive gas turbine engine environment are assessed. Simulated engine duty cycle testing of stators conducted at temperatures up to 1093 C is discussed. Materials evaluated are SiC and Si3N4 fabricated from two near-net-shape processes: slip casting and injection molding. Stators for durability cycle evaluation and test specimens for material property characterization, and reliability prediction model prepared to predict stator performance in the simulated engine environment are considered. The status and description of the work performed for the reliability prediction modeling, stator fabrication, material property characterization, and ceramic stator evaluation efforts are reported.

Trela, W.↗
DOE OSTI2025

Uncertainty improvement of 22 Na based radioactive tracer dilution for determining total mass of pyroprocessing molten salt systems by 154 Eu removal

To determine the total salt mass of the molten salt systems for pyroprocessing spent nuclear fuels, a 22 Na based radioactive tracer dilution was studied in Idaho National Laboratory in recent years. This 22 Na based RTD technique was deemed feasible, but due to the gamma energy peak of 22 Na coinciding with one of the energy peaks of 154 Eu radioisotope in the molten salt, the uncertainty of the 22 Na radioactivity in the 22 Na-spiked salt samples was quite high. To improve the uncertainty of the 22 Na based RTD technique, we proposed to chemically remove the 154 Eu of the salt samples by DGA resin for gamma spectroscopy. The effectiveness of removing 154 Eu on uncertainty improvement was evaluated. Furthermore, it was found that (1) the 154 Eu fission product effect on the uncertainty and detection limit can be effectively eliminated by chemically removing the 154 Eu during the salt sample preparation and (2) the uncertainty of 22 Na radioactivity in the salt samples for electrorefining was significantly improved from 13% to 2%, showing the potential of practical engineering application of 22 Na based RTD as a safeguards technique for molten salt systems for pyroprocessing spent nuclear fuels.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1983

Structural control research and experiments at NASA/LaRC

The advances made in the area of structural dynamics and control using the flexible beam facility at the NASA Langley Research Center are surveyed. Spectral attention is given to the progress in adaptive control and reliability improvements using advanced control concepts. Both theoretical and experimental results are given to delineate the nature of the work being undertaken. With regard to adaptive control, emphasis is placed on parameter and system identification and on comparisons between competing on-line algorithms. In addition, results are presented for on-line modal control laws that are interfaced to a parameter identification scheme. This gives an on-line distributed adaptive control system. With regard to reliability, a design process is outlined that incorporates reliability over the design mission life.

Montgomery, R. C.↗
NASA NTRS1996

A Single-Block TRL Test Fixture for the Cryogenic Characterization of Planar Microwave Components

The High-Temperature-Superconductivity (HTS) group of the RF Technology Branch, Space Electronics Division, is actively involved in the fabrication and cryogenic characterization of planar microwave components for space applications. This process requires fast, reliable, and accurate measurement techniques not readily available. A new calibration standard/test fixture that enhances the integrity and reliability of the component characterization process has been developed. The fixture consists of 50 omega thru, reflect, delay, and device under test gold lines etched onto a 254 microns (0.010 in) thick alumina substrate. The Thru-Reflect-Line (TRL) fixture was tested at room temperature using a 30 omega, 7.62 mm (300 mil) long, gold line as a known standard. Good agreement between the experimental data and the data modelled using Sonnet's em(C) software was obtained for both the return (S(sub 11)) and insertion (S( 21)) losses. A gold two-pole bandpass filter with a 7.3 GHz center frequency was used as our Device Under Test (DUT), and the results compared with those obtained using a Short-Open-Load-Thru (SOLT) calibration technique.

Mejia, M.↗
NASA NTRS2024

Evaluation of Aluminum Polymer Capacitors for Space Applications

Layered aluminum polymer capacitors (APC) may be viable replacements to currently used chip tantalum capacitors due to their lower ESR, weight, and smaller size. So far, there is a lack of information regarding the reliability of these parts. Available technical literature is mostly related to the effect of humidity. Although APCs have a limited moisture resistance, it may be contained to the level sufficient for space applications. This work analyzes construction and characteristics of seven types of commercial APCs manufactured by four vendors and rated to voltages from 6.3 to 35 V were analyzed. Their reliability under environmental stresses and highly accelerated life tests was assessed in the range of temperatures and voltages to determine reliability acceleration factors. For this purpose, characteristics of the parts, including breakdown voltages, the level of anomalous charging currents (ACC), capacitance, DF, ESR and leakage currents were measured in the process of storage at high-temperatures (from 100 to 150 °C) and high humidity at 85 °C. Monitored highly accelerated life tests have been carried out at temperatures of 85 °C and 125 °C and voltages varying from 1.2 to 1.9 times the rated voltage. Degradation processes and reliability of APCs have been compared to polymer tantalum capacitors.

Alexander A Teverovsky↗
NASA NTRS2013

Autonomous Control of Space Nuclear Reactors

Nuclear reactors to support future robotic and manned missions impose new and innovative technological requirements for their control and protection instrumentation. Long-duration surface missions necessitate reliable autonomous operation, and manned missions impose added requirements for failsafe reactor protection. There is a need for an advanced instrumentation and control system for space-nuclear reactors that addresses both aspects of autonomous operation and safety. The Reactor Instrumentation and Control System (RICS) consists of two functionally independent systems: the Reactor Protection System (RPS) and the Supervision and Control System (SCS). Through these two systems, the RICS both supervises and controls a nuclear reactor during normal operational states, as well as monitors the operation of the reactor and, upon sensing a system anomaly, automatically takes the appropriate actions to prevent an unsafe or potentially unsafe condition from occurring. The RPS encompasses all electrical and mechanical devices and circuitry, from sensors to actuation device output terminals. The SCS contains a comprehensive data acquisition system to measure continuously different groups of variables consisting of primary measurement elements, transmitters, or conditioning modules. These reactor control variables can be categorized into two groups: those directly related to the behavior of the core (known as nuclear variables) and those related to secondary systems (known as process variables). Reliable closed-loop reactor control is achieved by processing the acquired variables and actuating the appropriate device drivers to maintain the reactor in a safe operating state. The SCS must prevent a deviation from the reactor nominal conditions by managing limitation functions in order to avoid RPS actions. The RICS has four identical redundancies that comply with physical separation, electrical isolation, and functional independence. This architecture complies with the safety requirements of a nuclear reactor and provides high availability to the host system. The RICS is intended to interface with a host computer (the computer of the spacecraft where the reactor is mounted). The RICS leverages the safety features inherent in Earth-based reactors and also integrates the wide range neutron detector (WRND). A neutron detector provides the input that allows the RICS to do its job. The RICS is based on proven technology currently in use at a nuclear research facility. In its most basic form, the RICS is a ruggedized, compact data-acquisition and control system that could be adapted to support a wide variety of harsh environments. As such, the RICS could be a useful instrument outside the scope of a nuclear reactor, including military applications where failsafe data acquisition and control is required with stringent size, weight, and power constraints.

Merk, John↗