Search NASA⌕ Search

SEARCH · Search NASA

Results for “conical shocks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Jupiter entry simulation with the ANAA shock tube

An annular arc accelerator (ANAA) shock tube has been built which produces shock velocities and pressures that simulate entry into the atmosphere of Jupiter. The ANAA driver deposits the energy of an arc discharge into a flowing gas, which then expands and cools without any delay for the opening of a diaphragm. A flow transducer, trigger system, and spark gap switches have been developed to coordinate the flow from a high-pressure helium driver with the discharge from a 300-kJ capacitor bank. Shock velocities up to 47 km/sec have been produced in 1.0 torr of hydrogen with the ANAA shock tube, compared with 35 km/sec velocity produced in a conical arc driver with three times the available energy. Attenuation with the ANAA shock tube is comparable to that of a conical arc driver shock tube, and initial spectroscopic measurements indicate that an impurity-free test slug is formed behind the shock wave.

Leibowitz, L. P.↗
DOE OSTI2023

Dynamics of Three-Dimensional Shock-Wave/Boundary-Layer Interactions

Advances in measuring and understanding separated, nominally two-dimensional (2D) shock-wave/turbulent-boundary-layer interactions (STBLI) have triggered recent campaigns focused on three-dimensional (3D) STBLI, which display far greater configuration diversity. Nonetheless, unifying properties emerge for semi-infinite interactions, taking the form of conical asymptotic behavior where shock-generator specifics become insignificant. The contrast between 2D and 3D separation is substantial; the skewed vortical structure of 3D STBLI reflects the essentially 2D influence of the boundary layer on the 3D character of the swept shock. As with 2D STBLI, conical interactions engender prominent spectral content below that of the turbulent boundary layer. However, the uniform separation length scale, which is crucial to normalizing the lowest-frequency dynamics in 2D STBLI, is absent. Comparatively, the spectra of 3D STBLI are more representative of the mid-frequency, convective, shear-layer dynamics in 2D, while phenomena associated with 2D separation-shock breathing are muted. Asymptotic behavior breaks down in many regions important to 3D-STBLI dynamics, occurring in a configuration-dependent manner. Aspects of inceptive regions near shock generators and symmetry planes are reviewed. Focused efforts toward 3D modal and nonmodalanalyses, moving-shock/boundary-layer interactions, fluid/structure interactions, and flow control are suggested as directions for future work.

42 ENGINEERING↗
DOE OSTI2022

Morphology of shocked lateral outflows in colliding hydrodynamic flows

Supersonic interacting flows occurring in phenomena, such as protostellar jets, give rise to strong shocks and have been demonstrated in several laboratory experiments. To study such colliding flows, we use the AstroBEAR AMR code to conduct hydrodynamic simulations in three dimensions. Here, we introduce variations in the flow parameters of density, velocity, and cross-sectional radius of the colliding flows in order to study the propagation and conical shape of the bow shock formed by collisions between two, not necessarily symmetric, hypersonic flows. We find that the motion of the interaction region is driven by imbalances in ram pressure between the two flows, while the conical structure of the bow shock is a result of shocked lateral outflows being deflected from the horizontal when the flows are of differing cross sections.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1972

Evaluation of boundary layer transition criteria for space shuttle orbiter entry

A comparison was made of the effect of boundary layer transition on center-line heating in a conical and a normal-shock flow field. It was shown that the time of transition onset (and, hence, the heating parameter) is significantly influenced by the choice of transition criterion in the normal-shock flow but that this parameter is much less sensitive to the transition criterion in a conical flow field. An evaluation of the effects of boundary layer transition on center-line heating in the conical flow field has shown that the temperatures are less affected by the use of various transition crieria than are heat loads. This difference is due to the delay in the time of transition onset predicted by those criteria with high transition Reynolds numbers. The criteria which predict the most severe thermal environment are those of fully turbulent flow throughout the entry, because transition occurs early in the trajectory for each of these criteria, they tend to predict similar values of maximum temperature and total heat load especially at center-line locations aft of 0.6. Evaluation of center-line heating generated by various trajectory shaping approaches has shown that the maximum surface temperature distribution was not significantly affected by the shaping technique. However, the heat load distribution is influenced, particularly on the forward portion of the vehicle.

Helms, V. T., III↗
NASA NTRS1990

Mixer-ejector nozzle for jet noise suppression

An aero/acoustic model test of a mixer-ejector nozzle was conducted at the 9 x 15 foot low-speed acoustic wind tunnel at NASA Lewis Research Center. The objective of the test was to get a preliminary assessment of ejector pumping and noise reduction potential of this device for possible application in the exhaust system of an advanced supersonic civil transport. The results of the test showed that goal levels of pumping were achieved. Exit pressure/temperature traverse data showed that there was good mixing between the primary and secondary streams. Acoustics data were dominated by shock noise; jet mixing noise levels were low because of a facility limit on primary temperature. The mixer-ejector did significantly reduce shock noise relative to the baseline conic nozzle. Because the relative magnitudes of jet mixing noise and shock noise were not in the correct proportion to properly model engine noise, an Effective Perceived Noise Level (EPNL) assessment was precluded.

Lord, W. K.↗
NASA NTRS1972

Computer program for calculating supersonic flow on the windward side conical delta wings by the method of lines

A user's manual is presented for a program that calculates the supersonic flow on the windward side of conical delta wings with shock attached at the sharp leading edge by the method of lines. The program also has a limited capability for computing the flow about circular and elliptic cones at incidence. It provides information including the shock shape, flow field, isentropic surface-flow properties, and force coefficients. A description of the program operation, a sample computation, and a FORTRAN 4 program listing are included.

Klunker, E. B.↗
NASA NTRS1972

A conical arc driver for high-energy test facilities.

Review of some exploratory test results for an electrical discharge driver with a conical-shaped arc chamber. The characteristics of the discharge cycle in the conical chamber and the shock tube performance are described, and the obtained results are compared with those reported by Menard (1971).

Dannenberg, R. E.↗
NASA NTRS1975

Application of blast wave theory to explosive propulsion

An analysis was carried out by using blast wave theory to delineate the important aspects of detonating explosives in nozzles, such as flow and wave phenomena, characteristic length and time scales, and the parameters on which the specific impulse is dependent. The propulsive system utilizes the momentum of the ambient gas set into motion in the nozzle by the explosion. A somewhat simplified model was considered for the situation where the mass of ambient gas in the nozzle is much greater than the mass of gas produced in the explosion, a condition of interest for dense atmospheres, e.g., near the surface of Venus. Instantaneous detonation and energy release was presumed to occur at the apex of a conical nozzle, and the shock wave generated by the explosion was taken to propagate as a spherical wave, thereby setting the ambient gas in the nozzle into one-dimensional radially outward motion.

Back, L. H.↗
NASA NTRS1991

On the scale of surface features in hypersonic swept shock boundary-layer interactions

A parametric study of a Mach 8 fin-induced shock interaction with a turbulent boundary layer was performed in a shock tunnel using surface oil-dot visualization and surface pressure measurements. The study showed that the interaction was separated and secondary separation was detected for the strongest cases studied. Although the inviscid shock wave was close to the fin, the interaction was spread over large angular extents. The interaction showed inception to conical symmetry at the highest shock strengths. Additionally, the surface pressure distribution showed an extensive plateau region, with no distinct dip associated with strongly separated interactions. Between the fin and the inviscid shock, the surface pressure rose rapidly but did not approach the downstream inviscid shock, the surface pressure rose rapidly but did not approach the downstream inviscid value.

Pace, E. G.↗
NASA NTRS1992

Time dependent heat transfer rates in high Reynolds number hypersonic flowfields

Time dependent heat transfer rates have been calculated from time dependent temperature measurements in the vicinity of shock-wave boundary-layer interactions due to conical compression ramps on an axisymmetric body. The basic model is a cylindrical body with a 10 degree conical nose. Four conical ramps, 20, 25, 30, and 35 degrees serve as shock wave generators. Flowfield surveys have been made in the vicinity of the conical ramp vertex, the separation point, and the reattachment point. A significant effort was made to characterize the natural frequencies and relative powers of the resulting fluctuations in heat transfer rates. This research effort, sponsored jointly by NASA and the Air Force, was conducted in the Air Force Flight Dynamics Directorate High Reynolds Facility. The nominal freestream Mach number was 6, and the freestream Reynolds numbers ranged from 2.2 million/ft to 30.0 million/ft. Experimental results quantify temperature response and the resulting heat transfer rates as a function of ramp angle and Reynolds number. The temperature response within the flowfield appears to be steady-state for all compression ramp angles and all Reynolds numbers, and hence, the heat transfer rates appear to be steady-state.

Flanagan, Michael J.↗
NASA NTRSDate not supplied

Flow and Noise from Supersonic Plug Nozzles

Nozzles with external plugs are candidates for propulsion of future supersonic aircraft. A model-scale experimental study is conducted exploring the flow and noise characteristics of various plug nozzles. For a given outer nozzle, the plug geometry is varied from conic with various half-angles (lengths) to plugs designed by the method of characteristics (MoC) as well as truncated and porous plugs. So far, noise characteristics and schlieren flow visualization data have been acquired. Limited numerical simulations have also been done addressing thrust performance. The simulations show that the MoC plugs out-perform the conic cases, especially around high Mach number cruise conditions. The experimental data, however, show that the MoC plugs are noisy relative to the conic cases at low Mach number landing and takeoff (LTO) conditions. The increased noise (with MoC at LTO) is accompanied by unsteady turbulent structures and increased jet spreading, as seen in schlieren pictures. At LTO, the longest conic plug is found to be the least noisy. Furthermore, a porous surface on the long conic plug effectively suppresses broadband shock associated noise (BBSN) at higher Mach numbers. Thus, a dilemma remains. MoC design gives best thrust performance at cruise but it is noisy at LTO. A long conic plug, on the other hand, is quieter at LTO but may have unacceptable thrust at cruise.

jets↗
NASA NTRSDate not supplied

Flow and noise from supersonic plug nozzles

Nozzles with external plugs are candidates for propulsion of future supersonic aircraft. A model-scale experimental study is conducted exploring the flow and noise characteristics of various plug nozzles. For a given outer nozzle, the plug geometry is varied from conic with various half-angles (lengths) to plugs designed by the method of characteristics (MoC) as well as truncated and porous plugs. So far, noise characteristics and schlieren flow visualization data have been acquired. Limited numerical simulations have also been done addressing thrust performance. The simulations show that the MoC plugs out-perform the conic cases, especially around high Mach number cruise conditions. The experimental data, however, show that the MoC plugs are noisy relative to the conic cases at low Mach number landing and takeoff (LTO) conditions. The increased noise (with MoC at LTO) is accompanied by unsteady turbulent structures and increased jet spreading, as seen in schlieren pictures. At LTO, the longest conic plug is found to be the least noisy. Furthermore, a porous surface on the long conic plug effectively suppresses broadband shock associated noise (BBSN) at higher Mach numbers. Thus, a dilemma remains. MoC design gives best thrust performance at cruise but it is noisy at LTO. A long conic plug, on the other hand, is quieter at LTO but may have unacceptable thrust at cruise.

jets↗
NASA NTRS1998

Computational Analysis of Shock Layer Emission Measurements in an Arc-Jet Facility

This paper reports computational analysis of radiation emission experiments in a high enthalpy arc-jet wind tunnel at NASA Ames Research Center. Recently, as part of ongoing arc-jet characterization work, spectroscopic radiation emission experiments have been conducted at the 20 MW NASA Ames arc-jet facility. The emission measurements were obtained from the arc-jet freestream and from a shock layer formed in front of flatfaced models. Analysis of these data is expected to provide valuable information about the thermodynamic state of the gas in the arc-jet freestream and in the shock layer as well as thermochemical equilibration processes behind the shock in arc-jet flows. Knowledge of the thermodynamic state of the gas in arc-jet test flows and especially within the shock layer is essential to interpret the heat transfer measurements such as in surface catalysis experiments. The present work is a continuation of previous work and focuses on analysis of the emission data obtained at relatively low-pressure conditions for which the arc-jet shock layer is expected to be in thermal and chemical nonequilibrium. Building blocks of the present computational analysis are: (1) simulation of nonequilibrium expanding flow in the converging-diverging conical nozzle and supersonic jet; (2) simulation of nonequilibrium shock layer formed in front of the flat-faced cylinder model; and (3) prediction of line-of-sight radiation from the computed flowfield. For computations of the nonequilibrium flow in the conical nozzle and shock layer, multi-temperature nonequilibrium codes with the axisymmetric formulation are used. For computations of line-of-sight radiation. a nonequilibrium radiation code (NEQAIR) is used to predict emission spectra from the computed flowfield. Computed line-of-sight averaged flow properties such as vibrational and rotational temperatures, species number densities within the shock layer will be compared with those deduced from the experimental spectra. Detailed comparisons of computational and experimental spectra will also be presented.

Gokcen, Tahir↗
NASA NTRS1991

Pressure and temperature fluctuations in an axisymmetric flowfield due to shock-boundary layer interactions at high Reynolds numbers at Mach 6

Pressure and temperature fluctuations have been meausred in the vicinity of shock wave-boundary layer interactions due to conical compression ramps on an axisymmetric body. The basic model is a cylindrical body with a 10-deg conical nose. Four conical ramps of vertex angles, 20, 25, 30, and 35 deg serve as shock wave generators. Surface temperature and pressure surveys have been made in the vicinity of the conical ramp vertex, the separation point, and the reattachment point. The temperature response within the flowfield appears to be steady-state for all compression ramp angles and all Reynolds numbers. The pressure response shows some oscillations in the vicinity of the separation point. The characteristic frequency of these fluctuations appears to be in the range from 200 to 1200 Hz with most of the power near 400 Hz. These data indicate the flowfield to be steady-state for all locations with the exception of localized pressure fluctuations in the vicinity of the separation point.

Flanagan, M. J., Jr.↗
NASA NTRS1994

Interpretation of waverider performance data using computational fluid dynamics

A computational study was conducted to better understand experimental results obtained from wind-tunnel tests of a Mach 4 conical-flow-derived waverider and a comparative reference configuration, which showed that the aerodynamic performance of the reference configuration was slightly better than that of the waverider. The computational results showed that the predicted surface pressure values and the integrated lift and drag coefficients were much lower for the reference model because the reference model bottom is an expansion surface. However, the lift-drag ratios for the reference model were higher due to a relatively low drag for a comparable amount of lift. The results also showed that the reference model exhibited the same shock attachment characteristics as the conical-flow-derived waverider, and is therefore also a waverider. The shock attachment characteristic gives the waverider a performance advantage over conventional hypersonic vehicles, and the results suggest that altering the bottom surface does not cause significant performance degradation. Flowfield solutions also show that the conical-flow waverider model has better propulsion/airframe integration characteristics than the reference configuration. The results also suggest that generating flowfields other than conical ones may be used to design waveriders with improved aerodynamic performance.

COMPUTATIONAL FLUID DYNAMICS↗