SEARCH · Search NASA

Results for “ZIRCONIUM ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Device for steam cladding oxidation testing at TREAT

To compare the chemical degradation of conventional zirconium alloy (Zry) cladding to advance silicon carbide (SiC) cladding in a post loss of coolant accident (LOCA) environment, new nuclear testing capabilities are necessary. The Transient Reactor Test (TREAT) Facility at Idaho National Laboratory (INL) has matured its transient fuel testing capabilities since its 2017 restart. The most recent experiment architecture is the Transient Water Irradiation System in TREAT (TWIST), which is designed to support qualification of accident tolerant fuels in light water reactors. INL has designed and analyzed a natural circulation steam flow modification for TWIST to produce prototypic conditions of cladding oxidation. The in-situ device will be electrically heated to drive natural circulation. Moreover, the SiC cladding requires heating above 1700 °C to observe failure, thus internal prototypic nuclear heating with radiation effects will be used. Thermal hydraulic analysis with RELAP5-3D (Reactor Excursion and Leak Analysis Program) estimated steam fluxes greater than 50 mg cm −2 s −1 can be achieved. These fluxes are adequate to test Zry cladding according to draft regulatory guides and to test SiC cladding according to past experiments.

Oxidation↗

DOE OSTI2023

H 2 generation by the 10 B(n,α) 7 Li reaction in high temperature water

H 2 produced in water from the 10 B(n,α) 7 Li fission reaction has been measured up to 300 °C. Thermal energy neutrons from the Rhode Island Nuclear Science Center's 2 MW reactor interact with boric acid-containing water in temperature-controlled high-pressure cells made from tubing of either titanium or zirconium alloy. After exposure for a minimum of 1 h, the solution sample is extracted and sparged with argon. The H 2 entrained by the sparging gas is sampled with a small mass spectrometer. A small amount of sodium is included in the boric acid solution so that after sparging, samples can be collected for 24 Na activation measurements in a gamma spectrometer to determine the neutron exposure and thus the total energy deposited in solution. The G-value (μmol/J) for H 2 production is obtained for water at a pressure of 25 MPa, over a temperature range from 20 °C to 300 °C. The weak temperature dependence of this yield between 150 °C and 200 °C demonstrates that the bimolecular reaction of pairs of e$^{–}_{aq}$ is a very minor source of H 2 in high LET tracks.

10B↗

DOE OSTI2023

Study of Tritium Diffusivity in Pure and Sn-Defective Zr: A First-Principles Density Functional Theory Approach

Zirconium alloys (e.g., zircaloy-4) are used as tritium ( 3 H) getter materials in tritium-producing burnable absorber rods (TPBARs) owing to their ability to capture 3 H and chemically convert them into metal hydrides. Understanding of 3 H diffusion mechanisms in zircaloy is crucial for the optimal design of material performance in nuclear technology. Here, for this work, we perform first-principles density functional theory calculations to study the 3 H diffusion mechanism in pure and impure Zr with a low concentration of tin (Sn) atoms to determine the impact of the presence of Sn on the movement of 3 H atoms through the material. First, we calculated the diffusion barriers for 3 H in pure Zr by taking different migration pathways. We then introduced a low concentration of Sn impurity and systematically explored the impurity effect on the diffusion barriers for 3 H. Using our calculated diffusion energy barriers, we further obtained the diffusion coefficients and analyzed the results by comparing them with the experimental and previously calculated values. A diffusion coefficient of the order of 10 –8 m 2 /s is predicted. We also found that the presence of a Sn impurity could reduce the diffusivity up to 4 orders of magnitude. In conclusion, our results could serve as guidelines for further experimental investigations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Tritium adsorption and absorption on (100) and (001) surfaces of pure and tin defective zirconium

Zirconium alloys such as zircaloy-4 are used as tritium (T) getter materials in tritium-producing burnable absorber rods (TPBARs) due to their ability to capture T, thereby forming metal hydrides. Developing an understanding of T adsorption onto zircaloy prior to diffusion into the subsurface is relevant for rational tritium getter and TPBAR design, to improve material properties for nuclear applications. Herein, density functional theory calculations revealed the preferred binding sites for T adsorption on Zr(001) and Zr(100). The energy barriers of T transfer, along the surface and from the surface to the subsurface were computed. The adsorption properties of Zr(001) were found to be superior to those of Zr(100). Surface tin impurities were found to strongly repel T. The presence of subsurface and surface tin resulted in higher absorption energy barriers for both the forward and reverse processes. Based on the calculated energy barriers, a surface to surface T diffusion coefficient of 9.53 × 10 -10 m 2 s -1 is expected for pristine Zr(001). Finally, a surface to subsurface T diffusion coefficient on the order of 10 -13 m 2 s -1 is predicted in pristine Zr, decreasing to 10 -19 m 2 s -1 for the transfer with a subsurface tin impurity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Physics-based model of irradiation creep for ferritic materials under fusion energy operation conditions

Irradiation creep is known to be an important process for structural materials in nuclear environments, potentially leading to creep failure at temperatures where thermal creep is generally negligible. While there is a great deal of data for irradiation creep in steels and zirconium alloys in light water reactor conditions, much less is known for first wall materials under fusion energy conditions. Lacking suitable fusion neutron sources for detailed experimentation, modeling, and simulation can help bridge the dose-rate and spectral-effects gap and produce quantifiable expectations for creep deformation of first wall materials under standard fusion conditions. In this paper, we develop a comprehensive model for irradiation creep created from merging a crystal plasticity representation of the dislocation microstructure and a defect evolution simulator that accounts for the entire cluster dimensionality space. Both approaches are linked by way of a climb velocity that captures dislocation-biased defect absorption and a dislocation strengthening term that reflects the accumulation of defect clusters in the system. Here, we carry out our study in Fe under first wall fusion reactor conditions, characterized by a fusion neutron spectrum with average recoil energies of 20 keV and a damage dose rate of ≈3×10 –7 dpa/s at temperatures between 300 and 800 K.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Viscoplastic selfconsistent (VPSC) code (version 8, open source)

VPSC is a mean-field polycrystal plasticity code for the prediction of the mechanical response and microstructure evolution of polycrystalline aggregates. The VPSC code is the computational realization of the visco-plastic self-consistent theory of polycrystal deformation. Both the theory and details of its numerical implementation were originally reported by R.A. Lebensohn and C.N. Tomé: "A self-consistent approach for the simulation of plastic deformation and texture development of polycrystals: application to Zirconium alloys", Acta Metallurgica et Materialia 41, 2611 (1993). Since then, the VPSC code has experienced several improvements and extensions and it is nowadays extensively used to simulate plastic deformation of polycrystalline aggregates and to interpret experimental evidence on metals, minerals and polymers.

Lebensohn, Ricardo↗

DOE OSTI2022

A review of cladding failure thresholds in RIA conditions based on transient reactor test data and the need for continued testing

Transient reactor experiments on light water reactor (LWR) fuel pins had been conducted since the beginning of the nuclear era to help determine core coolability and cladding failure thresholds. During one such test in November of 1993 at the CABRI transient test reactor on a test involving a high burnup fuel rod with a corroded Zircaloy-4 cladding it was first observed that cladding failures could occur prior to a departure from nucleate boiling (pre-DNB) at lower-than-expected peak radial average enthalpies. This paper will present an independent review of the publicly available transient reactor test database on higher burnup LWR pins conducted at the CABRI and NSRR reactors as well as review of a selection of published out of pile mechanical testing methods. The purpose of the review is to determine how well the new regulatory limits are supported by experimental data. The review will identify if additional transient reactor tests could provide additional support for the NRC guidance or identify the need for revisions. The evaluation will consider how far the existing database can be extrapolated when considering low hydrogen zirconium alloy claddings (with and without protective coatings) containing very high burnup (> 70 MWd/kgU) UO2 fuel pellets. Finally, the authors will suggest how out of pile mechanical tests can be used in conjunction with a limited number of transient reactor tests to develop cladding specific failure thresholds in RIA type transients.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Design and Evaluation of a Ring Tension Test Grip for Remote Mechanical Testing of Irradiated Tubular Specimens

Here, the ring tension test (RTT) is a mechanical testing method for determining bulk mechanical behavior in the circumferential or hoop direction for tubular materials. The test is especially useful for testing materials with anisotropic mechanical properties, such as zirconium alloys, which are commonly used as nuclear fuel cladding. Anisotropy requires direction-specific testing to determine the hoop strength. Historically, several RTT methods and grips have been used, each method has its strengths and weaknesses, and, in all cases, the measured strength is subject to uncertainty due to variations of the testing geometry and experimental tolerances. Recent analysis has shown that grips with a hemicylindrical mandrel configuration are recommended as the most robust configuration. The two strictest aspects to be controlled are the ability to determine gage region orientation and closely matching the size of the mandrels to the test specimen. This last requirement is particularly challenging when the dimensions of the specimen vary because of environmental effects such as dimensional changes due to irradiation. This paper presents a new RTT grip designed to incorporate this mandrel shape, hold the gage at the desired orientation, be suitable for remote operation in a hot-cell environment, and be adaptable for different sizes or variations in the specimen size. The general description and the unique design features of the test specimen and grips are given in detail. The performance of the grips in mechanical testing, including in a remote hot-cell environment, is also provided.

42 ENGINEERING↗

DOE OSTI2020

SCALE Lattice Physics Code Assessments of Accident Tolerant Fuel

This report highlights accident-tolerant fuel (ATF) code assessment activities performed under Project NRCHQ- 60-17-T-0017, Lattice Physics Enhancements and Assessment. ATF covers a broad range of advanced fuel and clad designs for light water reactors (LWRs) to enhance performance under several accident conditions. Several ATF concepts are anticipated to be deployed as lead test rods (LTRs) or lead test assemblies (LTAs) within the next five years. The purpose of this work is to assess the predictive capabilities of NRC neutronics codes that underpin various licensing calculations. ATF designs use different fuel and clad materials compared to standard UO 2 fuel and zirconium-alloy claddings (hereafter UO 2 -Zry). These new materials and geometrical designs need to be assessed to quantify the impact of nuclear data uncertainties on quantities of interest (QOIs) in licensing calculations and the impact of modeling approximations which may be valid for UO 2 -Zry but not for ATF. This report outlines a systematic approach for ATF neutronics code assessment which includes sensitivity and uncertainty (S/U) analysis of nuclear data, identification of experimental benchmark and gaps for code validation, investigation of modeling approximations, and code-to-code comparisons of calculated QOIs against high-fidelity reference continuous energy (CE) Monte Carlo (MC) calculations. This report focuses on the assessment of the SCALE/Polaris lattice physics code for reactor safety analysis. Polaris lattice physics calculations generate few group (FG) cross sections for PARCS full-core calculations. (Full-core analysis, spent fuel analysis, and severe accident analysis will be performed in future work.) The selected ATF concepts for this report include Cr 2 O 3 and Al 2 O 3 -Cr 2 O 3 -doped UO 2 fuel, U 3 Si 2 fuel, FeCrAl cladding, SiC cladding, and Cr-coated cladding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Evaluation of Hydrogen Generation in High Burnup Demonstration Dry Storage Cask

This report provides a best-estimate evaluation of residual water content (post-dry out) in the High Burnup (HBU) LWR Spent Fuel Demonstration project TN-32 cask, and evaluates the radiolysis of the residual free water, and the physisorbed and chemisorbed waters on the surfaces of the fuel and cask internal contents. The evaluation of radiolytic breakdown of those waters with gamma radiation causing the generation of hydrogen gas (H 2 ) is made using available literature data and models. This evaluation is part of the overall materials performance evaluation of the SNF-in-canister system, and is part of the technical bases for their continued safe dry storage. The TN-32 cask contents included 32 HBU LWR spent fuel assemblies each with 264 fuel rods clad in zirconium alloys, aluminum neutron absorber components, and aluminum and stainless steel structural components. The residual free and surface (physisorbed/chemisorbed) waters are ascribed to water vapor in the free volume and to components’ surfaces, respectively. The total potential radiolytic hydrogen inventory from the water vapor and from waters ascribed to surfaces has been calculated assuming all the water produced molecular H 2 . The residual water that is chemically incorporated into the bulk of a hydrated oxide, i.e., chemisorbed water, and its total potential hydrogen inventory has been calculated. These calculations are at the physical limit of material available and are used for a bounding assessment purpose only.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

AFC FY 2023 HFIR Irradiation Test Matrix – Supported by the Design of a Ring Specimen Irradiation Vehicle

The development and deployment of accident-tolerant cladding materials in light water nuclear reactors requires the collection of neutron-irradiated properties of these materials with specific consideration to the material properties orientation (i.e., tube geometry). To that end, a test plan to irradiate several cladding tube and ring specimens in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) was proposed, along with the development of a new capsule design that features ring specimens with a preexisting gauge section. This ring specimen geometry removes the need to machine a gauge section on the irradiated specimen and thus allows for direct application of a ring-pull test post-irradiation. The test matrix includes uncoated and chromium-coated Zircaloy-4 and advanced zirconium alloy cladding specimens, pre-characterized at ORNL. Plans are to irradiate the specimens at about 4 and 10 dpa—corresponding to two and five cycles at the HFIR centerline—with a target specimen gauge section temperature of 330°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Irradiation creep model for α-Fe: Dislocation climb in the presence of stress fields (Final Report)

Irradiation creep is known to be an important process for structural materials in nuclear environments, potentially leading to creep failure at temperatures where thermal creep is generally negligible. While there is a great deal of data for irradiation creep in steels and zirconium alloys in light water reactor conditions, much less is known for first wall materials under fusion energy conditions. Lacking suitable fusion neutron sources for detailed experimentation, modeling, and simulation can help bridge the dose-rate and spectral-effects gap and produce quantifiable expectations for creep deformation of first wall materials under standard fusion conditions. In this work, we present a comprehensive model for irradiation creep created from merging a crystal plasticity representation of the dislocation microstructure and a defect evolution simulator that accounts for the entire cluster dimensionality space. Both approaches are linked by way of a climb velocity that captures dislocation-biased defect absorption and a dislocation strengthening term that reflects the accumulation of defect clusters in the system. We carry out our study in Fe under first wall fusion reactor conditions, characterized by a fusion neutron spectrum at temperatures between 300 and 800°K.

36 MATERIALS SCIENCE↗

DOE OSTI2025

ATF Cladding Mechanical Properties Report: Capability Demonstration

This report documents post-irradiation examination (PIE) activities performed in FY 2025 at Oak Ridge National Laboratory on chromium-coated (Cr-coated) and uncoated advanced zirconium alloy claddings irradiated in the High Flux Isotope Reactor (HFIR) to approximately 4 displacements per atom (dpa), corresponding to ~40 GWd/t burnup. Specimens were prepared in axial tension (ATT) and ring tension (RTT) geometries, and passive silicon carbide thermometry was employed to determine irradiation temperatures, which averaged 38–43 °C below the 330 °C design target.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

PIE-Enabled Study of Aqueous Corrosion & Zr Hydriding in Cr-Coated Cladding: M3GV-23PN0101132

Chromium-coated zirconium alloy cladding is under investigation as an accident-tolerant fuel (ATF) concept to extend performance to higher burnups via improved oxidation resistance and reduced hydrogen pickup. However, hydrothermal corrosion behavior and hydrogen transport mechanisms governing in-service hydriding of these coatings remain poorly understood. In a collaborative study between Pacific Northwest National Laboratory (PNNL), Idaho National Laboratory (INL), and the University of Huddersfield, cold spray (CS) and physical vapor deposition (PVD) Cr-coated Optimized ZIRLO™ cladding samples were characterized after exposure to PWR-simulated water chemistry under both in-core (neutron irradiation) and out-of-core (aqueous-only) conditions at the MIT Research Reactor. Multi-scale characterization was performed independently at PNNL and INL to evaluate coating integrity, microstructural evolution, Cr/Zr interface chemistry, and hydride formation. Both laboratories observed a consistent divergence in hydriding behavior: out-of-core CS Cr-coated cladding exhibited elevated hydride concentrations exceeding those of uncoated cladding, whereas in-core CS samples showed substantially suppressed hydriding. In-core specimens also displayed irradiation-specific features, including nanoscale voids within the Cr coating and radiation-induced segregation clusters in the Zr substrate. CS coatings retained an interdiffusion-free Cr/Zr bond with no intermetallic layer, whereas PVD coatings exhibited inferior quality with visible cracks and pores. An automated image-based hydride quantification method systematically overestimated bulk hydrogen content relative to inert gas fusion measurements, underscoring the need for standardized sample preparation and reference standards. Interpretation of hydride nucleation and growth is complicated by the open inner-diameter of the specimens, which provides additional hydrogen pathways. The results motivate further foundational studies to support predictive models of hydrothermal corrosion and hydrogen transport in unirradiated and irradiated Cr-coated cladding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Material Characterization Report of EBR II Mark IV Fuel Element

The focus of this report is the characterization of an unirradiated as-built fuel element from the Experimental Breeder Reactor II (EBR-II) Mark IV driver fuel design. The fuel in this element is a metallic uranium-zirconium alloy, and the cladding material is HT9 stainless steel. Both the metallic fuel and cladding materials are characterized, including chemical composition, grain size, morphology, phase composition, precipitate composition, crystallography, density, and hardness.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Cold spray chromium coating for nuclear fuel rods

A method is provided for coating the substrate of a component, such as a zirconium alloy cladding tube, for use in a water cooled nuclear reactor under normal operating conditions and under high temperature oxidation conditions. The method includes heating a pressurized carrier gas to a temperature between 200° C. and 1200° C., adding chromium or chromium-based alloy particles having an average diameter of 20 microns or less to the heated carrier gas, and spraying the carrier gas and particles onto the substrate at a velocity, preferably from 800 to 4000 ft./sec. (about 243.84 to 1219.20 meters/sec.), to form a chromium and/or chromium-based alloy coating on the substrate to a desired thickness.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Neutronic Consideration of TREAT Facility Fuel SiC Recladding

The Transient Reactor Test (TREAT) Facility is an air-cooled reactor composed of graphite-urania fuel encapsulated in zirconium alloy canisters and surrounded by ~2 ft (~61 cm) of nuclear grade graphite. The primary role of TREAT is to provide in-pile nuclear-heated safety research via transient testing [1]. Benchmark efforts have demonstrated sensitivity of TREAT neutronics models to graphite cross section data and key neutron poisons found in the fuel assemblies [2]. During fabrication of TREAT fuel assemblies, a small concentration of boron was inadvertently introduced with variable concentration into the aggregate of fuel blocks prepared for TREAT use. The concentration of boron, and its respective uncertainty, represent the most sensitive component in a neutronics study; unfortunately, nothing can be done to reduce or otherwise mitigate its impact. Hydrogen in the fuel blocks reduces the mean free path of the core and its true quantity and uncertainty is approximated. The hydrogen remains from pitch binder used in the fuel fabrication process and was not completely released due to incomplete fuel graphitization. Destructive fuel testing is necessary to quantify the actual hydrogen content and to improve benchmark model quality. A third neutron poison of some significance is the hafnium impurity in the Zircaloy-3 (Zry-3) assembly cladding. The quantity of hafnium is expected to be within nominal manufacturing limits for nuclear grade zircaloy. Recladding the fuel assemblies with material that is less neutron absorbing is expected to benefit reactor neutron economy. Moreover, TREAT’s total transient energy is restricted based on the rate of Zry-3 oxidation in TREAT’s air coolant environment. Hence, cladding with more benign air reaction kinetics could dramatically uprate the facility’s experimental capability. Silicon carbide (SiC) has been proposed as a candidate material for recladding TREAT assemblies, as SiC/SiC demonstrate favorable properties within nuclear environments [3]. The current operational limits of TREAT are restricted by the oxidation of Zry-3. Change of the cladding to SiC could feasibly double the current temperature limitation. Recladding opportunities allow for previously damaged fuel assemblies to be returned to service, as Zry-3 is not commercially available. The initial effort required to consider proceeding with any recladding effort is to neutronically characterize key reactor parameters while replacing Zry-3 with SiC. A characterization summary, with respective results, is provided herein.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Establishing Maximal Core Excess Reactivity Envelope for TREAT Test Vehicle Insertion

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗