Search NASA⌕ Search

SEARCH · Search NASA

Results for “coefficient semiconductor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Epitaxial growth of rock salt MgZrN 2 semiconductors on MgO and GaN

Ternary nitride compound semiconductors have attracted recent attention as electronic materials since their properties can be tuned by cation stoichiometry and ordering. A recently discovered example is MgZrN 2 , a ternary analog to the rock salt semiconductor ScN. MgZrN 2 has a larger bandgap and stronger dielectric response than the binary compound. Polycrystalline thin films of MgZrN 2 have been studied, but demonstration of high-quality growth is still required to establish its suitability for technological applications. Here, we report on epitaxial growth of MgZrN 2 thin films on (100) and (111) MgO substrates and (001) GaN templates. The MgZrN 2 composition is confirmed by Rutherford backscattering spectrometry, showing no oxygen in the film except for a thin surface oxide layer. Epitaxial growth results in MgZrN 2 with x-ray diffraction rocking curves with a full-width at half-maximum in the range of 0.3–3.0°, depending on the substrate. Transmission electron microscopy analysis of the MgZrN 2 film grown on a (111) MgO substrate confirms epitaxial growth and shows a sharp film/substrate interface. In-plane temperature-dependent Hall effect measurements show that the material is an n-type semiconductor with a relatively high concentration ( n 300K ≈ 10 19 –10 20 cm -3 ) of thermally activated electrons. Room-temperature transport measurements show a conductivity of 25 S cm -1 and a Seebeck coefficient of -80 μ V K -1 . Overall, these results provide an important step toward integration of rock salt MgZrN 2 with other technological nitrides for device applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

New Zintl Phase Yb 10 MgSb 9 with High Thermoelectric Performance

Abstract Yb 10 MgSb 9 is a new Zintl compound (with a composition closer to Yb 10.5 MgSb 9 ) and a promising thermoelectric material first reported in this work. Undoped Yb 10 MgSb 9 has an ultralow thermal conductivity due to crystallographic complexity and exhibits a relatively high peak p‐type Seebeck coefficient and high electrical resistivity. This is consistent with Zintl counting and density functional theory (DFT) calculations that the composition Yb 10.5 MgSb 9 should be a semiconductor. Na is found experimentally to be an effective p‐type dopant potentially due to the replacement of Na + for Yb 2+ , allowing for a significant decrease in electrical resistivity. With doping, a dramatic improvement of electrical conductivity is observed and the glass‐like thermal conductivity remains low, allowing for a significant enhancement of the thermoelectric figure of merit, zT . Doping increases the zT from 0.23 in undoped Yb 10 MgSb 9 to 1.06 in 7 at% Na‐doped Yb 10 MgSb 9 at 873K. This high thermoelectric performance found through Na‐doping places this material amongst the leading p‐type Zintl thermoelectrics, making it a promising candidate for future studies and high‐temperature thermoelectric applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhancing the cooling performance of thermocouples: a power-constrained topology optimization procedure

Abstract Heat pumping through thermoelectric devices has many advantages over traditional cooling. However, their current efficiency is a limiting factor in their implementation. In this paper, we approach the non-convex topology optimization of thermoelectrical elements for cooling applications through the method of moving asymptotes (MMA) to improve their cooling capabilities per watt usage. The optimization problem is defined for a given power budget, aiming for the minimum temperature with a known heat pumping need. The introduction of power as a constraint justifies the introduction of the voltage gradient across the thermocouple as a design variable to maintain the thermoelectrical device in its optimum power-to-heat extraction ratio. To better understand the convergence of this non-convex problem, we present a two-variable analytical thermoelectric optimization model. This example provides information on how to select the penalty parameters used to scale the three material coefficients involved in the problem to obtain lower objective values and better convergence using MMA. The analytical model shows the non-convexity of the problem and provides the recommendation to use penalization coefficients of the form $$p_k=p_{\sigma }>p_{\alpha }=1$$ p k = p σ > p α = 1 for the thermal conductivity, electrical conductivity, and Seebeck coefficients. We tested these penalization coefficients through optimizations of a model based on the 1MC10-031 commercial thermoelectric-cooler (TEC) using the finite element method (FEM). These penalization coefficients provided local minima without the need for volume constraints. With this procedure, we found designs that provided temperatures close to 10 degrees lower using 60% less semiconductor material volume compared to the initial design.

Gutiérrez, G. Reales↗
DOE OSTI2023

Temperature dependence of resistivity of carbon micro/nanostructures: Microscale spatial distribution with mixed metallic and semiconductive behaviors

The temperature coefficient of resistivity (θ T ) of carbon-based materials is a critical property that directly determines their electrical response upon thermal impulses. It could have metal- (positive) or semiconductor-like (negative) behavior, depending on the combined temperature dependence of electron density and electron scattering. Its distribution in space is very difficult to measure and is rarely studied. Here, for the first time, we report that carbon-based micro/nanoscale structures have a strong non-uniform spatial distribution of θ T . This distribution is probed by measuring the transient electro-thermal response of the material under extremely localized step laser heating and scanning, which magnifies the local θ T effect in the measured transient voltage evolution. For carbon microfibers (CMFs), after electrical current annealing, θ T varies from negative to positive from the sample end to the center with a magnitude change of >130% over <1 mm. This θ T sign change is confirmed by directly testing smaller segments from different regions of an annealed CMF. For micro-thick carbon nanotube bundles, θ T is found to have a relative change of >125% within a length of ~2 mm, uncovering strong metallic to semiconductive behavior change in space. In conclusion, our θ T scanning technique can be readily extended to nm-thick samples with μm scanning resolution to explore the distribution of θ T and provide a deep insight into the local electron conduction.

36 MATERIALS SCIENCE↗
DOE OSTI2026

First-principles theory of direct-gap optical emission in hexagonal Ge and its enhancement via strain engineering

The emergence of hexagonal Ge (2H-Ge) as a candidate direct-gap group-IV semiconductor for Si photonics mandates a rigorous understanding of its optoelectronic properties. Theoretical predictions of a “pseudodirect” band gap, characterized by weak oscillator strength, contrast with a claimed high radiative recombination coefficient 𝐵 comparable to conventional (cubic) InAs. We compute 𝐵 in 2H-Ge from first principles and quantify its dependence on temperature, carrier density, and strain. For unstrained 2H-Ge, our calculated spontaneous emission spectra corroborate that measured photoluminescence corresponds to direct-gap emission, but with 𝐵 being approximately three orders of magnitude lower than in InAs. We confirm a pseudodirect-to-direct-gap transition under ∼2% [0001] uniaxial tension, which can enhance 𝐵 by up to 3 orders of magnitude, making it comparable to that of InAs. Beyond quantifying the strong enhancement of 𝐵 via strain engineering, our analysis suggests the dominance of additional, as-yet unquantified recombination mechanisms in this nascent material.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Comprehensive model for evaluating voltage losses and performance improvements in thin-film photovoltaic devices

Progress of state-of-the-art and next-generation thin-film photovoltaic devices is often stymied by open-circuit voltage (𝑉 oc ) that is significantly lower than theoretical and practical limits. Yet, effectively diagnosing the primary sources of voltage loss remains challenging. Herein, a sequence of device-level characterization techniques and simulations are employed to identify and rank loss mechanisms. For the research-based Cd⁡(Se,Te) device under study, most of the loss was at the front semiconductor heterointerface due to a clifflike conduction-band offset that lowered the recombination activation energy. Additional losses due to band tails were quantified by photoluminescence analysis. The latter provided the absorption coefficient and activation energy reduction associated with band tails as inputs to device models. Simulations showed that alleviating front-interface issues would improve 𝑉 oc , but it would then be limited by bulk recombination. Further improvement of the bulk would then lead to back-contact limitations. Reducing band tails is beneficial in any circumstance. In conclusion, this analysis provides guidance for reaching toward the radiative 𝑉 oc limit.

14 SOLAR ENERGY↗
DOE OSTI2021

Efficient calculation of carrier scattering rates from first principles

Abstract The electronic transport behaviour of materials determines their suitability for technological applications. We develop a computationally efficient method for calculating carrier scattering rates of solid-state semiconductors and insulators from first principles inputs. The present method extends existing polar and non-polar electron-phonon coupling, ionized impurity, and piezoelectric scattering mechanisms formulated for isotropic band structures to support highly anisotropic materials. We test the formalism by calculating the electronic transport properties of 23 semiconductors, including the large 48 atom CH 3 NH 3 PbI 3 hybrid perovskite, and comparing the results against experimental measurements and more detailed scattering simulations. The Spearman rank coefficient of mobility against experiment ( r s = 0.93) improves significantly on results obtained using a constant relaxation time approximation ( r s = 0.52). We find our approach offers similar accuracy to state-of-the art methods at approximately 1/500th the computational cost, thus enabling its use in high-throughput computational workflows for the accurate screening of carrier mobilities, lifetimes, and thermoelectric power.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Anomalous stability of non-van der Waals bonded B4C nanosheets through surface reconstruction

Boron carbide (B4C) has been well studied both theoretically and experimentally in its bulk form due to its exceptional hardness and use as a high-temperature thermoelectric. However, the properties of its two-dimensional nanosheets are not well established. In this paper, using van der Waals-corrected density-functional theory simulations, we show that bulk B4C can be cleaved along different directions to form B4C nanosheets with low formation energies. We find that there is minimal dependence of formation energies on cleavage planes and surface terminations, even though the bulk is not van der Waals layered. This anomalous stability of B4C nanosheets is found to be a result of surface reconstructions that are unique to B-rich systems. While the density of states of the bulk B4C indicate that it is a semiconductor, the B4C nanosheets are found to be predominantly metallic. We attribute this metallic behavior to a redistribution of charges on the surface bonds of the films. The Seebeck coefficients of the B4C films remain comparable to those of the bulk and are nearly constant as a function of temperature. Our results provide guidance for experimental synthesis efforts and future application of B4C nanosheets in nanoelectronic and thermoelectric applications.

Physics↗
DOE OSTI2019

A new metal transfer process for van der Waals contacts to vertical Schottky-junction transition metal dichalcogenide photovoltaics

Two-dimensional transition metal dichalcogenides are promising candidates for ultrathin optoelectronic devices due to their high absorption coefficients and intrinsically passivated surfaces. To maintain these near-perfect surfaces, recent research has focused on fabricating contacts that limit Fermi-level pinning at the metal-semiconductor interface. Here, we develop a new, simple procedure for transferring metal contacts that does not require aligned lithography. Using this technique, we fabricate vertical Schottky-junction WS 2 solar cells, with Ag and Au as asymmetric work function contacts. Under laser illumination, we observe rectifying behavior and open-circuit voltage above 500 mV in devices with transferred contacts, in contrast to resistive behavior and open-circuit voltage below 15 mV in devices with evaporated contacts. One-sun measurements and device simulation results indicate that this metal transfer process could enable high specific power vertical Schottky-junction transition metal dichalcogenide photovoltaics, and we anticipate that this technique will lead to advances for two-dimensional devices more broadly.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High Temperature Thick Film Sensor Development Based on Refractory Oxide Semiconductors

Solid-state, high-temperature sensing devices are required for accurate temperature, strain/stress, and failure monitoring for a range of advanced manufacturing, transportation, and military applications. High temperature conditions limit sensing strategies, where typically traditional metal and semiconductor materials are unstable, and the sensing options are limited to optical spectroscopy methods. In addition, strategies to embed the sensors directly within active components and protective thermal refractory are of interest that permit near-environment sensing which is not possible with the traditional electronic materials and components. Rare-earth chromite semiconductors exhibit some properties of interest for high temperature sensing technologies, such as: high microstructure and chemical stability, relatively high electronic conductivity at high temperatures, and relative thermal expansion coefficient matching to refractory thermal protective insulation (such as high-zirconia and -alumina ceramics). In this work, n-type and p-type doped lanthanum chromites compositions were computationally modelled and prepared, and the electrical, thermoelectric, and thermomechanical properties were measured for the obtained material systems. A few compositions were then processed into thick film health and temperature sensors and tested at high temperatures. To establish relative stability under harsh environment conditions, post- mortem microstructure and chemical composition was characterized after extended and cycle testing at high temperatures.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

A chemical kinetics perspective on thermoelectric transport

There is a growing community of chemists and materials scientists exploring thermoelectric properties of organic, polymeric, hybrid, and composite materials. Many of these materials are nondegenerate semiconductors, meaning that the Fermi and transport charge transport energy levels are significantly offset. Others are ionic conductors. While the meaning of the essential parameters electrical conductivity (σ) and Seebeck coefficient (S, the voltage difference per degree of temperature difference) are accessible, the origins of S are not readily apparent to one trained mainly in chemistry. The purpose of this manuscript is to illustrate S as being the result of a steady state difference between concentrations of two designations of charge carriers, those on hotter and those on colder sides of a material sample, analogous to the equilibrium among interconverting chemical species that differ in enthalpy and entropy. The ion-based Seebeck coefficient, also known as the Soret effect, can be explained using principles similar to those applicable to electrons and holes. We hope that this analysis leads to wider understanding of the origins of S through an explanation using the language of chemical kinetics and thermodynamics, and appreciation of ways that thermoelectric efficiency can be enhanced in emerging materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The highly disordered Zintl phase Ca 10 GdCdSb 9 – New example of a p-type semiconductor with remarkable thermoelectric properties

Ca 10 GdCdSb 9 is a new Zintl phase with a large unit cell volume (~2500 Å 3 ) and a very complex, disordered structure, which can drive the realization of ultralow thermal conductivity in this material. The measured Seebeck coefficient, α, for single-crystalline Ca 10 GdCdSb 9 approaches 350 μV/K at 600 K. The experimentally determinedelectrical resistivity of Ca 10 GdCdSb 9 is very low, leading to a remarkably high-power factor PF of 23.2 μW/cm·K 2 at 460 K. Furthermore, the extraordinary PF value in this material, higher than those of the currently known state-of-the-art materials within the same temperature range, suggests that the Ca 10 RECdSb 9 material system (RE = rare earth metal) could serve as a viable playground to harnessing new efficient thermoelectric generators.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Weighted Mobility

Engineering semiconductor devices requires an understanding of charge carrier mobility. Typically, mobilities are estimated using Hall effect and electrical resistivity meausrements, which are are routinely performed at room temperature and below, in materials with mobilities greater than 1 cm 2 V -1 s -1 . With the availability of combined Seebeck coefficient and electrical resistivity measurement systems, it is now easy to measure the weighted mobility (electron mobility weighted by the density of electronic states). A simple method to calculate the weighted mobility from Seebeck coefficient and electrical resistivity measurements is introduced, which gives good results at room temperature and above, and for mobilities as low as 10 -3 cm 2 V -1 s -1 , <!--FIGURE--> μ w = 331 c m 2 V s ( m Ω c m ρ ) ( T 300 K ) - 3 / 2 [ e x p [ | S | k B / e - 2 ] 1 + exp [ - 5 ( | S | k B / e - 1 ) ] + 3 π 2 | S | k B / e 1 + exp [ 5 ( | S | k B / e - 1 ) ] ] In this paper, μ w is the weighted mobility, ρ is the electrical resistivity measured in mΩ cm, T is the absolute temperature in K, S is the Seebeck coefficient, and k B /e = 86.3 µV K -1 . Weighted mobility analysis can elucidate the electronic structure and scattering mechanisms in materials and is particularly helpful in understanding and optimizing thermoelectric systems.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Structural Complexity and Tuned Thermoelectric Properties of a Polymorph of the Zintl Phase Ca 2 CdSb 2 with a Non-centrosymmetric Monoclinic Structure

The Zintl phase Ca 2 CdSb 2 was found to be dimorphic. Besides the orthorhombic Ca 2 CdSb 2 (-o), here we report on the synthesis, the structural characterization, and the thermoelectric transport properties of its monoclinic form, Ca 2 CdSb 2 (-m), and its Lu-doped variant Ca 2–x Lu x CdSb 2 (x ≈ 0.02). The monoclinic structure exhibits complex structural characteristics and constitutes a new structure type with the non-centrosymmetric space group Cm (Z = 30). The electrical resistivity ρ(T) measured on single crystals of both phases portrays a transition from a semiconductor to a degenerate p-type semiconductor upon doping with Lu and with an attendant change in the Hall carrier concentration nH from 7.15 × 10 18 to 2.30 × 10 19 cm –3 at 300 K. The Seebeck coefficient S(T) of both phases are comparable and indicate a hole-dominated carrier transport mechanism with magnitudes of 133 and 116 μV/K at 600 K for Ca 2 CdSb 2 (-m) and Ca 2–x Lu x CdSb 2 , respectively. The convoluted atomic bonding with an attendant large unit cell volume of ~4365 Å 3 drives a putative low thermal conductivity in these materials resulting in a power factor PF of 1.63 μW/cm K 2 and an estimated thermoelectric figure of merit zT of ~0.5 for Ca 2–x Lu x CdSb 2 at 600 K. Furthermore, differential scanning calorimetry results reveal the stability of these phases up to about 960 K, making them candidates for moderate temperature thermoelectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The Zintl pnictides Yb10CdSb9 and Yb14CdSb11: New candidate thermoelectric materials

The synthesis of new materials is the lifeline of solid-state science, and it continues to offer us unique opportunities for testing various theoretical formulations and models on a practical material. Such an avenue, therefore, provides a breeding ground for technological innovations and advancements that can completely revolutionize our world. Here, we report the results of our exploratory syntheses in the Yb–Cd–Sb compositional space that lead to the identification of two new Zintl antimonides, namely, Yb10CdSb9 and Yb14CdSb11. Their crystal structures were established via single-crystal X-ray diffraction methods; the basic electronic and transport properties of the new materials were also characterized. Yb10CdSb9 crystallizes in a disordered variant of the tetragonal Ca10LiMgSb9 structure type with unit cell parameters a = 11.8473(8) Å and c = 17.1302(12) Å (space group P42/mnm). Yb14CdSb11 crystallizes in the tetragonal Ca14AlSb11 structure type with unit cell parameters: a = 16.605(3) Å and c = 12.144(7) Å (space group I41/acd). Although the structures of both compounds can be rationalized within the framework of the Zintl formalism, based on the partitioning of the valence electrons in the much disordered Yb10CdSb9 phase, the charge is indicative of a slightly electron-rich composition. Electronic structure calculations in both cases support the notion of intrinsic semiconductor behavior, as expected for a Zintl phase. The temperature dependence of the electrical resistivity of a single crystal of Yb10CdSb9 is in line with that, and the evolution of the Seebeck coefficient indicates an electron-dominated transport mechanism, and a respectable power factor of 0.71 μW/cm K2 at 460 K can be calculated for Yb10CdSb9. The electrical resistivity of Yb14CdSb11, however, evolves in a semimetallic manner, which could suggest an overdoped sample or degenerate semiconducting behavior.

Ogunbunmi, Michael O. (ORCID:0000000253409198)↗
DOE OSTI2024

Resolving electron and hole transport properties in semiconductor materials by constant light-induced magneto transport

The knowledge of minority and majority charge carrier properties enables controlling the performance of solar cells, transistors, detectors, sensors, and LEDs. Here, we developed the constant light induced magneto transport method which resolves electron and hole mobility, lifetime, diffusion coefficient and length, and quasi-Fermi level splitting. We demonstrate the implication of the constant light induced magneto transport for silicon and metal halide perovskite films. We resolve the transport properties of electrons and holes predicting the material’s effectiveness for solar cell application without making the full device. The accessibility of fourteen material parameters paves the way for in-depth exploration of causal mechanisms limiting the efficiency and functionality of material structures. To demonstrate broad applicability, we further characterized twelve materials with drift mobilities spanning from 10 –3 to 10 3 cm 2 V –1 s –1 and lifetimes varying between 10 –9 and 10 –3 seconds. The universality of our method its potential to advance optoelectronic devices in various technological fields.

14 SOLAR ENERGY↗
DOE OSTI2023

Impact of Irradiation-Induced Filter Heating on Calibration of NIR-Longpass-Filtered Reference Solar Cells

Reference solar cells play a crucial role in determining the performance of photovoltaic (PV) devices. In the performance calibration chain of mainstream single-junction PV technologies, common reference cell types include Si, KG-filtered Si, and GaAs cells. For emerging multijunction (MJ) PV technologies, such as CdTe/Si and perovskite/Si, Si reference cells with colored glass near-infrared-longpass (LP) filters like Schott RG-715 and 850 glass have been proposed. They offer a better spectral response that matches the bottom junctions of the emerging MJs, which could lead to lower uncertainties in performance measurements. However, this article reveals a prominent decrease in short-circuit current (ISC) during National Renewable Energy Laboratory's primary calibration over the course of minutes when using this type of LP-filtered reference cell, which could result in unacceptable measurement errors. Unlike quartz or KG filter glasses, LP colored glass filters demonstrate temperature-sensitive cut-on wavelength. When incident irradiance reaches these LP-filtered reference cells, the increased temperature due to light absorption causes a shift of the cut-on to longer wavelength. As a result, the device I SC exhibits a continuous decrease (approximately a 2.5% drop with RG850 LP filter in a 5-min duration) even when the device temperature is controlled at 25 degrees C. To address the temperature gradient issue between colored glass LP filter and the reference cell, we propose the direct integration of thin-film LP semiconductor layer on reference cells. This type of LP-filter-integrated cell has shown minimal temperature-related I SC variation and can serve as a more reliable reference cell source for accurate performance measurements.

14 SOLAR ENERGY↗