SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The following technical developments are described: (1) a reliable 183 GHz subharmonic mixer, (2) a precision noise figure test setup, (3) the successful deposition of SiO2 on a noncontacting backshort, and (4) sturdier whisker points used for diode contacting.
The diffraction of spark-discharge-produced sound waves produced by a half circular cylinder covered with absorbing material is investigated theoretically and experimentally. The test bench setup and the measurement instrumentation and procedure are described; the derivation of an analytical model on the basis of the matched asymptotic expansion theory of Pierce (1981) is outlined; and the results are compared in graphs. Good general agreement is obtained, except in the deep shadow of the obstacle, where the theory underpredicts the magnitude of the received pulse. This discrepancy is tentatively attributed to the creeping-wave mechanism described by Pierce.
We theoretically investigate the influence of chiral Casimir-Polder (CP) forces in Talbot-Lau interferometry, based on three nanomechanical gratings. We study scenarios where the second grating is either directly written into a chiral material or where the nanomask is coated with chiral substances. We show requirements for probing enantiospecific effects in matter-wave interferometry in the transmission signal and the interference fringe visibility, which depend on the de Broglie wavelength and the molecular chirality. The proposed setup is particularly sensitive to CP forces in the nonretarded regime where chiral effects can be comparable in magnitude to their electric and magnetic counterparts. While the first and third gratings do not change the phase of the matter wave, applying a coating of chiral substances to them enhances the instrument's chiral selectivity. Published by the American Physical Society 2024
As rotating detonation engines (RDEs) progress in maturity, the importance of monitoring advancements toward development of active control becomes more critical. Experimental RDE data processing at time scales which satisfy real-time diagnostics will likely require the use of machine learning. This study aims to develop and deploy a novel real-time monitoring technique capable of determining detonation wave number, direction, frequency, and individual wave speeds throughout experimental RDE operational windows. To do so, the diagnostic integrates image classification by a convolutional neural network (CNN) and ionization current signal analysis. Wave mode identification through single-image CNN classification bypasses the need to evaluate sequential images and offers instantaneous identification of the wave mode present in the RDE annulus. Here, real-time processing speeds are achieved due to low data volumes required by the methodology, namely one short-exposure image and a short window of sensor data to generate each diagnostic output. The diagnostic acquires live data using a modified experimental setup alongside Pylon and PyDAQmx libraries within a python data acquisition environment. Lab-deployed diagnostic results are presented across varying wave modes, operating conditions, and data quality, currently executed at 3–4 Hz with a variety of iteration speed optimization options to be considered as future work. These speeds exceed that of conventional techniques and offer a proven structure for real-time RDE monitoring. The demonstrated ability to analyze detonation wave presence and behavior during RDE operation will certainly play a vital role in the development of RDE active control, necessary for RDE technology maturation toward industrial integration.
Electrode–electrolyte interfaces are of critical importance in several fields, including renewable energy, corrosion, and environmental chemistry. However, investigating these interfaces under operational conditions poses considerable challenges due to the limitations of the instrumentation employed. While recent advancements in in situ and operando techniques have enhanced our comprehension of the steady-state properties of solid-liquid interfaces, the dynamic behaviors of these systems remain inadequately explored. This study introduces a time-resolved X-ray photoelectron spectroscopy (XPS) technique designed to capture transient reaction intermediates and charging dynamics at electrified interfaces. The presented proof-of-principle study demonstrates that electrochemical processes, represented by an equivalent electrical circuit (EEC) model, can be probed and understood using square wave voltage pulses of a potentiostat synchronized to the modified data acquisition of an XPS setup. This method offers a valuable alternative to traditional pump–probe techniques, facilitating the investigation of a broader range of electrochemical systems. A dedicated software package for analyzing time- and energy-resolved XPS with a focus on extracting parameters of the EEC is geared towards benchmarking different EECs in future real-world electrochemical experiments.
This study conducted integrated experiments and computational modeling to investigate the speeds of a developing shock within granular salt and analyzed the effect of various impact velocities up to 245 m/s. Experiments were conducted on table salt utilizing a novel setup with a considerable bore length for the sample, enabling visualization of a moving shock wave. Experimental analysis using particle image velocimetry enabled the characterization of shock velocity and particle velocity histories. Mesoscale simulations further enabled advanced analysis of the shock wave’s substructure. In simulations, the shock front’s precursor was shown to have a heterogeneous nature, which is usually modeled as uniform in continuum analyses. The presence of force chains results in a spread out of the shock precursor over a greater ramp distance. With increasing impact velocity, the shock front thickness reduces, and the precursor of the shock front becomes less heterogeneous. Furthermore, mesoscale modeling suggests the formation of force chains behind the shock front, even under the conditions of weak shock. This study presents novel mesoscale simulation results on salt corroborated with data from experiments, thereby characterizing the compaction front speeds in the weak shock regime.
Frequency-modulation spectroscopy (FMS) is generally suited to code-division multiplexing, and we demonstrate that capacity in a form of continuous-wave LIDAR, utilizing a sharp CO 2 absorption transition at 1.6 µm in simple ranging setups. The approach retains the advantages of FMS, including coherent detection and good rejection of broad absorption backgrounds. Extensions of this multiplexed approach to the continuous, simultaneous detection of several transitions would come by transmitting an encoded combination of frequency-modulated carriers, each tuned to detect a unique absorption transition. Signal analysis at the receiver involves a simple process of de-multiplexing that, in a general application, reveals targets at various distances and the absorption-related FMS signals in between.
Collaborative effort between AquaHarmonics, Sandia National Laboratories (SNL), and the National Renewable Energy Laboratory (NREL) to revise and validate Aquaharmonics' full wave to wire model, allowing for reduced uncertainty and increased understanding of design requirements of a utility scale wave energy converter (WEC). SNL and NREL in collaboration with AquaHarmonics, will set up and run WEC Simulator (WEC-Sim) models of the AquaHarmonics WEC, building off past model developments for inclusion of custom PTO (power take-off) dynamics. The intent is to review, update, and verify or validate a new WEC-Sim model against wave tank experimental data. Furthermore, the WEC-Sim model will be coupled to an energy storage system model to better understand the wave-to-wire functionality. This data set is described in the "Test Log" excel file. Please refer to that document for details on each specific test date/time, constraint parameters and model hardware setup details. Sim model can be found in the associated MHKDR link below.
This study applied the nonlinear ultrasonic method, second harmonic generation, to precisely estimate the state of charge (SoC) in lithium-ion batteries. The second harmonic of the longitudinal wave is generated on a pouch cell battery at 5 MHz with a through-transmission setup. The relative nonlinear parameter β' is determined by analyzing the amplitudes at the fundamental and second harmonic frequencies. To enhance the nonlinear parameter's measurement accuracy, multiple excitation amplitudes are employed. Two separate charge/discharge tests (four-cycle and eight-cycle) are conducted on the battery at a rate of C/10. The nonlinear parameter is measured periodically during the charge/discharge process, and temperature compensation is applied to the measurement. The correlation curves between the nonlinear parameter and the actual SoC align well for the four-cycle and eight-cycle tests, and a robust linear relationship is observed for both correlation curves. A linear model and a second-order polynomial model are applied to fit the correlation using all data points from both tests. The two models are employed to validate the SoC prediction on a second battery by using a four-cycle test. Furthermore, the results indicate that both models can predict the SoC with an accuracy of approximately 3%, whereas the polynomial model demonstrates smaller errors in the regions near 0% and 100% SoC. Therefore, the nonlinear parameter β', measured through the second harmonic generation, can effectively predict lithium-ion battery SoC with an accuracy of less than 3%.
Foliage penetration (FOPEN) radar at lower frequencies (VHF, UHF) is a well-studied area with many contributions. However, there is growing interest in using higher Ku-band frequencies (12-18 GHz) for FOPEN. Specifically, the reduced wavelength sizes provide some key saliencies for developing more optimized detection solutions. The disadvantage is that exploiting Ku-band for FOPEN is complicated because higher frequencies have pronounced scattering effects due to their smaller wavelengths. A methodology h as been developed to model and simulate FOPEN problems that characterize the phenomenology of Ku-band electromagnetic ( EM ) wave transmissions through moderate foliage. The details of this research (i.e. the realistic tree models, simulation setup and results) are documented in multiple reports. The main focus of this report is to describe the preliminary validation and verification of Altair FEKO, the computational EM (CEM) software used for this research, as well as present a simplified symmetrical tree model and an introductory CAD tree model.
Dispersion characteristics of cyclotron-harmonic waves propagating on a neutralized spiraling electron beam immersed in a uniform axial magnetic field are studied experimentally. The experimental setup consisted of a vacuum system, an electron-gun corkscrew assembly which produces a 110-eV beam with the desired delta-function velocity distribution, a measurement region where a microwave signal is injected onto the beam to measure wavelengths, and a velocity analyzer for measuring the axial electron velocity. Results of wavelength measurements made at beam currents of 0.15, 1.0, and 2.0 mA are compared with calculated values, and undesirable effects produced by increasing the beam current are discussed. It is concluded that a suitable electron beam for studies of cyclotron-harmonic waves can be generated by the corkscrew device.
Accurate characterization of two ultrashort laser pulses is of great interest in many ultrafast pump-probe experiments. We demonstrate a method based on four-wave mixing (FWM) in a gas which could be easily implemented into many existing pump-probe setups with minimal modifications for accurate, in situ characterization of both unknown pulses. This technique is tested on pairs of unknown pulses at wavelengths of 400/800 nm, and 266/400 nm. We measured the spectrogram of the pulse generated through FWM of the two unknown pulses by scanning the delay between two unknown pulses. The retrieval algorithm converges to accurately predict the intensity and the phase profiles of both unknown pulses with a trace error of < 1% and the accuracy is verified using an independent pulse characterization device.
Our major goal for the project was to make magnetic field and plasma density fluctuation measurements using identical diagnostic and acquisition setups on two different laboratory-based turbulent plasma devices: SSX at Swarthmore College and a new plasma source in development at Bryn Mawr College (BMX). We used single-point correlation and k-filtering metrics using these experimental measurements. These metrics were compared to kinetic simulations of the experimental environments in order to determine wave mode content of the laboratory turbulence.
The electron plasma wave feature (EPW) in the time-resolved Thomson scattering spectrum is used to obtain the local electron density in imploding high energy density gas-puff z-pinch plasmas. The optical setup was optimized to allow the relatively weak EPW feature obtained from 1 MA imploding neon gas-puff z-pinches to be seen above the continuum emission as well as the brighter ion acoustic wave (IAW) feature. Using a frequency-doubled Nd:YLF laser (E = 10 J, λ = 526.5 nm, Δt= 2.3 ns, spot size ~ 250 μm) and two visible light streak cameras, we determined the average electron density in the imploding plasma sheath 40 ns prior to stagnation to be n e = 2.5 × 10 18 /cm 3 . At pinch time, it reached n e = 1.7 × 10 19 /cm 3 . Here, the electron temperature during implosion measured via the IAW (approximately 50 eV) was four times lower than the implosion electron temperature measured via the EPW (approximately 200 eV), assuming that neither feature is affected by turbulent fluctuations in the plasma. In order for the electron temperatures inferred from the EPW and IAW spectral features to be self-consistent, we find that it is necessary to include velocity fluctuations in the analysis of the IAW feature peaks and corresponding density fluctuation in the peak widths of the EPW feature.
The accurate characterization of the dynamic response of liquid jets to transient detonation wave passage is crucial for optimizing and modeling liquid-fueled rotating detonation combustors. To address this need, we have developed an optically accessible rocket RDE (RP-RDE), which utilizes liquid RP-1 and gaseous oxygen as propellants and operates at elevated pressures. The experimental setup features optical access from the oxidizer injection plenum to the combustor exit, allowing for detailed characterization of injection, mixing, and combustion processes and their impact on the detonation wave structure. To design and develop the liquid injection scheme for the RP-RDE test article, we employed a combined experimental and numerical approach that included cold-flow simulations. Our aim was to optimize the liquid injection process and ensure that the resulting fuel-oxidizer mixture is homogeneous and stable. To this end, high-speed optical imaging will be employed to provide qualitative visualization of the liquid and gaseous phases of the propellant as well as the local heat release during detonation wave propagation through the non-premixed medium. This work will provide critical insights into the behavior of the transient detonation waves in more relevant rocket conditions, which is essential for the optimization and modeling of rotating detonation combustors.
Numerous analytical and theoretical studies of the behavior of leaky Lamb waves (LLW) in composite materials were documented in the literature. One of the key issues that are constraining the application of this method as a practical tool is the amount of data that needs to be acquired and the slow process that is involved with such experiments. Recently, a methodology that allows quasi real-time acquisition of LLW dispersion data was developed. At each angle of incidence the reflection spectrum is available in real time from the experimental setup and it can be used for rapid detection of the defects. This technique can be used to rapidly acquire the various plate wave modes along various angles of incidence for the characterization of the material elastic properties. The experimental method and data acquisition technique will be described in this paper. Experimental data was used to examine a series of flaws including porosity and delaminations and demonstrated the efficiency of the developed technique.
Designing and validating controllers for connected and automated vehicles to enhance traffic flow presents significant challenges, from the complexity of replicating real-world stop-and-go traffic dynamics in simulation, to the intricacies involved in transitioning from simulation to actual deployment. In this work, we present a full pipeline from data collection to controller deployment. Specifically, we collect 772 km of driving data from the I-24 in Tennessee, and use it to build a one-lane simulator, placing simulated vehicles behind real-world trajectories. Using policy-gradient methods with an asymmetric critic, we improve fuel efficiency by over 10% when simulating congested scenarios. Our comprehensive approach includes reinforcement learning for controller training, software verification, hardware validation and setup, and navigating various sim-to-real challenges. Furthermore, we analyze the controller's behavior and wave-smoothing properties, and deploy it on four Toyota Rav4’s in a real-world validation experiment on the I-24. Lastly, we release the driving dataset, the simulator and the trained controller, to enable future benchmarking and controller design.
A full wave space domain integral equation (SDIE) analysis of coplanar waveguide (CPW) two port discontinuities is presented. An experimental setup to measure the S-parameters of such discontinuities is described. Experimental and theoretical results for CPW realizations of pass-band and stop-band filters are presented. The S-parameters of such structures are plotted in the frequency range 5 to 25 GHz.