Search NASA⌕ Search

SEARCH · Search NASA

Results for “aeroacoustics testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Determination of HART I Blade Structural Properties by Laboratory Testing

The structural properties of higher harmonic Aeroacoustic Rotor Test (HART I) blades were measured using the original set of blades tested in the German-dutch wind tunnel (DNW) in 1994. the measurements include bending and torsion stiffness, geometric offsets, and mass and inertia properties of the blade. the measured properties were compared to the estimated values obtained initially from the blade manufacturer. The previously estimated blade properties showed consistently higher stiffness, up to 30 percent for the flap bending in the blade inboard root section.

Jung, Sung N.↗
NASA NTRS2014

Acoustic Measurements from Wind Tunnel Test of AMELIA - Advanced Model for Extreme Lift and Improved Aeroacoustics

A wind tunnel test has been conducted to measure the aerodynamic and acoustic performance of an active circulation-control aircraft with leading- and trailing- edge slot blowing. The 11 Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA) model was tested in the Arnold Engineering Development Center (AEDC) National Full Scale Aerodynamics Complex (NFAC) 40- by 80-Ft wind tunnel. Forward velocities ranged from 0 to Mach 0.15 and total slot mass-flow was varied from 0 to 2.8 lbmsec. Angle-of-attack and sideslip ranges were -5 to 25 and -10 to 10, respectively.This reports summarizes acoustic measurements from the wind tunnel test and the corrections applied to the released acoustic data. The analysis focuses on measurements for the clean wing configuration (turbine propulsion simulators removed) with trailing-and leading-edge slot blowing and with trailing-edge blowing, for systematic variations in slot mass flow from nearly zero to the system maximum. The acoustic measurements from a fixed phased microphone array and seven fixed microphones were corrected for sensor directional response and atmospheric attenuation. Graphs of 13-octave spectra, narrowband spectra, and directional variations in OASPL are presented for each active lift configuration. This report is intended to document the corresponding set of corrected data that is now available for development and verification of new predictive models of the active lift source.For large slot mass flow conditions 13-octave spectral shapes were level and flat, typical of a pink noise source. Little source directivity was present in the OASPL levels for the 0 flap conditions and show only a slight downstream increase with the 60 flap configuration. For moderate to high slot mass flow conditions trailing-edge only blowing spectra were similar to leading- and trailing edge blowing cases. However for the lower mass flows variations of as much as 5 dB were observed.

CCW↗
NASA NTRS1980

Aeroacoustic wind-tunnel tests of a light twin-boom general-aviation airplane with free or shrouded-pusher propellers

Tests were conducted in the Langley full-scale tunnel to determine the aerodynamic performance and acoustic characteristics of four different pusher-propeller configurations on a twin boom, general aviation airplane. The propellers included a 2-blade free propeller, two 3-blade shrouded propellers, and a 5-blade shrouded propeller. The tests were conducted for a range of airplane angles of attack from about 0 deg to 16 deg for test speeds from 0 to about 36 m/sec and for a range of propeller blade angles and rotation speeds. The free propeller provided the best aerodynamic propulsive performance. For forward flight conditions, the free propeller noise levels were lower than those of the shrouded propellers. In the static conditions the free propeller noise levels were as low as those for the shrouded propellers, except for the propeller in-plane noise where the shrouded propeller noise levels were lower.

Mclemore, H. C.↗
NASA NTRS2015

Fuselage-Induced Velocity Model for LRTA, RTA, and HART Fuselages

In order to make the aerodynamic fuselage-rotor interference effects available to comprehensive rotor codes, a simple analytical model of the fuselage-induced velocities within the volume of rotor blade operation above the fuselage is developed here for the following bodies used in wind tunnel experiments: the Large Rotor Test Apparatus (LRTA), the Rotor Test Apparatus (RTA), and the Higher Harmonic Control Aeroacoustic Rotor Test (HART).While the first two are used in the National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames, California, the third one is used by DLR in the large low-speed facility of the German-Dutch wind tunnel in the Netherlands. The fuselage-induced velocity model is based on parameter identification of isolated fuselage-induced velocity data (computed by means of computational fluid dynamics, CFD) and is intended to be generic enough to be used for real helicopter fuselages as well. The accuracies obtained in reproducing the CFD data show a remaining average error of less or equal 5 of the peak-to-peak induced velocity range, which is considered sufficient for comprehensive code analysis.

HART↗
NASA NTRSDate not supplied

Toward Relating Open- and Closed-Test Section Microphone Phased Array Aeroacoustic Measurements

Aeroacoustic measurements utilizing microphone phased arrays are becoming more commonplace in large-scale wind tunnels. However, for such costly tests it is difficult to assess the influence of a given facility's configuration on the acquired data. One such opportunity has recently arisen in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel, where the High-Lift configuration of the Common Research Model was tested in both open-jet and closed wall configurations. Acoustic data were acquired on the same model with the same specific hardware at the same Mach number; and for similar model angles of attack, array apertures, and array angles relative to the model location. Initial deconvolution comparisons using DAMAS appear poor. The closed test section results show contamination likely due to background noise and reflections. The open-jet results show severe blurring due to the decorrelation of acoustic waves passing through a turbulent free shear layer. However, accounting for image sources in the DAMAS grid reduces visual artifacts in the closed test section results, and a preliminary coherence correction technique mitigates the blurring in the open-jet results. Qualitatively, both tests identify similar source behavior. Quantitatively, summed spectra of the slat noise agree in some frequency bands but differ in others. Proposals that may mitigate the difference are given for each configuration, such as correcting for the array protective cover and applying background subtraction in the closed wall configuration, and further developing the coherence loss correction for deconvolution methods in the open-jet setup.

microphone array↗
NASA NTRS1997

Least-Squares Spectral Element Solutions to the CAA Workshop Benchmark Problems

This paper presents computed results for some of the CAA benchmark problems via the acoustic solver developed at Rocketdyne CFD Technology Center under the corporate agreement between Boeing North American, Inc. and NASA for the Aerospace Industry Technology Program. The calculations are considered as benchmark testing of the functionality, accuracy, and performance of the solver. Results of these computations demonstrate that the solver is capable of solving the propagation of aeroacoustic signals. Testing of sound generation and on more realistic problems is now pursued for the industrial applications of this solver. Numerical calculations were performed for the second problem of Category 1 of the current workshop problems for an acoustic pulse scattered from a rigid circular cylinder, and for two of the first CAA workshop problems, i. e., the first problem of Category 1 for the propagation of a linear wave and the first problem of Category 4 for an acoustic pulse reflected from a rigid wall in a uniform flow of Mach 0.5. The aim for including the last two problems in this workshop is to test the effectiveness of some boundary conditions set up in the solver. Numerical results of the last two benchmark problems have been compared with their corresponding exact solutions and the comparisons are excellent. This demonstrates the high fidelity of the solver in handling wave propagation problems. This feature lends the method quite attractive in developing a computational acoustic solver for calculating the aero/hydrodynamic noise in a violent flow environment.

Lin, Wen H.↗
NASA NTRS2002

Design and Development of a Deep Acoustic Lining for the 40-by 80-Foot Wind Tunnel Test Section

The work described in this report has made effective use of design teams to build a state-of-the-art anechoic wind-tunnel facility. Many potential design solutions were evaluated using engineering analysis, and computational tools. Design alternatives were then evaluated using specially developed testing techniques, Large-scale coupon testing was then performed to develop confidence that the preferred design would meet the acoustic, aerodynamic, and structural objectives of the project. Finally, designs were frozen and the final product was installed in the wind tunnel. The result of this technically ambitious project has been the creation of a unique acoustic wind tunnel. Its large test section (39 ft x 79 ft x SO ft), potentially near-anechoic environment, and medium subsonic speed capability (M = 0.45) will support a full range of aeroacoustic testing-from rotorcraft and other vertical takeoff and landing aircraft to the take-off/landing configurations of both subsonic and supersonic transports.

Soderman, Paul T.↗
NASA NTRSDate not supplied

A Field-Deployable Wireless Data Acquisition System for Ground-Test Arrays

This paper describes the development, characterization, and deployment of a field-deployable wireless data acquisition system for ground-test arrays, applicable in noise-source localization or beamforming measurements such as those encountered during airframe noise flyover measurement tests. The system design is enabled by commercially available, low-power Internet of Things (IoT) processors and Wi-Fi communication components. Time is synchronized across the array wirelessly by leveraging the Coordinated Universal Time (UTC) time provided by the Global Positioning System (GPS). Initial laboratory characterization of the system demonstrated its ability to meet acoustic bandwidth, dynamic range, time synchronization, environmental, and battery life requirements for typical ground-test array deployments. A successful system deployment at NASA Langley was performed that included measurement of a suspended elevated static noise source, and Uncrewed Aerial System (UAS) vehicle measurements using a quadcopter operated both in hover mode and forward flight. Beamform analysis of the acquired data showed an excellent ability of the array to extract accurate sound pressure levels from the suspended source. Synchronization of the array and vehicle GPS timecodes allowed the ability to extract acoustic signatures from the UAS vehicle during hover and forward flight maneuvers over the array. These results validate that the use of a high channel count wireless array is advantageous in airframe and propulsion noise flyover test campaigns.

wireless↗
NASA NTRS2003

Airloads and Wake Geometry Calculations for an Isolated Tiltrotor Model in a Wind Tunnel

Th tiltrotor aircraft configuration has the potential to revolutionize air transportation by providing an economical combination of vertical take-off and landing capability with efficient, high-speed cruise flight. To achieve this potential it is necessary to have validated analytical tools that will support future tiltrotor aircraft development. These analytical tools must calculate tiltrotor aeromechanical behavior, including performance, structural loads, vibration, and aeroelastic stability, with an accuracy established by correlation with measured tiltrotor data. For many years such correlation has been performed for helicopter rotors (rotors designed for edgewise flight), but correlation activities for tiltrotors have been limited, in part by the absence of appropriate measured data. The recent test of the Tilt Rotor Aeroacoustic Model (TRAM) with a single, U4-scale V-22 rotor in the German-Dutch Wind Tunnel (DNW) now provides an extensive set of aeroacoustic, performance, and structural loads data. This paper will present calculations of airloads, wake geometry, and performance, including correlation with TRAM DNW measurements. The calculations were obtained using CAMRAD II, which is a modern rotorcraft comprehensive analysis, with advanced models intended for application to tiltrotor aircraft as well as helicopters. Comprehensive analyses have received extensive correlation with performance and loads measurements on helicopter rotors. The proposed paper is part of an initial effort to perform an equally extensive correlation with tiltrotor data. The correlation will establish the level of predictive capability achievable with current technology; identify the limitations of the current aerodynamic, wake, and structural models of tiltrotors; and lead to recommendations for research to extend tiltrotor aeromechanics analysis capability. The purpose of the Tilt Rotor Aeroacoustic Model (TRAM) experimental project is to provide data necessary to validate tiltrotor performance and aeroacoustic prediction methodologies and to investigate and demonstrate advanced civil tiltrotor technologies. The TRAM project is a key part of the NASA Short Haul Civil Tiltrotor (SHCT) project. The SHCT project is an element of the Aviation Systems Capacity Initiative within NASA. In April-May 1998 the TRAM was tested in the isolated rotor configuration at the Large Low-speed Facility of the German-Dutch Wind Tunnels (DNW). A preparatory test was conducted in December 1997. These tests were the first comprehensive aeroacoustic test for a tiltrotor, including not only noise and performance data, but airload and wake measurements as well. The TRAM can also be tested in a fill-span configuration, incorporating both rotors Lnd a fuselage model. The wind tunnel installation of the TRAM isolated rotor is shown. The rotor tested in the DNW was a 1/4-scale (9.5 ft diameter) model of the right-hand V-22 proprotor. The rotor and nacelle assembly was attached to an acoustically-treated, isolated rotor test stand through a mechanical pivot (the nacelle conversion axis). The TRAM was analyzed using the rotorcraft comprehensive analysis CAMRAD II. CAMRAD II is an aeromechanical analysis of helicopters and rotorcraft that incorporates a combination of advanced technologies, including multibody dynamics, nonlinear finite elements, and rotorcraft aerodynamics. The trim task finds the equilibrium solution (constant or periodic) for a steady state operating condition, in this case a rotor operating in a wind tunnel. For wind tunnel operation, the thrust and flapping are trimmed to target values. The aerodynamic model includes a wake analysis to calculate the rotor nonuniform induced-velocities, using a free wake geometry. The paper will present the results of CAMRAD II calculations compared to the TRAM DNW measurements for hover performance, helicopter mode performance, and helicopter mode airloads. An example of the hover performance results, comparing both mearements and calculations for the JVX (large scale) and TRAM (small scale) rotors, is shown. An example of the helicopter mode performance, showing the influence of the aerodynamic model (particularly the stall delay model) on the calculated power, induced power, and profile power is also shown. An example of the helicopter mode airloads, showing the influence of various wake and aerodynamic models on the calculations, is shown. Good correlation with measured airloads is obtained using the multiple-trailer wake model. The paper will present additional results, and describe and discuss the aerodynamic behavior in detail.

Johnson, Wayne↗
NASA NTRS2012

Acoustic Surveys of a Scaled-Model CESTOL Transport Aircraft in Static and Forward Speed Conditions

An 11% scale-model of a Cruise-Efficient Short Take-off and Landing (CESTOL) scalemodel test was recently completed. The test was conducted in the AEDC National Full-Scale Aerodynamic Complex (NFAC) 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. The model included two over-wing pod-mounted turbine propulsion simulators (TPS). The hybrid blended wing-body used a circulation control wing (CCW) with leadingand trailing-edge blowing. The bulk of the test matrix included three forward velocities (40 kts, 60 kts, and 100kts), angle-of-attack variation between -5 and 25 , and CCW mass flow variation. Seven strut-mounted microphones outboard of the left wing provided source directivity. A phased microphone array was mounted outboard of the right wing for source location. The goal of this paper is to provide a preliminary look at the acoustic data acquired during the Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA) test for 0 angle-of-attack and 0 sideslip conditions. Data presented provides a good overview of the test conditions and the signal-to-noise quality of the data. TPS height variation showed a difference of 2 dB to 3 dB due to wing shielding. Variation of slot mass flow showed increases of 12 dB to 26 dB above the airframe noise and the TPS increased the overall levels an additional 5 dB to 10 dB.

Burnside, Nathan↗
NASA NTRS2021

Plug20 Test Report

This report documents a test of aircraft exhaust nozzle designs applicable to commercial supersonic aircraft as envisioned in the 2025-2035 time frame. The test is primarily intended to provide data about the noise such aircraft would produce during landing and takeoff (LTO) operation, specifically the jet noise component of this noise. The tests were conducted at the NASA Glenn Research Center’s Aero-Acoustic Propulsion Laboratory in March 2020. The tests used the High-Flow Jet Exhaust Rig in the Nozzle Acoustic Test Rig which simulates the flow from a dual-stream turbofan engine in a flight stream. Seven exhaust configurations were tested with various combinations of internal mixer and external plug, and covered engine cycles having nozzle pressures from 1.5 to 2.3 at a flight speed of Mach 0.3. A few unheated flow conditions were also tested to tie results to other baseline test results. Data acquired and included in this report are 1) far-field acoustic spectra, 2) phased array measurements of noise source distributions, and 3) background-oriented schlieren of the flow near the nozzles. These data, along with the nozzle geometry in CAD format, are given as Appendices and are available online.

Jet noise↗
NASA NTRS1995

Laser doppler velocimeter system for subsonic jet mixer nozzle testing at the NASA Lewis Aeroacoustic Propulsion Lab

A laser Doppler velocimeter (LDV) system developed for the Aeroacoustic Propulsion Laboratory (APL) at the NASA Lewis Research Center is described. This system was developed to acquire detailed flow field data which could be used to quantify the effectiveness of internal exhaust gas mixers (IEGM's) and to verify and calibrate computational codes. The LDV was used as an orthogonal, three component system to measure the flow field downstream of the exit of a series of IEGM's and a reference axisymmetric splitter configuration. The LDV system was also used as a one component system to measure the internal axial flow within the nozzle tailpipe downstream of the mixers. These IEGM's were designed for low-bypass ratio turbofan engines. The data were obtained at a simulated low flight speed, high-power operating condition. The optical, seeding, and data acquisition systems of the LDV are described in detail. Sample flow field measurements are provided to illustrate the capabilities of the system at the time of this test, which represented the first use of LDV at the APL. A discussion of planned improvements to the LDV is also included.

Podboy, Gary G.↗
NASA NTRSDate not supplied

Refined Predictions Compared with the Propulsion Airframe Aeroacoustics and Aircraft System Noise Flight Research Test Data

In a collaboration between NASA and The Boeing Company, the Propulsion Airframe Aeroacoustics and Aircraft System Noise Flight Research Test was executed by the Boeing ecoDemonstrator Program in 2020 with an Etihad Airways Boeing 787-10 aircraft. This ambitious flight research successfully accomplished many objectives and constitutes the most comprehensive and highest quality acoustic flight data available to NASA for a modern commercial subsonic transport aircraft. One purpose of these data is to be the measure of accuracy for the aircraft system noise prediction capabilities of NASA. This research reviews the impact of the major improvements in prediction methods implemented up to this point and tested in the Research version of the NASA Aircraft Noise Prediction Program. The improvements have been to the prediction of jet source and jet-flap interaction, to both fan broadband and tone source prediction, and to the prediction of propulsion airframe aeroacoustic scattering effects. In general, over the engine power range, comparisons between prediction and flight data are within 2 EPNdB including for the intentional sideline-to-sideline asymmetries as implemented in the flight test by flying the aircraft with only one engine at power. Considerable progress has been shown here in the continuing effort to advance the fidelity of NASA aircraft noise prediction capabilities for subsonic aircraft flight acoustics, modern transport aircraft and future aircraft concepts.

aircraft system noise prediction↗